The DOI matches its Crossref record; 34 of the 34 references it cites were found in a registry or an index.
Defect characteristics and analysis of their variability in metal L-PBF additive manufacturing
Open accessAbstract
Additive manufacturing (AM) has provided an opportunity for fabricating complex parts. Fabricating these parts without defects is currently a challenge. Therefore, understanding AM defects is fundamental to the structural integrity of load carrying components, failure analysis, and defect-based modeling of mechanical performance. This work investigates defect content of metal AM specimens and correlations between defect characteristics (size, sphericity/circularity, aspect ratio) using 2D and 3D defect characterization techniques. Distributions of defect characteristics based on location throughout AM specimens were analyzed and the variabilities of defect characteristics within these specimens were studied. Laser-Based Power Bed Fusion (L-PBF) specimens manufactured with different metals, different AM machines and built directions, different surface conditions, and different thicknesses were evaluated. Significant variability in defect characteristics based on location, especially in as-built surface specimens was observed. Well-optimized process parameters and post-processing reduced the overall volume fraction of defects, and the specified variabilities, and resulted in a more random dispersion of defects around the specimens. 2D and 3D defect analysis showed similar trends regarding correlations between defect characteristics and provided complementary information about the actual defect content based on their resolution.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Annual Book of ASTM Standards 2003
Riyanto, L. (2003) · Cited by 5,334
Leuders, S., Thöne, M., Riemer, A., Niendorf, T., Tröster, T., Richard, H. A., & Maier, H. J. (2013) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2012.11.011 · Cited by 1,475
King, W. E., Anderson, A. T., Ferencz, R. M., Hodge, N. E., Kamath, C., Khairallah, S. A., & Rubenchik, A. M. (2015) · Applied Physics Reviews · doi:10.1063/1.4937809 · Cited by 1,258
Xu, W., Brandt, M., Sun, S., Elambasseril, J., Liu, Q., Latham, K., Xia, K., & Qian, M. (2015) · Acta Materialia · doi:10.1016/j.actamat.2014.11.028 · Cited by 1,245
Mechanical behavior of additive manufactured, powder-bed laser-fused materials
Mower, T. M., & Long, M. J. (2016) · Materials Science and Engineering: A · doi:10.1016/j.msea.2015.10.068 · Cited by 1,001
Rafi, H. K., Karthik, N. V., Gong, H., Starr, T. L., & Stucker, B. E. (2013) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-013-0658-0 · Cited by 987
Selective laser melting of biocompatible metals for rapid manufacturing of medical parts
Vandenbroucke, B., & Kruth, J. (2007) · Rapid Prototyping Journal · doi:10.1108/13552540710776142 · Cited by 981
Gong, H., Rafi, K., Gu, H., Janaki Ram, G. D., Starr, T., & Stucker, B. (2015) · Materials & Design · doi:10.1016/j.matdes.2015.07.147 · Cited by 940
Cornillot, J. L., & Milligan, S. P. (2016) · Cited by 894
Fatigue performance evaluation of selective laser melted Ti–6Al–4V
Edwards, P., & Ramulu, M. (2014) · Materials Science and Engineering: A · doi:10.1016/j.msea.2014.01.041 · Cited by 874
Kasperovich, G., Haubrich, J., Gussone, J., & Requena, G. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.05.070 · Cited by 818
Improvement of fatigue resistance and ductility of TiAl6V4 processed by selective laser melting
Kasperovich, G., & Hausmann, J. (2015) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2015.01.025 · Cited by 735
Comparison of density measurement techniques for additive manufactured metallic parts
Spierings, A. B., Schneider, M., & Eggenberger, R. (2011) · Rapid Prototyping Journal · doi:10.1108/13552541111156504 · Cited by 613
Tammas-Williams, S., Zhao, H., Léonard, F., Derguti, F., Todd, I., & Prangnell, P. B. (2015) · Materials Characterization · doi:10.1016/j.matchar.2015.02.008 · Cited by 590
du Plessis, A., Yadroitsev, I., Yadroitsava, I., & Le Roux, S. G. (2018) · 3D Printing and Additive Manufacturing · doi:10.1089/3dp.2018.0060 · Cited by 550
The Influence of Porosity on Fatigue Crack Initiation in Additively Manufactured Titanium Components
Tammas-Williams, S., Withers, P. J., Todd, I., & Prangnell, P. B. (2017) · Scientific Reports · doi:10.1038/s41598-017-06504-5 · Cited by 494
Seifi, M., Gorelik, M., Waller, J., Hrabe, N., Shamsaei, N., Daniewicz, S., & Lewandowski, J. J. (2017) · JOM · doi:10.1007/s11837-017-2265-2 · Cited by 422
Porosity Measurements and Analysis for Metal Additive Manufacturing Process Control
Slotwinski, J. A., Garboczi, E. J., & Hebenstreit, K. M. (2014) · Journal of Research of the National Institute of Standards and Technology · doi:10.6028/jres.119.019 · Cited by 408
Bagehorn, S., Wehr, J., & Maier, H. J. (2017) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2017.05.008 · Cited by 371
Hrabe, N., Gnäupel-Herold, T., & Quinn, T. (2017) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2016.04.022 · Cited by 355
Rafi, H. K., Starr, T. L., & Stucker, B. E. (2013) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-013-5106-7 · Cited by 335
Maskery, I., Aboulkhair, N. T., Corfield, M. R., Tuck, C., Clare, A. T., Leach, R. K., Wildman, R. D., Ashcroft, I. A., & Hague, R. J. M. (2016) · Materials Characterization · doi:10.1016/j.matchar.2015.12.001 · Cited by 317
Benedetti, M., Fontanari, V., Bandini, M., Zanini, F., & Carmignato, S. (2018) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2017.10.021 · Cited by 297
Seifi, M., Salem, A. A., Satko, D. P., Shaffer, J., & Lewandowski, J. J. (2016) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2016.06.001 · Cited by 291
Fatemi, A., Molaei, R., Sharifimehr, S., Phan, N., & Shamsaei, N. (2017) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2017.03.044 · Cited by 282
Self-citationTammas-Williams, S., Withers, P. J., Todd, I., & Prangnell, P. B. (2016) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-016-3429-3 · Cited by 269
Smith, J., Xiong, W., Yan, W., Lin, S., Cheng, P., Kafka, O. L., Wagner, G. J., Cao, J., & Liu, W. K. (2016) · Computational Mechanics · doi:10.1007/s00466-015-1240-4 · Cited by 255
Fatemi, A., Molaei, R., Simsiriwong, J., Sanaei, N., Pegues, J., Torries, B., Phan, N., & Shamsaei, N. (2019) · Fatigue & Fracture of Engineering Materials & Structures · doi:10.1111/ffe.13000 · Cited by 199
Self-citationMolaei, R., Fatemi, A., & Phan, N. (2018) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2018.07.035 · Cited by 191
Self-citationPorosity testing methods for the quality assessment of selective laser melted parts
Wits, W. W., Carmignato, S., Zanini, F., & Vaneker, T. H. J. (2016) · CIRP Annals · doi:10.1016/j.cirp.2016.04.054 · Cited by 190
Gu, H., Gong, H., Pal, D., Rafi, K., Starr, T. L., & Stucker, B. E. (2013) · doi:10.26153/tsw/15572 · Cited by 166
Standardized X-ray tomography testing of additively manufactured parts: A round robin test
du Plessis, A., & le Roux, S. G. (2018) · Additive manufacturing · doi:10.1016/j.addma.2018.09.014 · Cited by 102
Solubility of argon in laser additive manufactured α-titanium under hot isostatic pressing condition
Shao, S., Mahtabi, M. J., Shamsaei, N., & Thompson, S. M. (2017) · Computational Materials Science · doi:10.1016/j.commatsci.2017.01.040 · Cited by 80
Kantzos, C., Cunningham, R., Tari, V., & Rollett, A. D. (2017) · Computational Mechanics · doi:10.1007/s00466-017-1531-z · Cited by 79
Cited by
Metal additive manufacturing in aerospace: A review
Blakey-Milner, B., Gradl, P., Snedden, G., Brooks, M., Pitot, J., Lopez, E., Leary, M., Berto, F., & du Plessis, A. (2021) · Materials & Design · doi:10.1016/j.matdes.2021.110008 · Cited by 2,263
Sanaei, N., & Fatemi, A. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100724 · Cited by 1,029
Self-citationBenedetti, M., du Plessis, A., Ritchie, R. O., Dallago, M., Razavi, N., & Berto, F. (2021) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2021.100606 · Cited by 788
du Plessis, A., Yadroitsava, I., & Yadroitsev, I. (2020) · Materials & Design · doi:10.1016/j.matdes.2019.108385 · Cited by 712
Properties and applications of additively manufactured metallic cellular materials: A review
du Plessis, A., Razavi, N., Benedetti, M., Murchio, S., Leary, M., Watson, M., Bhate, D., & Berto, F. (2022) · Progress in Materials Science · doi:10.1016/j.pmatsci.2021.100918 · Cited by 623
Metadata
- Authors
- Sanaei, N., Fatemi, A., & Phan, N.
- Venue
- Materials & Design
- Publisher
- Elsevier BV
- Published
- 2019-11
- Volume
- 182
- Pages
- 108091
- ISSN
- 0264-1275 (ISSN-L)
- OpenAlex
- W2965169693
- Cited by
- 301
- References
- 34
- FWCI
- 16.05
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.