The DOI matches its Crossref record; 68 of the 86 references it cites were found in a registry or an index; 44 of the 50 sources its claims cite were checked for support.
Advanced CMOS manufacturing of superconducting qubits on 300 mm wafers
Open accessAbstract
The development of superconducting qubit technology has shown great potential for the construction of practical quantum computers. Here we demonstrate superconducting transmon qubits manufactured in a 300 mm CMOS pilot line using industrial fabrication methods, with resulting relaxation and coherence times exceeding 100 μs. The presented process uses only optical lithography and reactive-ion etching and has performance and yield in line with conventional laboratory-style techniques.
Overview
CoChat Summary
TL;DR
Superconducting transmon qubits were fabricated on 300 mm silicon wafers in an industrial CMOS pilot line using only optical lithography and reactive-ion etching, with across-wafer yield of 98.25% and time-averaged relaxation/coherence times exceeding 100 μs. The work reports large-scale statistics of coherence, variability, and ageing, identifying capacitor-interface TLS defects as the dominant current limitation.
Key findings
- Out of 400 measured qubits, 393 were functional and fully characterized, giving a yield of 98.25%; the process used 300 mm wafers with 75 dies per wafer and no screening or pre-selection.
- Time-averaged qubit relaxation and Hahn-echo coherence times exceeded 100 μs; best-performing qubits showed T1 = 113 μs near wafer centre, lowest T1 = 42 μs near edge, median T1 = 75 μs, with temporal variation σ ≈ 20 μs and excursions reaching T1 = 161 μs and T2echo = 245 μs.
- Qubit loss scaled linearly with total capacitor interface participation, extrapolating to a T1 limit of approximately milliseconds at 3 GHz; TLS density was estimated at approximately 34 GHz⁻¹, and one fluctuating TLS had a TLF switching rate κ = 0.241 mHz.
- JJ variability analysis gave RSD_RA = 4.47% and σ_A = 0.00334 µm² on a single die; qubit frequency RSD ranged between 5% and 7%; overlap JJ ageing was limited to a 3.7% decrease over 146 days, with process stability verified over at least 151 days.
Methods
- Fabrication: Al/AlOx/Al overlap Josephson junctions on high-resistivity Si, with 70 nm Al bottom electrode, 193 nm optical immersion lithography, Cl-based dry etching, argon milling, regulated dynamic oxidation, and in situ 50 nm Al top electrode; final patterning used optical lithography and dry etching.
- Device designs: one die (24 mm × 28 mm) replicated 75 times on a 300 mm wafer; subdie D1 contained five transmon qubits with four capacitor geometries, and subdie D2 contained ten qubits with identical capacitors and different JJ areas.
- Measurement and analysis: qubits measured at 10 mK in a dilution refrigerator; 32 D1 and 24 D2 subdies characterized across a single wafer, with 400 qubits and 12,840 JJ test structures; 7,872 JJ normal resistances measured with a 300 mm wafer prober; analyses included RSD fitting, interface participation ratio calculations, and TLS density estimation via peak finding.
Limitations
- Stated: TLS density estimation depends on peak-finding algorithm settings, with prominence set to 0.15; JJ area estimates are “best-effort” because of bottom-electrode sidewall tapering and rounded surfaces, and location dependence of area was not included due to insufficient data.
- Stated: insufficient data were available to model the full functional dependence of area variance on bottom/top critical dimensions and bottom-electrode thickness; the hypothesis that weak ageing is due to absence of carbon impurities requires further studies.
- Evident: coherence benchmarking and variability statistics are reported from a single 300 mm wafer, and centre-to-edge gradients remain in T1 and qubit frequency, so batch-to-batch reproducibility is not yet demonstrated in the text.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures








Verification
Claims the paper makes
20 Valid · 2 Not valid · 3 Not checked · 46 Own results and interpretations
Some cited sources support this claim and some don’t — read each source’s verdict below.
In the paper
“However, individual, weakly coupled, TLS defects were spectrally resolved with swap spectroscopy39,49.”
§ Advanced CMOS manufacturing of superconducting qubits on 300 mm wafers > Coherence limitations and interface defects
What the sources say
- Partly supportedcites [39] Klimov, P. V. et al. Fluctuations of energy-relaxation times in superconducting qubits. Phys. Rev. Lett. 121, 090502 (2018). sourceExperimental — accuracy not yet measured
The Text (p. 4) says the authors identified single TLS defects in spectrally resolved qubit T₁ data, and S7 (p. 13) reports measured defect–qubit coupling strengths of 100 kHz to 1 MHz. But the measurement protocol described in the Text (p. 2) is T₁ spectroscopy; our copy does not identify it as swap spectroscopy. (LLM, conf=0.87)
- Disputedcites [49] Carroll, M., Rosenblatt, S., Jurcevic, P., Lauer, I. & Kandala, A. Dynamics of superconducting qubit relaxation times. npj Quantum Inf. 8, 132 (2022). sourceExperimental — accuracy not yet measured
The Introduction and ‘Device and spectroscopy technique’ section say the spectrally resolved features probe strongly coupled TLS, not weakly coupled ones. They describe relaxation-time spectroscopy using AC-Stark shifts and off-resonant microwave tones, rather than swap spectroscopy. Page numbers are unavailable in our copy. (LLM, conf=0.88)
Checked by a reasoning model — may be wrong.
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
Some cited sources support this claim and some don’t — read each source’s verdict below.
In the paper
“Furthermore, the dependence of the Rn RSD on the JJ area fits well with a model of constant area variance (), derived by propagating the uncertainty3,52 (Methods):2”
§ Advanced CMOS manufacturing of superconducting qubits on 300 mm wafers > Qubit frequency variability and ageing
What the sources say
- Partly supportedcites [3] Osman, A. et al. Mitigation of frequency collisions in superconducting quantum processors. Phys. Rev. Res. 5, 043001 (2023). sourceExperimental — accuracy not yet measured
Section II says the relative standard deviation of normal-state resistance was fitted as a function of junction area. But its model uses a constant junction-width variation, σd, with CV_A = 2σd/√A; that implies area variance increases with area, rather than remaining constant. The fit is supported, but the description of its model is not. (LLM, conf=0.87)
- Disputedcites [52] Osman, A. et al. Simplified Josephson-junction fabrication process for reproducibly high-performance superconducting qubits. Appl. Phys. Lett. 118, 064002 (2021). sourceExperimental — accuracy not yet measured
The Qubit passage models the junction side-length standard deviation as constant, not the area variance. It states σ_A = 2dσ_d; because d² = A, this model makes area variance increase with area rather than remain constant. Figure 4’s caption likewise describes a fit using CV_A = 2σ_d/√A. (LLM, conf=0.88)
Checked by a reasoning model — may be wrong.
boostedstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
Every source the paper cites for this claim was checked and supports it.
In the paper
“32 subdies D1 and 24 subdies D2 from across a single 300 mm wafer were measured at 10 mK in a dilution refrigerator (see our previous work30 for set-up details) without being screened or pre-selected.”
§ Advanced CMOS manufacturing of superconducting qubits on 300 mm wafers > Qubit coherence
What the sources say
- Supportedcites [30] Verjauw, J. et al. Path toward manufacturable superconducting qubits with relaxation times exceeding 0.1 ms. npj Quantum Inf. 8, 93 (2022). source
The citation is attached specifically to “set-up details,” not to the counts of subdies or the screening claim. The Qubit measurement setup section describes a dilution-refrigerator setup, including how the sample holder is mounted and thermalized. (LLM, conf=0.91)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Although CMOS foundry-compatible processes26–28 and qubits fabricated partially in a foundry environment29 have been shown previously, the fabrication of 300 nm wafer-scale superconducting qubits has not been demonstrated.”
§ Advanced CMOS manufacturing of superconducting qubits on 300 mm wafers > Main
What the sources say
- Partly supportedcites [26] Wan, D. et al. Fabrication and room temperature characterization of trilayer junctions for the development of superconducting qubits on 300 mm wafers. Jpn. J. Appl. Phys. 60, SBBI04 (2021). sourceExperimental — accuracy not yet measured
The Results and discussion section reports successful fabrication of transmon qubits on 300 mm wafers. The Introduction discusses earlier use of lithography on 300 mm wafers, but the paper does not state that wafer-scale superconducting qubit fabrication had never been demonstrated before this work. (LLM, conf=0.78)
- Could not verifycites [27] Kim, S. et al. Enhanced coherence of all-nitride superconducting qubits epitaxially grown on silicon substrate. Commun. Mater. 2, 98 (2021). sourceExperimental — accuracy not yet measured
The Methods section describes fabricating qubits on Si wafers, but gives no 300 mm wafer size and makes no claim that wafer-scale fabrication had not previously been demonstrated. Searches for “300 mm” and “wafer-scale” found no passage addressing that historical claim. The citing sentence also prints “300 nm,” rather than the claim’s “300 mm.” (LLM, conf=0.76)
- Could not verifycites [28] Anferov, A., Lee, K.-H., Zhao, F., Simon, J. & Schuster, D. I. Improved coherence in optically defined niobium trilayer-junction qubits. Phys. Rev. Appl. 21, 024047 (2024). sourceExperimental — accuracy not yet measured
The Introduction (p. 1) and Conclusion (p. 5) describe optically fabricated niobium qubits, but neither says whether 300 mm wafer-scale superconducting qubits had previously been demonstrated. A search for 300 mm wafer-scale fabrication and foundry processes found no passage addressing that historical claim; Appendix A (pp. 5–6) describes wafers without specifying a 300 mm scale. (LLM, conf=0.75)
- Partly supportedcites [29] Foroozani, N. et al. Development of transmon qubits solely from optical lithography on 300 mm wafers. Quantum Sci. Technol. 4, 025012 (2019). sourceExperimental — accuracy not yet measured
The Introduction (page unavailable) calls this the first report of transmon qubits patterned solely with optical lithography on 300 mm wafers. That supports the narrower novelty claim, but does not establish that no superconducting qubits had previously been fabricated on 300 mm wafers using other methods. (LLM, conf=0.82)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“These relaxation channels are probably weakly coupled TLS defects at the capacitor interfaces, where the electric fields were orders of magnitude lower than inside the JJ3,50.”
§ Advanced CMOS manufacturing of superconducting qubits on 300 mm wafers > Coherence limitations and interface defects
What the sources say
- Partly supportedcites [3] Osman, A. et al. Mitigation of frequency collisions in superconducting quantum processors. Phys. Rev. Res. 5, 043001 (2023). sourceExperimental — accuracy not yet measured
Section IV reports frequency-resolved relaxation peaks attributed to TLSs and says the narrower peaks are signatures of TLSs in the oxide surrounding the qubit electrodes, rather than in the JJ tunnel barrier. Appendix C discusses sensitivity to weakly coupled TLSs. The copy does not specifically locate these defects at capacitor interfaces or state that electric fields there were orders of magnitude lower than inside the JJ. (LLM, conf=0.86)
- Partly supportedcites [50] Barends, R. et al. Coherent Josephson qubit suitable for scalable quantum integrated circuits. Phys. Rev. Lett. 111, 080502 (2013). sourceExperimental — accuracy not yet measured
The main text (p. 4) attributes peaks in energy decay to incoherent two-level defects near capacitor metal edges, and the Monte Carlo section (p. 9) places defects at capacitor interfaces. Our copy does not state that electric fields there were orders of magnitude lower than inside the Josephson junction; that comparison is unsupported. (LLM, conf=0.88)
hedgedstates a possible cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
34 more claims · 2 with their cited sources checked
Create a free account to see all 71 claims and to verify the 3 references still open.
- It may state two separate claims as one. 19
- Probably not a substantial claim. 13
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Advanced CMOS manufacturing of superconducting qubits on 300 mm wafers > Main
“the fabrication of 300 nm wafer-scale superconducting qubits has not been demonstrated.”
§ Advanced CMOS manufacturing of superconducting qubits on 300 mm wafers > Main
“we demonstrate superconducting transmon qubits fabricated on 300 mm silicon wafers”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Advanced CMOS manufacturing of superconducting qubits on 300 mm wafers > Design and fabrication
“which was replicated 75 times to constitute the complete 300-mm-diameter wafer”
§ Advanced CMOS manufacturing of superconducting qubits on 300 mm wafers > Qubit frequency variability and ageing
“8 (JJs per area per die) × 12 (areas) × 82 (dies) = 7,872 JJs across a wafer”
Citations
Cites
Quantum supremacy using a programmable superconducting processor
Arute, F., Arya, K., Babbush, R., Bacon, D., Bardin, J. C., Barends, R., Biswas, R., Boixo, S., Brandao, F. G. S. L., Buell, D. A., et al. (2019) · Nature · doi:10.1038/s41586-019-1666-5 · Cited by 7,720 · cited 1×
“We show across-wafer, large-scale statistics of coherence, yield, variability and ageing that confirm the validity of our approach.”
ResultCharge-insensitive qubit design derived from the Cooper pair box
Koch, J., Yu, T. M., Gambetta, J., Houck, A. A., Schuster, D. I., Majer, J., Blais, A., Devoret, M. H., Girvin, S. M., & Schoelkopf, R. J. (2007) · Physical Review A · doi:10.1103/physreva.76.042319 · Cited by 3,351 · cited 2×
“The presented industry-scale fabrication process, which uses only optical lithography and reactive-ion etching, has a performance and yield in line with conventional laboratory-style techniques utilizing metal lift-off, angled evaporation and electron-beam writing 4 .”
BackgroundMethodTunneling Between Superconductors
Ambegaokar, V., & Baratoff, A. (1963) · Physical Review Letters · doi:10.1103/physrevlett.10.486 · Cited by 2,195
Suppressing quantum errors by scaling a surface code logical qubit
Google Quantum, A. I., Acharya, R., Aleiner, I., Allen, R., Andersen, T. I., Ansmann, M., Arute, F., Arya, K., Asfaw, A., Atalaya, J., et al. (2023) · Nature · doi:10.1038/s41586-022-05434-1 · Cited by 1,103
Self-citationEvidence for the utility of quantum computing before fault tolerance
Kim, Y., Eddins, A., Anand, S., Wei, K. X., van den Berg, E., Rosenblatt, S., Nayfeh, H., Wu, Y., Zaletel, M., Temme, K., et al. (2023) · Nature · doi:10.1038/s41586-023-06096-3 · Cited by 1,050 · cited 2×
“The development of superconducting qubit technology has shown great potential for the construction of practical quantum computers 1,2 .”
BackgroundPhillips, W. A. (1987) · Reports on Progress in Physics · doi:10.1088/0034-4885/50/12/003 · Cited by 885 · cited 1×
“Such temporal fluctuations are associated with coupling of the qubit to near-resonance two-level system (TLS) defects 37 , which are, in turn, longitudinally coupled to low-frequency (thermally active at 10 mK) two-level fluctuators (TLFs) 35,38,39 .”
BackgroundDecoherence in Josephson Qubits from Dielectric Loss
Martinis, J. M., Cooper, K. B., McDermott, R., Steffen, M., Ansmann, M., Osborn, K. D., Cicak, K., Oh, S., Pappas, D. P., Simmonds, R. W., et al. (2005) · Physical Review Letters · doi:10.1103/physrevlett.95.210503 · Cited by 838 · cited 1×
“To gain insight into the coupled TLS defects, a magnetic-flux-tunable qubit on a subdie D2 was used to scan the spectral environment.”
MethodCoherent Josephson Qubit Suitable for Scalable Quantum Integrated Circuits
Barends, R., Kelly, J., Megrant, A., Sank, D., Jeffrey, E., Chen, Y., Yin, Y., Chiaro, B., Mutus, J., Neill, C., et al. (2013) · Physical Review Letters · doi:10.1103/physrevlett.111.080502 · Cited by 779 · cited 1×
“The resulting time–frequency map of the residual qubit population, visualized by Fig.”
BackgroundMaterials challenges and opportunities for quantum computing hardware
de Leon, N. P., Itoh, K. M., Kim, D., Mehta, K. K., Northup, T. E., Paik, H., Palmer, B. S., Samarth, N., Sangtawesin, S., & Steuerman, D. W. (2021) · Science · doi:10.1126/science.abb2823 · Cited by 710 · cited 6×
“Here we demonstrate superconducting transmon qubits manufactured in a 300 mm complementary metal–oxide–semiconductor (CMOS) pilot line using industrial fabrication methods, with resulting relaxation and coherence times exceeding 100 μs.”
BackgroundMethodInfluentialRealizing repeated quantum error correction in a distance-three surface code
Krinner, S., Lacroix, N., Remm, A., Di Paolo, A., Genois, E., Leroux, C., Hellings, C., Lazar, S., Swiadek, F., Herrmann, J., et al. (2022) · Nature · doi:10.1038/s41586-022-04566-8 · Cited by 686
Place, A. P. M., Rodgers, L. V. H., Mundada, P., Smitham, B. M., Fitzpatrick, M., Leng, Z., Premkumar, A., Bryon, J., Vrajitoarea, A., Sussman, S., et al. (2021) · Nature Communications · doi:10.1038/s41467-021-22030-5 · Cited by 563 · cited 1×
“The advantage of this fabrication technique is the possibility for in situ fabrication of the JJ and minimal etch damage to achieve high-coherence qubits of up to hundreds of microseconds 19–22 .”
MethodHigh-threshold and low-overhead fault-tolerant quantum memory
Bravyi, S., Cross, A. W., Gambetta, J. M., Maslov, D., Rall, P., & Yoder, T. J. (2024) · Nature · doi:10.1038/s41586-024-07107-7 · Cited by 456 · cited 1×
“Advances in error-correcting codes 6 and quantum gate fidelities could reduce the required number of physical qubits.”
BackgroundDecoherence benchmarking of superconducting qubits
Burnett, J. J., Bengtsson, A., Scigliuzzo, M., Niepce, D., Kudra, M., Delsing, P., & Bylander, J. (2019) · npj Quantum Information · doi:10.1038/s41534-019-0168-5 · Cited by 384 · cited 2×
“The frequency noise power spectral density of the TLS was fitted well with a single random TLF model characterized by a Lorentzian with a TLF random switching rate ( κ ) of 0.241 mHz, comparable to timescales of previously reported relaxation time fluctuations 36 .”
BackgroundMethodInfluentialTowards practical quantum computers: transmon qubit with a lifetime approaching 0.5 milliseconds
Wang, C., Li, X., Xu, H., Li, Z., Wang, J., Yang, Z., Mi, Z., Liang, X., Su, T., Yang, C., et al. (2022) · npj Quantum Information · doi:10.1038/s41534-021-00510-2 · Cited by 377
Qubits made by advanced semiconductor manufacturing
Zwerver, A. M. J., Krähenmann, T., Watson, T. F., Lampert, L., George, H. C., Pillarisetty, R., Bojarski, S. A., Amin, P., Amitonov, S. V., Boter, J. M., et al. (2022) · Nature Electronics · doi:10.1038/s41928-022-00727-9 · Cited by 364 · cited 1×
“…lithography and reactive-ion etching of 300-mm-diameter wafers is an attractive alternative, as it could fully leverage the state of the art in advanced complementary metal–oxide–semiconductor (CMOS) fabrication, in line with recent developments in silicon quantum-dot qubit fabrication 23,24 .”
BackgroundFluctuations of Energy-Relaxation Times in Superconducting Qubits
Klimov, P. V., Kelly, J., Chen, Z., Neeley, M., Megrant, A., Burkett, B., Barends, R., Arya, K., Chiaro, B., Chen, Y., et al. (2018) · Physical Review Letters · doi:10.1103/physrevlett.121.090502 · Cited by 328 · cited 3×
“The absence of a concurrent jump in T 1 indicates that the most plausible explanation is the vanishing of a coupled TLF (and not a near-resonant TLS), possibly due to a defect rearrangement from an impinging high-energy radiation event 40 or due to a trapped quasiparticle escaping from a shallow,…”
BackgroundRealization of an Error-Correcting Surface Code with Superconducting Qubits
Zhao, Y., Ye, Y., Huang, H.-L., Zhang, Y., Wu, D., Guan, H., Zhu, Q., Wei, Z., He, T., Cao, S., et al. (2022) · Physical Review Letters · doi:10.1103/physrevlett.129.030501 · Cited by 321 · cited 1×
“Here we demonstrate superconducting transmon qubits manufactured in a 300 mm complementary metal–oxide–semiconductor (CMOS) pilot line using industrial fabrication methods, with resulting relaxation and coherence times exceeding 100 μs.”
MethodEngineering high-coherence superconducting qubits
Siddiqi, I. (2021) · Nature Reviews Materials · doi:10.1038/s41578-021-00370-4 · Cited by 311 · cited 1×
“Superconducting circuit implementations of quantum bits have leveraged the scalable nature of solid-state fabrication and have shown tremendous progress in terms of qubit coherence times 4,8 and gate fidelities 9 .”
BackgroundSystematic improvements in transmon qubit coherence enabled by niobium surface encapsulation
Bal, M., Murthy, A. A., Zhu, S., Crisa, F., You, X., Huang, Z., Roy, T., Lee, J., van Zanten, D. M. T., Pilipenko, R., et al. (2024) · npj Quantum Information · doi:10.1038/s41534-024-00840-x · Cited by 212 · cited 1×
“Interface engineering techniques with metal seed layers or metal encapsulation 45 may improve this process.”
BackgroundCorrelating Decoherence in Transmon Qubits: Low Frequency Noise by Single Fluctuators
Schlör, S., Lisenfeld, J., Müller, C., Bilmes, A., Schneider, A., Pappas, D. P., Ustinov, A. V., & Weides, M. (2019) · Physical Review Letters · doi:10.1103/physrevlett.123.190502 · Cited by 209 · cited 3×
“The absence of a concurrent jump in T 1 indicates that the most plausible explanation is the vanishing of a coupled TLF (and not a near-resonant TLS), possibly due to a defect rearrangement from an impinging high-energy radiation event 40 or due to a trapped quasiparticle escaping from a shallow,…”
BackgroundLaser-annealing Josephson junctions for yielding scaled-up superconducting quantum processors
Hertzberg, J. B., Zhang, E. J., Rosenblatt, S., Magesan, E., Smolin, J. A., Yau, J.-B., Adiga, V. P., Sandberg, M., Brink, M., Chow, J. M., et al. (2021) · npj Quantum Information · doi:10.1038/s41534-021-00464-5 · Cited by 198
High-Fidelity, Frequency-Flexible Two-Qubit Fluxonium Gates with a Transmon Coupler
Ding, L., Hays, M., Sung, Y., Kannan, B., An, J., Paolo, A. D., Karamlou, A. H., Hazard, T., Azar, K., Kim, D. K., et al. (2023) · Physical Review X · doi:10.1103/physrevx.13.031035 · Cited by 180 · cited 1×
“Here we demonstrate superconducting transmon qubits manufactured in a 300 mm complementary metal–oxide–semiconductor (CMOS) pilot line using industrial fabrication methods, with resulting relaxation and coherence times exceeding 100 μs.”
MethodProbing single electrons across 300-mm spin qubit wafers
Neyens, S., Zietz, O. K., Watson, T. F., Luthi, F., Nethwewala, A., George, H. C., Henry, E., Islam, M., Wagner, A. J., Borjans, F., et al. (2024) · Nature · doi:10.1038/s41586-024-07275-6 · Cited by 178 · cited 2×
“…lithography and reactive-ion etching of 300-mm-diameter wafers is an attractive alternative, as it could fully leverage the state of the art in advanced complementary metal–oxide–semiconductor (CMOS) fabrication, in line with recent developments in silicon quantum-dot qubit fabrication 23,24 .”
BackgroundMethodBeating the break-even point with a discrete-variable-encoded logical qubit
Ni, Z., Li, S., Deng, X., Cai, Y., Zhang, L., Wang, W., Yang, Z.-B., Yu, H., Yan, F., Liu, S., et al. (2023) · Nature · doi:10.1038/s41586-023-05784-4 · Cited by 176 · cited 1×
“The substrate–air, metal–air and substrate–metal interface participation ratios were calculated for the four different capacitor geometries (width and gap in {13, 24, 48, 90} μm).”
MethodChallenges and recent prospectives of 3D heterogeneous integration
Zhang, S., Li, Z., Zhou, H., Li, R., Wang, S., Paik, K., & He, P. (2022) · e-Prime - Advances in Electrical Engineering Electronics and Energy · doi:10.1016/j.prime.2022.100052 · Cited by 165 · cited 1×
“This is especially true in view of the enormous sophistication and process control achievable in modern industrial semiconductor tooling sets, as well as the knowledge of advanced three-dimensional integration techniques developed for 300-mm-diameter wafers in the pursuit of Moore’s law 25 .”
BackgroundDetermining Interface Dielectric Losses in Superconducting Coplanar-Waveguide Resonators
Woods, W., Calusine, G., Melville, A., Sevi, A., Golden, E., Kim, D. K., Rosenberg, D., Yoder, J. L., & Oliver, W. D. (2019) · Physical Review Applied · doi:10.1103/physrevapplied.12.014012 · Cited by 164 · cited 1×
“Projecting the total interface participation to zero yields δ = (1.67±1.69) × 10 0 −7 , comparable with previously reported values for similar Si substrates 43,44 , although here it also includes JJ-induced losses.”
ResultInfluentialDetermining Interface Dielectric Losses in Superconducting Coplanar-Waveguide Resonators
Woods, W. H., Calusine, G., Melville, A. J., Sevi, A., Golden, E. B., Kim, D., Rosenberg, D., Yoder, J., & Oliver, W. (2019) · DSpace@MIT (Massachusetts Institute of Technology) · Cited by 146
Müller, C., Lisenfeld, J., Shnirman, A., & Poletto, S. (2015) · Physical Review B · doi:10.1103/physrevb.92.035442 · Cited by 144 · cited 2×
“Such temporal fluctuations are associated with coupling of the qubit to near-resonance two-level system (TLS) defects 37 , which are, in turn, longitudinally coupled to low-frequency (thermally active at 10 mK) two-level fluctuators (TLFs) 35,38,39 .”
BackgroundDynamics of superconducting qubit relaxation times
Carroll, M., Rosenblatt, S., Jurcevic, P., Lauer, I., & Kandala, A. (2022) · npj Quantum Information · doi:10.1038/s41534-022-00643-y · Cited by 136 · cited 1×
“However, individual, weakly coupled, TLS defects were spectrally resolved with swap spectroscopy 39,49 .”
BackgroundSolid-state qubits integrated with superconducting through-silicon vias
Yost, D. R. W., Schwartz, M. E., Mallek, J., Rosenberg, D., Stull, C., Yoder, J. L., Calusine, G., Cook, M., Das, R., Day, A. L., et al. (2020) · npj Quantum Information · doi:10.1038/s41534-020-00289-8 · Cited by 128 · cited 1×
“Our initial result showcases a leap forward in the potential fabrication volume and yield of high-coherence superconducting qubits, which, together with three-dimensional integration developments 5,31 , could meet the stringent fabrication demands of a future million-qubit processor.”
BackgroundTwo-level systems in superconducting quantum devices due to trapped quasiparticles
de Graaf, S. E., Faoro, L., Ioffe, L. B., Mahashabde, S., Burnett, J. J., Lindström, T., Kubatkin, S. E., Danilov, A. V., & Tzalenchuk, A. Y. (2020) · Science Advances · doi:10.1126/sciadv.abc5055 · Cited by 108 · cited 1×
“…that the most plausible explanation is the vanishing of a coupled TLF (and not a near-resonant TLS), possibly due to a defect rearrangement from an impinging high-energy radiation event 40 or due to a trapped quasiparticle escaping from a shallow, local well in the superconducting gap 41 .”
BackgroundSolid-state qubits integrated with superconducting through-silicon vias
Yost, D., Schwartz, M. E., Mallek, J., Rosenberg, D., Stull, C., Yoder, J., Calusine, G., Cook, M., Das, R. N., Day, A., et al. (2020) · DSpace@MIT (Massachusetts Institute of Technology) · Cited by 104
Overcoming leakage in quantum error correction
Miao, K. C., McEwen, M., Atalaya, J., Kafri, D., Pryadko, L. P., Bengtsson, A., Opremcak, A., Satzinger, K. J., Chen, Z., Klimov, P. V., et al. (2023) · Nature Physics · doi:10.1038/s41567-023-02226-w · Cited by 99 · cited 1×
“State-of-the-art demonstrations include error correction 10–14 , processors with hundreds of interconnected qubits and initial claims of quantum supremacy and utility 1,2 .”
BackgroundSelf-citationAcharya, R., Brebels, S., Grill, A., Verjauw, J., Ivanov, T., Lozano, D. P., Wan, D., Damme, J. V., Vadiraj, A. M., Mongillo, M., et al. (2023) · Nature Electronics · doi:10.1038/s41928-023-01033-8 · Cited by 96 · cited 1×
“Additionally, increased stability and uniformity of the qubits would reduce the significant control and tuning overhead 7 .”
BackgroundSelf-citationEnhanced coherence of all-nitride superconducting qubits epitaxially grown on silicon substrate
Kim, S., Terai, H., Yamashita, T., Qiu, W., Fuse, T., Yoshihara, F., Ashhab, S., Inomata, K., & Semba, K. (2021) · Communications Materials · doi:10.1038/s43246-021-00204-4 · Cited by 92
Fabrication of stable and reproducible submicron tunnel junctions
Pop, I. M., Fournier, T., Crozes, T., Lecocq, F., Matei, I., Pannetier, B., Buisson, O., & Guichard, W. (2012) · Journal of Vacuum Science & Technology B Nanotechnology and Microelectronics Materials Processing Measurement and Phenomena · doi:10.1116/1.3673790 · Cited by 89 · cited 1×
“Ageing can be linked to barrier impurities 57 or oxygen diffusion 3,58 .”
BackgroundBuilding blocks of a flip-chip integrated superconducting quantum processor
Kosen, S., Li, H.-X., Rommel, M., Shiri, D., Warren, C., Grönberg, L., Salonen, J., Abad, T., Biznárová, J., Caputo, M., et al. (2022) · Quantum Science and Technology · doi:10.1088/2058-9565/ac734b · Cited by 88 · cited 2×
“Moreover, it offers the potential for further upscaling through three-dimensional integration 5 and more process optimization.”
BackgroundSelf-citationOsman, A., Simon, J., Bengtsson, A., Kosen, S., Krantz, P., P. Lozano, D., Scigliuzzo, M., Delsing, P., Bylander, J., & Fadavi Roudsari, A. (2021) · Applied Physics Letters · doi:10.1063/5.0037093 · Cited by 87 · cited 2×
“Furthermore, the dependence of the R n RSD on the JJ area fits well with a model of constant area variance ( σ A2 ), derived by propagating the uncertainty 3,52 (Methods): Fitting the data to equation (2) allowed us to disentangle the barrier non-uniformity and area variability.”
MethodDemonstration of quantum volume 64 on a superconducting quantum computing system
Jurcevic, P., Javadi-Abhari, A., Bishop, L. S., Lauer, I., Bogorin, D. F., Brink, M., Capelluto, L., Günlük, O., Itoko, T., Kanazawa, N., et al. (2021) · Quantum Science and Technology · doi:10.1088/2058-9565/abe519 · Cited by 85 · cited 1×
“Moreover, it offers the potential for further upscaling through three-dimensional integration 5 and more process optimization.”
BackgroundTwo-level systems in superconducting quantum devices due to trapped quasiparticlesPreprint
de Graaf, S., Faoro, L., Ioffe, L. B., Mahashabde, S., Burnett, J., Lindström, T., Kubatkin, S., Danilov, A. V., & Tzalenchuk, A. Y. (2020) · HAL · Cited by 83
Constant-Overhead Quantum Error Correction with Thin Planar Connectivity
Tremblay, M. A., Delfosse, N., & Beverland, M. E. (2022) · Physical Review Letters · doi:10.1103/physrevlett.129.050504 · Cited by 83 · cited 1×
“As the complexity of quantum processors continues to grow, the need for stringent fabrication tolerances becomes increasingly critical 3 .”
BackgroundTwo-Level-System Dynamics in a Superconducting Qubit Due to Background Ionizing Radiation
Thorbeck, T., Eddins, A., Lauer, I., McClure, D. T., & Carroll, M. (2023) · PRX Quantum · doi:10.1103/prxquantum.4.020356 · Cited by 70 · cited 1×
“…that the most plausible explanation is the vanishing of a coupled TLF (and not a near-resonant TLS), possibly due to a defect rearrangement from an impinging high-energy radiation event 40 or due to a trapped quasiparticle escaping from a shallow, local well in the superconducting gap 41 .”
BackgroundComparison of dielectric loss in titanium nitride and aluminum superconducting resonators
Melville, A., Calusine, G., Woods, W., Serniak, K., Golden, E., Niedzielski, B. M., Kim, D. K., Sevi, A., Yoder, J. L., Dauler, E. A., et al. (2020) · Applied Physics Letters · doi:10.1063/5.0021950 · Cited by 69 · cited 1×
“Projecting the total interface participation to zero yields δ = (1.67±1.69) × 10 0 −7 , comparable with previously reported values for similar Si substrates 43,44 , although here it also includes JJ-induced losses.”
ResultInfluentialZeng, L., Tran, D. T., Tai, C.-W., Svensson, G., & Olsson, E. (2016) · Scientific Reports · doi:10.1038/srep29679 · Cited by 67
Comparison of dielectric loss in titanium nitride and aluminum superconducting resonators
Melville, A. J., Calusine, G., Woods, W. H., Serniak, K., Golden, E. B., Niedzielski, B. M., Kim, D., Sevi, A., Yoder, J., Dauler, E., et al. (2020) · DSpace@MIT (Massachusetts Institute of Technology) · Cited by 61
Merged-Element Transmons: Design and Qubit Performance
Mamin, H. J., Huang, E., Carnevale, S., Rettner, C. T., Arellano, N., Sherwood, M. H., Kurter, C., Trimm, B., Sandberg, M., Shelby, R. M., et al. (2021) · Physical Review Applied · doi:10.1103/physrevapplied.16.024023 · Cited by 57 · cited 2×
“The substrate–air, metal–air and substrate–metal interface participation ratios were calculated for the four different capacitor geometries (width and gap in {13, 24, 48, 90} μm).”
BackgroundMethodOverlap junctions for high coherence superconducting qubits
Wu, X., Long, J. L., Ku, H. S., Lake, R. E., Bal, M., & Pappas, D. P. (2017) · Applied Physics Letters · doi:10.1063/1.4993937 · Cited by 51 · cited 1×
“The JJ, a crucial element of a superconducting qubit, was fabricated using a 300 mm technology compatible overlap process 30,32,33 .”
MethodKono, S., Pan, J., Chegnizadeh, M., Wang, X., Youssefi, A., Scigliuzzo, M., & Kippenberg, T. J. (2024) · Nature Communications · doi:10.1038/s41467-024-48230-3 · Cited by 50
Moskalev, D. O., Zikiy, E. V., Pishchimova, A. A., Moskaleva, D. A., Smirnov, N. S., Ivanov, А. I., Korshakov, N. D., & Rodionov, I. A. (2023) · Scientific Reports · doi:10.1038/s41598-023-31003-1 · Cited by 49 · cited 1×
“The residual area variance could be addressed with more advanced lithographic control tricks and etch optimization beyond the range achievable at present with angled shadow-evaporation techniques, in principle 3,54 .”
BackgroundKoppinen, P. J., Väistö, L. M., & Maasilta, I. J. (2007) · Applied Physics Letters · doi:10.1063/1.2437662 · Cited by 47 · cited 1×
“Shadow-evaporated JJs often show notable parameter ageing (an increase in the normal resistance as a function of time), with reported values as high as tens of percents, over periods spanning days to weeks 3,55,56 .”
BackgroundPath toward manufacturable superconducting qubits with relaxation times exceeding 0.1 ms
Verjauw, J., Acharya, R., Van Damme, J., Ivanov, T., Lozano, D. P., Mohiyaddin, F. A., Wan, D., Jussot, J., Vadiraj, A. M., Mongillo, M., et al. (2022) · npj Quantum Information · doi:10.1038/s41534-022-00600-9 · Cited by 45 · cited 7×
“An example Al/AlO x /Al overlap JJ is visualized with a scanning electron microscopy (SEM) image in Fig.”
BackgroundMethodInfluentialSelf-citationEffects of laser-annealing on fixed-frequency superconducting qubits
Kim, H. L., Jünger, C., Morvan, A., Barnard, E. S., Livingston, W. P., Altoé, M. V. P., Kim, Y., Song, C., Chen, L., Kreikebaum, J. M., et al. (2022) · Applied Physics Letters · doi:10.1063/5.0102092 · Cited by 42 · cited 1×
“Shadow-evaporated JJs often show notable parameter ageing (an increase in the normal resistance as a function of time), with reported values as high as tens of percents, over periods spanning days to weeks 3,55,56 .”
BackgroundImproved coherence in optically defined niobium trilayer-junction qubits
Anferov, A., Lee, K.-H., Zhao, F., Simon, J., & Schuster, D. I. (2024) · Physical Review Applied · doi:10.1103/physrevapplied.21.024047 · Cited by 41 · cited 1×
“Although CMOS foundry-compatible processes 26–28 and qubits fabricated partially in a foundry environment 29 have been shown previously, the fabrication of 300 nm wafer-scale superconducting qubits has not been demonstrated.”
BackgroundMitigation of frequency collisions in superconducting quantum processors
Osman, A., Fernández-Pendás, J., Warren, C., Kosen, S., Scigliuzzo, M., Frisk Kockum, A., Tancredi, G., Fadavi Roudsari, A., & Bylander, J. (2023) · Physical Review Research · doi:10.1103/physrevresearch.5.043001 · Cited by 41 · cited 10×
“1), which is comparable to values reported for shadow-evaporated qubits 3 .”
BackgroundMethodResultInfluentialPishchimova, A. A., Smirnov, N. S., Ezenkova, D. A., Krivko, E. A., Zikiy, E. V., Moskalev, D. O., Ivanov, A. I., Korshakov, N. D., & Rodionov, I. A. (2023) · Scientific Reports · doi:10.1038/s41598-023-34051-9 · Cited by 39 · cited 1×
“The standard deviations for area are comparable with values reported in literature 3,53 .”
ResultCoherent superconducting qubits from a subtractive junction fabrication process
Stehli, A., Brehm, J. D., Wolz, T., Baity, P., Danilin, S., Seferai, V., Rotzinger, H., Ustinov, A. V., & Weides, M. (2020) · Applied Physics Letters · doi:10.1063/5.0023533 · Cited by 37 · cited 1×
“The JJ, a crucial element of a superconducting qubit, was fabricated using a 300 mm technology compatible overlap process 30,32,33 .”
MethodShiota, T., Imamura, T., & Hasuo, S. (1992) · IEEE Transactions on Applied Superconductivity · doi:10.1109/77.182734 · Cited by 36 · cited 1×
“The residual area variance could be addressed with more advanced lithographic control tricks and etch optimization beyond the range achievable at present with angled shadow-evaporation techniques, in principle 3,54 .”
BackgroundSimulating the fabrication of aluminium oxide tunnel junctions
Cyster, M. J., Smith, J. S., Vogt, N., Opletal, G., Russo, S. P., & Cole, J. H. (2021) · npj Quantum Information · doi:10.1038/s41534-020-00360-4 · Cited by 34 · cited 1×
“These demonstrations have all been done with architectures utilizing transmon-style qubits 15 with Al/AlO x /Al Josephson junctions (JJs) 16–18 , which are consistently fabricated using angled shadow evaporation and metal lift-off.”
MethodProbing defect densities at the edges and inside Josephson junctions of superconducting qubits
Bilmes, A., Volosheniuk, S., Ustinov, A. V., & Lisenfeld, J. (2022) · npj Quantum Information · doi:10.1038/s41534-022-00532-4 · Cited by 29 · cited 1×
“This is consistent with the previously observed resilience of Al to TLS defects induced by argon milling 34,46 .”
Analytical Determination of Participation in Superconducting Coplanar Architectures
Murray, C. E., Gambetta, J. M., McClure, D. T., & Steffen, M. (2018) · IEEE Transactions on Microwave Theory and Techniques · doi:10.1109/tmtt.2018.2841829 · Cited by 25 · cited 2×
“This allowed us to differentiate between loss sources at capacitor interfaces from other losses, such as bulk substrate loss and more importantly losses induced by the JJ.”
BackgroundSimulating the fabrication of aluminium oxide tunnel junctions
(20072829), M. C., (18031648), J. S., (235767), N. V., Opletal, G., Russo, S. P., & Cole, J. H. (2024) · Figshare · Cited by 25
Wan, D., Couet, S., Piao, X., Souriau, L., Canvel, Y., Tsvetanova, D., Vangoidsenhoven, D., Thiam, A., Pacco, A., Potočnik, A., et al. (2021) · Japanese Journal of Applied Physics · doi:10.35848/1347-4065/abe5bb · Cited by 20 · cited 2×
“We know from trilayer junctions (Nb/Al/AlO x /Nb) with similarly grown AlO x barriers at our facility that RSD R n 0.8% for large area junctions are attainable 26 (an upper bound for the RA variability).”
BackgroundInfluentialSelf-citationWu, Y.-L., Deng, H., Yu, H.-F., Xue, G.-M., Tian, Y., Li, J., Chen, Y.-F., Zhao, S.-P., & Zheng, D.-N. (2013) · Chinese Physics B · doi:10.1088/1674-1056/22/6/060309 · Cited by 18 · cited 1×
“The presented industry-scale fabrication process, which uses only optical lithography and reactive-ion etching, has a performance and yield in line with conventional laboratory-style techniques utilizing metal lift-off, angled evaporation and electron-beam writing 4 .”
MethodArgon-Milling-Induced Decoherence Mechanisms in Superconducting Quantum Circuits
Van Damme, J., Ivanov, T., Favia, P., Conard, T., Verjauw, J., Acharya, R., Perez Lozano, D., Raes, B., Van de Vondel, J., Vadiraj, A. M., et al. (2023) · Physical Review Applied · doi:10.1103/physrevapplied.20.014034 · Cited by 14 · cited 2×
“Furthermore, our results imply that the fabrication of the overlap JJ, including the physical damage to the junc-tion’s bottom electrode due to argon milling, did not cause a noticeable rise in TLS defect losses within the Al/AlO x /Al junction.”
MethodResultSelf-citationDevelopment of transmon qubits solely from optical lithography on 300 mm wafers
Foroozani, N., Hobbs, C., Hung, C. C., Olson, S., Ashworth, D., Holland, E., Malloy, M., Kearney, P., O’Brien, B., Bunday, B., et al. (2019) · Quantum Science and Technology · doi:10.1088/2058-9565/ab0ca8 · Cited by 13 · cited 1×
“Although CMOS foundry-compatible processes 26–28 and qubits fabricated partially in a foundry environment 29 have been shown previously, the fabrication of 300 nm wafer-scale superconducting qubits has not been demonstrated.”
BackgroundHigh-threshold and low-overhead fault-tolerant quantum memoryPreprint
Bravyi, S., Cross, A. W., Gambetta, J., et al. (2023) · arXiv (Cornell University) · doi:10.48550/arxiv.2308.07915 · Cited by 13 · cited 1×
“Advances in error-correcting codes 6 and quantum gate fidelities could reduce the required number of physical qubits.”
BackgroundPishchimova, A. A., Smirnov, N. S., Ezenkova, D. A., et al. (2022) · arXiv (Cornell University) · doi:10.48550/arxiv.2210.15293 · Cited by 2 · cited 1×
“The standard deviations for area are comparable with values reported in literature 3,53 .”
ResultAdvanced CMOS manufacturing of superconducting qubits on 300 mm wafers
Damme, J. V. (2024) · Zenodo · doi:10.5281/zenodo.13143313
Cited by
Tuokkola, M., Sunada, Y., Kivijärvi, H., Albanese, J., Grönberg, L., Kaikkonen, J.-P., Vesterinen, V., Govenius, J., & Möttönen, M. (2025) · Nature Communications · doi:10.1038/s41467-025-61126-0 · Cited by 132
Millisecond lifetimes and coherence times in 2D transmon qubits
Bland, M. P., Bahrami, F., Martinez, J. G. C., Prestegaard, P. H., Smitham, B. M., Joshi, A., Hedrick, E., Kumar, S., Yang, A., Pakpour‐Tabrizi, A. C., et al. (2025) · Nature · doi:10.1038/s41586-025-09687-4 · Cited by 205
Quantum Batteries: A Materials Science Perspective
Camposeo, A., Virgili, T., Lombardi, F., Cerullo, G., Pisignano, D., & Polini, M. (2025) · Advanced Materials · doi:10.1002/adma.202415073 · Cited by 50
Advancements in superconducting quantum computing
Jiang, Y.-Y., Deng, C., Fan, H., Li, B.-Y., Sun, L., Tan, X., Wang, W., Xue, G., Yan, F., Yu, H., et al. (2025) · National Science Review · doi:10.1093/nsr/nwaf246 · Cited by 83
“Future advancements, including industry-standard fabrication and leveraging semiconductor manufacturing facilities [47 ], aim to enhance yield, parameter control and coherence times, potentially exceeding the mi l lisecond level for very large-scale quantum processors.”
Zhang, G., Fan, X., Wang, Z., Li, P., Zhang, Z., Yu, B., Gao, D., Loke, D. K., Zhong, S., Wan, Q., et al. (2026) · Nano-Micro Letters · doi:10.1007/s40820-025-02035-1 · Cited by 19
Metadata
- Authors
- Van Damme, J., Massar, S., Acharya, R., Ivanov, T., Perez Lozano, D., Canvel, Y., Demarets, M., Vangoidsenhoven, D., Hermans, Y., Lai, J. G., Vadiraj, A. M., Mongillo, M., Wan, D., De Boeck, J., Potočnik, A., & De Greve, K.
- Affiliations
- IMEC (BE)
- Corresponding author
- Potočnik, A.
- Venue
- Nature
- Published
- 2024-09-18
- Volume
- 634
- Issue
- 8032
- Pages
- 74-79
- ISSN
- 0028-0836 (ISSN-L)
- 1476-4687
- PMC
- PMC11446867
- OpenAlex
- W4402585749
- Cited by
- 63
- References
- 86
- Citations by year
- 2026: 29 · 2025: 32 · 2024: 2
- FWCI
- 6.89
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Licence
- cc-by
- creativecommons.org/licenses/by/4.0 (tdm)
- creativecommons.org/licenses/by/4.0 (vor)
- Locations
- Nature (publishedVersion, cc-by)
- PubMed (publishedVersion)
- arXiv (Cornell University) (submittedVersion, cc-by-nc-nd)
- Lirias (submittedVersion, cc-by)
- PubMed Central (submittedVersion, cc-by)
- arXiv (Cornell University)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advancements in Semiconductor Devices and Circuit Design
- Physical Sciences › Computer Science › Artificial Intelligence › Quantum Computing Algorithms and Architecture
- Physical Sciences › Computer Science › Computational Theory and Mathematics › Quantum-Dot Cellular Automata
- Keywords
- superconducting qubits, transmon qubits, CMOS-compatible fabrication, 300 mm wafers, coherence time, relaxation time, fabrication yield, device variability
- MeSH terms
- Superconductivity, Metals, Oxides, Quantum Theory, Semiconductors
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.