The DOI matches its Crossref record; 48 of the 48 references it cites were found in a registry or an index.
Improving the Impact Strength and Heat Resistance of 3D Printed Models: Structure, Property, and Processing Correlationships during Fused Deposition Modeling (FDM) of Poly(Lactic Acid)
Open accessAbstract
A fused deposition modeling method was used in this research to investigate the possibility of improving the mechanical properties of poly(lactic acid) by changing the thermal conditions of the printing process. Sample models were prepared while varying a wide range of printing parameters, including bed temperature, melt temperature, and raster angle. Certain samples were also thermally treated by annealing. The prepared materials were subjected to a detailed thermomechanical analysis (differential scanning calorimetry, dynamic mechanical analysis, heat deflection temperature (HDT)), which allowed the formulation of several conclusions. For all prepared samples, the key changes in mechanical properties are related to the content of the poly(lactic acid) crystalline phase, which led to superior properties in annealed samples. The results also indicate the highly beneficial effect of increased bed temperature, where the best results were obtained for the samples printed at 105 °C. Compared to the reference samples printed at a bed temperature of 60 °C, these samples showed the impact strength increased by 80% (from 35 to 63 J/m), HDT increased by 20 °C (from 55 to 75 °C), and also a significant increase in strength and modulus. Scanning electron microscopy observations confirmed the increased level of diffusion between the individual layers of the printed filament.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
An Overview of Polylactides as Packaging Materials
Auras, R., Harte, B., & Selke, S. (2004) · Macromolecular Bioscience · doi:10.1002/mabi.200400043 · Cited by 3,454
An overview of the recent developments in polylactide (PLA) research
Madhavan Nampoothiri, K., Nair, N. R., & John, R. P. (2010) · Bioresource Technology · doi:10.1016/j.biortech.2010.05.092 · Cited by 2,448
Additive manufacturing and its societal impact: a literature review
Huang, S. H., Liu, P., Mokasdar, A., & Hou, L. (2013) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-012-4558-5 · Cited by 1,862
Poly(lactic acid) crystallization
Saeidlou, S., Huneault, M. A., Li, H., & Park, C. B. (2012) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2012.07.005 · Cited by 1,606
Chacón, J. M., Caminero, M. A., García-Plaza, E., & Núñez, P. J. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.03.065 · Cited by 1,603
Parametric appraisal of mechanical property of fused deposition modelling processed parts
Sood, A. K., Ohdar, R. K., & Mahapatra, S. S. (2010) · Materials & Design · doi:10.1016/j.matdes.2009.06.016 · Cited by 1,318
Effect of processing conditions on the bonding quality of FDM polymer filaments
Sun, Q., Rizvi, G. M., Bellehumeur, C. T., & Gu, P. (2008) · Rapid Prototyping Journal · doi:10.1108/13552540810862028 · Cited by 1,277
Tymrak, B. M., Kreiger, M., & Pearce, J. M. (2014) · Materials & Design · doi:10.1016/j.matdes.2014.02.038 · Cited by 1,244
Natural Fibers, Biopolymers, and Biocomposites: An Introduction
Mohanty, A., Misra, M., Drzal, L., Selke, S., Harte, B., & Hinrichsen, G. (2005) · Natural Fibers, Biopolymers, and Biocomposites · doi:10.1201/9780203508206.ch1 · Cited by 976
Self-citationNagarajan, V., Mohanty, A. K., & Misra, M. (2016) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.6b00321 · Cited by 926
Self-citationEffect of nucleation and plasticization on the crystallization of poly (lactic acid)
Li, H., & Huneault, M. A. (2007) · Polymer · doi:10.1016/j.polymer.2007.09.020 · Cited by 810
Modeling of Bond Formation Between Polymer Filaments in the Fused Deposition Modeling Process
Bellehumeur, C., Li, L., Sun, Q., & Gu, P. (2004) · Journal of Manufacturing Processes · doi:10.1016/s1526-6125(04)70071-7 · Cited by 768
Yang, C., Tian, X., Li, D., Cao, Y., Zhao, F., & Shi, C. (2017) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2017.04.027 · Cited by 662
Mechanical characterization of parts fabricated using fused deposition modeling
Bellini, A., & Güçeri, S. (2003) · Rapid Prototyping Journal · doi:10.1108/13552540310489631 · Cited by 628
Measurements of the mechanical response of unidirectional 3D-printed PLA
Song, Y., Li, Y., Song, W., Yee, K., Lee, K.-Y., & Tagarielli, V. L. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.03.051 · Cited by 624
Weng, Z., Wang, J., Senthil, T., & Wu, L. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.04.045 · Cited by 609
Improving mechanical performance of injection molded PLA by controlling crystallinity
Harris, A. M., & Lee, E. C. (2008) · Journal of Applied Polymer Science · doi:10.1002/app.27261 · Cited by 545
Durgun, I., & Ertan, R. (2014) · Rapid Prototyping Journal · doi:10.1108/rpj-10-2012-0091 · Cited by 530
Casavola, C., Cazzato, A., Moramarco, V., & Pappalettere, C. (2015) · Materials & Design · doi:10.1016/j.matdes.2015.11.009 · Cited by 493
The effects of PLA color on material properties of 3-D printed components
Wittbrodt, B., & Pearce, J. M. (2015) · Additive manufacturing · doi:10.1016/j.addma.2015.09.006 · Cited by 473
Thermal analysis of the double‐melting behavior of poly(L‐lactic acid)
Yasuniwa, M., Tsubakihara, S., Sugimoto, Y., & Nakafuku, C. (2004) · Journal of Polymer Science Part B: Polymer Physics · doi:10.1002/polb.10674 · Cited by 375
Rapid prototyping or rapid production? 3D printing processes move industry towards the latter
Bak, D. (2003) · Assembly Automation · doi:10.1108/01445150310501190 · Cited by 353
Crystallization kinetics of poly(lactic acid)-talc composites
Battegazzore, D., Bocchini, S., & Frache, A. (2011) · Express Polymer Letters · doi:10.3144/expresspolymlett.2011.84 · Cited by 345
Material Property Testing of 3D-Printed Specimen in PLA on an Entry-Level 3D Printer
Letcher, T., & Waytashek, M. (2014) · Volume 2A: Advanced Manufacturing · doi:10.1115/imece2014-39379 · Cited by 325
Improving the impact strength of Poly(lactic acid) (PLA) in fused layer modeling (FLM)
Wang, L., Gramlich, W. M., & Gardner, D. J. (2017) · Polymer · doi:10.1016/j.polymer.2017.03.011 · Cited by 310
Estimation of filament temperature and adhesion development in fused deposition techniques
Costa, S. F., Duarte, F. M., & Covas, J. A. (2017) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2017.02.026 · Cited by 293
Weld formation during material extrusion additive manufacturing
Seppala, J. E., Hoon Han, S., Hillgartner, K. E., Davis, C. S., & Migler, K. B. (2017) · Soft Matter · doi:10.1039/c7sm00950j · Cited by 291
Process-structure-property effects on ABS bond strength in fused filament fabrication
Abbott, A. C., Tandon, G. P., Bradford, R. L., Koerner, H., & Baur, J. W. (2018) · Additive Manufacturing · doi:10.1016/j.addma.2017.11.002 · Cited by 291
3-D Printing of Open Source Appropriate Technologies for Self-Directed Sustainable Development
Pearce, J. M., Morris Blair, C., Laciak, K. J., Andrews, R., Nosrat, A., & Zelenika-Zovko, I. (2010) · Journal of Sustainable Development · doi:10.5539/jsd.v3n4p17 · Cited by 271
Nagarajan, V., Zhang, K., Misra, M., & Mohanty, A. K. (2015) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.5b01145 · Cited by 232
Self-citationEnthalpy of melting of α′- and α-crystals of poly(l-lactic acid)
Righetti, M. C., Gazzano, M., Di Lorenzo, M. L., & Androsch, R. (2015) · European Polymer Journal · doi:10.1016/j.eurpolymj.2015.07.024 · Cited by 215
Suitability of PLA/TCP for fused deposition modeling
Drummer, D., Cifuentes‐Cuéllar, S., & Rietzel, D. (2012) · Rapid Prototyping Journal · doi:10.1108/13552541211272045 · Cited by 210
Thermal analysis of additive manufacturing of large-scale thermoplastic polymer composites
Compton, B. G., Post, B., Duty, C., Love, L. J., & Kunc, V. (2017) · Additive manufacturing · doi:10.1016/j.addma.2017.07.006 · Cited by 206
In-situ monitoring of strain and temperature distributions during fused deposition modeling process
Kousiatza, C., & Karalekas, D. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.02.099 · Cited by 205
Warpage of FDM parts: Experimental tests and analytic model
Armillotta, A., Bellotti, M., & Cavallaro, M. (2018) · Robotics and Computer-Integrated Manufacturing · doi:10.1016/j.rcim.2017.09.007 · Cited by 193
Tábi, T., Hajba, S., & Kovács, J. G. (2016) · European Polymer Journal · doi:10.1016/j.eurpolymj.2016.07.024 · Cited by 175
Mechanical strength of welding zones produced by polymer extrusion additive manufacturing
Davis, C. S., Hillgartner, K. E., Han, S. H., & Seppala, J. E. (2017) · Additive manufacturing · doi:10.1016/j.addma.2017.06.006 · Cited by 144
Cicala, G., Latteri, A., Curto, B. D., Russo, A. L., Recca, G., & Farè, S. (2017) · Journal of Applied Biomaterials & Functional Materials · doi:10.5301/jabfm.5000343 · Cited by 114
Cocca, M., Androsch, R., Righetti, M. C., Malinconico, M., & Di Lorenzo, M. L. (2014) · Journal of Molecular Structure · doi:10.1016/j.molstruc.2014.02.038 · Cited by 92
Santana, L., Alves, J. L., & Netto, A. D. C. S. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.09.020 · Cited by 78
Wei, Z., Song, P., Zhou, C. Y., Chen, G., Chang, Y., Li, J., Zhang, W., & Liang, J. (2013) · Polymer · doi:10.1016/j.polymer.2013.04.027 · Cited by 54
Vadori, R., Mohanty, A. K., & Misra, M. (2013) · Macromolecular Materials and Engineering · doi:10.1002/mame.201200274 · Cited by 51
Self-citationOn the kinetics of melting and crystallization of poly(l-lactic acid) by TMDSC
Salmerón‐Sánchez, M., Ribelles, J. L. G., Hernández‐Sánchez, F., & Mano, J. F. (2005) · Thermochimica Acta · doi:10.1016/j.tca.2005.01.066 · Cited by 46
Yang, T.-C., Hung, K., Wu, T.-L., Wu, T., & Wu, J. (2015) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2015.09.012 · Cited by 36
Effect of cooling conditions on the mechanical properties of crystalline poly(lactic acid)
Huang, T., & Yamaguchi, M. (2017) · Journal of Applied Polymer Science · doi:10.1002/app.44960 · Cited by 30
Microstructures and mechanical properties of polylactic acid prepared by a cold rolling process
Wang, L., Qiu, J., & Sakai, E. (2016) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2016.02.006 · Cited by 27
Drumright, R. E., Gruber, P. R., & Henton, D. E. (2000) · Advanced Materials · doi:10.1002/1521-4095(200012)12:23<1841::aid-adma1841>3.0.co;2-e
Perego (1998) · doi:10.1002/(sici)1097-4628(19960103)59:1<37::aid-app6>3.0.co;2-n
Cited by
Wickramasinghe, S., Do, T., & Tran, P. (2020) · Polymers · doi:10.3390/polym12071529 · Cited by 1,052
Fused deposition modeling: process, materials, parameters, properties, and applications
Rajan, K., Samykano, M., Kadirgama, K., Harun, W. S. W., & Rahman, M. M. (2022) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-022-08860-7 · Cited by 426
Recent Advances in Bioplastics: Application and Biodegradation
Narancic, T., Cerrone, F., Beagan, N., & O’Connor, K. E. (2020) · Polymers · doi:10.3390/polym12040920 · Cited by 421
Fused filament fabrication of polymer materials: A review of interlayer bond
Gao, X., Qi, S., Kuang, X., Su, Y., Li, J., & Wang, D. (2021) · Additive Manufacturing · doi:10.1016/j.addma.2020.101658 · Cited by 418
Lay, M., Thajudin, N. L. N., Hamid, Z. A. A., Rusli, A., Abdullah, M. K., & Shuib, R. K. (2019) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2019.107341 · Cited by 393
Metadata
- Authors
- Benwood, C., Anstey, A., Andrzejewski, J., Misra, M., & Mohanty, A. K.
- Venue
- ACS Omega
- Publisher
- American Chemical Society (ACS)
- Published
- 2018-04-23
- Volume
- 3
- Issue
- 4
- Pages
- 4400-4411
- ISSN
- 2470-1343 (ISSN-L)
- OpenAlex
- W2801723236
- Cited by
- 262
- References
- 48
- FWCI
- 12.74
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.