The DOI matches its Crossref record; 37 of the 37 references it cites were found in a registry or an index.
Steel fibres reinforced 3D printed concrete: Influence of fibre sizes on mechanical performance
Open accessAbstract
Abstract Mechanical properties of high-performance printing concrete reinforced with steel fibres with different lengths (3 and 6 mm) at different fibre volume contents (0.25%, 0.5%, 0.75% and 1%) are investigated. The experimental results substantiate that critical length and volume fraction of fibres, particularly 0.75% and 1% steel fibres of 6 mm length, in conjunction with fibre alignment, are of major importance for generating fibre bridging mechanism to improve flexural performance. As a result, enhanced load-carrying capacity, deflection hardening behaviour and less brittle failure can be achieved in printed specimens tested in a specific direction. Compressive and flexural strengths of printed concrete are in a range of 70-111 MPa and 6–15 MPa compared with the cast control of 90–113 MPa and 11–14 MPa, respectively. Results from micro-computed tomography scanning on hardened concrete without fibres reveal that the high-quality printed concrete has lower pore content, which is 8.8% compared with 9.8% and 11.4% in the cast and low-quality printed samples, respectively. It also shows that more than 90% of extruded fibres align within 0°-30° from the filament orientation.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Mix design and fresh properties for high-performance printing concrete
Le, T. T., Austin, S. A., Lim, S., Buswell, R. A., Gibb, A. G. F., & Thorpe, T. (2012) · Materials and Structures · doi:10.1617/s11527-012-9828-z · Cited by 1,218
Rheological requirements for printable concretes
Roussel, N. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.04.005 · Cited by 1,203
Automated construction by contour crafting—related robotics and information technologies
Khoshnevis, B. (2004) · Automation in Construction · doi:10.1016/j.autcon.2003.08.012 · Cited by 1,161
Hardened properties of high-performance printing concrete
Le, T. T., Austin, S. A., Lim, S., Buswell, R. A., Law, R., Gibb, A. G. F., & Thorpe, T. (2012) · Cement and Concrete Research · doi:10.1016/j.cemconres.2011.12.003 · Cited by 1,020
A critical review of the use of 3-D printing in the construction industry
Wu, P., Wang, J., & Wang, X. (2016) · Automation in Construction · doi:10.1016/j.autcon.2016.04.005 · Cited by 1,002
Gosselin, C., Duballet, R., Roux, P., Gaudillière, N., Dirrenberger, J., & Morel, P. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.03.097 · Cited by 962
Early age mechanical behaviour of 3D printed concrete: Numerical modelling and experimental testing
Wolfs, R. J. M., Bos, F. P., & Salet, T. A. M. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.02.001 · Cited by 846
Wolfs, R. J. M., Bos, F. P., & Salet, T. A. M. (2019) · Cement and Concrete Research · doi:10.1016/j.cemconres.2019.02.017 · Cited by 836
Anisotropic mechanical performance of 3D printed fiber reinforced sustainable construction material
Panda, B., Paul, S. C., & Tan, M. J. (2017) · Materials Letters · doi:10.1016/j.matlet.2017.07.123 · Cited by 742
Effect of surface moisture on inter-layer strength of 3D printed concrete
Sanjayan, J., Nematollahi, B., Xia, M., & Marchment, T. (2018) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2018.03.232 · Cited by 713
Self-citationFresh and hardened properties of 3D printable cementitious materials for building and construction
Paul, S. C., Tay, Y. W. D., Panda, B., & Tan, M. J. (2018) · Archives of Civil and Mechanical Engineering · doi:10.1016/j.acme.2017.02.008 · Cited by 633
Ma, G., Li, Z., & Wang, L. (2018) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2017.12.051 · Cited by 616
Nerella, V. N., Hempel, S., & Mechtcherine, V. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.01.235 · Cited by 605
Wu, Z., Shi, C., He, W., & Wang, D. (2017) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2017.02.010 · Cited by 492
Rheological and harden properties of the high-thixotropy 3D printing concrete
Zhang, Y., Zhang, Y., She, W., Yang, L. H., Liu, G., & Yang, Y. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2018.12.061 · Cited by 475
Properties of 3D-printed fiber-reinforced Portland cement paste
Hambach, M., & Volkmer, D. (2017) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2017.02.001 · Cited by 470
Ultra-high performance concrete: From fundamental to applications
Azmee, N. M., & Shafiq, N. (2018) · Case Studies in Construction Materials · doi:10.1016/j.cscm.2018.e00197 · Cited by 449
Yoo, D.-Y., Kim, S., Park, G.-J., Park, J.-J., & Kim, S.-W. (2017) · Composite Structures · doi:10.1016/j.compstruct.2017.04.069 · Cited by 447
Mega-scale fabrication by Contour Crafting
Khoshnevis, B., Hwang, D., Yao, K. T., & Yeh, Z. (2006) · International Journal of Industrial and Systems Engineering · doi:10.1504/ijise.2006.009791 · Cited by 378
Laboratory x-ray micro-computed tomography: a user guideline for biological samples
du Plessis, A., Broeckhoven, C., Guelpa, A., & le Roux, S. G. (2017) · GigaScience · doi:10.1093/gigascience/gix027 · Cited by 374
Mesh reinforcing method for 3D Concrete Printing
Marchment, T., & Sanjayan, J. (2020) · Automation in Construction · doi:10.1016/j.autcon.2019.102992 · Cited by 347
Self-citationBarnett, S. J., Lataste, J.-F., Parry, T., Millard, S. G., & Soutsos, M. N. (2009) · Materials and Structures · doi:10.1617/s11527-009-9562-3 · Cited by 335
Mechtcherine, V., Grafe, J., Nerella, V. N., Spaniol, E., Hertel, M., & Füssel, U. (2018) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2018.05.202 · Cited by 332
Zhu, B., Pan, J., Nematollahi, B., Zhou, Z., Zhang, Y., & Sanjayan, J. (2019) · Materials & Design · doi:10.1016/j.matdes.2019.108088 · Cited by 305
Self-citationX-ray micro-computed tomography (μCT) for non-destructive characterisation of food microstructure
Schoeman, L., Williams, P., du Plessis, A., & Manley, M. (2016) · Trends in Food Science & Technology · doi:10.1016/j.tifs.2015.10.016 · Cited by 251
Li, Z., Li, W., & Ma, G. (2020) · Composites Part B Engineering · doi:10.1016/j.compositesb.2020.107796 · Cited by 233
Ductility of 3D printed concrete reinforced with short straight steel fibers
Bos, F. P., Bosco, E., & Salet, T. A. M. (2019) · Virtual and Physical Prototyping · doi:10.1080/17452759.2018.1548069 · Cited by 222
Micro-cable reinforced geopolymer composite for extrusion-based 3D printing
Ma, G., Li, Z., Wang, L., & Bai, G. (2019) · Materials Letters · doi:10.1016/j.matlet.2018.09.159 · Cited by 196
Development of a Viable Concrete Printing Process
Lim, S., Buswell, R., Le, T., Wackrow, R., Austin, S., Gibb, A., & Thorpe, T. (2011) · Proceedings of the International Symposium on Automation and Robotics in Construction (IAARC) · doi:10.22260/isarc2011/0124 · Cited by 192
Skarżyński, Ł., & Suchorzewski, J. (2018) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2018.06.182 · Cited by 171
Uniaxial Compression Behavior of Ultra-High Performance Concrete with Hybrid Steel Fiber
Wu, Z., Shi, C., He, W. L., & Wang, D. (2016) · Journal of Materials in Civil Engineering · doi:10.1061/(asce)mt.1943-5533.0001684 · Cited by 156
Functionally-graded fiber-reinforced cement composite: Processing, microstructure, and properties
Shen, B., Hubler, M. H., Paulino, G. H., & Struble, L. J. (2008) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2008.02.002 · Cited by 125
Qsymah, A., Sharma, R. K., Yang, Z., Margetts, L., & Mummery, P. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.09.020 · Cited by 118
Ríos, J. D., Leiva, C., Ariza, M. P., Seitl, S., & Cifuentes, H. (2019) · Materials & Design · doi:10.1016/j.matdes.2019.107582 · Cited by 98
Ma, G., Zhang, J., Li, W., Li, Z., & Sun, J. (2018) · Smart Materials and Structures · doi:10.1088/1361-665x/aac789 · Cited by 85
3D printing cement based ink, and it’s application within the construction industry
Jianchao, Z., Zhang, T., Faried, M., & Wengang, C. (2017) · MATEC Web of Conferences · doi:10.1051/matecconf/201712002003 · Cited by 62
Mechanical Properties Of Ultra High Performance Concrete
Prem, P. R., Bharatkumar, B. H., & Iyer, N. R. (2012) · Zenodo (CERN European Organization for Nuclear Research) · doi:10.5281/zenodo.1327940 · Cited by 49
Cited by
Wickramasinghe, S., Do, T., & Tran, P. (2020) · Polymers · doi:10.3390/polym12071529 · Cited by 1,052
Self-citationMix design concepts for 3D printable concrete: A review
Zhang, C., Nerella, V. N., Krishna, A., Wang, S., Zhang, Y., Mechtcherine, V., & Banthia, N. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2021.104155 · Cited by 421
Extrusion-based concrete 3D printing from a material perspective: A state-of-the-art review
Mohan, M. K., Rahul, A. V., De Schutter, G., & Van Tittelboom, K. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2020.103855 · Cited by 384
Metadata
- Authors
- Pham, L., Tran, P., & Sanjayan, J.
- Venue
- Construction and Building Materials
- Publisher
- Elsevier BV
- Published
- 2020-07
- Volume
- 250
- Pages
- 118785
- ISSN
- 0950-0618 (ISSN-L)
- OpenAlex
- W3014468256
- Cited by
- 296
- References
- 37
- FWCI
- 16.66
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.