Solid-state cold spraying of Ti and its alloys: A literature review
The DOI matches its Crossref record; 102 of the 102 references it cites were found in a registry or an index.
Abstract
Abstract Compared to conventional high temperature processes, e.g. arc additive manufacturing, thermal spraying and laser/electron-beam cladding/additive manufacturing, coatings of Ti and its alloys with cold spraying (CS) are increasingly attracting attention from researchers and industries, because of the low temperature and high velocity characteristics of sprayed particles, which strictly restrict the oxidation of the sprayed powder and bring about prominent metallurgical benefits. However, coatings of Ti and its alloys by CS have been found limited industrial applications compared to other materials (e.g. Cu and Al), partly due to the special particle deposition behavior of Ti and its alloys and the lack of comprehensive knowledge of its control. This review therefore focuses on the deposition characteristics of Ti and its alloys during CS in an effort to shed light on them and expand their applications. The first part presents a brief introduction of CS and the basic characteristics of Ti and its alloys coatings by CS. The second part describes the effects of CS process parameters on the deposition characteristics of Ti and its alloys. The third part discusses the bonding mechanisms of Ti and its alloy particles during CS. The fourth part discusses the strengthening methods such as in-situ shot peening and laser-assisted CS. The coating properties can also be improved with post-spray treatment, such as heat treatment, laser treatment, hot rolling, hot isostatic pressing and friction stir processing. In addition, further applications are suggested, such as protective coatings, biocompatible coatings, and additive manufacturing. Finally, the summary and prospects for the deposition of Ti and its alloys are presented.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Bonding mechanism in cold gas spraying
Assadi, H., Gärtner, F., Stoltenhoff, T., & Kreye, H. (2003) · Acta Materialia · doi:10.1016/s1359-6454(03)00274-x · Cited by 1,811
Metal Additive Manufacturing: A Review of Mechanical Properties
Lewandowski, J. J., & Seifi, M. (2016) · Annual Review of Materials Research · doi:10.1146/annurev-matsci-070115-032024 · Cited by 1,722
Xu, W., Brandt, M., Sun, S., Elambasseril, J., Liu, Q., Latham, K., Xia, K., & Qian, M. (2015) · Acta Materialia · doi:10.1016/j.actamat.2014.11.028 · Cited by 1,245
Development of a generalized parameter window for cold spray deposition
Schmidt, T., Gärtner, F., Assadi, H., & Kreye, H. (2006) · Acta Materialia · doi:10.1016/j.actamat.2005.10.005 · Cited by 1,183
Cold spraying – A materials perspective
Assadi, H., Kreye, H., Gärtner, F., & Klassen, T. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.06.034 · Cited by 946
Cold spray coating: review of material systems and future perspectives
Moridi, A., Hassani-Gangaraj, S. M., Guagliano, M., & Dao, M. (2014) · Surface Engineering · doi:10.1179/1743294414y.0000000270 · Cited by 754
From Particle Acceleration to Impact and Bonding in Cold Spraying
Schmidt, T., Assadi, H., Gärtner, F., Richter, H., Stoltenhoff, T., Kreye, H., & Klassen, T. (2009) · Journal of Thermal Spray Technology · doi:10.1007/s11666-009-9357-7 · Cited by 638
Cold spray additive manufacturing and repair: Fundamentals and applications
Yin, S., Cavaliere, P., Aldwell, B., Jenkins, R., Liao, H., Li, W., & Lupoi, R. (2018) · Additive Manufacturing · doi:10.1016/j.addma.2018.04.017 · Cited by 599
Self-citationAn Analysis of the Cold Spray Process and Its Coatings
Stoltenhoff, T., Kreye, H., & Richter, H. J. (2002) · Journal of Thermal Spray Technology · doi:10.1361/105996302770348682 · Cited by 583
Papyrin, A. N. (2001) · Cited by 562
Grujicic, M., Saylor, J. R., Beasley, D. E., DeRosset, W. S., & Helfritch, D. (2003) · Applied Surface Science · doi:10.1016/s0169-4332(03)00643-3 · Cited by 512
Bonding Mechanisms in Cold Spraying: The Contributions of Metallurgical and Mechanical Components
Hussain, T., McCartney, D. G., Shipway, P. H., & Zhang, D. (2009) · Journal of Thermal Spray Technology · doi:10.1007/s11666-009-9298-1 · Cited by 423
Solid-state additive manufacturing and repairing by cold spraying: A review
Li, W., Yang, K., Yin, S., Yang, X., Xu, Y., & Lupoi, R. (2017) · Journal of Material Science and Technology · doi:10.1016/j.jmst.2017.09.015 · Cited by 414
Self-citationOn Parameter Selection in Cold Spraying
Assadi, H., Schmidt, T., Richter, H., Kliemann, J.-O., Binder, K., Gärtner, F., Klassen, T., & Kreye, H. (2011) · Journal of Thermal Spray Technology · doi:10.1007/s11666-011-9662-9 · Cited by 413
Impact of High Velocity Cold Spray Particles
Dykhuizen, R. C., Smith, M. F., Gilmore, D. L., Neiser, R. A., Jiang, X., & Sampath, S. (1999) · Journal of Thermal Spray Technology · doi:10.1361/105996399770350250 · Cited by 413
Deposition characteristics of titanium coating in cold spraying
Li, C., & Li, W. (2003) · Surface and Coatings Technology · doi:10.1016/s0257-8972(02)00919-2 · Cited by 358
Self-citationAdiabatic shear instability is not necessary for adhesion in cold spray
Hassani-Gangaraj, M., Veysset, D., Champagne, V. K., Nelson, K. A., & Schuh, C. A. (2018) · Acta Materialia · doi:10.1016/j.actamat.2018.07.065 · Cited by 351
Beese, A. M., & Carroll, B. E. (2015) · JOM · doi:10.1007/s11837-015-1759-z · Cited by 343
Bonding features and associated mechanisms in kinetic sprayed titanium coatings
Bae, G., Kumar, S., Yoon, S., Kang, K., Na, H., Kim, H., & Lee, C. (2009) · Acta Materialia · doi:10.1016/j.actamat.2009.07.061 · Cited by 336
Standoff distance and bow shock phenomena in the Cold Spray process
Pattison, J., Celotto, S., Khan, A., & O’Neill, W. D. (2007) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2007.06.065 · Cited by 293
Deposition of FeCoNiCrMn high entropy alloy (HEA) coating via cold spraying
Yin, S., Li, W., Song, B., Yan, X., Kuang, M., Xu, Y., Wen, K., & Lupoi, R. (2019) · Journal of Materials Science & Technology · doi:10.1016/j.jmst.2018.12.015 · Cited by 255
Self-citationCold gas dynamic manufacturing: A non-thermal approach to freeform fabrication
Pattison, J., Celotto, S., Morgan, R., Bray, M. E., & O’Neill, W. (2006) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2006.05.001 · Cited by 229
Chen, C., Xie, Y., Yan, X., Yin, S., FUKANUMA, H., Huang, R., Zhao, R., Wang, J., Ren, Z., Liu, M., et al. (2019) · Additive manufacturing · doi:10.1016/j.addma.2019.03.028 · Cited by 210
Self-citationThe Effect of Deposition Conditions on Adhesion Strength of Ti and Ti6Al4V Cold Spray Splats
Goldbaum, D., Shockley, J. M., Chromik, R. R., Rezaeian, A., Yue, S., Legoux, J.-G., & Irissou, É. (2011) · Journal of Thermal Spray Technology · doi:10.1007/s11666-011-9720-3 · Cited by 199
Residual stress development in cold sprayed Al, Cu and Ti coatings
Suhonen, T., Varis, T., Dosta, S., Torrell, M., & Guilemany, J. M. (2013) · Acta Materialia · doi:10.1016/j.actamat.2013.06.033 · Cited by 184
Effect of Particle Morphology and Size Distribution on Cold-Sprayed Pure Titanium Coatings
Wong, W., Vo, P., Irissou, E., Ryabinin, A. N., Legoux, J.-G., & Yue, S. (2013) · Journal of Thermal Spray Technology · doi:10.1007/s11666-013-9951-6 · Cited by 181
Effect of standoff distance on coating deposition characteristics in cold spraying
Li, W., Zhang, C., Guo, X., Zhang, G., Liao, H., Li, C., & Coddet, C. (2007) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2007.02.005 · Cited by 180
Self-citationThe unique abilities of cold spray deposition
Champagne, V., & Helfritch, D. (2016) · International Materials Reviews · doi:10.1080/09506608.2016.1194948 · Cited by 180
Wei, Y., Li, Y., Zhang, Y., Luo, X., & Li, C. (2018) · Corrosion Science · doi:10.1016/j.corsci.2018.04.018 · Cited by 179
Binder, K., Gottschalk, J., Kollenda, M., Gärtner, F., & Klassen, T. (2011) · Journal of Thermal Spray Technology · doi:10.1007/s11666-010-9557-1 · Cited by 175
Wong, W., Irissou, E., Ryabinin, A. N., Legoux, J.-G., & Yue, S. (2011) · Journal of Thermal Spray Technology · doi:10.1007/s11666-010-9568-y · Cited by 172
Gas Flow, Particle Acceleration, and Heat Transfer in Cold Spray: A review
Yin, S., Meyer, M., Li, W., Liao, H., & Lupoi, R. (2016) · Journal of Thermal Spray Technology · doi:10.1007/s11666-016-0406-8 · Cited by 172
Self-citationLi, W., & Gao, W. (2009) · Applied Surface Science · doi:10.1016/j.apsusc.2009.04.135 · Cited by 171
Self-citationHodder, K. J., Izadi, H., McDonald, A., & Gerlich, A. P. (2012) · Materials Science and Engineering A · doi:10.1016/j.msea.2012.06.066 · Cited by 171
Grain refinement in a single titanium powder particle impacted at high velocity
Kim, K., Watanabe, M., Kawakita, J., & Kuroda, S. (2008) · Scripta Materialia · doi:10.1016/j.scriptamat.2008.06.020 · Cited by 169
The Laser-assisted Cold Spray process and deposit characterisation
Bray, M., Cockburn, A., & O’Neill, W. (2009) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2009.02.135 · Cited by 169
Marrocco, T., McCartney, D. G., Shipway, P. H., & Sturgeon, A. J. (2006) · Journal of Thermal Spray Technology · doi:10.1361/105996306x108219 · Cited by 165
Li, W., Liao, H., Douchy, G., & Coddet, C. (2006) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2006.05.016 · Cited by 164
Self-citationChaudhuri, A., Raghupathy, Y., Srinivasan, D., Suwas, S., & Srivastava, C. (2017) · Acta Materialia · doi:10.1016/j.actamat.2017.02.070 · Cited by 162
Melt-driven erosion in microparticle impact
Hassani, M., Veysset, D. G., Nelson, K. A., & Schuh, C. A. (2018) · Nature Communications · doi:10.1038/s41467-018-07509-y · Cited by 144
Cold Spraying of Titanium: A Review of Bonding Mechanisms, Microstructure and Properties
Hussain, T. (2012) · Key engineering materials · doi:10.4028/www.scientific.net/kem.533.53 · Cited by 140
Li, W., Zhang, C., Guo, X., Li, C., Liao, H., & Coddet, C. (2007) · Applied Surface Science · doi:10.1016/j.apsusc.2007.06.026 · Cited by 139
Self-citationOptimal Design of a Novel Cold Spray Gun Nozzle at a Limited Space
Li, W., & Li, C. (2005) · Journal of Thermal Spray Technology · doi:10.1361/105996305x59404 · Cited by 133
Self-citationMicrostructure of Kinetic Spray Coatings: A Review
Lee, C., & Kim, J. (2015) · Journal of Thermal Spray Technology · doi:10.1007/s11666-015-0223-5 · Cited by 131
Elimination of porosity in directly fabricated titanium via cold gas dynamic spraying
Zahiri, S. H., Antonio, C., & Jahedi, M. Z. (2008) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2008.03.005 · Cited by 130
A Review of Advanced Composite and Nanostructured Coatings by Solid-State Cold Spraying Process
Li, W., Assadi, H., Gärtner, F., & Yin, S. (2018) · Critical reviews in solid state and materials sciences/CRC critical reviews in solid state and materials sciences · doi:10.1080/10408436.2017.1410778 · Cited by 122
Self-citationYang, K., Li, W., Niu, P., Yang, X., & Xu, Y. (2017) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2017.11.132 · Cited by 121
Self-citationLi, W., Zhang, C., Wang, H.-T., Guo, X., Liao, H., Li, C., & Coddet, C. (2006) · Applied Surface Science · doi:10.1016/j.apsusc.2006.07.063 · Cited by 117
Self-citationMechanical and Microstructural Characterization of Cold-Sprayed Ti-6Al-4V After Heat Treatment
Vo, P., Irissou, É., Legoux, J. G., & Yue, S. (2013) · Journal of Thermal Spray Technology · doi:10.1007/s11666-013-9945-4 · Cited by 116
Luo, X., Yao, M.-L., Ma, N., Takahashi, M. K., & Li, C. (2018) · Materials & Design · doi:10.1016/j.matdes.2018.06.024 · Cited by 109
Moridi, A., Hassani-Gangaraj, S. M., Vezzù, S., Trško, L., & Guagliano, M. (2015) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2015.10.063 · Cited by 108
Microstructure and mechanical anisotropy of additively manufactured cold spray copper deposits
Yin, S., Jenkins, R., Yan, X., & Lupoi, R. (2018) · Materials Science and Engineering A · doi:10.1016/j.msea.2018.07.096 · Cited by 107
Self-citationSingle Impact Bonding of Cold Sprayed Ti-6Al-4V Powders on Different Substrates
Vidaller, M. T. V., List, A., Gärtner, F., Klassen, T., Dosta, S., & Guilemany, J. M. (2015) · Journal of Thermal Spray Technology · doi:10.1007/s11666-014-0200-4 · Cited by 106
A perspective review on the bonding mechanisms in cold gas dynamic spray
Viscusi, A., Astarita, A., Gatta, R. D., & Rubino, F. (2018) · Surface Engineering · doi:10.1080/02670844.2018.1551768 · Cited by 95
Peat, T., Galloway, A., Toumpis, A., McNutt, P., & Iqbal, N. (2016) · Applied Surface Science · doi:10.1016/j.apsusc.2016.10.156 · Cited by 94
Tan, A. W., Sun, W. R., Phang, Y. P., Dai, M., Marinescu, I., Dong, Z., & Liu, E. (2017) · Journal of Thermal Spray Technology · doi:10.1007/s11666-017-0619-5 · Cited by 93
‘Cold spray +’ as a new hybrid additive manufacturing technology: a literature review
Li, W., Cao, C., Wang, G., Wang, F., Xu, Y., & Yang, X. (2019) · Science and Technology of Welding & Joining · doi:10.1080/13621718.2019.1603851 · Cited by 92
Self-citationKim, K., Watanabe, M., & Kuroda, S. (2009) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2009.12.001 · Cited by 91
Effect of Spray Angle on Deposition Characteristics in Cold Spraying
Li, C., Li, W.-Y., Wang, Y., & Fukanuma, H. (2003) · Thermal spray · doi:10.31399/asm.cp.itsc2003p0091 · Cited by 88
Self-citationYin, S., Suo, X., Su, J., Guo, Z., Liao, H., & Wang, X. (2013) · Journal of Thermal Spray Technology · doi:10.1007/s11666-013-0039-0 · Cited by 86
Self-citationMainstreaming cold spray – push for applications
Champagne, V. K., & Helfritch, D. J. (2014) · Surface Engineering · doi:10.1179/1743294414y.0000000277 · Cited by 86
Interface melding in cold spray titanium particle impact
King, P. C., Busch, C., Kittel-Sherri, T., Jahedi, M. Z., & Gulizia, S. (2013) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2013.11.039 · Cited by 85
Guo, X., Zhang, G., Li, W., Gao, Y., Liao, H., & Coddet, C. (2008) · Applied Surface Science · doi:10.1016/j.apsusc.2008.10.041 · Cited by 84
Self-citationEason, P. D., Fewkes, J. A., Kennett, S. C., Eden, T. J., Tello, K. E., Kaufman, M. J., & Tiryakioğlu, M. (2011) · Materials Science and Engineering A · doi:10.1016/j.msea.2011.07.012 · Cited by 81
Characterizations and anisotropy of cold-spraying additive-manufactured copper bulk
Yang, K., Li, W., Guo, X., Yang, X., & Xu, Y. (2018) · Journal of Material Science and Technology · doi:10.1016/j.jmst.2018.01.002 · Cited by 81
Self-citationLek, J. Y., Bhowmik, A., Tan, A. W., Sun, W. R., Song, X., Zhai, W., Buenconsejo, P. J. S., Li, F., Liu, E., Lam, Y. M., et al. (2018) · Applied Surface Science · doi:10.1016/j.apsusc.2018.07.175 · Cited by 81
Li, W., Li, C., & Yang, G. (2010) · Applied Surface Science · doi:10.1016/j.apsusc.2010.08.089 · Cited by 80
Self-citationA Method for Characterizing the Degree of Inter-particle Bond Formation in Cold Sprayed Coatings
Price, T. S., Shipway, P. H., McCartney, D. G., Calla, E., & Zhang, D. (2007) · Journal of Thermal Spray Technology · doi:10.1007/s11666-007-9070-3 · Cited by 77
Kim, K., Watanabe, M., Mitsuishi, K., Iakoubovskii, K. V., & Kuroda, S. (2009) · Journal of Physics D Applied Physics · doi:10.1088/0022-3727/42/6/065304 · Cited by 75
Laser-Assisted Cold-Sprayed Corrosion- and Wear-Resistant Coatings: A Review
Olakanmi, E. O., & Doyoyo, M. (2014) · Journal of Thermal Spray Technology · doi:10.1007/s11666-014-0098-x · Cited by 74
Khodabakhshi, F., Marzbanrad, B., Shah, L. H. A., Jahed, H., & Gerlich, A. P. (2017) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2017.10.060 · Cited by 74
Guillem‐Marti, J., Cinca, N., Punset, M., Cano, I. G., Gil, F. J., Guilemany, J. M., & Dosta, S. (2019) · Colloids and Surfaces B Biointerfaces · doi:10.1016/j.colsurfb.2019.04.048 · Cited by 73
Recrystallization of Cold Spray-Fabricated CP Titanium Structures
Zahiri, S. H., Fraser, D., & Jahedi, M. Z. (2008) · Journal of Thermal Spray Technology · doi:10.1007/s11666-008-9212-2 · Cited by 72
Effect of gas temperature on critical velocity and deposition characteristics in kinetic spraying
Lee, J., Shin, S., Kim, H., & Lee, C. (2006) · Applied Surface Science · doi:10.1016/j.apsusc.2006.07.061 · Cited by 68
Influence of Substrate Temperature on Adhesion Strength of Cold-Sprayed Coatings
Watanabe, Y., Yoshida, C., Atsumi, K., Yamada, M., & Fukumoto, M. (2014) · Journal of Thermal Spray Technology · doi:10.1007/s11666-014-0165-3 · Cited by 67
Effect of substrate surface condition on fatigue behavior of cold sprayed Ti6Al4V coatings
Sun, W. R., Tan, A. W., Khun, N. W., Marinescu, I., & Liu, E. (2016) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2016.11.093 · Cited by 67
Christoulis, D. K., Guetta, S., Guipont, V., & Jeandin, M. (2010) · Journal of Thermal Spray Technology · doi:10.1007/s11666-010-9608-7 · Cited by 64
Significant influence of carrier gas temperature during the cold spray process
Yin, S., Suo, X., Liao, H., Guo, Z., & Wang, X. (2014) · Surface Engineering · doi:10.1179/1743294414y.0000000276 · Cited by 62
Self-citationBae, G., Kang, K., Kim, J.-J., & Lee, C. (2010) · Materials Science and Engineering A · doi:10.1016/j.msea.2010.06.037 · Cited by 61
Modified ball bond shear test for determination of adhesion strength of cold spray splats
Chromik, R. R., Goldbaum, D., Shockley, J. M., Yue, S., Irissou, É., Legoux, J.-G., & Randall, N. X. (2010) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2010.07.037 · Cited by 61
Characterization of Cold Spray Titanium Supersonic Jet
Zahiri, S. H., Yang, W., & Jahedi, M. (2009) · Journal of Thermal Spray Technology · doi:10.1007/s11666-008-9278-x · Cited by 61
Microstructure and bonding mechanisms in cold spray coatings
Walker, M. (2018) · Materials Science and Technology · doi:10.1080/02670836.2018.1475444 · Cited by 61
Recent Developments and Potential Applications of Cold Spraying
Gärtner, F., Schmidt, T., Stoltenhoff, T., & Kreye, H. (2006) · Advanced Engineering Materials · doi:10.1002/adem.200600048 · Cited by 59
Khun, N. W., Tan, A. W., Sun, W. R., & Liu, E. (2017) · Journal of Thermal Spray Technology · doi:10.1007/s11666-017-0588-8 · Cited by 57
Peat, T., Galloway, A., Toumpis, A., Steel, R. J., Zhu, W., & Iqbal, N. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.01.099 · Cited by 56
Sharma, M., Eden, T. J., & Golesich, B. (2014) · Journal of Thermal Spray Technology · doi:10.1007/s11666-014-0175-1 · Cited by 55
Goldbaum, D., Chromik, R. R., Brodusch, N., & Gauvin, R. (2015) · Microscopy and Microanalysis · doi:10.1017/s1431927615000240 · Cited by 54
Microstructural Analysis of Cold-Sprayed Ti-6Al-4V at the Micro- and Nano-Scale
Birt, A., Champagne, V. K., Sisson, R. D., & Apelian, D. (2015) · Journal of Thermal Spray Technology · doi:10.1007/s11666-015-0288-1 · Cited by 53
Rafaja, D., Schucknecht, T., Klemm, V., Paul, A., & Berek, H. (2009) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2009.03.054 · Cited by 51
Lupoi, R. (2013) · Surface Engineering · doi:10.1179/1743294413y.0000000214 · Cited by 51
Zhou, H., Li, C., Ji, G., Fu, S., Yang, H., Luo, X., Yang, G., & Li, C. (2018) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2018.07.009 · Cited by 50
Influence of hot isostatic pressing on structure and properties of titanium cold-spray deposits
Petrovskiy, P. V., Sova, A., Doubenskaia, M., & Smurov, I. Y. (2019) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-018-03233-5 · Cited by 50
A cold-gas spray coating process for enhancing titanium
Segall, A. E., Papyrin, A., Conway, J. C., & Shapiro, D. (1998) · JOM · doi:10.1007/s11837-998-0417-0 · Cited by 49
Perton, M., Costil, S., Wong, W., Poirier, D., Irissou, É., Legoux, J. G., Blouin, A., & Yue, S. (2012) · Journal of Thermal Spray Technology · doi:10.1007/s11666-012-9812-8 · Cited by 48
Adhesion strength of titanium particles to alumina substrates: A combined cold spray and LIPIT study
Imbriglio, S. I., Hassani-Gangaraj, M., Veysset, D., Aghasibeig, M., Gauvin, R., Nelson, K. A., Schuh, C. A., & Chromik, R. R. (2019) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2019.01.071 · Cited by 47
Cold Spray Processing of Titanium Powder
Karthikeyan, J., Kay, C. M., Lindeman, J., Lima, R. S., & Berndt, C. C. (2000) · Thermal spray · doi:10.31399/asm.cp.itsc2000p0255 · Cited by 44
Deposition Features of Ti Coating Using Irregular Powders in Cold Spray
Yin, S., He, P., Liao, H., & Wang, X. (2014) · Journal of Thermal Spray Technology · doi:10.1007/s11666-014-0116-z · Cited by 41
Self-citationYin, S. (2018) · Data Archiving and Networked Services (DANS) · doi:10.17632/vy693tgctm.1 · Cited by 35
Self-citationKhodabakhshi, F., Marzbanrad, B., Shah, L. H. A., Jahed, H., & Gerlich, A. P. (2019) · Journal of Thermal Spray Technology · doi:10.1007/s11666-019-00902-z · Cited by 35
Characterization of Cold Spray Titanium Deposits by X-Ray Microscopy and Microtomography
Zahiri, S. H., Mayo, S. C., & Jahedi, M. Z. (2008) · Microscopy and Microanalysis · doi:10.1017/s1431927608080355 · Cited by 26
New perovskite type oxides: NaATiMO6 (A=Ca or Sr; M=Nb or Ta) and their electrical properties
Rajendran, D. N., Nair, K. R., Rao, P. P., Sibi, K. S., Koshy, P., & Vaidyan, V. K. (2007) · Materials Letters · doi:10.1016/j.matlet.2007.06.022 · Cited by 18
Li, Z., Yang, X., Zhang, J., & Shan, A. (2016) · Advanced Engineering Materials · doi:10.1002/adem.201500567 · Cited by 18
Cited by
Progress and perspectives in laser additive manufacturing of key aeroengine materials
Tan, C., Weng, F., Sui, S., Chew, Y., & Bi, G. (2021) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2021.103804 · Cited by 520
Yang, X., Meng, T., Su, Y., Chai, X., Guo, Z., Yin, S., Ma, T., & Li, W. (2024) · Materials Science and Engineering: A · doi:10.1016/j.msea.2023.146024 · Cited by 40
Self-citation
Metadata
- Authors
- Li, W., Cao, C., & Yin, S.
- Venue
- Progress in Materials Science
- Publisher
- Elsevier BV
- Published
- 2020-05
- Volume
- 110
- Pages
- 100633
- ISSN
- 0079-6425 (ISSN-L)
- OpenAlex
- W2995750336
- Cited by
- 257
- References
- 102
- FWCI
- 16.11
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.