Student or educator? Sign up with your school email and get 6 months of Pro free.
CoChat

The DOI matches its Crossref record; 46 of the 46 references it cites were found in a registry or an index; 1 of the 14 sources its claims cite were checked for support.

Metal-Free Synthesis of Tough PLLA- b -PCVL- b -PLLA Triblock Polyester Thermoplastic Elastomers from Mixed Monomers

Open access
Liu, Jingjing, Xu, Jiaxi, Hadjichristidis, Nikos · 2026 · Macromolecules

Abstract

High Resolution Image Download MS PowerPoint Slide Designing thermoplastic elastomers (TPEs) that are simultaneously biodegradable, metal-free, and mechanically robust remains a major challenge. Here, we report a one-pot organocatalytic ring-opening polymerization strategy that converts a mixed feed of ε-caprolactone (CL), δ-valerolactone (VL), and l -lactide (LLA) into high-molecular-weight PLLA- b -PCVL- b -PLLA triblock copolyesters without metal catalysts. By exploiting the intrinsic reactivity differences among the monomers and switching from diphenyl phosphate (DPP) to tert -butyl phosphazene ( t -BuP 2 ), well-defined triblocks with M n up to 300 kg mol –1 and tunable PLLA contents were obtained. The optimized material exhibits an outstanding combination of tensile strength (61 MPa), elongation at break (>2200%), and toughness (653 MJ m –3 ). Small- and wide-angle X-ray scattering analyses, together with in situ tensile scattering measurements, indicate strain-induced structural reorganization and alignment during deformation. These triblocks also show good elastic recovery and high thermal stability ( T d,5% > 350 °C), reprocessability, and enzymatic degradability. This work provides a metal-free, mixed-monomer, one-pot route to high-performance biodegradable triblock polyester elastomers and offers a promising platform for sustainable elastomeric materials.

Overview

CoChat Summary

TL;DR

A metal-free one-pot organocatalytic ring-opening polymerization of a mixed ε-caprolactone/δ-valerolactone/L-lactide feed yields PLLA-b-PCVL-b-PLLA triblock polyester thermoplastic elastomers with high molecular weight and tunable PLLA content. The optimized B2 combines 61 MPa tensile strength, >2200% elongation at break, and 653 MJ m⁻³ toughness, along with thermal stability, reprocessability, and enzymatic degradability.

Key findings

  • Catalyst switching from diphenyl phosphate (DPP) to tert-butyl phosphazene (t-BuP₂) in one pot gives well-defined triblocks: DPP polymerizes CL/VL while LLA remains unreacted; after 120 h CL/VL both reach >95% conversion, then t-BuP₂ polymerizes LLA to 99% in 5 h. SEC Mn reaches up to 302 kg mol⁻¹ (abstract says up to 300 kg mol⁻¹), with dispersities around 1.2–1.3.
  • B2 (12 wt % PLLA, PCL:PVL = 0.53) shows tensile strength 61 ± 4.3 MPa, elongation at break 2262 ± 67%, toughness 653 ± 52 MJ m⁻³, and elastic recovery 86 ± 2% at 100% strain. B3 has higher strength (67 ± 2.7 MPa) but lower elongation (1465 ± 106%) and toughness (465 ± 58 MJ m⁻³).
  • Thermal and morphological data show PCVL Tg ≈ −59 to −57 °C, PLLA Tm 162–171 °C, Td,5% > 350 °C, SAXS domain spacings of 17.5–52.8 nm, and WAXS peaks from both PLLA and PCVL crystalline domains. In situ scattering indicates strain-induced structural reorganization and alignment; B2 reaches true tensile stress of 1.47 GPa, and all triblocks exceed 700 MPa true stress.
  • B2 was extruded and hot-pressed, and reprocessed samples showed only minor mechanical losses. Enzymatic degradation of B2 in lipase A at 45 °C gave nearly 60% weight loss after 40 days, with surface erosion and a pH decrease from neutral to slightly acidic.

Methods

  • Synthesis: ABA triblock copolyesters with isotactic PLLA hard blocks and CL/VL copolymer soft midblocks were prepared by metal-free ring-opening polymerization in toluene (5 M) at 40 °C using 1,4-benzenedimethanol (BDM) as initiator, a mixed CL/VL/LLA feed, and DPP-to-t-BuP₂ catalyst switching; bulk conditions were also noted.
  • Samples: B1–B5 were prepared with PLLA contents from 4 to 21 wt % and varied CL/VL ratios; Mn,SEC ranged from 241 to 302 kg mol⁻¹. Characterization used ¹H/¹³C NMR, DOSY, SEC, DSC, TGA, DMA, WAXS/SAXS, in situ tensile scattering, and tensile/cyclic tensile testing.
  • Property testing: tensile tests used three specimens; processability was tested by twin-screw extrusion and hot pressing; recyclability by remelting/hot pressing and solvent reprocessing; enzymatic degradation of B2 was followed by SEM, ¹H NMR, weight loss, and pH.

Limitations

  • The paper does not state a limitations section.
  • Evident from the text: enzymatic degradation and processability/recyclability demonstrations focus on B2 rather than all B1–B5, and degradation is shown only under lipase A at 45 °C for 40 days, so broader environmental or biological degradation conditions are not established.
  • Evident from the text: biocompatibility is asserted in the introduction, but no biocompatibility assay is reported in the provided text; also the introduction reports optimized tensile strength/elongation as 67 MPa/>2400%, while the abstract, conclusion, and Table 1 give B2 as 61 MPa/2262%, an internal inconsistency.

Model-written summary. Check it against the paper before relying on it.

Integrity signals

Registry

Crossref · 10.1021/acs.macromol.6c00358

Cites

46 of 46 references verified0 citation errors · 0 not checkable

Statistics

Nothing to recompute.

Verification

Claims the paper makes

0 Valid · 3 Not valid · 7 Not checked · 132 Own results and interpretations

83 more claims

Create a free account to see all 142 claims and every source verdict.

See all claims — free account
  • It may state two separate claims as one. 48
  • Probably not a substantial claim. 6

Create a free account to see these claims.

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

Each contradiction between two passages listed here was confirmed by an independent check.

2 of 2

Citations

Cites

Show all 39 references

Metadata

Authors
Liu, J., Xu, J., & Hadjichristidis, N.
Affiliations
King Abdullah University of Science and Technology (SA)
Corresponding author
  • Liu, Jingjing
  • Hadjichristidis, Nikos
Venue
Macromolecules
Published
2026-04-23
Volume
59
Issue
9
Pages
5265-5274
ISSN
  • 0024-9297 (ISSN-L)
  • 1520-5835
OpenAlex
W7155410659
Cited by
0
References
39
FWCI
0.00
Type
journal article
Language
en
Open access
Locations
Macromolecules (publishedVersion, cc-by)
Funders
King Abdullah University of Science and Technology (BAS/1/1342-01-01)
Topics
  • Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
  • Physical Sciences › Materials Science › Polymers and Plastics › Polymer composites and self-healing
  • Physical Sciences › Materials Science › Materials Chemistry › Block Copolymer Self-Assembly
Keywords
thermoplastic elastomers, poly(L-lactic acid), ε-caprolactone, δ-valerolactone, L-lactide, organocatalytic ring-opening polymerization, metal-free polymerization, diphenyl phosphate, enzymatic degradability, biodegradable elastomers, tough elastomers, tensile strength

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

The claim verdicts this report counts are experimental: their accuracy is not yet measured.

A language model drew the claims from the paper on 2026-10-08, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).

A second model labelled each claim on 2026-10-08 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).

Cited sources are checked with a language model’s help (gpt-6-sol).

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Metal-Free Synthesis of Tough PLLA- b -PCVL- b -PLLA Triblock Polyester Thermoplastic Elastomers from Mixed Monomers. https://app.cochat.ai/papers/10.1021/acs.macromol.6c00358
The paper
Liu, J., Xu, J., & Hadjichristidis, N. (2026). Metal-Free Synthesis of Tough PLLA- b -PCVL- b -PLLA Triblock Polyester Thermoplastic Elastomers from Mixed Monomers. Macromolecules. https://doi.org/10.1021/acs.macromol.6c00358

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.