The DOI matches its Crossref record; 15 of the 15 references it cites were found in a registry or an index.
Investigation on fish surimi gel as promising food material for 3D printing
Abstract
This paper presents the development of a new 3D printing food constructs based on fish surimi gel system. This study investigated the influence of NaCl addition on rheological property, gel strength, water holding capacity (WHC), water distribution and microstructure of surimi gel to be used as a material for 3D printing. The obtained results from rheological studies showed that the surimi gels made with 1.5 g NaCl/100 g surimi mixture can be used for 3D printing. NaCl addition is helpful for the slurry to flow out from the nozzle in time and then get viscous post-deposition for holding its shape. Moreover, the effects of the printing parameters on the geometrical accuracy and dimension of the printed surimi gel were also studied. In this particular printing system, the 2.0 mm nozzle diameter, 5.0 mm nozzle height, 28 mm/s nozzle moving speed and 0.003 cm3/s extrusion rate were the optimal parameters to print 3D samples with fine resolution, better matching with the target geometry, fewer point defects and no compressed deformation. The overall results suggested that the 3D printing based on surimi gel system is a promising method for producing complexed-shape food patterns.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
3d printing technologies applied for food design: Status and prospects
Godoi, F. C., Prakash, S., & Bhandari, B. R. (2016) · Journal of Food Engineering · doi:10.1016/j.jfoodeng.2016.01.025 · Cited by 939
Self-citationAn Overview of 3D Printing Technologies for Food Fabrication
Sun, J., Zhou, W., Huang, D., Fuh, J. Y. H., & Hong, G. S. (2015) · Food and Bioprocess Technology · doi:10.1007/s11947-015-1528-6 · Cited by 549
Additive manufacturing (AM) and nanotechnology: promises and challenges
Ivanova, O., Williams, C., & Campbell, T. (2013) · Rapid Prototyping Journal · doi:10.1108/rpj-12-2011-0127 · Cited by 461
Role of secondary structures in the gelation of porcine myosin at different pH values
Liu, R., Zhao, S.-M., Xiong, S.-B., Xie, B.-J., & Qin, L.-H. (2008) · Meat Science · doi:10.1016/j.meatsci.2008.02.014 · Cited by 340
CHAISAWANG, M., & SUPHANTHARIKA, M. (2006) · Food Hydrocolloids · doi:10.1016/j.foodhyd.2005.06.003 · Cited by 333
Recent developments in 3D printable composite materials
Kalsoom, U., Nesterenko, P. N., & Paull, B. (2016) · RSC Advances · doi:10.1039/c6ra11334f · Cited by 294
Material characterisation and process development for chocolate additive layer manufacturing
Hao, L., Mellor, S., Seaman, O., Henderson, J., Sewell, N., & Sloan, M. (2010) · Virtual and Physical Prototyping · doi:10.1080/17452751003753212 · Cited by 252
Printing on Food or Food Printing: a Review
Pallottino, F., Hakola, L., Costa, C., Antonucci, F., Figorilli, S., Seisto, A., & Menesatti, P. (2016) · Food and Bioprocess Technology · doi:10.1007/s11947-016-1692-3 · Cited by 181
Wang, L., Zhang, M., Bhandari, B., & Gao, Z. (2016) · Food Research International · doi:10.1016/j.foodres.2016.06.007 · Cited by 169
Self-citationLipton, J. I., Arnold, D., Nigl, F., López, N. R., Cohen, D., Norén, N., & Lipson, H. (2010) · doi:10.26153/tsw/15245 · Cited by 168
Cited by
Direct Ink Writing: A 3D Printing Technology for Diverse Materials
Saadi, M. A. S. R., Maguire, A., Pottackal, N. T., Thakur, M. S. H., Ikram, M. M., Hart, A. J., Ajayan, P. M., & Rahman, M. M. (2022) · Advanced Materials · doi:10.1002/adma.202108855 · Cited by 1,335
3D printing: Printing precision and application in food sector
Liu, Z., Zhang, M., Bhandari, B., & Wang, Y. (2017) · Trends in Food Science & Technology · doi:10.1016/j.tifs.2017.08.018 · Cited by 858
Self-citationLiu, Z., Bhandari, B., Prakash, S., Mantihal, S., & Zhang, M. (2019) · Food Hydrocolloids · doi:10.1016/j.foodhyd.2018.08.026 · Cited by 530
Self-citationYang, F., Zhang, M., Bhandari, B., & Liu, Y. (2018) · LWT · doi:10.1016/j.lwt.2017.08.054 · Cited by 479
Self-citation3D printing technology: The new era for food customization and elaboration
Dankar, I., Haddarah, A., Omar, F. E. L., Sepulcre, F., & Pujolà, M. (2018) · Trends in Food Science & Technology · doi:10.1016/j.tifs.2018.03.018 · Cited by 471
Metadata
- Authors
- Wang, L., Zhang, M., Bhandari, B., & Yang, C.
- Venue
- Journal of Food Engineering
- Publisher
- Elsevier BV
- Published
- 2018-03
- Volume
- 220
- Pages
- 101-108
- ISSN
- 0260-8774 (ISSN-L)
- OpenAlex
- W2599517856
- Cited by
- 476
- References
- 15
- FWCI
- 17.43
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Investigation on fish surimi gel as promising food material for 3D printing. https://app.cochat.ai/papers/10.1016/j.jfoodeng.2017.02.029
- The paper
- Wang, L., Zhang, M., Bhandari, B., & Yang, C. (2018). Investigation on fish surimi gel as promising food material for 3D printing. Journal of Food Engineering. https://doi.org/10.1016/j.jfoodeng.2017.02.029
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.