The DOI matches its Crossref record; 68 of the 86 references it cites were found in a registry or an index; 44 of the 50 sources its claims cite were checked for support.
Advanced CMOS manufacturing of superconducting qubits on 300 mm wafers
Open accessAbstract
The development of superconducting qubit technology has shown great potential for the construction of practical quantum computers. Here we demonstrate superconducting transmon qubits manufactured in a 300 mm CMOS pilot line using industrial fabrication methods, with resulting relaxation and coherence times exceeding 100 μs. The presented process uses only optical lithography and reactive-ion etching and has performance and yield in line with conventional laboratory-style techniques.
Overview
CoChat Summary
TL;DR
Superconducting transmon qubits were fabricated on 300 mm silicon wafers in an industrial CMOS pilot line using only optical lithography and reactive-ion etching, with across-wafer yield of 98.25% and time-averaged relaxation/coherence times exceeding 100 μs. The work reports large-scale statistics of coherence, variability, and ageing, identifying capacitor-interface TLS defects as the dominant current limitation.
Key findings
- Out of 400 measured qubits, 393 were functional and fully characterized, giving a yield of 98.25%; the process used 300 mm wafers with 75 dies per wafer and no screening or pre-selection.
- Time-averaged qubit relaxation and Hahn-echo coherence times exceeded 100 μs; best-performing qubits showed T1 = 113 μs near wafer centre, lowest T1 = 42 μs near edge, median T1 = 75 μs, with temporal variation σ ≈ 20 μs and excursions reaching T1 = 161 μs and T2echo = 245 μs.
- Qubit loss scaled linearly with total capacitor interface participation, extrapolating to a T1 limit of approximately milliseconds at 3 GHz; TLS density was estimated at approximately 34 GHz⁻¹, and one fluctuating TLS had a TLF switching rate κ = 0.241 mHz.
- JJ variability analysis gave RSD_RA = 4.47% and σ_A = 0.00334 µm² on a single die; qubit frequency RSD ranged between 5% and 7%; overlap JJ ageing was limited to a 3.7% decrease over 146 days, with process stability verified over at least 151 days.
Methods
- Fabrication: Al/AlOx/Al overlap Josephson junctions on high-resistivity Si, with 70 nm Al bottom electrode, 193 nm optical immersion lithography, Cl-based dry etching, argon milling, regulated dynamic oxidation, and in situ 50 nm Al top electrode; final patterning used optical lithography and dry etching.
- Device designs: one die (24 mm × 28 mm) replicated 75 times on a 300 mm wafer; subdie D1 contained five transmon qubits with four capacitor geometries, and subdie D2 contained ten qubits with identical capacitors and different JJ areas.
- Measurement and analysis: qubits measured at 10 mK in a dilution refrigerator; 32 D1 and 24 D2 subdies characterized across a single wafer, with 400 qubits and 12,840 JJ test structures; 7,872 JJ normal resistances measured with a 300 mm wafer prober; analyses included RSD fitting, interface participation ratio calculations, and TLS density estimation via peak finding.
Limitations
- Stated: TLS density estimation depends on peak-finding algorithm settings, with prominence set to 0.15; JJ area estimates are “best-effort” because of bottom-electrode sidewall tapering and rounded surfaces, and location dependence of area was not included due to insufficient data.
- Stated: insufficient data were available to model the full functional dependence of area variance on bottom/top critical dimensions and bottom-electrode thickness; the hypothesis that weak ageing is due to absence of carbon impurities requires further studies.
- Evident: coherence benchmarking and variability statistics are reported from a single 300 mm wafer, and centre-to-edge gradients remain in T1 and qubit frequency, so batch-to-batch reproducibility is not yet demonstrated in the text.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures








Verification
Claims the paper makes
20 Valid · 2 Not valid · 3 Not checked · 46 Own results and interpretations
Some cited sources support this claim and some don’t — read each source’s verdict below.
In the paper
“However, individual, weakly coupled, TLS defects were spectrally resolved with swap spectroscopy39,49.”
§ Advanced CMOS manufacturing of superconducting qubits on 300 mm wafers > Coherence limitations and interface defects
What the sources say
- Partly supportedcites [39] Klimov, P. V. et al. Fluctuations of energy-relaxation times in superconducting qubits. Phys. Rev. Lett. 121, 090502 (2018). sourceExperimental — accuracy not yet measured
The Text (p. 4) says the authors identified single TLS defects in spectrally resolved qubit T₁ data, and S7 (p. 13) reports measured defect–qubit coupling strengths of 100 kHz to 1 MHz. But the measurement protocol described in the Text (p. 2) is T₁ spectroscopy; our copy does not identify it as swap spectroscopy. (LLM, conf=0.87)
- Disputedcites [49] Carroll, M., Rosenblatt, S., Jurcevic, P., Lauer, I. & Kandala, A. Dynamics of superconducting qubit relaxation times. npj Quantum Inf. 8, 132 (2022). sourceExperimental — accuracy not yet measured
The Introduction and ‘Device and spectroscopy technique’ section say the spectrally resolved features probe strongly coupled TLS, not weakly coupled ones. They describe relaxation-time spectroscopy using AC-Stark shifts and off-resonant microwave tones, rather than swap spectroscopy. Page numbers are unavailable in our copy. (LLM, conf=0.88)
Checked by a reasoning model — may be wrong.
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
Some cited sources support this claim and some don’t — read each source’s verdict below.
In the paper
“Furthermore, the dependence of the Rn RSD on the JJ area fits well with a model of constant area variance (), derived by propagating the uncertainty3,52 (Methods):2”
§ Advanced CMOS manufacturing of superconducting qubits on 300 mm wafers > Qubit frequency variability and ageing
What the sources say
- Partly supportedcites [3] Osman, A. et al. Mitigation of frequency collisions in superconducting quantum processors. Phys. Rev. Res. 5, 043001 (2023). sourceExperimental — accuracy not yet measured
Section II says the relative standard deviation of normal-state resistance was fitted as a function of junction area. But its model uses a constant junction-width variation, σd, with CV_A = 2σd/√A; that implies area variance increases with area, rather than remaining constant. The fit is supported, but the description of its model is not. (LLM, conf=0.87)
- Disputedcites [52] Osman, A. et al. Simplified Josephson-junction fabrication process for reproducibly high-performance superconducting qubits. Appl. Phys. Lett. 118, 064002 (2021). sourceExperimental — accuracy not yet measured
The Qubit passage models the junction side-length standard deviation as constant, not the area variance. It states σ_A = 2dσ_d; because d² = A, this model makes area variance increase with area rather than remain constant. Figure 4’s caption likewise describes a fit using CV_A = 2σ_d/√A. (LLM, conf=0.88)
Checked by a reasoning model — may be wrong.
boostedstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
Every source the paper cites for this claim was checked and supports it.
In the paper
“32 subdies D1 and 24 subdies D2 from across a single 300 mm wafer were measured at 10 mK in a dilution refrigerator (see our previous work30 for set-up details) without being screened or pre-selected.”
§ Advanced CMOS manufacturing of superconducting qubits on 300 mm wafers > Qubit coherence
What the sources say
- Supportedcites [30] Verjauw, J. et al. Path toward manufacturable superconducting qubits with relaxation times exceeding 0.1 ms. npj Quantum Inf. 8, 93 (2022). source
The citation is attached specifically to “set-up details,” not to the counts of subdies or the screening claim. The Qubit measurement setup section describes a dilution-refrigerator setup, including how the sample holder is mounted and thermalized. (LLM, conf=0.91)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Although CMOS foundry-compatible processes26–28 and qubits fabricated partially in a foundry environment29 have been shown previously, the fabrication of 300 nm wafer-scale superconducting qubits has not been demonstrated.”
§ Advanced CMOS manufacturing of superconducting qubits on 300 mm wafers > Main
What the sources say
- Partly supportedcites [26] Wan, D. et al. Fabrication and room temperature characterization of trilayer junctions for the development of superconducting qubits on 300 mm wafers. Jpn. J. Appl. Phys. 60, SBBI04 (2021). sourceExperimental — accuracy not yet measured
The Results and discussion section reports successful fabrication of transmon qubits on 300 mm wafers. The Introduction discusses earlier use of lithography on 300 mm wafers, but the paper does not state that wafer-scale superconducting qubit fabrication had never been demonstrated before this work. (LLM, conf=0.78)
- Could not verifycites [27] Kim, S. et al. Enhanced coherence of all-nitride superconducting qubits epitaxially grown on silicon substrate. Commun. Mater. 2, 98 (2021). sourceExperimental — accuracy not yet measured
The Methods section describes fabricating qubits on Si wafers, but gives no 300 mm wafer size and makes no claim that wafer-scale fabrication had not previously been demonstrated. Searches for “300 mm” and “wafer-scale” found no passage addressing that historical claim. The citing sentence also prints “300 nm,” rather than the claim’s “300 mm.” (LLM, conf=0.76)
- Could not verifycites [28] Anferov, A., Lee, K.-H., Zhao, F., Simon, J. & Schuster, D. I. Improved coherence in optically defined niobium trilayer-junction qubits. Phys. Rev. Appl. 21, 024047 (2024). sourceExperimental — accuracy not yet measured
The Introduction (p. 1) and Conclusion (p. 5) describe optically fabricated niobium qubits, but neither says whether 300 mm wafer-scale superconducting qubits had previously been demonstrated. A search for 300 mm wafer-scale fabrication and foundry processes found no passage addressing that historical claim; Appendix A (pp. 5–6) describes wafers without specifying a 300 mm scale. (LLM, conf=0.75)
- Partly supportedcites [29] Foroozani, N. et al. Development of transmon qubits solely from optical lithography on 300 mm wafers. Quantum Sci. Technol. 4, 025012 (2019). sourceExperimental — accuracy not yet measured
The Introduction (page unavailable) calls this the first report of transmon qubits patterned solely with optical lithography on 300 mm wafers. That supports the narrower novelty claim, but does not establish that no superconducting qubits had previously been fabricated on 300 mm wafers using other methods. (LLM, conf=0.82)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“These relaxation channels are probably weakly coupled TLS defects at the capacitor interfaces, where the electric fields were orders of magnitude lower than inside the JJ3,50.”
§ Advanced CMOS manufacturing of superconducting qubits on 300 mm wafers > Coherence limitations and interface defects
What the sources say
- Partly supportedcites [3] Osman, A. et al. Mitigation of frequency collisions in superconducting quantum processors. Phys. Rev. Res. 5, 043001 (2023). sourceExperimental — accuracy not yet measured
Section IV reports frequency-resolved relaxation peaks attributed to TLSs and says the narrower peaks are signatures of TLSs in the oxide surrounding the qubit electrodes, rather than in the JJ tunnel barrier. Appendix C discusses sensitivity to weakly coupled TLSs. The copy does not specifically locate these defects at capacitor interfaces or state that electric fields there were orders of magnitude lower than inside the JJ. (LLM, conf=0.86)
- Partly supportedcites [50] Barends, R. et al. Coherent Josephson qubit suitable for scalable quantum integrated circuits. Phys. Rev. Lett. 111, 080502 (2013). sourceExperimental — accuracy not yet measured
The main text (p. 4) attributes peaks in energy decay to incoherent two-level defects near capacitor metal edges, and the Monte Carlo section (p. 9) places defects at capacitor interfaces. Our copy does not state that electric fields there were orders of magnitude lower than inside the Josephson junction; that comparison is unsupported. (LLM, conf=0.88)
hedgedstates a possible cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
34 more claims · 2 with their cited sources checked
Create a free account to see all 71 claims and to verify the 3 references still open.
- It may state two separate claims as one. 19
- Probably not a substantial claim. 13
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Advanced CMOS manufacturing of superconducting qubits on 300 mm wafers > Main
“the fabrication of 300 nm wafer-scale superconducting qubits has not been demonstrated.”
§ Advanced CMOS manufacturing of superconducting qubits on 300 mm wafers > Main
“we demonstrate superconducting transmon qubits fabricated on 300 mm silicon wafers”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Advanced CMOS manufacturing of superconducting qubits on 300 mm wafers > Design and fabrication
“which was replicated 75 times to constitute the complete 300-mm-diameter wafer”
§ Advanced CMOS manufacturing of superconducting qubits on 300 mm wafers > Qubit frequency variability and ageing
“8 (JJs per area per die) × 12 (areas) × 82 (dies) = 7,872 JJs across a wafer”
Citations
Cites
Quantum supremacy using a programmable superconducting processor
Arute, F., Arya, K., Babbush, R., Bacon, D., Bardin, J. C., Barends, R., Biswas, R., Boixo, S., Brandao, F. G. S. L., Buell, D. A., et al. (2019) · Nature · doi:10.1038/s41586-019-1666-5 · Cited by 7,720 · cited 1×
“We show across-wafer, large-scale statistics of coherence, yield, variability and ageing that confirm the validity of our approach.”
ResultCharge-insensitive qubit design derived from the Cooper pair box
Koch, J., Yu, T. M., Gambetta, J., Houck, A. A., Schuster, D. I., Majer, J., Blais, A., Devoret, M. H., Girvin, S. M., & Schoelkopf, R. J. (2007) · Physical Review A · doi:10.1103/physreva.76.042319 · Cited by 3,351 · cited 2×
“The presented industry-scale fabrication process, which uses only optical lithography and reactive-ion etching, has a performance and yield in line with conventional laboratory-style techniques utilizing metal lift-off, angled evaporation and electron-beam writing 4 .”
BackgroundMethodTunneling Between Superconductors
Ambegaokar, V., & Baratoff, A. (1963) · Physical Review Letters · doi:10.1103/physrevlett.10.486 · Cited by 2,195
Suppressing quantum errors by scaling a surface code logical qubit
Google Quantum, A. I., Acharya, R., Aleiner, I., Allen, R., Andersen, T. I., Ansmann, M., Arute, F., Arya, K., Asfaw, A., Atalaya, J., et al. (2023) · Nature · doi:10.1038/s41586-022-05434-1 · Cited by 1,103
Self-citationEvidence for the utility of quantum computing before fault tolerance
Kim, Y., Eddins, A., Anand, S., Wei, K. X., van den Berg, E., Rosenblatt, S., Nayfeh, H., Wu, Y., Zaletel, M., Temme, K., et al. (2023) · Nature · doi:10.1038/s41586-023-06096-3 · Cited by 1,050 · cited 2×
“The development of superconducting qubit technology has shown great potential for the construction of practical quantum computers 1,2 .”
BackgroundPhillips, W. A. (1987) · Reports on Progress in Physics · doi:10.1088/0034-4885/50/12/003 · Cited by 885 · cited 1×
“Such temporal fluctuations are associated with coupling of the qubit to near-resonance two-level system (TLS) defects 37 , which are, in turn, longitudinally coupled to low-frequency (thermally active at 10 mK) two-level fluctuators (TLFs) 35,38,39 .”
BackgroundDecoherence in Josephson Qubits from Dielectric Loss
Martinis, J. M., Cooper, K. B., McDermott, R., Steffen, M., Ansmann, M., Osborn, K. D., Cicak, K., Oh, S., Pappas, D. P., Simmonds, R. W., et al. (2005) · Physical Review Letters · doi:10.1103/physrevlett.95.210503 · Cited by 838 · cited 1×
“To gain insight into the coupled TLS defects, a magnetic-flux-tunable qubit on a subdie D2 was used to scan the spectral environment.”
MethodCoherent Josephson Qubit Suitable for Scalable Quantum Integrated Circuits
Barends, R., Kelly, J., Megrant, A., Sank, D., Jeffrey, E., Chen, Y., Yin, Y., Chiaro, B., Mutus, J., Neill, C., et al. (2013) · Physical Review Letters · doi:10.1103/physrevlett.111.080502 · Cited by 779 · cited 1×
“The resulting time–frequency map of the residual qubit population, visualized by Fig.”
BackgroundMaterials challenges and opportunities for quantum computing hardware
de Leon, N. P., Itoh, K. M., Kim, D., Mehta, K. K., Northup, T. E., Paik, H., Palmer, B. S., Samarth, N., Sangtawesin, S., & Steuerman, D. W. (2021) · Science · doi:10.1126/science.abb2823 · Cited by 710 · cited 6×
“Here we demonstrate superconducting transmon qubits manufactured in a 300 mm complementary metal–oxide–semiconductor (CMOS) pilot line using industrial fabrication methods, with resulting relaxation and coherence times exceeding 100 μs.”
BackgroundMethodInfluentialRealizing repeated quantum error correction in a distance-three surface code
Krinner, S., Lacroix, N., Remm, A., Di Paolo, A., Genois, E., Leroux, C., Hellings, C., Lazar, S., Swiadek, F., Herrmann, J., et al. (2022) · Nature · doi:10.1038/s41586-022-04566-8 · Cited by 686
Cited by
Tuokkola, M., Sunada, Y., Kivijärvi, H., Albanese, J., Grönberg, L., Kaikkonen, J.-P., Vesterinen, V., Govenius, J., & Möttönen, M. (2025) · Nature Communications · doi:10.1038/s41467-025-61126-0 · Cited by 132
Millisecond lifetimes and coherence times in 2D transmon qubits
Bland, M. P., Bahrami, F., Martinez, J. G. C., Prestegaard, P. H., Smitham, B. M., Joshi, A., Hedrick, E., Kumar, S., Yang, A., Pakpour‐Tabrizi, A. C., et al. (2025) · Nature · doi:10.1038/s41586-025-09687-4 · Cited by 204
Quantum Batteries: A Materials Science Perspective
Camposeo, A., Virgili, T., Lombardi, F., Cerullo, G., Pisignano, D., & Polini, M. (2025) · Advanced Materials · doi:10.1002/adma.202415073 · Cited by 50
Advancements in superconducting quantum computing
Jiang, Y.-Y., Deng, C., Fan, H., Li, B.-Y., Sun, L., Tan, X., Wang, W., Xue, G., Yan, F., Yu, H., et al. (2025) · National Science Review · doi:10.1093/nsr/nwaf246 · Cited by 83
“Future advancements, including industry-standard fabrication and leveraging semiconductor manufacturing facilities [47 ], aim to enhance yield, parameter control and coherence times, potentially exceeding the mi l lisecond level for very large-scale quantum processors.”
Zhang, G., Fan, X., Wang, Z., Li, P., Zhang, Z., Yu, B., Gao, D., Loke, D. K., Zhong, S., Wan, Q., et al. (2026) · Nano-Micro Letters · doi:10.1007/s40820-025-02035-1 · Cited by 19
Metadata
- Authors
- Van Damme, J., Massar, S., Acharya, R., Ivanov, T., Perez Lozano, D., Canvel, Y., Demarets, M., Vangoidsenhoven, D., Hermans, Y., Lai, J. G., Vadiraj, A. M., Mongillo, M., Wan, D., De Boeck, J., Potočnik, A., & De Greve, K.
- Affiliations
- IMEC (BE)
- Corresponding author
- Potočnik, A.
- Venue
- Nature
- Published
- 2024-09-18
- Volume
- 634
- Issue
- 8032
- Pages
- 74-79
- ISSN
- 0028-0836 (ISSN-L)
- 1476-4687
- PMC
- PMC11446867
- OpenAlex
- W4402585749
- Cited by
- 63
- References
- 86
- Citations by year
- 2026: 29 · 2025: 32 · 2024: 2
- FWCI
- 6.89
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Licence
- cc-by
- creativecommons.org/licenses/by/4.0 (tdm)
- creativecommons.org/licenses/by/4.0 (vor)
- Locations
- Nature (publishedVersion, cc-by)
- PubMed (publishedVersion)
- arXiv (Cornell University) (submittedVersion, cc-by-nc-nd)
- Lirias (submittedVersion, cc-by)
- PubMed Central (submittedVersion, cc-by)
- arXiv (Cornell University)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advancements in Semiconductor Devices and Circuit Design
- Physical Sciences › Computer Science › Artificial Intelligence › Quantum Computing Algorithms and Architecture
- Physical Sciences › Computer Science › Computational Theory and Mathematics › Quantum-Dot Cellular Automata
- Keywords
- superconducting qubits, transmon qubits, CMOS-compatible fabrication, 300 mm wafers, coherence time, relaxation time, fabrication yield, device variability
- MeSH terms
- Superconductivity, Metals, Oxides, Quantum Theory, Semiconductors
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Advanced CMOS manufacturing of superconducting qubits on 300 mm wafers. https://app.cochat.ai/papers/10.1038/s41586-024-07941-9
- The paper
- Van Damme, J., Massar, S., Acharya, R., Ivanov, T., Perez Lozano, D., Canvel, Y., Demarets, M., Vangoidsenhoven, D., Hermans, Y., Lai, J. G., Vadiraj, A. M., Mongillo, M., Wan, D., De Boeck, J., Potočnik, A., & De Greve, K. (2024). Advanced CMOS manufacturing of superconducting qubits on 300 mm wafers. Nature. https://doi.org/10.1038/s41586-024-07941-9
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.