The DOI matches its Crossref record; 431 of the 431 references it cites were found in a registry or an index.
The chemistry of chemical recycling of solid plastic waste via pyrolysis and gasification: State-of-the-art, challenges, and future directions
Open accessAbstract
Abstract Chemical recycling of solid plastic waste (SPW) is a paramount opportunity to reduce marine and land pollution and to enable the incorporation of the circular economy principle in today's society. In addition to more conscious behaviors and wiser product design (“design for recycling”), a key challenge is the identification of the leading recycling technologies, minimizing the global warming potential in an industrially relevant context. Chemical recycling technologies based on pyrolysis and gasification are leading the way because of their robustness and good economics, but an improved understanding of the chemistry and more innovative reactor designs are required to realize a potential reduction of greenhouse gas emissions of more than 100 million tonnes of CO2-eq., primarily by more efficient use of valuable natural resources. The feed flexibility of thermal processes supports the potential of pyrolysis and gasification, however, the strong variability in time and space of blending partners such as multiple and co-polymers, additives, and contaminants (such as inorganic materials) calls for accurate assessment through fundamental experiments and models. Such complex and variable mixtures are strongly sensitive to the process design and conditions: temperature, residence time, heating rates – severity, mixing level, heat and mass transfer strongly affect the thermal degradation of SPW and its selectivity to valuable products. A prerequisite in improving design and performance is the ability to model conversion profiles and product distributions based on accurate rate coefficients for the dominating reaction families established using first-principle derived transport and thermodynamic properties. These models should also help with the “design for recycling” strategy to increase recyclability, for example by identifying additives that make chemical recycling difficult. Fundamental experiments of increased quality (accuracy, integrity, validity, replicability, completeness) together with improved deterministic kinetic models, systematically developed according to the reaction classes and rate rules approach, provide insights to identify optimal process conditions. This will allow shedding some light upon the important pathways involved in the thermal degradation of the feedstock and the formation/disappearance of desired or unwanted products. In parallel, the intrinsic kinetics of the dominating elementary reaction steps should be determined with higher accuracy, moving beyond single step kinetics retrieved from thermogravimetric analysis experiments. Together with more accurate kinetic parameters, better models to account for heat and mass transfer limitations also need to be further developed, since plastic degradation involves at least three phases (solid, liquid, gas), whose interactions should be accounted for in a more rigorous way. Novel experimental approaches (e.g. detailed feedstock and product characterization using comprehensive chromatographic techniques and photoionization mass spectrometry) and available computational tools (e.g. kinetic Monte Carlo, liquid phase, and heterogeneous theoretical kinetics) are needed to tackle these problems and improve our fundamental understanding of chemical recycling of SPW.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Items 201–400 of 431
Primary thermal degradation mechanisms of PET and PBT
Montaudo, G., Puglisi, C., & Samperi, F. (1993) · Polymer Degradation and Stability · doi:10.1016/0141-3910(93)90021-a · Cited by 224
Elordi, G., Olazar, M., Lopez, G., Artetxe, M., & Bilbao, J. (2011) · Industrial & Engineering Chemistry Research · doi:10.1021/ie200186m · Cited by 224
Li, X., Li, J., Zhou, G., Feng, Y., Wang, Y., Yu, G., Deng, S., Huang, J., & Wang, B. (2014) · Applied Catalysis A: General · doi:10.1016/j.apcata.2014.05.015 · Cited by 221
Miandad, R., Nizami, A. S., Rehan, M., Barakat, M. A., Khan, M. I., Mustafa, A., Ismail, I. M. I., & Murphy, J. D. (2016) · Waste Management · doi:10.1016/j.wasman.2016.09.023 · Cited by 219
Tzanetis, K. F., Posada, J. A., & Ramirez, A. (2017) · Renewable Energy · doi:10.1016/j.renene.2017.06.104 · Cited by 217
Conversion of mixed plastic wastes in a dual fluidized bed steam gasifier
Wilk, V., & Hofbauer, H. (2013) · Fuel · doi:10.1016/j.fuel.2013.01.068 · Cited by 215
Environmental biodegradation of synthetic polymers I. Test methodologies and procedures
Eubeler, J. P., Zok, S., Bernhard, M., & Knepper, T. P. (2009) · TrAC Trends in Analytical Chemistry · doi:10.1016/j.trac.2009.06.007 · Cited by 214
Fluidized bed waste incinerators: Design, operational and environmental issues
Van Caneghem, J., Brems, A., Lievens, P., Block, C., Billen, P., Vermeulen, I., Dewil, R., Baeyens, J., & Vandecasteele, C. (2012) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2012.03.001 · Cited by 213
The strength of multi-scale modeling to unveil the complexity of radical polymerization
D’hooge, D. R., Van Steenberge, P. H. M., Reyniers, M.-F., & Marin, G. B. (2016) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2016.04.002 · Cited by 212
Self-citationThe occurrence of microplastic contamination in littoral sediments of the Persian Gulf, Iran
Naji, A., Esmaili, Z., Mason, S. A., & Dick Vethaak, A. (2017) · Environmental Science and Pollution Research · doi:10.1007/s11356-017-9587-z · Cited by 212
Municipal solid waste management in a circular economy: A data-driven bibliometric analysis
Tsai, F. M., Bui, T.-D., Tseng, M.-L., Lim, M. K., & Hu, J. (2020) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2020.124132 · Cited by 210
Syngas from steam gasification of polyethylene in a conical spouted bed reactor
Erkiaga, A., Lopez, G., Amutio, M., Bilbao, J., & Olazar, M. (2013) · Fuel · doi:10.1016/j.fuel.2013.03.022 · Cited by 209
Recent Advances in Polycarbonate Recycling: A Review of Degradation Methods and Their Mechanisms
Antonakou, E. V., & Achilias, D. S. (2013) · Waste and Biomass Valorization · doi:10.1007/s12649-012-9159-x · Cited by 209
(1999) · Fuel and Energy Abstracts · doi:10.1016/s0140-6701(99)96253-7 · Cited by 209
Thermogravimetry as a tool to classify waste components to be used for energy generation
Heikkinen, J. M., Hordijk, J. C., de Jong, W., & Spliethoff, H. (2004) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2003.12.001 · Cited by 204
Miskolczi, N., Bartha, L., & Deák, G. (2006) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2005.01.056 · Cited by 203
Olefins from polyolefins and mixed plastics by pyrolysis
Kaminsky, W., Schlesselmann, B., & Simon, C. (1995) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/0165-2370(94)00830-t · Cited by 200
Mechanistic Modeling of Polymer Pyrolysis: Polypropylene
Kruse, T. M., Wong, H.-W., & Broadbelt, L. J. (2003) · Macromolecules · doi:10.1021/ma030322y · Cited by 200
Communities of Microbial Enzymes Associated with Biodegradation of Plastics
Bhardwaj, H., Gupta, R., & Tiwari, A. (2013) · Journal of Polymers and the Environment · doi:10.1007/s10924-012-0456-z · Cited by 198
Sogancioglu, M., Yel, E., & Ahmetli, G. (2017) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2017.07.157 · Cited by 198
Enzymatic degradation of polymers: A brief review
Banerjee, A., Chatterjee, K., & Madras, G. (2014) · Materials Science and Technology · doi:10.1179/1743284713y.0000000503 · Cited by 197
Plastics and Environmental Sustainability
Andrady, A. L. (2015) · Wiley eBooks · doi:10.1002/9781119009405 · Cited by 196
Magnier, L., Mugge, R., & Schoormans, J. (2019) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2018.12.246 · Cited by 196
Pyrolysis of Polyethylene in a Fluidized Bed Reactor
Conesa, J. A., Font, R., Marcilla, A., & Garcia, A. N. (1994) · Energy & Fuels · doi:10.1021/ef00048a012 · Cited by 194
Pyrolysis of poly(ethylene terephthalate) in a fluidised bed plant
Yoshioka, T., Grause, G., Eger, C., Kaminsky, W., & Okuwaki, A. (2004) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2004.06.001 · Cited by 193
Deactivation and regeneration of ZSM-5 zeolite in catalytic pyrolysis of plastic wastes
López, A., de Marco, I., Caballero, B. M., Adrados, A., & Laresgoiti, M. F. (2011) · Waste Management · doi:10.1016/j.wasman.2011.04.004 · Cited by 192
Aguado, J., Serrano, D. P., Miguel, G. S., Escola, J. M., & Rodríguez, J. (2006) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2006.06.004 · Cited by 188
Uncertainty driven theoretical kinetics studies for CH3OH ignition: HO2+CH3OH and O2+CH3OH
Klippenstein, S. J., Harding, L. B., Davis, M. J., Tomlin, A. S., & Skodje, R. T. (2011) · Proceedings of the Combustion Institute · doi:10.1016/j.proci.2010.05.066 · Cited by 186
Artetxe, M., Lopez, G., Amutio, M., Elordi, G., Olazar, M., & Bilbao, J. (2010) · Industrial & Engineering Chemistry Research · doi:10.1021/ie900557c · Cited by 186
Plastic waste as a novel substrate for industrial biotechnology
Wierckx, N., Prieto, M. A., Pomposiello, P., de Lorenzo, V., O'Connor, K., & Blank, L. M. (2015) · Microbial Biotechnology · doi:10.1111/1751-7915.12312 · Cited by 186
Refinery co-processing of renewable feeds
Bezergianni, S., Dimitriadis, A., Kikhtyanin, O., & Kubička, D. (2018) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2018.04.002 · Cited by 184
Blank, L. M., Narancic, T., Mampel, J., Tiso, T., & O’Connor, K. (2020) · Current Opinion in Biotechnology · doi:10.1016/j.copbio.2019.11.011 · Cited by 182
Rates of thermal degradation of polystyrene and polyethylene in a vacuum
Madorsky, S. L. (1952) · Journal of Polymer Science · doi:10.1002/pol.1952.120090203 · Cited by 181
Recycling and recovery of post-consumer plastic solid waste in a European context
Brems, A., Baeyens, J., & Dewil, R. (2012) · Thermal Science · doi:10.2298/tsci120111121b · Cited by 179
Assessment of Environmental Biodegradation of Synthetic Polymers
Andrady, A. L. (1994) · Journal of Macromolecular Science, Part C: Polymer Reviews · doi:10.1080/15321799408009632 · Cited by 179
Biodegradation of Polyethylene by Green Photosynthetic Microalgae
Vimal Kumar, R., Kanna, G. R., & Elumalai, S. (2017) · Journal of Bioremediation & Biodegradation · doi:10.4172/2155-6199.1000381 · Cited by 179
Faraca, G., Martinez-Sanchez, V., & Astrup, T. F. (2019) · Resources, Conservation and Recycling · doi:10.1016/j.resconrec.2019.01.014 · Cited by 176
Bayo, J., Rojo, D., & Olmos, S. (2019) · Environmental Pollution · doi:10.1016/j.envpol.2019.06.024 · Cited by 174
Kinetics of polystyrene pyrolysis in a conical spouted bed reactor
Aguado, R. (2003) · Chemical Engineering Journal · doi:10.1016/s1385-8947(02)00119-5 · Cited by 171
Vlachokostas, C., Michailidou, A. V., & Achillas, C. (2021) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2020.110563 · Cited by 170
Wax Formation in the Pyrolysis of Polyolefins in a Conical Spouted Bed Reactor
Aguado, R., Olazar, M., San José, Gaisán, B., & Bilbao, J. (2002) · Energy & Fuels · doi:10.1021/ef020043w · Cited by 168
Characteristics of polyethylene cracking in supercritical water compared to thermal cracking
Moriya, T., & Enomoto, H. (1999) · Polymer Degradation and Stability · doi:10.1016/s0141-3910(99)00026-9 · Cited by 167
Achilias, D. S., Kanellopoulou, I., Megalokonomos, P., Antonakou, E., & Lappas, A. A. (2007) · Macromolecular Materials and Engineering · doi:10.1002/mame.200700058 · Cited by 164
Mechanistic Modeling of Polymer Degradation: A Comprehensive Study of Polystyrene
Kruse, T. M., Woo, O. S., Wong, H.-W., Khan, S. S., & Broadbelt, L. J. (2002) · Macromolecules · doi:10.1021/ma020490a · Cited by 164
Renewable diesel blendstocks produced by hydrothermal liquefaction of wet biowaste
Chen, W.-T., Zhang, Y., Lee, T. H., Wu, Z., Si, B., Lee, C.-F. F., Lin, A., & Sharma, B. K. (2018) · Nature Sustainability · doi:10.1038/s41893-018-0172-3 · Cited by 164
Bornscheuer, U. T. (2016) · Science · doi:10.1126/science.aaf2853 · Cited by 159
Second-generation biofuels by co-processing catalytic pyrolysis oil in FCC units
Thegarid, N., Fogassy, G., Schuurman, Y., Mirodatos, C., Stefanidis, S., Iliopoulou, E. F., Kalogiannis, K., & Lappas, A. A. (2014) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2013.01.019 · Cited by 158
Unraveling Reaction Pathways and Specifying Reaction Kinetics for Complex Systems
Vinu, R., & Broadbelt, L. J. (2012) · Annual Review of Chemical and Biomolecular Engineering · doi:10.1146/annurev-chembioeng-062011-081108 · Cited by 158
Detailed mechanistic modeling of polymer degradation: application to polystyrene
Kruse, T. M., Woo, O. S., & Broadbelt, L. J. (2001) · Chemical Engineering Science · doi:10.1016/s0009-2509(00)00312-2 · Cited by 156
Environmental engineering: Stepwise pyrolysis of plastic waste
Bockhorn, H., Hentschel, J., Hornung, A., & Hornung, U. (1999) · Chemical Engineering Science · doi:10.1016/s0009-2509(98)00385-6 · Cited by 156
Artetxe, M., López, G., Elordi, G., Amutio, M., Bilbao, J., & Olazar, M. (2012) · Industrial & Engineering Chemistry Research · doi:10.1021/ie300178e · Cited by 154
Kinetics of pyrolysis of high density polyethylene. Comparison of isothermal and dynamic experiments
Ceamanos, J., Mastral, J. F., Millera, Á., & Aldea, M. E. (2002) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/s0165-2370(01)00183-8 · Cited by 153
Improving the circular economy via hydrothermal processing of high-density waste plastics
Pedersen, T. H., & Conti, F. (2017) · Waste Management · doi:10.1016/j.wasman.2017.06.002 · Cited by 153
Fundamental reactions of free radicals relevant to pyrolysis reactions
Poutsma, M. L. (2000) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/s0165-2370(99)00083-2 · Cited by 151
Conversion of post consumer polyethylene to the biodegradable polymer polyhydroxyalkanoate
Guzik, M. W., Kenny, S. T., Duane, G. F., Casey, E., Woods, T., Babu, R. P., Nikodinović‐Runić, J., Murray, M. T., & O’Connor, K. E. (2014) · Applied Microbiology and Biotechnology · doi:10.1007/s00253-013-5489-2 · Cited by 150
Environmental impact analysis of municipal solid waste incineration in African countries
Cudjoe, D., & Acquah, P. M. (2020) · Chemosphere · doi:10.1016/j.chemosphere.2020.129186 · Cited by 150
05/00491 Thermogravimetry as a tool to classify waste components to be used for energy generation
(2005) · Fuel and Energy Abstracts · doi:10.1016/s0140-6701(05)80492-8 · Cited by 150
Study of the Low Temperature Pyrolysis of PVC
Ma, S., Lu, J., & Gao, J. (2002) · Energy & Fuels · doi:10.1021/ef0101053 · Cited by 147
Experimental investigation on liquefaction of plastic waste to oil in supercritical water
Bai, B., Jin, H., Fan, C., Cao, C., Wei, W., & Cao, W. (2019) · Waste Management · doi:10.1016/j.wasman.2019.04.017 · Cited by 147
A review of recent developments and future prospects in gasification systems and their modeling
Janajreh, I., Adeyemi, I. A., Raza, S. S., & Ghenaï, C. (2020) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2020.110505 · Cited by 147
López, M. D. M. C., Ares‐Pernas, A., López, M. J. A., Latorre, A. L., Vilariño, J. M. L., & González-Rodríguez, M. V. (2014) · Materials Chemistry and Physics · doi:10.1016/j.matchemphys.2014.06.034 · Cited by 146
Evolution of aromatics in the thermal degradation of poly(vinyl chloride): A mechanistic study
Montaudo, G., & Puglisi, C. (1991) · Polymer Degradation and Stability · doi:10.1016/0141-3910(91)90019-n · Cited by 145
Gopinath, K. P., Nagarajan, V. M., Krishnan, A., & Malolan, R. (2020) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2020.123031 · Cited by 145
Kenny, S. T., Nikodinović‐Runić, J., Kaminsky, W., Woods, T., Babu, R. P., & O’Connor, K. E. (2012) · Applied Microbiology and Biotechnology · doi:10.1007/s00253-012-4058-4 · Cited by 143
Kinetic modeling of polyethylene and polypropylene thermal degradation
Ranzi, E., Dente, M., Faravelli, T., Bozzano, G., Fabini, S., Nava, R., Cozzani, V., & Tognotti, L. (1997) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/s0165-2370(97)00032-6 · Cited by 143
Self-citationBrems, A., Baeyens, J., Beerlandt, J., & Dewil, R. (2011) · Resources Conservation and Recycling · doi:10.1016/j.resconrec.2011.03.003 · Cited by 143
Vacuum pyrolysis of commingled plastics containing PVC II. Product analysis
Miranda, R., Pakdel, H., Roy, C., & Vasile, C. (2001) · Polymer Degradation and Stability · doi:10.1016/s0141-3910(01)00066-0 · Cited by 142
Vacuum pyrolysis of commingled plastics containing PVC I. Kinetic study
Miranda, R., Yang, J. R., Roy, C., & Vasile, C. (2001) · Polymer Degradation and Stability · doi:10.1016/s0141-3910(01)00048-9 · Cited by 142
Spallina, V., Velarde, I. C., Jimenez, J. A. M., Godini, H. R., Gallucci, F., & Annaland, M. V. S. (2017) · Energy Conversion and Management · doi:10.1016/j.enconman.2017.10.061 · Cited by 139
Aamir, E., Nagy, Z. K., Rielly, C. D., Kleinert, T., & Judat, B. (2009) · Industrial & Engineering Chemistry Research · doi:10.1021/ie900430t · Cited by 137
Mazaheri, H., Lee, K. T., Bhatia, S., & Mohamed, A. R. (2010) · Bioresource Technology · doi:10.1016/j.biortech.2010.04.072 · Cited by 137
Mechanistic Understanding of Thermochemical Conversion of Polymers and Lignocellulosic Biomass
Zhou, X., Broadbelt, L. J., & Vinu, R. (2016) · Advances in chemical engineering · doi:10.1016/bs.ache.2016.09.002 · Cited by 137
Thermal decomposition products of polypropylene
Tsuchiya, Y., & Sumi, K. (1969) · Journal of Polymer Science Part A-1 Polymer Chemistry · doi:10.1002/pol.1969.150070704 · Cited by 136
Continuous kinetics for thermal degradation of polymer in solution
Wang, M., Smith, J. M., & McCoy, B. J. (1995) · AIChE Journal · doi:10.1002/aic.690410616 · Cited by 135
Somoza-Tornos, A., González-Garay, A., Pozo, C., Graells, M., Espuña, A., & Guillén‐Gosálbez, G. (2020) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.9b04835 · Cited by 135
Thermal degradation of polystyrene and polyethylene. Part III
Jellinek, H. H. G. (1949) · Journal of Polymer Science · doi:10.1002/pol.1949.120040102 · Cited by 134
Investigation of the Kinetics of Pyrolysis of PVC by TG-MS-Analysis
Knümann, R., & Bockhorn, H. (1994) · Combustion Science and Technology · doi:10.1080/00102209408951877 · Cited by 131
Thermal and catalytic decomposition of mixed plastics
Vasile, C., Pakdel, H., Brebu, M. A., Onu, P., Darie, H., & Ciocâlteu, S. (2001) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/s0165-2370(00)00151-0 · Cited by 131
Reduction, detoxification and recycling of solid waste by hydrothermal technology: A review
Zhan, L., Jiang, L., Zhang, Y., Gao, B., & Xu, Z. (2020) · Chemical Engineering Journal · doi:10.1016/j.cej.2020.124651 · Cited by 131
The Depolymerization of Polymethylene and Polyethylene
Wall, L. A., Madorsky, S. L., Brown, D. W., Straus, S., & Simha, R. (1954) · Journal of the American Chemical Society · doi:10.1021/ja01642a017 · Cited by 128
Catalytic and thermal depolymerization of low value post-consumer high density polyethylene plastic
Kunwar, B., Moser, B. R., Chandrasekaran, S. R., Rajagopalan, N., & Sharma, B. K. (2016) · Energy · doi:10.1016/j.energy.2016.06.024 · Cited by 127
Continuous-mixture fragmentation kinetics: particle size reduction and molecular cracking
McCoy, B. J., & Wang, M. (1994) · Chemical Engineering Science · doi:10.1016/0009-2509(94)00172-3 · Cited by 126
Park, S., Seo, D. K., Lee, S. H., Yu, T.-U., & Hwang, J. (2012) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2012.06.009 · Cited by 126
A review of catalysts used in microwave assisted pyrolysis and gasification
State, R., Volceanov, A., Muley, P. D., & Boldor, D. (2019) · Bioresource Technology · doi:10.1016/j.biortech.2019.01.036 · Cited by 126
Wu, F., Pennings, S. C., Tong, C., & Xu, Y. (2019) · The Science of The Total Environment · doi:10.1016/j.scitotenv.2019.134252 · Cited by 126
Moens, E., Smit, K. D., Marien, Y. W., Trigilio, A. D., Steenberge, P. H. M. V., Geem, K. M. V., Dubois, J., & D’hooge, D. (2020) · Polymers · doi:10.3390/polym12081667 · Cited by 126
Self-citationDhahak, A., Hild, G., Rouaud, M., Mauviel, G., & Burklé-Vitzthum, V. (2019) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2019.104664 · Cited by 124
Analysis and inorganic composition of microplastics in commercial Malaysian fish meals
Karbalaei, S., Golieskardi, A., Watt, D. U., Boiret, M., Hanachi, P., Walker, T. R., & Karami, A. (2019) · Marine Pollution Bulletin · doi:10.1016/j.marpolbul.2019.110687 · Cited by 123
Gai, C., Zhang, Y., Chen, W., Zhang, P., & Dong, Y. (2014) · RSC Advances · doi:10.1039/c3ra46607h · Cited by 122
Polyethylene conversion in supercritical water
Watanabe, M., Hirakoso, H., Sawamoto, S., Adschiri, T., & Arai, K. (1998) · The Journal of Supercritical Fluids · doi:10.1016/s0896-8446(98)00058-8 · Cited by 121
Kinetic Study of Polyolefin Pyrolysis in a Conical Spouted Bed Reactor
Aguado, R., Olazar, M., Gaisán, B., Prieto, R., & Bilbao, J. (2002) · Industrial & Engineering Chemistry Research · doi:10.1021/ie0201260 · Cited by 121
Chemical Recycling of Polymer Materials
Sasse, F., & Emig, G. (1998) · Chemical Engineering & Technology · Cited by 121
Continuous Polyolefin Cracking on an HZSM-5 Zeolite Catalyst in a Conical Spouted Bed Reactor
Elordi, G., Olazar, M., López, G., Artetxe, M., & Bilbao, J. (2011) · Industrial & Engineering Chemistry Research · doi:10.1021/ie2002999 · Cited by 121
Catalytic flash pyrolysis of HDPE in a fluidized bed reactor for recovery of fuel-like hydrocarbons
Hernández, M. D. R., García, A. N. J., & Marcilla, A. F. (2006) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2006.03.009 · Cited by 120
D’hooge, D., Steenberge, P. H. M. V., Derboven, P., Reyniers, M., & Marin, G. B. (2015) · Polymer Chemistry · doi:10.1039/c5py01069a · Cited by 119
Self-citationScreening of common synthetic polymers for depolymerization by subcritical hydrothermal liquefaction
dos Passos, J. S., Glasius, M., & Biller, P. (2020) · Process Safety and Environmental Protection · doi:10.1016/j.psep.2020.04.040 · Cited by 119
Ding, W., Liang, J., & Anderson, L. L. (1997) · Fuel Processing Technology · doi:10.1016/s0378-3820(96)01080-6 · Cited by 118
The Population Balance as a Tool for Understanding Particle Rate Processes
Hounslow, M. J. (1998) · KONA Powder and Particle Journal · doi:10.14356/kona.1998021 · Cited by 118
Enzymatic recovery of polyester building blocks from polymer blends
Gamerith, C., Zartl, B., Pellis, A., Guillamot, F., Marty, A., Acero, E. H., & Guebitz, G. M. (2017) · Process Biochemistry · doi:10.1016/j.procbio.2017.01.004 · Cited by 118
Steenberge, P. H. M. V., D’hooge, D., Reyniers, M., & Marin, G. B. (2014) · Chemical Engineering Science · doi:10.1016/j.ces.2014.01.019 · Cited by 117
Self-citationKinetic modeling of the thermal degradation of polyethylene and polystyrene mixtures
Faravelli, T., Bozzano, G., Colombo, M., Ranzi, E., & Dente, M. (2003) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/s0165-2370(03)00058-5 · Cited by 116
Self-citationFluidized-bed incineration of waste materials
Saxena, S. C., & Jotshi, C. K. (1994) · Progress in Energy and Combustion Science · doi:10.1016/0360-1285(94)90012-4 · Cited by 116
Synthetic Polyester-Hydrolyzing Enzymes From Thermophilic Actinomycetes
Wei, R., Oeser, T., & Zimmermann, W. (2014) · Advances in applied microbiology · doi:10.1016/b978-0-12-800259-9.00007-x · Cited by 116
Recycling of waste plastics into fuels. LDPE conversion in FCC
Passamonti, F. J., & Sedran, U. (2012) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2012.06.020 · Cited by 115
Molecular Weight Effect on the Dynamics of Polystyrene Degradation
Madras, G., Chung, G.-Y., Smith, J. M., & McCoy, B. J. (1997) · Industrial & Engineering Chemistry Research · doi:10.1021/ie9607513 · Cited by 115
Gas product distribution from polyethylene pyrolysis
Faravelli, T., Bozzano, G., Scassa, C., Perego, M., Fabini, S., Ranzi, E., & Dente, M. (1999) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/s0165-2370(99)00032-7 · Cited by 114
Self-citationPoutsma, M. L. (2003) · Macromolecules · doi:10.1021/ma0303768 · Cited by 114
Detailed kinetic mechanism of gas-phase reactions of volatiles released from biomass pyrolysis
Debiagi, P. E. A., Gentile, G., Pelucchi, M., Frassoldati, A., Cuoci, A., Faravelli, T., & Ranzi, E. (2016) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2016.06.015 · Cited by 114
Self-citationDegradation kinetics of polymers in solution: Dynamics of molecular weight distributions
McCoy, B. J., & Madras, G. (1997) · AIChE Journal · doi:10.1002/aic.690430325 · Cited by 110
Effect of diaminotoluene on the decomposition of polyurethane foam waste in superheated water
Dai, Z., Hatano, B., Kadokawa, J., & Tagaya, H. (2002) · Polymer Degradation and Stability · doi:10.1016/s0141-3910(02)00010-1 · Cited by 108
Olivine as a tar removal catalyst during fluidized bed gasification of plastic waste
Mastellone, M. L., & Arena, U. (2008) · AIChE Journal · doi:10.1002/aic.11497 · Cited by 108
Navarro, M. V., López, J. M., Veses, A., Callén, M. S., & García, T. (2018) · Energy · doi:10.1016/j.energy.2018.09.133 · Cited by 108
Bio-oil Production from Biomass: Steps toward Demonstration
Solantausta, Y., Oasmaa, A., Sipilä, K., Lindfors, C., Lehto, J., Autio, J., Jokela, P., Alin, J., & Heiskanen, J. (2011) · Energy & Fuels · doi:10.1021/ef201109t · Cited by 106
Life-cycle analysis of fuels from post-use non-recycled plastics
Benavides, P. T., Sun, P., Han, J., Dunn, J. B., & Wang, M. (2017) · Fuel · doi:10.1016/j.fuel.2017.04.070 · Cited by 106
Banu, J. R., Sharmila, V. G., Ushani, U., Amudha, V., & Kumar, G. (2020) · The Science of The Total Environment · doi:10.1016/j.scitotenv.2020.137287 · Cited by 104
Thermal degradation mechanisms of nylon 6 deduced from kinetic studies by pyrolysis-g.c.
Lehrle, R. S., Parsons, I. W., & Rollinson, M. (2000) · Polymer Degradation and Stability · doi:10.1016/s0141-3910(99)00112-3 · Cited by 102
Modification of mechanical properties of recycled polypropylene from post-consumer containers
Brachet, P., Høydal, L. T., Hinrichsen, E. L., & Melum, F. V. (2008) · Waste Management · doi:10.1016/j.wasman.2007.10.021 · Cited by 102
Investigation on degradation of polyethylene to oils in supercritical water
Su, X., Zhao, Y., Zhang, R., & Bi, J. (2004) · Fuel Processing Technology · doi:10.1016/j.fuproc.2003.11.044 · Cited by 101
Chemical recycling of plastic waste: Bitumen, solvents, and polystyrene from pyrolysis oil
Baena-González, J., Santamaria‐Echart, A., Aguirre, J. L., & González, S. (2020) · Waste Management · doi:10.1016/j.wasman.2020.08.035 · Cited by 101
Karayannidis, G. P., Nikolaidis, A. K., Sideridou, I. D., Bikiaris, D. Ν., & Achilias, D. S. (2006) · Macromolecular Materials and Engineering · doi:10.1002/mame.200600243 · Cited by 100
Modeling particle size distribution in emulsion polymerization reactors
Vale, H. M., & McKenna, T. F. L. (2005) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2005.06.006 · Cited by 100
Recycling poly-(methyl methacrylate) by pyrolysis in a conical spouted bed reactor
López, G., Artetxe, M., Amutio, M., Elordi, G., Aguado, R., Olazar, M., & Bilbao, J. (2010) · Chemical Engineering and Processing - Process Intensification · doi:10.1016/j.cep.2010.08.002 · Cited by 99
Lin, H.-T., Huang, M., Luo, J.-W., Lin, L.-H., Lee, C., & Ou, K. (2010) · Fuel Processing Technology · doi:10.1016/j.fuproc.2010.03.016 · Cited by 99
Plastic production, waste and legislation
Crawford, C. B., & Quinn, B. (2016) · Elsevier eBooks · doi:10.1016/b978-0-12-809406-8.00003-7 · Cited by 99
Partial oxidation of n-hexadecane and polyethylene in supercritical water
Watanabe, M., Mochiduki, M., Sawamoto, S., Adschiri, T., & Arai, K. (2001) · The Journal of Supercritical Fluids · doi:10.1016/s0896-8446(01)00070-5 · Cited by 97
619. The thermal degradation of ethylene polymers
Oakes, W. G., & Richards, R. B. (1949) · Journal of the Chemical Society (Resumed) · doi:10.1039/jr9490002929 · Cited by 96
Microplastics, standardisation and spatial distribution
Crawford, C. B., & Quinn, B. (2016) · Elsevier eBooks · doi:10.1016/b978-0-12-809406-8.00005-0 · Cited by 96
Schirmer, J., Kim, J., & Klemm, E. (2001) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/s0165-2370(00)00197-2 · Cited by 95
Chemical recycling of mixed plastics of pyrolysis
Kaminsky, W. (1995) · Advances in Polymer Technology · doi:10.1002/adv.1995.060140407 · Cited by 95
Rodríguez, E., Gutiérrez, A., Palos, R., Vela, F. J., Arandes, J. M., & Bilbao, J. (2019) · Waste Management · doi:10.1016/j.wasman.2019.05.005 · Cited by 95
Zhao, X., Xia, Y., Zhan, L., Xie, B., Gao, B., & Wang, J. (2018) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.8b05147 · Cited by 94
Renewable, Degradable, and Chemically Recyclable Cross-Linked Elastomers
Brutman, J. P., De Hoe, G. X., Schneiderman, D. K., Le, T. N., & Hillmyer, M. A. (2016) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.6b02931 · Cited by 92
Biodegradable and Biobased Polymers
Jiang, L., & Zhang, J. (2016) · Elsevier eBooks · doi:10.1016/b978-0-323-39040-8.00007-9 · Cited by 92
Detailed kinetic modeling of the thermal degradation of vinyl polymers
Marongiu, A., Faravelli, T., & Ranzi, E. (2006) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2006.09.008 · Cited by 92
Self-citationMicrobial biotechnology addressing the plastic waste disaster
Narančić, T., & O’Connor, K. E. (2017) · Microbial Biotechnology · doi:10.1111/1751-7915.12775 · Cited by 91
To be, or not to be biodegradable… that is the question for the bio‐based plastics
Prieto, M. A. (2016) · Microbial Biotechnology · doi:10.1111/1751-7915.12393 · Cited by 90
A review on conversion techniques of liquid fuel from waste plastic materials
Chandran, M., Senthilkumar, T., & Chandrasekar, M. (2017) · International Journal of Energy Research · doi:10.1002/er.3720 · Cited by 90
Gasification of coal and PET in fluidized bed reactor
Pohořelý, M., Vosecký, M., HEJDOVA, P., Punčochář, M., Skoblia, S., Staf, M., Vošta, J., Koutský, B., & Svoboda, K. (2006) · Fuel · doi:10.1016/j.fuel.2006.04.022 · Cited by 89
Molecular weight and pyrolysis products distribution of polymers
Audisio, G., & Bertini, F. (1992) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/0165-2370(92)80005-7 · Cited by 88
Shi, X., Li, H., Song, Z., Zhang, X., & Liu, G. (2017) · Fuel · doi:10.1016/j.fuel.2017.03.073 · Cited by 88
Solomon, O., & Palanisami, T. (2016) · Journal of Pollution Effects & Control · doi:10.4172/2375-4397.1000161 · Cited by 86
Advances in clean hydrocarbon fuel processing
Khan, M. R. (2011) · Woodhead Publishing Limited eBooks · doi:10.1533/9780857093783 · Cited by 86
Jones, G. O., Yuen, A., Wojtecki, R. J., Hedrick, J. L., & García, J. M. (2016) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.1600924113 · Cited by 85
Wong, H., & Broadbelt, L. J. (2001) · Industrial & Engineering Chemistry Research · doi:10.1021/ie010171s · Cited by 85
Measuring biomass fast pyrolysis kinetics: State of the art
SriBala, G., Carstensen, H., Geem, K. M. V., & Marin, G. B. (2018) · Wiley Interdisciplinary Reviews Energy and Environment · doi:10.1002/wene.326 · Cited by 84
Charitopoulou, M. A., Kalogiannis, K. G., Lappas, A. A., & Achilias, D. S. (2020) · Environmental Science and Pollution Research · doi:10.1007/s11356-020-09932-5 · Cited by 83
Converting Biomass and Waste Plastic to Solid Fuel Briquettes
Zannikos, F., Kalligeros, S. S., Anastopoulos, G., & Lois, E. (2012) · Journal of Renewable Energy · doi:10.1155/2013/360368 · Cited by 82
Mechanistic modelling of fluidized bed drying processes of wet porous granules: A review
Mortier, S. T. F. C., Beer, T. D., Gernaey, K. V., Remon, J. P., Vervaet, C., & Ingmar Nopens, A. (2011) · European Journal of Pharmaceutics and Biopharmaceutics · doi:10.1016/j.ejpb.2011.05.013 · Cited by 82
Recycling of plastic waste into fuel by pyrolysis - a review
Jha, K. K., & Kannan, T. T. M. (2020) · Materials Today Proceedings · doi:10.1016/j.matpr.2020.10.181 · Cited by 82
Biller, P., Johannsen, I., dos Passos, J. S., & Ottosen, L. D. M. (2017) · Water Research · doi:10.1016/j.watres.2017.11.048 · Cited by 81
Sustainable Food Waste-To-energy Systems
Trabold, T., & Babbitt, C. W. (2018) · Elsevier eBooks · doi:10.1016/c2016-0-00715-5 · Cited by 81
Catalytic depolymerization of polyethylene terephthalate in hot compressed water
Liu, Y., Wang, M., & Pan, Z. (2011) · The Journal of Supercritical Fluids · doi:10.1016/j.supflu.2011.11.001 · Cited by 80
Catalytic efficiency of some novel nanostructured heterogeneous solid catalysts in pyrolysis of HDPE
Ahmad, I. K., Khan, M. I., Ishaq, M., Khan, H., Gul, K., & Ahmad, W. (2013) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2013.09.009 · Cited by 80
Wall, L. A., & Straus, S. (1960) · Journal of Polymer Science · doi:10.1002/pol.1960.1204414404 · Cited by 79
Silva, A. B., da Costa, M. F., & Duarte, A. C. (2017) · Current Opinion in Environmental Science & Health · doi:10.1016/j.coesh.2017.10.005 · Cited by 79
Smit, K. D., Marien, Y. W., Geem, K. M. V., Steenberge, P. H. M. V., & D’hooge, D. (2020) · Reaction Chemistry & Engineering · doi:10.1039/d0re00266f · Cited by 77
Self-citationRenewable energy from solid waste: life cycle analysis and social welfare
Ramos, A., & Rouboa, A. I. (2020) · Environmental Impact Assessment Review · doi:10.1016/j.eiar.2020.106469 · Cited by 77
Method for Efficient Recovery of High-Purity Polycarbonates from Electronic Waste
Weeden, G. S., Soepriatna, N. H., & Wang, N. L. (2015) · Environmental Science & Technology · doi:10.1021/es5055786 · Cited by 76
Plehiers, P. P., Symoens, S. H., Amghizar, I., Marin, G. B., Stevens, C. V., & Geem, K. M. V. (2019) · Engineering · doi:10.1016/j.eng.2019.02.013 · Cited by 75
Kinetic Modelling of Pyrolysis Processes in Gas and Condensed Phase
Dente, M., Bozzano, G., Faravelli, T., Marongiu, A., Pierucci, S., & Ranzi, E. (2007) · Advances in chemical engineering · doi:10.1016/s0065-2377(07)32002-4 · Cited by 74
Self-citationMass spectrometric investigation of the thermal decomposition of polymers
Wall, L. A. (1948) · Journal of research of the National Bureau of Standards · doi:10.6028/jres.041.033 · Cited by 73
Pyrolysis, Gasification, and Combustion of Solid Fuels
Ranzi, E., Faravelli, T., & Manenti, F. (2016) · Advances in chemical engineering · doi:10.1016/bs.ache.2016.09.001 · Cited by 72
Self-citationThe resource utilization of ABS plastic waste with subcritical and supercritical water treatment
Liu, Y., Fan, C., Zhang, H., Zou, J. X., Zhou, F., & Jin, H. (2018) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2018.08.012 · Cited by 72
Bockhorn, H., Hornung, A., Hornung, U., & Jakobströer, P. (1999) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/s0165-2370(98)00130-2 · Cited by 70
Netherlands To Aid Central, Eastern Europe in Halting Pollution Effects
O'SULLIVAN, D. A. (1991) · Chemical & Engineering News · doi:10.1021/cen-v069n010.p026 · Cited by 70
Gigmès, D., Steenberge, P. H. M. V., Siri, D., D’hooge, D., Guillaneuf, Y., & Lefay, C. (2018) · Macromolecular Rapid Communications · doi:10.1002/marc.201800193 · Cited by 70
Self-citationPaabo, M., & Levin, B. C. (1987) · Fire and Materials · doi:10.1002/fam.810110203 · Cited by 69
BIODEGRADATION OF LOW DENSITY POLYETHYLENE BY MICRO- ORGANISMS FROM GARBAGE SOIL
Deepika, S., & Madhuri, R. J. (2015) · Journal of Experimental Biology and Agricultural Sciences · Cited by 69
Anthony, G. M. (1999) · Polymer Degradation and Stability · doi:10.1016/s0141-3910(98)00129-3 · Cited by 68
Biodegradability of degradable plastic waste
Agamuthu, P., & Faizura, P. N. (2005) · Waste Management & Research The Journal for a Sustainable Circular Economy · doi:10.1177/0734242x05051045 · Cited by 68
Time evolution to similarity solutions for polymer degradation
Madras, G., & McCoy, B. J. (1998) · AIChE Journal · doi:10.1002/aic.690440313 · Cited by 66
Thermal degradation kinetics of polystyrene in solution
Madras, G., Smith, J. M., & McCoy, B. J. (1997) · Polymer Degradation and Stability · doi:10.1016/s0141-3910(97)00036-0 · Cited by 64
Goff, M., WARD, P., & OCONNOR, K. (2007) · Journal of Biotechnology · doi:10.1016/j.jbiotec.2007.03.016 · Cited by 64
Comparison between the Pyrolysis of Two Types of Polyethylenes in a Fluidized Bed Reactor
Conesa, J. A., Font, R., & Marcilla, A. F. (1997) · Energy & Fuels · doi:10.1021/ef960098w · Cited by 63
Recycling techniques of polyolefins from plastic wastes
(2013) · Global NEST Journal · doi:10.30955/gnj.000468 · Cited by 63
Hydrocracking of a plastic mixture over various micro-mesoporous composite zeolites
Munir, D., Abdullah, Piepenbreier, F., & Usman, M. R. (2017) · Powder Technology · doi:10.1016/j.powtec.2017.01.037 · Cited by 63
Madorsky, S. L., Straus, S., Thompson, D., et al. (1949) · Journal of Polymer Science · doi:10.1002/pol.1949.120040510 · Cited by 61
Santos, E., Rijo, B., Lemos, F., & Lemos, M. A. N. D. A. (2019) · Chemical Engineering Journal · doi:10.1016/j.cej.2019.122077 · Cited by 61
Levin, B. C. (1987) · Fire and Materials · doi:10.1002/fam.810110304 · Cited by 59
Michajlov, L., Zugenmaier, P., & Cantow, H. ‐. (1968) · Polymer · doi:10.1016/0032-3861(68)90042-6 · Cited by 59
Modelling of the pyrolysis of high density polyethylene
Mastral, J. F., Berrueco, C., & Ceamanos, J. (2006) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2006.10.018 · Cited by 58
The thermal degradation kinetics of polypropylene: Part I. Molecular weight distribution
Chan, J. H., & Balke, S. T. (1997) · Polymer Degradation and Stability · doi:10.1016/s0141-3910(96)00158-9 · Cited by 58
Two-step pyrolysis for waste HDPE valorization
Rodríguez-Luna, L., Martínez, D. B., & Valenzuela, E. (2020) · Process Safety and Environmental Protection · doi:10.1016/j.psep.2020.11.038 · Cited by 58
Lena, J.-B., & van Herk, A. M. (2019) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.9b02375 · Cited by 57
Fluidized Bed Pyrolysis of Plastic Wastes
Arena, U., & Mastellone, M. L. (2006) · doi:10.1002/0470021543.ch16 · Cited by 56
Pyrolysis of polystyrene in a batch-type stirred vessel
Kim, Y. S., Hwang, G. C., Bae, S. Y., Yi, S., Moon, S. K., & Kumazawa, H. (1999) · Korean Journal of Chemical Engineering · doi:10.1007/bf02706830 · Cited by 56
Lédé, J. (1994) · Biomass and Bioenergy · doi:10.1016/0961-9534(94)00046-v · Cited by 56
Investigation on degradation of polyethylene to oil in a continuous supercritical water reactor
Zhang, H., Su, X., Sun, D., Zhang, R., & Bi, J. (2007) · Journal of Fuel Chemistry and Technology · doi:10.1016/s1872-5813(07)60030-9 · Cited by 56
Park, K.-B., Oh, S., Güzelçiftçi, B., & Kim, J.-S. (2018) · Energy · doi:10.1016/j.energy.2018.05.182 · Cited by 56
Polyethylene Pyrolysis: Theory and Experiments for Molecular-Weight-Distribution Kinetics
Sezgi, N. A., Cha, W. S., Smith, J. M., et al. (1998) · Industrial & Engineering Chemistry Research · doi:10.1021/ie980106r · Cited by 54
High-temperature liquefaction of waste plastics
Ramdoss, P. K., & Tarrer, A. R. (1998) · Fuel · doi:10.1016/s0016-2361(97)00193-2 · Cited by 54
Thermal degradation of high density polyethylene in a reactive extruder
Wallis, M. D., & Bhatia, S. K. (2007) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2007.06.002 · Cited by 54
Theoretical prediction of product distribution of the pyrolysis of high density polyethylene
Mastral, J. F., Berrueco, C., & Ceamanos, J. (2007) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2006.07.009 · Cited by 53
Some aspects of depolymerization kinetics
Simha, R., & Wall, L. A. (1951) · Journal of Polymer Science · doi:10.1002/pol.1951.120060107 · Cited by 52
Steenberge, P. H. M. V., Vandenbergh, J., Reyniers, M., Junkers, T., D’hooge, D., & Marin, G. B. (2017) · Macromolecules · doi:10.1021/acs.macromol.7b00333 · Cited by 50
Self-citationGreen energy: Hydroprocessing waste polypropylene to produce transport fuel
Mangesh, V. L., Tamizhdurai, P., Krishnan, P. S., Narayanan, S., Umasankar, S., Padmanabhan, S., & Shanthi, K. (2020) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2020.124200 · Cited by 50
Continuous‐mixture kinetics and equilibrium for reversible oligomerization reactions
McCoy, B. J. (1993) · AIChE Journal · doi:10.1002/aic.690391110 · Cited by 49
Effects of Chain Length on the Rates of C−C Bond Dissociation in Linear Alkanes and Polyethylene
Knyazev, V. D. (2007) · The Journal of Physical Chemistry A · doi:10.1021/jp066419e · Cited by 47
Navarro, M. V., Martínez, J. D., Murillo, R., García, T., López, J. M., Callén, M. S., & Mastral, A. M. (2012) · Fuel Processing Technology · doi:10.1016/j.fuproc.2011.12.031 · Cited by 45
Gulab, H., Jan, M. R., Shah, J., & Manos, G. (2010) · Journal of Environmental Science and Health Part A · doi:10.1080/10934521003709206 · Cited by 44
Cited by
Kumar, R., Verma, A., Shome, A., Sinha, R., Sinha, S., Jha, P. K., Kumar, R., Kumar, P., Shubham, Das, S., et al. (2021) · Sustainability · doi:10.3390/su13179963 · Cited by 1,111
The world of plastic waste: A review
Nayanathara Thathsarani Pilapitiya, P. G. C., & Ratnayake, A. S. (2024) · Cleaner Materials · doi:10.1016/j.clema.2024.100220 · Cited by 1,034
Managing Plastic Waste─Sorting, Recycling, Disposal, and Product Redesign
Lange, J.-P. (2021) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.1c05013 · Cited by 637
Expanding plastics recycling technologies: chemical aspects, technology status and challenges
Li, H., Aguirre-Villegas, H. A., Allen, R. D., Bai, X., Benson, C. H., Beckham, G. T., Bradshaw, S. L., Brown, J. L., Brown, R. C., Cecon, V. S., et al. (2022) · Green Chemistry · doi:10.1039/d2gc02588d · Cited by 616
Pyrolysis technology for plastic waste recycling: A state-of-the-art review
Dai, L., Zhou, N., Lv, Y., Cheng, Y., Wang, Y., Liu, Y., Cobb, K., Chen, P., Lei, H., & Ruan, R. (2022) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2022.101021 · Cited by 485
Metadata
- Authors
- Dogu, O., Pelucchi, M., Van de Vijver, R., Van Steenberge, P. H. M., D'hooge, D. R., Cuoci, A., Mehl, M., Frassoldati, A., Faravelli, T., & Van Geem, K. M.
- Venue
- Progress in Energy and Combustion Science
- Publisher
- Elsevier BV
- Published
- 2021-05
- Volume
- 84
- Pages
- 100901
- ISSN
- 0360-1285 (ISSN-L)
- OpenAlex
- W3129319549
- Cited by
- 698
- References
- 431
- FWCI
- 30.80
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.