The DOI matches its Crossref record; 72 of the 72 references it cites were found in a registry or an index.
Unreacted PbI2 as a Double-Edged Sword for Enhancing the Performance of Perovskite Solar Cells
Open accessAbstract
Lead halide perovskites have over the past few years attracted considerable interest as photo absorbers in PV applications with record efficiencies now reaching 22%. It has recently been found that not only the composition but also the precise stoichiometry is important for the device performance. Recent reports have, for example, demonstrated small amount of PbI2 in the perovskite films to be beneficial for the overall performance of both the standard perovskite, CH3NH3PbI3, as well as for the mixed perovskites (CH3NH3)x(CH(NH2)2)(1-x)PbBryI(3-y). In this work a broad range of characterization techniques including X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), photo electron spectroscopy (PES), transient absorption spectroscopy (TAS), UV-vis, electroluminescence (EL), photoluminescence (PL), and confocal PL mapping have been used to further understand the importance of remnant PbI2 in perovskite solar cells. Our best devices were over 18% efficient, and had in line with previous results a small amount of excess PbI2. For the PbI2-deficient samples, the photocurrent dropped, which could be attributed to accumulation of organic species at the grain boundaries, low charge carrier mobility, and decreased electron injection into the TiO2. The PbI2-deficient compositions did, however, also have advantages. The record Voc was as high as 1.20 V and was found in PbI2-deficient samples. This was correlated with high crystal quality, longer charge carrier lifetimes, and high PL yields and was rationalized as a consequence of the dynamics of the perovskite formation. We further found the ion migration to be obstructed in the PbI2-deficient samples, which decreased the JV hysteresis and increased the photostability. PbI2-deficient synthesis conditions can thus be used to deposit perovskites with excellent crystal quality but with the downside of grain boundaries enriched in organic species, which act as a barrier toward current transport. Exploring ways to tune the synthesis conditions to give the high crystal quality obtained under PbI2-poor condition while maintaining the favorable grain boundary characteristics obtained under PbI2-rich conditions would thus be a strategy toward more efficiency devices.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Organometal Halide Perovskites as Visible-Light Sensitizers for Photovoltaic Cells
Kojima, A., Teshima, K., Shirai, Y., & Miyasaka, T. (2009) · Journal of the American Chemical Society · doi:10.1021/ja809598r · Cited by 23,090
Efficient Hybrid Solar Cells Based on Meso-Superstructured Organometal Halide Perovskites
Lee, M. M., Teuscher, J., Miyasaka, T., Murakami, T. N., & Snaith, H. J. (2012) · Science · doi:10.1126/science.1228604 · Cited by 10,687
Self-citationStranks, S. D., Eperon, G. E., Grancini, G., Menelaou, C., Alcocer, M. J. P., Leijtens, T., Herz, L. M., Petrozza, A., & Snaith, H. J. (2013) · Science · doi:10.1126/science.1243982 · Cited by 10,413
Self-citationSequential deposition as a route to high-performance perovskite-sensitized solar cells
Burschka, J., Pellet, N., Moon, S.-J., Humphry-Baker, R., Gao, P., Nazeeruddin, M. K., & Grätzel, M. (2013) · Nature · doi:10.1038/nature12340 · Cited by 9,547
Kim, H.-S., Lee, C.-R., Im, J.-H., Lee, K.-B., Moehl, T., Marchioro, A., Moon, S.-J., Humphry-Baker, R., Yum, J.-H., Moser, J. E., et al. (2012) · Scientific Reports · doi:10.1038/srep00591 · Cited by 8,092
Self-citationLong-Range Balanced Electron- and Hole-Transport Lengths in Organic-Inorganic CH 3 NH 3 PbI 3
Xing, G., Mathews, N., Sun, S., Lim, S. S., Lam, Y. M., Grätzel, M., Mhaisalkar, S., & Sum, T. C. (2013) · Science · doi:10.1126/science.1243167 · Cited by 6,909
Solvent engineering for high-performance inorganic–organic hybrid perovskite solar cells
Jeon, N. J., Noh, J. H., Kim, Y. C., Yang, W. S., Ryu, S., & Seok, S. I. (2014) · Nature Materials · doi:10.1038/nmat4014 · Cited by 6,723
Compositional engineering of perovskite materials for high-performance solar cells
Jeon, N. J., Noh, J. H., Yang, W. S., Kim, Y. C., Ryu, S., Seo, J., & Seok, S. I. (2015) · Nature · doi:10.1038/nature14133 · Cited by 6,431
High-performance photovoltaic perovskite layers fabricated through intramolecular exchange
Yang, W. S., Noh, J. H., Jeon, N. J., Kim, Y. C., Ryu, S., Seo, J., & Seok, S. I. (2015) · Science · doi:10.1126/science.aaa9272 · Cited by 6,251
6.5% efficient perovskite quantum-dot-sensitized solar cell
Im, J.-H., Lee, C.-R., Lee, J.-W., Park, S.-W., & Park, N.-G. (2011) · Nanoscale · doi:10.1039/c1nr10867k · Cited by 3,173
Cited by
Iodide management in formamidinium-lead-halide–based perovskite layers for efficient solar cells
Yang, W. S., Park, B.-W., Jung, E. H., Jeon, N. J., Kim, Y. C., Lee, D. U., Shin, S. S., Seo, J., Kim, E. K., Noh, J. H., et al. (2017) · Science · doi:10.1126/science.aan2301 · Cited by 5,445
Halide Perovskite Photovoltaics: Background, Status, and Future Prospects
Jena, A. K., Kulkarni, A., & Miyasaka, T. (2019) · Chemical Reviews · doi:10.1021/acs.chemrev.8b00539 · Cited by 3,087
Inactive (PbI 2 ) 2 RbCl stabilizes perovskite films for efficient solar cells
Zhao, Y., Ma, F., Qu, Z., Yu, S., Shen, T., Deng, H.-X., Chu, X., Peng, X., Yuan, Y., Zhang, X., et al. (2022) · Science · doi:10.1126/science.abp8873 · Cited by 1,445
Sherkar, T. S., Momblona, C., Gil-Escrig, L., Ávila, J., Sessolo, M., Bolink, H. J., & Koster, L. J. A. (2017) · ACS Energy Letters · doi:10.1021/acsenergylett.7b00236 · Cited by 1,280
Planar‐Structure Perovskite Solar Cells with Efficiency beyond 21%
Jiang, Q., Chu, Z., Wang, P., Yang, X., Liu, H., Wang, Y., Yin, Z., Wu, J., Zhang, X., & You, J. (2017) · Advanced Materials · doi:10.1002/adma.201703852 · Cited by 1,250
The rapid evolution of highly efficient perovskite solar cells
Correa-Baena, J.-P., Abate, A., Saliba, M., Tress, W., Jesper Jacobsson, T., Grätzel, M., & Hagfeldt, A. (2017) · Energy & Environmental Science · doi:10.1039/c6ee03397k · Cited by 1,140
Self-citationHighly efficient and stable planar perovskite solar cells by solution-processed tin oxide
Anaraki, E. H., Kermanpur, A., Steier, L., Domanski, K., Matsui, T., Tress, W., Saliba, M., Abate, A., Grätzel, M., Hagfeldt, A., et al. (2016) · Energy & Environmental Science · doi:10.1039/c6ee02390h · Cited by 848
Self-citationTress, W., Yavari, M., Domanski, K., Yadav, P., Niesen, B., Correa Baena, J. P., Hagfeldt, A., & Graetzel, M. (2018) · Energy & Environmental Science · doi:10.1039/c7ee02415k · Cited by 843
Self-citationPerovskite precursor solution chemistry: from fundamentals to photovoltaic applications
Jung, M., Ji, S.-G., Kim, G., & Seok, S. I. (2019) · Chemical Society Reviews · doi:10.1039/c8cs00656c · Cited by 816
Stabilizing black-phase formamidinium perovskite formation at room temperature and high humidity
Hui, W., Chao, L., Lu, H., Xia, F., Wei, Q., Su, Z., Niu, T., Tao, L., Du, B., Li, D., et al. (2021) · Science · doi:10.1126/science.abf7652 · Cited by 806
Additive Engineering for Efficient and Stable Perovskite Solar Cells
Zhang, F., & Zhu, K. (2020) · Advanced Energy Materials · doi:10.1002/aenm.201902579 · Cited by 805
In Situ Growth of 2D Perovskite Capping Layer for Stable and Efficient Perovskite Solar Cells
Chen, P., Bai, Y., Wang, S., Lyu, M., Yun, J., & Wang, L. (2018) · Advanced Functional Materials · doi:10.1002/adfm.201706923 · Cited by 776
Defect and Contact Passivation for Perovskite Solar Cells
Aydin, E., De Bastiani, M., & De Wolf, S. (2019) · Advanced Materials · doi:10.1002/adma.201900428 · Cited by 681
Boyd, C. C., Shallcross, R. C., Moot, T., Kerner, R., Bertoluzzi, L., Onno, A., Kavadiya, S., Chosy, C., Wolf, E. J., Werner, J., et al. (2020) · Joule · doi:10.1016/j.joule.2020.06.004 · Cited by 639
Ran, C., Xu, J., Gao, W., Huang, C., & Dou, S. (2018) · Chemical Society Reviews · doi:10.1039/c7cs00868f · Cited by 634
Synthetic Approaches for Halide Perovskite Thin Films
Dunlap-Shohl, W. A., Zhou, Y., Padture, N. P., & Mitzi, D. B. (2019) · Chemical Reviews · doi:10.1021/acs.chemrev.8b00318 · Cited by 631
Tress, W. (2017) · Advanced Energy Materials · doi:10.1002/aenm.201602358 · Cited by 601
Self-citationOrigins and influences of metallic lead in perovskite solar cells
Liang, J., Hu, X., Wang, C., Liang, C., Chen, C., Xiao, M., Li, J., Tao, C., Xing, G., Yu, R., et al. (2022) · Joule · doi:10.1016/j.joule.2022.03.005 · Cited by 576
Defects engineering for high-performance perovskite solar cells
Wang, F., Bai, S., Tress, W., Hagfeldt, A., & Gao, F. (2018) · npj Flexible Electronics · doi:10.1038/s41528-018-0035-z · Cited by 568
Self-citationHalide Perovskites: Is It All about the Interfaces?
Schulz, P., Cahen, D., & Kahn, A. (2019) · Chemical Reviews · doi:10.1021/acs.chemrev.8b00558 · Cited by 558
Nam, J. K., Chai, S. U., Cha, W., Choi, Y. J., Kim, W., Jung, M. S., Kwon, J., Kim, D., & Park, J. H. (2017) · Nano Letters · doi:10.1021/acs.nanolett.7b00050 · Cited by 524
Duong, T., Wu, Y., Shen, H., Peng, J., Fu, X., Jacobs, D., Wang, E., Kho, T. C., Fong, K. C., Stocks, M., et al. (2017) · Advanced Energy Materials · doi:10.1002/aenm.201700228 · Cited by 519
Bu, T., Liu, X., Zhou, Y., Yi, J., Huang, X., Luo, L., Xiao, J., Ku, Z., Peng, Y., Huang, F., et al. (2017) · Energy & Environmental Science · doi:10.1039/c7ee02634j · Cited by 516
Defect passivation strategies in perovskites for an enhanced photovoltaic performance
Fu, L., Li, H., Wang, L., Yin, R., Li, B., & Yin, L. (2020) · Energy & Environmental Science · doi:10.1039/d0ee01767a · Cited by 463
A general approach to high-efficiency perovskite solar cells by any antisolvent
Taylor, A. D., Sun, Q., Goetz, K. P., An, Q., Schramm, T., Hofstetter, Y., Litterst, M., Paulus, F., & Vaynzof, Y. (2021) · Nature Communications · doi:10.1038/s41467-021-22049-8 · Cited by 451
Buried Interfaces in Halide Perovskite Photovoltaics
Yang, X., Luo, D., Xiang, Y., Zhao, L., Anaya, M., Shen, Y., Wu, J., Yang, W., Chiang, Y., Tu, Y., et al. (2021) · Advanced Materials · doi:10.1002/adma.202006435 · Cited by 443
Self-citationThe high open-circuit voltage of perovskite solar cells: a review
Guo, Z., Jena, A. K., Kim, G. M., & Miyasaka, T. (2022) · Energy & Environmental Science · doi:10.1039/d2ee00663d · Cited by 430
A Review on Additives for Halide Perovskite Solar Cells
Liu, S., Guan, Y., Sheng, Y., Hu, Y., Rong, Y., Mei, A., & Han, H. (2020) · Advanced Energy Materials · doi:10.1002/aenm.201902492 · Cited by 425
Noel, N. K., Habisreutinger, S. N., Wenger, B., Klug, M. T., Hörantner, M. T., Johnston, M. B., Nicholas, R. J., Moore, D. T., & Snaith, H. J. (2017) · Energy & Environmental Science · doi:10.1039/c6ee02373h · Cited by 413
Ye, S., Rao, H., Zhao, Z., Zhang, L., Bao, H., Sun, W., Li, Y., Gu, F., Wang, J., Liu, Z., et al. (2017) · Journal of the American Chemical Society · doi:10.1021/jacs.7b01439 · Cited by 401
Understanding how excess lead iodide precursor improves halide perovskite solar cell performance
Park, B.-W., Kedem, N., Kulbak, M., Lee, D. Y., Yang, W. S., Jeon, N. J., Seo, J., Kim, G., Kim, K. J., Shin, T. J., et al. (2018) · Nature Communications · doi:10.1038/s41467-018-05583-w · Cited by 391
Chemical Reduction of Intrinsic Defects in Thicker Heterojunction Planar Perovskite Solar Cells
Liu, Z., Hu, J., Jiao, H., Li, L., Zheng, G., Chen, Y., Huang, Y., Zhang, Q., Shen, C., Chen, Q., et al. (2017) · Advanced Materials · doi:10.1002/adma.201606774 · Cited by 383
Capturing the Sun: A Review of the Challenges and Perspectives of Perovskite Solar Cells
Petrus, M. L., Schlipf, J., Li, C., Gujar, T. P., Giesbrecht, N., Müller‐Buschbaum, P., Thelakkat, M., Bein, T., Hüttner, S., & Docampo, P. (2017) · Advanced Energy Materials · doi:10.1002/aenm.201700264 · Cited by 374
Jacobsson, T. J., Hultqvist, A., García-Fernández, A., Anand, A., Al-Ashouri, A., Hagfeldt, A., Crovetto, A., Abate, A., Ricciardulli, A. G., Vijayan, A., et al. (2021) · Nature Energy · doi:10.1038/s41560-021-00941-3 · Cited by 372
Self-citationA review of aspects of additive engineering in perovskite solar cells
Mahapatra, A., Prochowicz, D., Tavakoli, M. M., Trivedi, S., Kumar, P., & Yadav, P. (2020) · Journal of Materials Chemistry A · doi:10.1039/c9ta07657c · Cited by 369
Homogenized halides and alkali cation segregation in alloyed organic-inorganic perovskites
Correa-Baena, J.-P., Luo, Y., Brenner, T. M., Snaider, J., Sun, S., Li, X., Jensen, M. A., Hartono, N. T. P., Nienhaus, L., Wieghold, S., et al. (2019) · Science · doi:10.1126/science.aah5065 · Cited by 364
Self-citationEnergy Level Alignment at Interfaces in Metal Halide Perovskite Solar Cells
Wang, S., Sakurai, T., Wen, W., & Qi, Y. (2018) · Advanced Materials Interfaces · doi:10.1002/admi.201800260 · Cited by 350
Correa-Baena, J.-P., Tress, W., Domanski, K., Anaraki, E. H., Turren-Cruz, S.-H., Roose, B., Boix, P. P., Grätzel, M., Saliba, M., Abate, A., et al. (2017) · Energy & Environmental Science · doi:10.1039/c7ee00421d · Cited by 338
Self-citationNonradiative Losses in Metal Halide Perovskites
Stranks, S. D. (2017) · ACS Energy Letters · doi:10.1021/acsenergylett.7b00239 · Cited by 336
Self-citationCho, Y., Soufiani, A. M., Yun, J. S., Kim, J., Lee, D. S., Seidel, J., Deng, X., Green, M. A., Huang, S., & Ho‐Baillie, A. W. Y. (2018) · Advanced Energy Materials · doi:10.1002/aenm.201703392 · Cited by 334
The Role of Grain Boundaries in Perovskite Solar Cells
Castro‐Méndez, A., Hidalgo, J., & Correa‐Baena, J. (2019) · Advanced Energy Materials · doi:10.1002/aenm.201901489 · Cited by 330
Self-citationSynergic Interface Optimization with Green Solvent Engineering in Mixed Perovskite Solar Cells
Bu, T., Wu, L., Liu, X., Yang, X., Zhou, P., Yu, X., Qin, T., Shi, J., Wang, S., Li, S., et al. (2017) · Advanced Energy Materials · doi:10.1002/aenm.201700576 · Cited by 309
Development of Dopant‐Free Organic Hole Transporting Materials for Perovskite Solar Cells
Pham, H. D., Yang, T. C., Jain, S. M., Wilson, G. J., & Sonar, P. (2020) · Advanced Energy Materials · doi:10.1002/aenm.201903326 · Cited by 301
The Promise and Challenges of Inverted Perovskite Solar Cells
Chen, P., Xiao, Y., Li, S., Jia, X., Luo, D., Zhang, W., Snaith, H. J., Gong, Q., & Zhu, R. (2024) · Chemical Reviews · doi:10.1021/acs.chemrev.4c00073 · Cited by 297
Zhou, Q., Liang, L., Hu, J., Cao, B., Yang, L., Wu, T., Li, X., Zhang, B., & Gao, P. (2019) · Advanced Energy Materials · doi:10.1002/aenm.201802595 · Cited by 294
Grain‐Boundary “Patches” by In Situ Conversion to Enhance Perovskite Solar Cells Stability
Liu, L., Huang, S., Lu, Y., Liu, P., Zhao, Y., Shi, C., Zhang, S., Wu, J., Zhong, H., Sui, M., et al. (2018) · Advanced Materials · doi:10.1002/adma.201800544 · Cited by 283
Impact of Interfacial Layers in Perovskite Solar Cells
Cho, A., & Park, N. (2017) · ChemSusChem · doi:10.1002/cssc.201701095 · Cited by 281
Mechanisms for light induced degradation in MAPbI3 perovskite thin films and solar cells
Abdelmageed, G., Jewell, L., Hellier, K., Seymour, L., Luo, B., Bridges, F., Zhang, J. Z., & Carter, S. (2016) · Applied Physics Letters · doi:10.1063/1.4967840 · Cited by 279
Manipulation of facet orientation in hybrid perovskite polycrystalline films by cation cascade
Zheng, G., Zhu, C., Ma, J., Zhang, X., Tang, G., Li, R., Chen, Y., Li, L., Hu, J., Hong, J., et al. (2018) · Nature Communications · doi:10.1038/s41467-018-05076-w · Cited by 278
Defect activity in metal halide perovskites with wide and narrow bandgap
Zhou, Y., Poli, I., Meggiolaro, D., De Angelis, F., & Petrozza, A. (2021) · Nature Reviews Materials · doi:10.1038/s41578-021-00331-x · Cited by 275
Park, B.-W., Kwon, H. W., Lee, Y., Lee, D. Y., Kim, M. G., Kim, G., Kim, K.-J., Kim, Y. K., Im, J., Shin, T. J., et al. (2021) · Nature Energy · doi:10.1038/s41560-021-00802-z · Cited by 263
Mechanisms and Suppression of Photoinduced Degradation in Perovskite Solar Cells
Wei, J., Wang, Q., Huo, J., Gao, F., Gan, Z., Zhao, Q., & Li, H. (2021) · Advanced Energy Materials · doi:10.1002/aenm.202002326 · Cited by 260
Solution-Processed All-Perovskite Multi-junction Solar Cells
McMeekin, D. P., Mahesh, S., Noel, N. K., Klug, M. T., Lim, J., Warby, J. H., Ball, J. M., Herz, L. M., Johnston, M. B., & Snaith, H. J. (2019) · Joule · doi:10.1016/j.joule.2019.01.007 · Cited by 257
Understanding Detrimental and Beneficial Grain Boundary Effects in Halide Perovskites
Adhyaksa, G. W. P., Brittman, S., Āboliņš, H., Lof, A., Li, X., Keelor, J. D., Luo, Y., Duevski, T., Heeren, R. M. A., Ellis, S. R., et al. (2018) · Advanced Materials · doi:10.1002/adma.201804792 · Cited by 197
Control over Crystal Size in Vapor Deposited Metal-Halide Perovskite Films
Lohmann, K. B., Patel, J. B., Rothmann, M. U., Xia, C. Q., Oliver, R. D. J., Herz, L. M., Snaith, H. J., & Johnston, M. B. (2020) · ACS Energy Letters · doi:10.1021/acsenergylett.0c00183 · Cited by 113
Mechanical Durability and Flexibility in Perovskite Photovoltaics: Advancements and Applications
Song, F., Zheng, D., Feng, J., Liu, J., Ye, T., Li, Z., Wang, K., Liu, S. (., & Yang, D. (2024) · Advanced Materials · doi:10.1002/adma.202312041 · Cited by 113
Flexible and Wearable Optoelectronic Devices Based on Perovskites
Zhao, R., Gu, Z., Li, P., Zhang, Y., & Song, Y. (2022) · Advanced Materials Technologies · doi:10.1002/admt.202101124 · Cited by 83
Triple cation mixed-halide perovskites for tunable lasers
Brenner, P., Glöckler, T., Rueda-Delgado, D., Abzieher, T., Jakoby, M., Richards, B. S., Paetzold, U. W., Howard, I. A., & Lemmer, U. (2017) · Optical Materials Express · doi:10.1364/ome.7.004082 · Cited by 42
Metadata
- Authors
- Jacobsson, T. J., Correa-Baena, J.-P., Halvani Anaraki, E., Philippe, B., Stranks, S. D., Bouduban, M. E. F., Tress, W., Schenk, K., Teuscher, J., Moser, J.-E., Rensmo, H., & Hagfeldt, A.
- Venue
- Journal of the American Chemical Society
- Publisher
- American Chemical Society (ACS)
- Published
- 2016-08-04
- Volume
- 138
- Issue
- 32
- Pages
- 10331-10343
- ISSN
- 0002-7863 (ISSN-L)
- 1520-5126
- OpenAlex
- W2482154572
- Cited by
- 901
- References
- 72
- FWCI
- 42.38
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.