The DOI matches its Crossref record; 38 of the 38 references it cites were found in a registry or an index; 11 of the 27 sources its claims cite were checked for support.
Shape memory polymer with programmable recovery onset
Open accessPublished version of a preprint
Abstract
A four-dimensional printable shape memory hydrogel with shape-shifting onset adjustable by changing the programming conditions is reported. Here we achieved this goal with a four-dimensional printable shape memory hydrogel that operates via phase separation, with its shape-shifting kinetics dominated by internal mass diffusion rather than by heat transport used for common shape memory polymers.
Overview
CoChat Summary
TL;DR
The authors report a 4D-printable shape memory hydrogel whose autonomous shape recovery is governed by internal mass diffusion (spinodal decomposition) rather than thermal conduction, allowing the recovery onset to be programmed on demand. The onset period can be tuned from 1 min to 22 min by varying the heating time during programming, while the material still recovers fully without any external trigger.
Key findings
- The hydrogel reaches thermal equilibrium within 10 seconds of cooling to 25 °C, yet shape recovery starts only ~10 min later, demonstrating that recovery onset is decoupled from heat conduction and instead dominated by spinodal decomposition and internal water redistribution.
- The recovery onset period (t_onset, defined as time to 5% recovery) can be finely tuned from 1 min to 22 min by varying the programming heating time from 1 min to 400 min; heating beyond 400 min does not increase t_onset further, indicating equilibrium phase separation.
- Morphology and modulus track the onset: after 180 min at 90 °C and 10 min of natural cooling, phase-separated feature size shrinks from 50 µm to 10 µm and modulus falls to 141 MPa, at which point chains remain too stiff to recover.
- t_onset is largely independent of sample thickness and of whether water or oil is the surrounding medium, unlike conventional shape memory hydrogels whose kinetics depend strongly on device dimension; crosslinking density affects t_onset non-monotonically, with 0.25–2.5 mol% crosslinker giving the shortest t_onset.
- Demonstrations include a stent that deploys at the intended site in 25 °C water (versus premature deployment of a classical SMP stent in 70 °C water), a rigid-then-soft probe that punctures a stiff barrier before deploying in soft gelatin, and spatially programmed sequential recovery of three regions.
Methods
- Design: an aqueous photocurable resin of acrylic acid (AAc), N,N'-methylenebisacrylamide (BIS), photo-initiator (I819), and water, photo-cured then soaked in calcium acetate solution and deionized water; the 0.25 mol% BIS sample was selected for its optimal mechanical properties (modulus 1.12 GPa at 90 °C, 314 kPa at 25 °C).
- Shape memory protocol: a flat sheet is deformed into a "windmill" at room temperature, heated at 90 °C under load to fix the temporary shape, then cooled to 25 °C for autonomous recovery.
- Characterization: confocal laser scanning microscopy for phase morphology, infrared imaging for temperature, modulus/thermomechanical measurements, DSC for enthalpy versus crosslinking density, plus 3D-printed device demonstrations.
Limitations
- The paper states no explicit limitations. The preprint header itself notes the work "should not be considered conclusive, used to inform clinical practice, or referenced by the media as validated information."
- Evident from the text: the mechanism is demonstrated only in one hydrogel chemistry (AAc/BIS/CaAc), and the claim that the spinodal-decomposition principle "can potentially inspire future design of other types of shape-shifting materials" is proposed rather than tested; several supporting results (thickness independence, oil medium, crosslinker series, strain independence) are reported only in Supplementary figures, and device demonstrations are benchtop mimics of body/vessel environments rather than in vivo tests.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
9 Valid · 0 Not valid · 3 Not checked · 54 Own results and interpretations
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“This autonomous multi-shape transformation is drastically different from existing examples that would otherwise require complexed stimulation schemes (e.g. multi-step heating 17,18 ) that are difficult to implement for many applications.”
What the sources say
- Not checked — no full text of the sourcecites [17] Xie, T. Tunable polymer multi-shape memory effect. Nature 464, 267–279 (2010). source
- Partly supportedcites [18] Liu, Y., Shaw, B., Dickey, M. D. & Genzer, J. Sequential self-folding of polymer sheets. Sci. Adv. 3, e1602417 (2017). sourceExperimental — accuracy not yet measured
The Introduction says earlier approaches to sequential shape transformation can require “multistep fabrication or complex (and sometimes, incompatible) sequences of stimuli.” The Conclusions contrast these with the paper’s simpler, light-driven folding method. Our copy does not specifically identify multistep heating as an example or say that such schemes are difficult to implement for many applications; section labels are available, but page numbers are not. (LLM, conf=0.82)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The sources with a verdict support this claim; the rest weren’t checked yet, have no full text we could read, or their verdicts aren’t rated yet.
In the paper
“Temporal programming 11,12 offers a drastically different alternative.”
What the sources say
- Not checked — no full text of the sourcecites [11] Koerner, H., Price, G., Pearce, N. A., Alexander, M. & Vaia, R. A. Remotely actuated polymer nanocomposites-stress-recovery of carbon-nanotube-filled thermoplastic elastomers. Nat. Mater. 3, 115–120 (2004). source
- Supportedcites [12] Hu, X. et al. Programming temporal shapeshifting. Nat. Commun. 7, 12919 (2016). source
The Abstract describes temporal programming that encodes shape transformations without an external trigger. The Results section (‘Controlling the rate and pathway of shapeshifting’) explicitly contrasts this approach with conventional stimulus-triggered shape recovery, supporting its characterization as a different alternative. (LLM, conf=0.88)
boosted- Asserted: passes — The authors put it forward as true.
- Checkable: unclear — It is unclear whether it could be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Ironically, accessing external stimulation (e.g. heating or light) under realistic scenarios has become the biggest bottleneck for increasingly demanding applications such as implantable medical devices8.”
- Also stated in: § Full Text · p. 2 · plain
“Although this ondemand response is beneficial in many circumstances, the need to apply external stimulation has increasingly become the bottleneck for many demanding applications.”
- Also stated in: § Full Text · p. 2 · plain
“There, access to active heating or other forms of stimulation is a major hurdle.”
What the sources say
- Partly supportedcites [8] Lendlein, A., Behl, M., Hiebl, B. & Wischke, C. Shape-memory polymers as a technology platform for biomedical applications. Expert Rev. Med. Devices 7, 357–379 (2010). sourceExperimental — accuracy not yet measured
The Five-year view (page unavailable) identifies direct access to implanted materials as a challenge and calls for on-demand actuation independent of body temperature. The Vascular applications section (page unavailable) also reports difficulty achieving light-triggered recovery under flow conditions relevant to in vivo use. The paper does not characterize access to external stimulation as the biggest bottleneck. (LLM, conf=0.86)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Also stated in: § Full Text · p. 2 · plain
The sources with a verdict support this claim; the rest weren’t checked yet, have no full text we could read, or their verdicts aren’t rated yet.
In the paper
“It utilizes supramolecular interactions as the molecular switches for the shape transformation.”
What the sources say
- Not checked — no full text of the sourcecites [11] Koerner, H., Price, G., Pearce, N. A., Alexander, M. & Vaia, R. A. Remotely actuated polymer nanocomposites-stress-recovery of carbon-nanotube-filled thermoplastic elastomers. Nat. Mater. 3, 115–120 (2004). source
- Supportedcites [12] Hu, X. et al. Programming temporal shapeshifting. Nat. Commun. 7, 12919 (2016). source
The Abstract says temporary hydrogen bonds regulate energy release and that their reversible reorganization encodes the rate and pathway of shape transformations. The Discussion likewise identifies dynamic bonds as the molecular mechanism of temporal shapeshifting. These reversible interactions support the citing sentence’s description of supramolecular interactions as molecular switches. (LLM, conf=0.91)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“The combination of 3D printing and the on-demand autonomous shape-shifting offers unique advantages beyond other 4D printing systems 26-28 .”
What the sources say
- Not checked — no full text of the sourcecites [26] You, J. et al. Quaternized chitosan/poly(acrylic acid) polyelectrolyte complex hydrogels with tough, self-recovery, and tunable mechanical properties. Macromolecules 49, 1049–1059 (2016). source
- Partly supportedcites [27] Wu, J. et al. Rapid digital light 3D printing enabled by a soft and deformable hydrogel separation interface. Nat. Commun. 12, 6070 (2021). sourceExperimental — accuracy not yet measured
The Results (Resins compatibility; page unavailable) describe a 3D-printed shape-memory rabbit whose programmed shape recovers around 40 °C. The paper does not establish autonomous shape-shifting on demand or advantages over other 4D-printing systems. (LLM, conf=0.84)
- Supportedcites [28] Ding, Z. et al. Direct 4D printing via active composite materials. Sci. Adv. 3, e160289 (2017). source
The Introduction (page not supplied) says the printed component is ready to change shape without the post-printing steps required by other 4D printing approaches, and that it changes rapidly upon heating. The Discussion (page not supplied) describes practical advantages of printing a flat form that subsequently transforms into a 3D structure. The shape change is triggered by heating, rather than occurring without a stimulus. (LLM, conf=0.88)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
39 more claims · 1 with their cited sources checked
Create a free account to see all 66 claims and every source verdict.
- It may state two separate claims as one. 18
- Probably not a substantial claim. 5
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Full Text · p. 4
“Closer monitoring of the shape recovery process (Fig. 4b) clearly shows uniform shape-shifting onset around 10 minutes (Fig. 1c) despite the varied thickness in different parts of the device.”
§ Figures · p. 8
“c, Fabrication process of the shape memory hydrogel.”
Citations
Cites
Printing ferromagnetic domains for untethered fast-transforming soft materials
Kim, Y., Yuk, H., Zhao, R., Chester, S. A., & Zhao, X. (2018) · Nature · doi:10.1038/s41586-018-0185-0 · Cited by 2,183 · cited 8×
“Note that the model was heated to melt the gelatin core, mimicking the soft tissue before testing.”
BackgroundInfluentialFuture perspectives and recent advances in stimuli-responsive materials
Roy, D., Cambre, J. N., & Sumerlin, B. S. (2010) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2009.10.008 · Cited by 1,474 · cited 1×
“Stimulus-responsive shape-shifting polymers 1–3 have shown unique promise in emerging applications, including soft robotics 4–7 , medical devices 8 , aerospace structures 9 and flexible electronics 10 .”
BackgroundTunable polymer multi-shape memory effect
Xie, T. (2010) · Nature · doi:10.1038/nature08863 · Cited by 1,380
Self-citationVoxelated liquid crystal elastomers
Ware, T. H., McConney, M. E., Wie, J. J., Tondiglia, V. P., & White, T. J. (2015) · Science · doi:10.1126/science.1261019 · Cited by 1,157
Making waves in a photoactive polymer film
Gelebart, A. H., Jan Mulder, D., Varga, M., Konya, A., Vantomme, G., Meijer, E. W., Selinger, R. L. B., & Broer, D. J. (2017) · Nature · doi:10.1038/nature22987 · Cited by 1,065
Koerner, H., Price, G., Pearce, N. A., Alexander, M., & Vaia, R. A. (2004) · Nature Materials · doi:10.1038/nmat1059 · Cited by 1,034 · cited 1×
“Here we achieved this goal with a four-dimensional printable shape memory hydrogel that operates via phase separation, with its shape-shifting kinetics dominated by internal mass diffusion rather than by heat transport used for common shape memory polymers 8–11 .”
3D Printing of Shape Memory Polymers for Flexible Electronic Devices
Zarek, M., Layani, M., Cooperstein, I., Sachyani, E., Cohn, D., & Magdassi, S. (2016) · Advanced Materials · doi:10.1002/adma.201503132 · Cited by 903
Direct 4D Printing Via Active Composite Materials
Ding, Z., Yuan, C., Peng, X., Wang, T., Qi, H. J., & Dunn, M. L. (2017) · Science Advances · doi:10.1126/sciadv.1602890 · Cited by 692
Tough Stimuli-Responsive Supramolecular Hydrogels with Hydrogen-Bonding Network Junctions
Guo, M., Pitet, L. M., Wyss, H. M., Vos, M., Dankers, P. Y. W., & Meijer, E. W. (2014) · Journal of the American Chemical Society · doi:10.1021/ja500205v · Cited by 627
Water-driven programmable polyurethane shape memory polymer: Demonstration and mechanism
Huang, W. M., Yang, B., An, L., Li, C., & Chan, Y. S. (2005) · Applied Physics Letters · doi:10.1063/1.1880448 · Cited by 616 · cited 6×
“Non-heating-based natural triggers for either water-15 or degradation-induced 16 SMP are other options.”
BackgroundInfluential
Cited by
Luo, L., Zhang, F., Wang, L., Liu, Y., & Leng, J. (2024) · Advanced Functional Materials · doi:10.1002/adfm.202312036 · Cited by 264
Recent progress in smart electromagnetic interference shielding materials
Hou, X., Feng, X.-R., Jiang, K., Zheng, Y.-C., Liu, J.-T., & Wang, M. (2024) · Journal of Materials Science & Technology · doi:10.1016/j.jmst.2024.01.008 · Cited by 227
Wearable and Implantable Soft Robots
Yin, S., Yao, D. R., Song, Y., Heng, W., Ma, X., Han, H., & Gao, W. (2024) · Chemical Reviews · doi:10.1021/acs.chemrev.4c00513 · Cited by 173
Lu, P., Liao, X., Guo, X., Cai, C., Liu, Y., Chi, M., Du, G., Wei, Z., Meng, X., & Nie, S. (2024) · Nano-Micro Letters · doi:10.1007/s40820-024-01432-2 · Cited by 179
“Owing to these excellent properties, gel materials have been widely utilized in many fields, including environmental management [43–47], flexible sensing [48–50], electrical engineering [51–53], actuators [54–56], and biomedicine [57–64].”
BackgroundBodaghi, M., Wang, L., Zhang, F., Liu, Y., Leng, J., Xing, R., Dickey, M. D., Vanaei, S., Elahinia, M., Hoa, S. V., et al. (2024) · Smart Materials and Structures · doi:10.1088/1361-665x/ad5c22 · Cited by 142
Metadata
- Authors
- Ni, C., Chen, D., Yin, Y., Wen, X., Chen, X., Yang, C., Chen, G., Sun, Z., Wen, J., Jiao, Y., Wang, C., Wang, N., Kong, X., Deng, S., Shen, Y., Xiao, R., Jin, X., Li, J., Kong, X., Zhao, Q., & Xie, T.
- Affiliations
- State Key Laboratory of Chemical Engineering (CN)
- Zhejiang University (CN)
- Second Affiliated Hospital of Zhejiang University (CN)
- State Key Laboratory Fluid Power and Mechatronic Systems (CN)
- Corresponding author
- Zhao, Qian
- Xie, Tao
- ORCID
- Venue
- Nature
- Published
- 2023-09-13
- Volume
- 622
- Issue
- 7984
- Pages
- 748-753
- ISSN
- 0028-0836 (ISSN-L)
- 1476-4687
- OpenAlex
- W4386707773
- Semantic Scholar
- 938360581968e70be64c01950dde4fcd700d2b79
- Cited by
- 397
- References
- 32
- Citations by year
- 2026: 99 · 2025: 166 · 2024: 125 · 2023: 7
- FWCI
- 38.31
- Type
- journal article
- Language
- en
- Open access
- green
- doi.org
- Licence
- cc-by
- www.springernature.com/gp/researchers/text-and-data-mining (tdm)
- www.springernature.com/gp/researchers/text-and-data-mining (vor)
- Locations
- Nature (publishedVersion)
- Research Square (submittedVersion, cc-by)
- PubMed (publishedVersion)
- RePEc: Research Papers in Economics (submittedVersion)
- Funders
- National Natural Science Foundation of China (No. 52033009, 52033009, 51822307, U20A6001)
- Zhejiang University
- State Key Laboratory of Chemical Engineering
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Advanced Materials and Mechanics
- Physical Sciences › Materials Science › Biomaterials › Hydrogels: synthesis, properties, applications
- Physical Sciences › Materials Science › Polymers and Plastics › Polymer composites and self-healing
- Keywords
- shape memory polymers, shape memory hydrogels, 4D printing, spinodal decomposition, mass diffusion, stimuli-responsive materials, soft robotics
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Shape memory polymer with programmable recovery onset. https://app.cochat.ai/papers/10.1038/s41586-023-06520-8
- The paper
- Ni, C., Chen, D., Yin, Y., Wen, X., Chen, X., Yang, C., Chen, G., Sun, Z., Wen, J., Jiao, Y., Wang, C., Wang, N., Kong, X., Deng, S., Shen, Y., Xiao, R., Jin, X., Li, J., Kong, X., . . . Xie, T. (2023). Shape memory polymer with programmable recovery onset. Nature. https://doi.org/10.1038/s41586-023-06520-8
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.