The DOI matches its Crossref record; 46 of the 46 references it cites were found in a registry or an index; 1 of the 14 sources its claims cite were checked for support.
Metal-Free Synthesis of Tough PLLA- b -PCVL- b -PLLA Triblock Polyester Thermoplastic Elastomers from Mixed Monomers
Open accessAbstract
High Resolution Image Download MS PowerPoint Slide Designing thermoplastic elastomers (TPEs) that are simultaneously biodegradable, metal-free, and mechanically robust remains a major challenge. Here, we report a one-pot organocatalytic ring-opening polymerization strategy that converts a mixed feed of ε-caprolactone (CL), δ-valerolactone (VL), and l -lactide (LLA) into high-molecular-weight PLLA- b -PCVL- b -PLLA triblock copolyesters without metal catalysts. By exploiting the intrinsic reactivity differences among the monomers and switching from diphenyl phosphate (DPP) to tert -butyl phosphazene ( t -BuP 2 ), well-defined triblocks with M n up to 300 kg mol –1 and tunable PLLA contents were obtained. The optimized material exhibits an outstanding combination of tensile strength (61 MPa), elongation at break (>2200%), and toughness (653 MJ m –3 ). Small- and wide-angle X-ray scattering analyses, together with in situ tensile scattering measurements, indicate strain-induced structural reorganization and alignment during deformation. These triblocks also show good elastic recovery and high thermal stability ( T d,5% > 350 °C), reprocessability, and enzymatic degradability. This work provides a metal-free, mixed-monomer, one-pot route to high-performance biodegradable triblock polyester elastomers and offers a promising platform for sustainable elastomeric materials.
Overview
CoChat Summary
TL;DR
A metal-free one-pot organocatalytic ring-opening polymerization of a mixed ε-caprolactone/δ-valerolactone/L-lactide feed yields PLLA-b-PCVL-b-PLLA triblock polyester thermoplastic elastomers with high molecular weight and tunable PLLA content. The optimized B2 combines 61 MPa tensile strength, >2200% elongation at break, and 653 MJ m⁻³ toughness, along with thermal stability, reprocessability, and enzymatic degradability.
Key findings
- Catalyst switching from diphenyl phosphate (DPP) to tert-butyl phosphazene (t-BuP₂) in one pot gives well-defined triblocks: DPP polymerizes CL/VL while LLA remains unreacted; after 120 h CL/VL both reach >95% conversion, then t-BuP₂ polymerizes LLA to 99% in 5 h. SEC Mn reaches up to 302 kg mol⁻¹ (abstract says up to 300 kg mol⁻¹), with dispersities around 1.2–1.3.
- B2 (12 wt % PLLA, PCL:PVL = 0.53) shows tensile strength 61 ± 4.3 MPa, elongation at break 2262 ± 67%, toughness 653 ± 52 MJ m⁻³, and elastic recovery 86 ± 2% at 100% strain. B3 has higher strength (67 ± 2.7 MPa) but lower elongation (1465 ± 106%) and toughness (465 ± 58 MJ m⁻³).
- Thermal and morphological data show PCVL Tg ≈ −59 to −57 °C, PLLA Tm 162–171 °C, Td,5% > 350 °C, SAXS domain spacings of 17.5–52.8 nm, and WAXS peaks from both PLLA and PCVL crystalline domains. In situ scattering indicates strain-induced structural reorganization and alignment; B2 reaches true tensile stress of 1.47 GPa, and all triblocks exceed 700 MPa true stress.
- B2 was extruded and hot-pressed, and reprocessed samples showed only minor mechanical losses. Enzymatic degradation of B2 in lipase A at 45 °C gave nearly 60% weight loss after 40 days, with surface erosion and a pH decrease from neutral to slightly acidic.
Methods
- Synthesis: ABA triblock copolyesters with isotactic PLLA hard blocks and CL/VL copolymer soft midblocks were prepared by metal-free ring-opening polymerization in toluene (5 M) at 40 °C using 1,4-benzenedimethanol (BDM) as initiator, a mixed CL/VL/LLA feed, and DPP-to-t-BuP₂ catalyst switching; bulk conditions were also noted.
- Samples: B1–B5 were prepared with PLLA contents from 4 to 21 wt % and varied CL/VL ratios; Mn,SEC ranged from 241 to 302 kg mol⁻¹. Characterization used ¹H/¹³C NMR, DOSY, SEC, DSC, TGA, DMA, WAXS/SAXS, in situ tensile scattering, and tensile/cyclic tensile testing.
- Property testing: tensile tests used three specimens; processability was tested by twin-screw extrusion and hot pressing; recyclability by remelting/hot pressing and solvent reprocessing; enzymatic degradation of B2 was followed by SEM, ¹H NMR, weight loss, and pH.
Limitations
- The paper does not state a limitations section.
- Evident from the text: enzymatic degradation and processability/recyclability demonstrations focus on B2 rather than all B1–B5, and degradation is shown only under lipase A at 45 °C for 40 days, so broader environmental or biological degradation conditions are not established.
- Evident from the text: biocompatibility is asserted in the introduction, but no biocompatibility assay is reported in the provided text; also the introduction reports optimized tensile strength/elongation as 67 MPa/>2400%, while the abstract, conclusion, and Table 1 give B2 as 61 MPa/2262%, an internal inconsistency.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
0 Valid · 3 Not valid · 7 Not checked · 132 Own results and interpretations
At least one cited source doesn’t support this claim or points to a different paper, and none confirmed it — see the verdicts below.
In the paper
“Collectively, these results confirm that the metal-free one-pot synthesis yields triblock copolymers with thermal resistance comparable to those prepared by conventional metal-catalyzed methods.[28][29][30]”
§ Metal-Free Synthesis of Tough PLLA-b-PCVL-b-PLLA Triblock Polyester Thermoplastic Elastomers from Mixed Monomers > 2.2. Thermal and Mechanical Properties
What the sources say
- Disputedcites [28] sourceExperimental — accuracy not yet measured
The Triblock Polyester Synthesis section states that the one-pot procedure uses a Zn(II)/Mg(II) catalyst for both polymerization steps, contrary to the claim that it is metal-free. The Discussion compares the resulting materials with commercial elastomers, not with triblock copolymers made by conventional metal-catalyzed methods. (LLM, conf=0.90)
Checked by a reasoning model — may be wrong.
- Not checked — no full text of the sourcecites [29] source
- Not checked — no full text of the sourcecites [30] source
boosted- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Disputed
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“In the second stage, switching to a strongly organic basic polymerizes LLA and grows semicrystalline PLLA end blocks from both chain ends.”
§ Metal-Free Synthesis of Tough PLLA-b-PCVL-b-PLLA Triblock Polyester Thermoplastic Elastomers from Mixed Monomers > 1. INTRODUCTION
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“This catalyst switchable mixed monomer ROP directly yields sequence-controlled triblocks PLLA-b-PCVL-b-PLLA without metal residues.”
§ Metal-Free Synthesis of Tough PLLA-b-PCVL-b-PLLA Triblock Polyester Thermoplastic Elastomers from Mixed Monomers > 1. INTRODUCTION
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“These materials exhibit strain-induced alignment during stretching and achieve an outstanding combination of tensile strength (67 MPa), elongation at break (>2400%), and toughness (653 MJ m -3 ), placing them among the highperforming degradable polyester elastomers reported to date.”
§ Metal-Free Synthesis of Tough PLLA-b-PCVL-b-PLLA Triblock Polyester Thermoplastic Elastomers from Mixed Monomers > 1. INTRODUCTION
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“These triblocks also show good elastic recovery and high thermal stability (T d,5% > 350 °C), reprocessability, and enzymatic degradability.”
- Also stated in: § 2.1. Metal-Free One-Pot Synthesis of Triblock Copolyesters from the Mixture of Monomers · plain
“All samples exhibited excellent thermal stability, with decomposition temperatures (T d,5% ) exceeding 350 °C (Figure 3B).”
- Also stated in: § 2.2. Thermal and Mechanical Properties · plain
“The 5% weight-loss temperature (T d,5% ) of B1-B5 is above 350 °C, while the maximum degradation temperature (T max ) falls around 410 °C, indicating that decomposition occurs primarily through esterbond scission of the polyester backbone.”
§ Metal-Free Synthesis of Tough PLLA-b-PCVL-b-PLLA Triblock Polyester Thermoplastic Elastomers from Mixed Monomers > Abstract
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Also stated in: § 2.1. Metal-Free One-Pot Synthesis of Triblock Copolyesters from the Mixture of Monomers · plain
83 more claims
Create a free account to see all 142 claims and every source verdict.
- It may state two separate claims as one. 48
- Probably not a substantial claim. 6
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Metal-Free Synthesis of Tough PLLA-b-PCVL-b-PLLA Triblock Polyester Thermoplastic Elastomers from Mixed Monomers > 2.2. Thermal and Mechanical Properties
“The 5% weight-loss temperature (T d,5% ) of B1-B5 is above 350 °C”
§ Metal-Free Synthesis of Tough PLLA-b-PCVL-b-PLLA Triblock Polyester Thermoplastic Elastomers from Mixed Monomers > 3. CONCLUSIONS
“| B3 | 0.53 | 21 | 800/800/400/1 | 302(1.3) | -57 | 36, 171 | 350 | 67 ± 2.7 | 1465 ± 106 | 465 ± 58 | 78 ± 2 |”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Metal-Free Synthesis of Tough PLLA-b-PCVL-b-PLLA Triblock Polyester Thermoplastic Elastomers from Mixed Monomers > 2.2. Thermal and Mechanical Properties
“The storage modulus (E′) shows a sharp decrease near 55 °C, accompanied by a peak in the loss modulus (E″) and tan δ, indicating the glass transition of the soft PCVL phase.”
§ Metal-Free Synthesis of Tough PLLA-b-PCVL-b-PLLA Triblock Polyester Thermoplastic Elastomers from Mixed Monomers > 2.2. Thermal and Mechanical Properties
“All samples exhibit a well-defined glass transition (T g ≈ -59 to -57 °C) assigned to the amorphous PCVL soft segments”
Citations
Cites
The conflicts between strength and toughness
Ritchie, R. O. (2011) · Nature Materials · doi:10.1038/nmat3115 · Cited by 3,989
Sustainable polymers from renewable resources
Zhu, Y., Romain, C., & Williams, C. K. (2016) · Nature · doi:10.1038/nature21001 · Cited by 2,762
50th Anniversary Perspective: There Is a Great Future in Sustainable Polymers
Schneiderman, D. K., & Hillmyer, M. A. (2017) · Macromolecules · doi:10.1021/acs.macromol.7b00293 · Cited by 1,003
Song, Y., Liu, Y., Qi, T., & Li, G. L. (2018) · Angewandte Chemie International Edition · doi:10.1002/anie.201807622 · Cited by 646
Aliphatic Polyester Block Polymers: Renewable, Degradable, and Sustainable
Hillmyer, M. A., & Tolman, W. B. (2014) · Accounts of Chemical Research · doi:10.1021/ar500121d · Cited by 635
Recent Progress in Additive Manufacturing of Fiber Reinforced Polymer Composite
Goh, G. D., Yap, Y. L., Agarwala, S., & Yeong, W. Y. (2019) · Advanced Materials Technologies · doi:10.1002/admt.201800271 · Cited by 621
Stretchable Self-Healing Polymeric Dielectrics Cross-Linked Through Metal–Ligand Coordination
Rao, Y.-L., Chortos, A., Pfattner, R., Lissel, F., Chiu, Y.-C., Feig, V., Xu, J., Kurosawa, T., Gu, X., Wang, C., et al. (2016) · Journal of the American Chemical Society · doi:10.1021/jacs.6b02428 · Cited by 612
Self-citationWang, X., Zhan, S., Lu, Z., Li, J., Yang, X., Qiao, Y., Men, Y., & Sun, J. (2020) · Advanced Materials · doi:10.1002/adma.202005759 · Cited by 575
Elastomeric biomaterials for tissue engineering
Chen, Q., Liang, S., & Thouas, G. A. (2013) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2012.05.003 · Cited by 564
Buntara, T., Noel, S., Phua, P. H., Melián‐Cabrera, I., de Vries, J. G., & Heeres, H. J. (2011) · Angewandte Chemie International Edition · doi:10.1002/anie.201102156 · Cited by 477
50th Anniversary Perspective: Networks and Gels: Soft but Dynamic and Tough
Creton, C. (2017) · Macromolecules · doi:10.1021/acs.macromol.7b01698 · Cited by 463
Synthesis of functionalized biodegradable polyesters
Williams, C. K. (2007) · Chemical Society Reviews · doi:10.1039/b614342n · Cited by 454
Bio-based polyesters: Recent progress and future prospects
Zhang, Q., Song, M., Xu, Y., Wang, W., Wang, Z., & Zhang, L. (2021) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2021.101430 · Cited by 433
Depolymerization within a Circular Plastics System
Clark, R. A., & Shaver, M. P. (2024) · Chemical Reviews · doi:10.1021/acs.chemrev.3c00739 · Cited by 408
Makiguchi, K., Satoh, T., & Kakuchi, T. (2011) · Macromolecules · doi:10.1021/ma200043x · Cited by 338
Zhang, L., Nederberg, F., Messman, J. M., Pratt, R. C., Hedrick, J. L., & Wade, C. G. (2007) · Journal of the American Chemical Society · doi:10.1021/ja074131c · Cited by 249
Sustainable Elastomers from Renewable Biomass
Wang, Z., Yuan, L., & Tang, C. (2017) · Accounts of Chemical Research · doi:10.1021/acs.accounts.7b00209 · Cited by 234
Guo, Z., Lu, X., Wang, X., Li, X., Li, J., & Sun, J. (2023) · Advanced Materials · doi:10.1002/adma.202300286 · Cited by 232
Zheng, Y., & Pan, P. (2020) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2020.101291 · Cited by 229
Strong, Resilient, and Sustainable Aliphatic Polyester Thermoplastic Elastomers
Watts, A., Kurokawa, N., & Hillmyer, M. A. (2017) · Biomacromolecules · doi:10.1021/acs.biomac.7b00283 · Cited by 188
Organic Ring-Opening Polymerization Catalysts: Reactivity Control by Balancing Acidity
Lin, B., & Waymouth, R. M. (2018) · Macromolecules · doi:10.1021/acs.macromol.8b00540 · Cited by 172
Gazeau-Bureau, S., Delcroix, D., Martín-Vaca, B., Bourissou, D., Navarro, C., & Magnet, S. (2008) · Macromolecules · doi:10.1021/ma800626q · Cited by 165
Makiguchi, K., Ogasawara, Y., Kikuchi, S., Satoh, T., & Kakuchi, T. (2013) · Macromolecules · doi:10.1021/ma4000495 · Cited by 165
Fiber‐Reinforced Viscoelastomers Show Extraordinary Crack Resistance That Exceeds Metals
Cui, W., King, D. R., Huang, Y., Chen, L., Sun, T. L., Guo, Y., Saruwatari, Y., Hui, C., Kurokawa, T., & Gong, J. P. (2020) · Advanced Materials · doi:10.1002/adma.201907180 · Cited by 162
Beckingham, B. S., Sanoja, G. E., & Lynd, N. A. (2015) · Macromolecules · doi:10.1021/acs.macromol.5b01631 · Cited by 146
Polylactide–Poly(6-methyl-ε-caprolactone)–Polylactide Thermoplastic Elastomers
Martello, M. T., & Hillmyer, M. A. (2011) · Macromolecules · doi:10.1021/ma201063t · Cited by 137
Lee, S., Lee, K., Kim, Y.-W., & Shin, J. (2015) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.5b00580 · Cited by 110
Buntara, T., Noël, S., Phua, P. H., Melián-Cabrera, I. V., de Vries, J. G., & Heeres, H. J. (2011) · Angewandte Chemie · doi:10.1002/ange.201102156 · Cited by 102
Bio‐Based Elastomers: Design, Properties, and Biomedical Applications
Liu, Q., Lou, P., Sun, Z., Li, D., Ji, H., Xu, Z., Li, L., Xue, J., Wang, R., Wang, Z., et al. (2025) · Advanced Materials · doi:10.1002/adma.202417193 · Cited by 89
Huang, Y., Chang, R., Han, L., Shan, G., Bao, Y., & Pan, P. (2016) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.5b00855 · Cited by 87
Strategies for the synthesis of block copolymers with biodegradable polyester segments
Diaz, C., & Mehrkhodavandi, P. (2021) · Polymer Chemistry · doi:10.1039/d0py01534b · Cited by 74
Watts, A., & Hillmyer, M. A. (2019) · Biomacromolecules · doi:10.1021/acs.biomac.9b00411 · Cited by 59
Zhao, W., Li, C., Yang, X., He, J., Pang, X., Zhang, Y., Men, Y., & Chen, X. (2022) · CCS Chemistry · doi:10.31635/ccschem.021.202100897 · Cited by 53
Gregory, G. L., & Williams, C. K. (2022) · Macromolecules · doi:10.1021/acs.macromol.2c00068 · Cited by 47
Huang, H.-Y., Xie, M., Wang, S.-Q., Huang, Y.-T., Luo, Y.-H., Yu, D.-G., Cai, Z., & Zhu, J.-B. (2025) · Journal of the American Chemical Society · doi:10.1021/jacs.4c17703 · Cited by 33
Miao, X., Han, R., Tian, J., Ma, Y., Müller, A. J., & Li, Z. (2025) · Angewandte Chemie International Edition · doi:10.1002/anie.202417627 · Cited by 27
Song, Y., Liu, Y., Qi, T., & Li, G. L. (2018) · Angewandte Chemie · doi:10.1002/ange.201807622 · Cited by 27
High‐Performance Recyclable Polyester Elastomers Through Transient Strain‐Stiffening
Gao, C., Poon, K. C., Concilio, M., Zinn, T., Gregory, G. L., & Williams, C. K. (2025) · Advanced Materials · doi:10.1002/adma.202416674 · Cited by 26
Controlling the Fluorescence Performance of AIE Polymers by Controlling the Polymer Microstructure
Xu, J., Wang, J., Bakr, O. M., & Hadjichristidis, N. (2023) · Angewandte Chemie International Edition · doi:10.1002/anie.202217418 · Cited by 24
Self-citationBiodegradable Elastomers Enabling Thermoprocessing Below 100 °C
Panja, S., Siehr, A., Sahoo, A., Siegel, R. A., & Shen, W. (2021) · Biomacromolecules · doi:10.1021/acs.biomac.1c01197 · Cited by 16
Dastidar, R. G., Chavarrio, J. E., Jiang, Z., McClelland, D. J., Mavrikakis, M., & Huber, G. W. (2025) · Applied Catalysis B: Environment and Energy · doi:10.1016/j.apcatb.2024.124519 · Cited by 9
Miao, X., Han, R., Tian, J., Ma, Y., Müller, A. J., & Li, Z. (2024) · Angewandte Chemie · doi:10.1002/ange.202417627 · Cited by 3
Controlling the Fluorescence Performance of AIE Polymers by Controlling the Polymer Microstructure
Xu, J., Wang, J., Bakr, O. M., & Hadjichristidis, N. (2023) · Angewandte Chemie · doi:10.1002/ange.202217418 · Cited by 2
Self-citationChemInform Abstract: Synthesis of Functionalized Biodegradable Polyesters
Williams, C. K. (2007) · ChemInform · doi:10.1002/chin.200801236
Correction to Depolymerization within a Circular Plastics System
Clark, R. A., & Shaver, M. P. (2024) · Chemical Reviews · doi:10.1021/acs.chemrev.4c00473
Dastidar, R., Chavarrio, J. E., Jiang, Z., et al. (2024) · doi:10.2139/ssrn.4846205
Metadata
- Authors
- Liu, J., Xu, J., & Hadjichristidis, N.
- Affiliations
- King Abdullah University of Science and Technology (SA)
- Corresponding author
- Liu, Jingjing
- Hadjichristidis, Nikos
- Venue
- Macromolecules
- Publisher
- American Chemical Society (ACS)
- Published
- 2026-04-23
- Volume
- 59
- Issue
- 9
- Pages
- 5265-5274
- ISSN
- 0024-9297 (ISSN-L)
- 1520-5835
- OpenAlex
- W7155410659
- Semantic Scholar
- b9024b956061f2afa7a9a51ab9dfc9bff0c915bb
- Cited by
- 0
- References
- 39
- FWCI
- 0.00
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Locations
- Macromolecules (publishedVersion, cc-by)
- Funders
- King Abdullah University of Science and Technology (BAS/1/1342-01-01)
- Topics
- Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
- Physical Sciences › Materials Science › Polymers and Plastics › Polymer composites and self-healing
- Physical Sciences › Materials Science › Materials Chemistry › Block Copolymer Self-Assembly
- Keywords
- thermoplastic elastomers, poly(L-lactic acid), ε-caprolactone, δ-valerolactone, L-lactide, organocatalytic ring-opening polymerization, metal-free polymerization, diphenyl phosphate, enzymatic degradability, biodegradable elastomers, tough elastomers, tensile strength
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-08, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-08 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.