The DOI matches its Crossref record; 34 of the 34 references it cites were found in a registry or an index.
Best Practices in Using Foam-Type Electrodes for Electrocatalytic Performance Benchmark
Open accessAbstract
Open-pore foam-type electrodes are three-dimensional (3D) materials (typically, Ni, Cu, Fe, and C; images are shown in Figure S1A) with a wide porosity range (70−98%) where their porous cellular structures are interconnected so fluid and gas can pass through. The unique properties of conductive foams, such as high specific surface area and structural rigidity, make them suitable and popular supports on which the active materials are coated or grown. For example, nearly 8% of the water-splitting electrocatalysts reported in 2019 (Figure S1B) involve foamtype electrodes, claiming outstanding electrocatalytic performance and superiority over the others (Figure S2). Electrocatalysts comparable to commercial noble metal catalysts are often found amid the headlines of various journals. Two indicators, overpotential at given current density (often 10 or 100 mA cm−2, denoted as η10 or η100) and Tafel slope (potential required to achieve every current density increment of 10 mA cm−2), are usually employed for catalytic activity evaluation and comparison. However, we believe some oversimplified and overlooked quantitative and experimental issues in using foam-type electrodes have made the electrocatalyst benchmarking physically groundless and often incommensurable, eventually obstructing the understanding and rational design of electrocatalysts. In this Viewpoint, several problems of using foam-type electrodes as electrocatalyst support are discussed, proving some conventional approaches, such as current density normalization, surface area evaluation, and experimental setup, are problematic. (Figure 1) Surface Area Matters. In most reports, the surface area value used for current density (denoted as J) calculation is not defined, which directly impacts overpotential determination. The ideal normalization of current should be performed with the real active surface (RA, denoted as Areal): the number or the area of the active sites that are responsible for Faradaic current transfer during electrocatalysis (or atomic sites that transfer electrons for electrocatalysis). In an ideal situation where non-Faradaic current can be ignored, the normalization of current at any given overpotential to Areal would reflect the charge (Q) input/output per site/unit area every second. However, the determination of the real active surface area is challenging for many systems because it often depends on the applied potential, electrolyte, and the nature of the reaction involved, making it somewhat too complicated to estimate. Instead, two alternatives, geometric area (GA, denoted as AGA) and electrochemically active surface area (ECSA, denoted as AECSA), are often used. The use of GA for current normalization (denoted as JGA) could be traced back to the period when smooth planar electrodes were widely used in the electrochemical community, and it could be calculated based on the dimension of the surface contacting the electrolyte: AGA = 2hl + wl + 2wh (Figure 2A). In most cases, the thickness of the planar electrode is much smaller than its length and height, thus AGA ≈ 2hl. ECSA is generally evaluated based on the double-layer capacitance value (CDL) of the electrode. All surface species that are capable of forming a double-layer structure would contribute to the ECSA. However, the surface sites involved in the non-Faradaic charging−discharging processes do not necessarily participate in the Faradaic processes. Specifically, for a noncatalytic foam electrode (such as carbon foam): AECSA ≫ AGA, Areal = 0 (Figure 2A). For a foam electrode fully coated with a partially catalytic rough layer (Figure 2B), AECSA= AECSA of noncatalytic sites+ AECSA of catalytic sites and AECSA of catalytic sites= Areal, AECSA ≫ AGA, Areal > AGA. Normalizing the Faradaic current with AECSA (denoted as JECSA) will usually produce a smaller value than the real current
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Benchmarking Heterogeneous Electrocatalysts for the Oxygen Evolution Reaction
McCrory, C. C. L., Jung, S., Peters, J. C., & Jaramillo, T. F. (2013) · Journal of the American Chemical Society · doi:10.1021/ja407115p · Cited by 7,026
McCrory, C. C. L., Jung, S., Ferrer, I. M., Chatman, S. M., Peters, J. C., & Jaramillo, T. F. (2015) · Journal of the American Chemical Society · doi:10.1021/ja510442p · Cited by 4,145
Manufacture, characterisation and application of cellular metals and metal foams
Banhart, J. (2001) · Progress in Materials Science · doi:10.1016/s0079-6425(00)00002-5 · Cited by 3,780
Ultrathin metal–organic framework nanosheets for electrocatalytic oxygen evolution
Zhao, S., Wang, Y., Dong, J., He, C.-T., Yin, H., An, P., Zhao, K., Zhang, X., Gao, C., Zhang, L., et al. (2016) · Nature Energy · doi:10.1038/nenergy.2016.184 · Cited by 2,602
Feng, L.-L., Yu, G., Wu, Y., Li, G.-D., Li, H., Sun, Y., Asefa, T., Chen, W., & Zou, X. (2015) · Journal of the American Chemical Society · doi:10.1021/jacs.5b08186 · Cited by 1,783
Dynamic stability of active sites in hydr(oxy)oxides for the oxygen evolution reaction
Chung, D. Y., Lopes, P. P., Farinazzo Bergamo Dias Martins, P., He, H., Kawaguchi, T., Zapol, P., You, H., Tripkovic, D., Strmcnik, D., Zhu, Y., et al. (2020) · Nature Energy · doi:10.1038/s41560-020-0576-y · Cited by 1,011
The Electrocatalysis of Oxygen Evolution on Perovskites
Bockris, J. O., & Otagawa, T. (1984) · Journal of The Electrochemical Society · doi:10.1149/1.2115565 · Cited by 962
The hydrogen evolution reaction: from material to interfacial descriptors
Dubouis, N., & Grimaud, A. (2019) · Chemical Science · doi:10.1039/c9sc03831k · Cited by 962
Yang, Y., Yao, H., Yu, Z., Islam, S. M., He, H., Yuan, M., Yue, Y., Xu, K., Hao, W., Sun, G., et al. (2019) · Journal of the American Chemical Society · doi:10.1021/jacs.9b04492 · Cited by 911
Best Practices for Reporting Electrocatalytic Performance of Nanomaterials
Voiry, D., Chhowalla, M., Gogotsi, Y., Kotov, N. A., Li, Y., Penner, R. M., Schaak, R. E., & Weiss, P. S. (2018) · ACS Nano · doi:10.1021/acsnano.8b07700 · Cited by 865
Sun, S., Zhou, X., Cong, B., Hong, W., & Chen, G. (2020) · ACS Catalysis · doi:10.1021/acscatal.0c01273 · Cited by 806
Peng, S., Gong, F., Li, L., Yu, D., Ji, D., Zhang, T., Hu, Z., Zhang, Z., Chou, S., Du, Y., et al. (2018) · Journal of the American Chemical Society · doi:10.1021/jacs.8b05134 · Cited by 568
Shan, X., Liu, J., Mu, H., Xiao, Y., Mei, B., Liu, W., Lin, G., Jiang, Z., Wen, L., & Jiang, L. (2020) · Angewandte Chemie International Edition · doi:10.1002/anie.201911617 · Cited by 437
Kinetics of hydrogen evolution on nickel electrodes
Lasia, A., & Rami, A. (1990) · Journal of Electroanalytical Chemistry and Interfacial Electrochemistry · doi:10.1016/0022-0728(90)87140-f · Cited by 415
Ultrathin amorphous cobalt–vanadium hydr(oxy)oxide catalysts for the oxygen evolution reaction
Liu, J., Ji, Y., Nai, J., Niu, X., Luo, Y., Guo, L., & Yang, S. (2018) · Energy & Environmental Science · doi:10.1039/c8ee00611c · Cited by 403
Hui, L., Xue, Y., Huang, B., Yu, H., Zhang, C., Zhang, D., Jia, D., Zhao, Y., Li, Y., Liu, H., et al. (2018) · Nature Communications · doi:10.1038/s41467-018-07790-x · Cited by 377
Sun, H., Min, Y., Yang, W., Lian, Y., Lin, L., Feng, K., Deng, Z., Chen, M., Zhong, J., Xu, L., et al. (2019) · ACS Catalysis · doi:10.1021/acscatal.9b02264 · Cited by 323
NiCoMo Hydroxide Nanosheet Arrays Synthesized via Chloride Corrosion for Overall Water Splitting
Hao, S., Chen, L., Yu, C., Yang, B., Li, Z., Hou, Y., Lei, L., & Zhang, X. (2019) · ACS Energy Letters · doi:10.1021/acsenergylett.9b00333 · Cited by 307
Sun, H., Lian, Y., Yang, C., Xiong, L., Qi, P., Mu, Q., Zhao, X., Guo, J., Deng, Z., & Peng, Y. (2018) · Energy & Environmental Science · doi:10.1039/c8ee00934a · Cited by 305
Amorphous Cobalt Vanadium Oxide as a Highly Active Electrocatalyst for Oxygen Evolution
Liardet, L., & Hu, X. (2018) · ACS Catalysis · doi:10.1021/acscatal.7b03198 · Cited by 278
Zhuang, L., Jia, Y., Liu, H., Li, Z., Li, M., Zhang, L., Wang, X., Yang, D., Zhu, Z., & Yao, X. (2020) · Angewandte Chemie International Edition · doi:10.1002/anie.202006546 · Cited by 260
Cai, Z., Li, L., Zhang, Y., Yang, Z., Yang, J., Guo, Y., & Guo, L. (2019) · Angewandte Chemie International Edition · doi:10.1002/anie.201812601 · Cited by 227
He, W., Han, L., Hao, Q., Zheng, X., Li, Y., Zhang, J., Liu, C., Liu, H., & Xin, H. L. (2019) · ACS Energy Letters · doi:10.1021/acsenergylett.9b02316 · Cited by 223
Zhao, Q., Yang, J., Liu, M., Wang, R., Zhang, G., Wang, H., Tang, H., Liu, C., Mei, Z., Chen, H., et al. (2018) · ACS Catalysis · doi:10.1021/acscatal.8b01567 · Cited by 186
Self-citationMethods for the catalytic activation of metallic structured substrates
Montebelli, A., Visconti, C. G., Groppi, G., Tronconi, E., Cristiani, C., Ferreira, C., & Kohler, S. (2014) · Catalysis Science & Technology · doi:10.1039/c4cy00179f · Cited by 166
Li, Y., Zhang, G., Lu, W., & Cao, F. (2020) · Advanced Science · doi:10.1002/advs.201902034 · Cited by 161
Karst landform-featured monolithic electrode for water electrolysis in neutral media
Gao, X., Chen, Y., Sun, T., Huang, J., Zhang, W., Wang, Q., & Cao, R. (2020) · Energy & Environmental Science · doi:10.1039/c9ee02380a · Cited by 160
Studies on the hydrogen evolution reaction on different stainless steels
Olivares-Ramírez, J. M., Campos-Cornelio, M. L., Uribe-Godínez, J., Borja-Arco, E., & Castellanos, R. H. (2007) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2006.03.017 · Cited by 149
1D/1D Hierarchical Nickel Sulfide/Phosphide Nanostructures for Electrocatalytic Water Oxidation
Fu, H. Q., Zhang, L., Wang, C., Zheng, L., Liu, P. F., & Yang, H. G. (2018) · ACS Energy Letters · doi:10.1021/acsenergylett.8b00982 · Cited by 117
Tie, L., Li, N., Yu, C., Liu, Y., Yang, S., Chen, H., Dong, S., Sun, J., Dou, S. X., & Sun, J. (2019) · ACS Applied Energy Materials · doi:10.1021/acsaem.9b01529 · Cited by 101
Some thoughts about reporting the electrocatalytic performance of nanomaterials
Li, D., Batchelor‐McAuley, C., & Compton, R. G. (2019) · Applied Materials Today · doi:10.1016/j.apmt.2019.05.011 · Cited by 86
Kim, Y. K., Kim, J. H., Jo, Y. H., & Lee, J. S. (2019) · ACS Catalysis · doi:10.1021/acscatal.9b02701 · Cited by 73
Zhuang, L., Jia, Y. A., Liu, H., Li, Z., Li, M., Zhang, L., Wang, X., Yang, D., Zhu, Z., & Yao, X. (2020) · Angewandte Chemie · doi:10.1002/ange.202006546 · Cited by 62
Enhancing wicking microflows in metallic foams
Shum, C., Rosengarten, G., & Zhu, Y. (2017) · Microfluidics and Nanofluidics · doi:10.1007/s10404-017-2018-0 · Cited by 21
Cited by
Sun, H., Xu, X., Kim, H., Jung, W., Zhou, W., & Shao, Z. (2023) · ENERGY & ENVIRONMENTAL MATERIALS · doi:10.1002/eem2.12441 · Cited by 601
Anantharaj, S., Noda, S., Driess, M., & Menezes, P. W. (2021) · ACS Energy Letters · doi:10.1021/acsenergylett.1c00608 · Cited by 597
Anantharaj, S., Noda, S., Jothi, V. R., Yi, S., Driess, M., & Menezes, P. W. (2021) · Angewandte Chemie International Edition · doi:10.1002/anie.202015738 · Cited by 563
Precious Metal Free Hydrogen Evolution Catalyst Design and Application
Feidenhans’l, A. A., Regmi, Y. N., Wei, C., Xia, D., Kibsgaard, J., & King, L. A. (2024) · Chemical Reviews · doi:10.1021/acs.chemrev.3c00712 · Cited by 499
The Significance of Properly Reporting Turnover Frequency in Electrocatalysis Research
Anantharaj, S., Karthik, P. E., & Noda, S. (2021) · Angewandte Chemie International Edition · doi:10.1002/anie.202110352 · Cited by 494
Metadata
- Authors
- Zheng, W., Liu, M., & Lee, L. Y. S.
- Venue
- ACS Energy Letters
- Publisher
- American Chemical Society (ACS)
- Published
- 2020-09-29
- Volume
- 5
- Issue
- 10
- Pages
- 3260-3264
- ISSN
- 2380-8195 (ISSN-L)
- OpenAlex
- W3090758859
- Cited by
- 291
- References
- 34
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.