The DOI matches its Crossref record; 134 of the 134 references it cites were found in a registry or an index.
From lab to fab: how must the polymer solar cell materials design change? – an industrial perspective
Abstract
Organic photovoltaic (OPV) devices, in particular polymer solar cells, made by solution processed organic materials have shown great promise as a disruptive technology for affordable electricity. Even though recent advances look impressive on paper, until now the commercialization of OPV has been hampered by the difficulty of converting lab produced “champion” cell figures into reliable industrial-scale product performances. A key factor to achieve this condition is to develop OPV materials (polymer donors, acceptors, buffer materials, electrodes materials and encapsulants) exhibiting the required technical and economic characteristics to be conveniently used in an industrial environment. The well established strategies for the design of materials for efficient lab-scale OPV devices are not sufficient when large-area printed panels are concerned. A number of additional requirements, normally not addressed in the laboratory context, must be met: the materials must be easily accessible as pure compounds in few synthetic steps from cheap starting compounds, need to be stable and soluble enough to afford ink formulations processable with roll-to-roll compatible equipment; solvent and solvent additives should be easily removable after printing, and possibly should be environmentally friendly compounds; the layers should achieve a stable morphology under mild conditions (low temperatures and short times); the above mentioned materials can be screened on glass substrates, but should be finally tested on plastic films, protected through a scalable encapsulation technique. The more researchers adhere to these guidelines, the greater the possibility for OPV to demonstrate at last its enormous potential on the industrial scale.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Roll-to-roll production of 30-inch graphene films for transparent electrodes
Bae, S., Kim, H., Lee, Y., Xu, X., Park, J.-S., Zheng, Y., Balakrishnan, J., Lei, T., Ri Kim, H., Song, Y. I., et al. (2010) · Nature Nanotechnology · doi:10.1038/nnano.2010.132 · Cited by 8,136
Li, G., Shrotriya, V., Huang, J., Yao, Y., Moriarty, T., Emery, K., & Yang, Y. (2005) · Nature Materials · doi:10.1038/nmat1500 · Cited by 5,535
Design Rules for Donors in Bulk‐Heterojunction Solar Cells—Towards 10 % Energy‐Conversion Efficiency
Scharber, M. C., Mühlbacher, D., Koppe, M., Denk, P., Waldauf, C., Heeger, A. J., & Brabec, C. J. (2006) · Advanced Materials · doi:10.1002/adma.200501717 · Cited by 5,205
Bulk heterojunction solar cells with internal quantum efficiency approaching 100%
Park, S. H., Roy, A., Beaupré, S., Cho, S., Coates, N., Moon, J. S., Moses, D., Leclerc, M., Lee, K., & Heeger, A. J. (2009) · Nature Photonics · doi:10.1038/nphoton.2009.69 · Cited by 4,073
Synthesis of Conjugated Polymers for Organic Solar Cell Applications
Cheng, Y.-J., Yang, S.-H., & Hsu, C.-S. (2009) · Chemical Reviews · doi:10.1021/cr900182s · Cited by 3,972
Enhanced power-conversion efficiency in polymer solar cells using an inverted device structure
He, Z., Zhong, C., Su, S., Xu, M., Wu, H., & Cao, Y. (2012) · Nature Photonics · doi:10.1038/nphoton.2012.190 · Cited by 3,764
Fabrication and processing of polymer solar cells: A review of printing and coating techniques
Krebs, F. C. (2009) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2008.10.004 · Cited by 3,260
Efficiency enhancement in low-bandgap polymer solar cells by processing with alkane dithiols
Peet, J., Kim, J. Y., Coates, N. E., Ma, W. L., Moses, D., Heeger, A. J., & Bazan, G. C. (2007) · Nature Materials · doi:10.1038/nmat1928 · Cited by 3,202
Polymer‐Fullerene Bulk‐Heterojunction Solar Cells
Dennler, G., Scharber, M. C., & Brabec, C. J. (2009) · Advanced Materials · doi:10.1002/adma.200801283 · Cited by 3,114
Unimpeded Permeation of Water Through Helium-Leak–Tight Graphene-Based Membranes
Nair, R. R., Wu, H. A., Jayaram, P. N., Grigorieva, I. V., & Geim, A. K. (2012) · Science · doi:10.1126/science.1211694 · Cited by 3,073
Li, Y. (2012) · Accounts of Chemical Research · doi:10.1021/ar2002446 · Cited by 2,756
Polymer–Fullerene Bulk‐Heterojunction Solar Cells
Brabec, C. J., Gowrisanker, S., Halls, J. J. M., Laird, D., Jia, S., & Williams, S. P. (2010) · Advanced Materials · doi:10.1002/adma.200903697 · Cited by 2,621
π-Conjugated Polymers for Organic Electronics and Photovoltaic Cell Applications
Facchetti, A. (2011) · Chemistry of Materials · doi:10.1021/cm102419z · Cited by 2,348
Stability/degradation of polymer solar cells
Jørgensen, M., Norrman, K., & Krebs, F. C. (2008) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2008.01.005 · Cited by 2,335
He, Z., Zhong, C., Huang, X., Wong, W., Wu, H., Chen, L., Su, S., & Cao, Y. (2011) · Advanced Materials · doi:10.1002/adma.201103006 · Cited by 2,134
Processing Additives for Improved Efficiency from Bulk Heterojunction Solar Cells
Lee, J. K., Ma, W. L., Brabec, C. J., Yuen, J., Moon, J. S., Kim, J. Y., Lee, K., Bazan, G. C., & Heeger, A. J. (2008) · Journal of the American Chemical Society · doi:10.1021/ja710079w · Cited by 1,613
Sun, Y., Seo, J. H., Takacs, C. J., Seifter, J., & Heeger, A. J. (2011) · Advanced Materials · doi:10.1002/adma.201004301 · Cited by 1,545
Price, S. C., Stuart, A. C., Yang, L., Zhou, H., & You, W. (2011) · Journal of the American Chemical Society · doi:10.1021/ja1112595 · Cited by 1,505
Roll-to-roll fabrication of polymer solar cells
Søndergaard, R., Hösel, M., Angmo, D., Larsen-Olsen, T. T., & Krebs, F. C. (2012) · Materials Today · doi:10.1016/s1369-7021(12)70019-6 · Cited by 1,450
Morphology of polymer/fullerene bulk heterojunction solar cells
Hoppe, H., & Sariciftci, N. S. (2006) · J. Mater. Chem. · doi:10.1039/b510618b · Cited by 1,414
Liang, Y., Feng, D., Wu, Y., Tsai, S.-T., Li, G., Ray, C., & Yu, L. (2009) · Journal of the American Chemical Society · doi:10.1021/ja901545q · Cited by 1,387
Toward a Rational Design of Poly(2,7-Carbazole) Derivatives for Solar Cells
Blouin, N., Michaud, A., Gendron, D., Wakim, S., Blair, E., Neagu-Plesu, R., Belletête, M., Durocher, G., Tao, Y., & Leclerc, M. (2008) · Journal of the American Chemical Society · doi:10.1021/ja0771989 · Cited by 1,370
Stability of Polymer Solar Cells
Jørgensen, M., Norrman, K., Gevorgyan, S. A., Tromholt, T., Andreasen, B., & Krebs, F. C. (2012) · Advanced Materials · doi:10.1002/adma.201104187 · Cited by 1,366
P3HT:PCBM, Best Seller in Polymer Photovoltaic Research
Dang, M. T., Hirsch, L., & Wantz, G. (2011) · Advanced Materials · doi:10.1002/adma.201100792 · Cited by 1,261
Krebs, F. C., Gevorgyan, S. A., & Alstrup, J. (2009) · Journal of Materials Chemistry · doi:10.1039/b823001c · Cited by 1,229
Organic photovoltaics: technology and market
Brabec, C. J. (2004) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2004.02.030 · Cited by 1,152
Li, G., Yao, Y., Yang, H., Shrotriya, V., Yang, G., & Yang, Y. (2007) · Advanced Functional Materials · doi:10.1002/adfm.200600624 · Cited by 1,147
Yip, H.-L., & Jen, A. K.-Y. (2012) · Energy & Environmental Science · doi:10.1039/c2ee02806a · Cited by 1,117
Side Chain Engineering in Solution-Processable Conjugated Polymers
Mei, J., & Bao, Z. (2014) · Chemistry of Materials · doi:10.1021/cm4020805 · Cited by 1,054
Transition metal oxides as the buffer layer for polymer photovoltaic cells
Shrotriya, V., Li, G., Yao, Y., Chu, C.-W., & Yang, Y. (2006) · Applied Physics Letters · doi:10.1063/1.2174093 · Cited by 1,035
Upscaling of polymer solar cell fabrication using full roll-to-roll processing
Krebs, F. C., Tromholt, T., & Jørgensen, M. (2010) · Nanoscale · doi:10.1039/b9nr00430k · Cited by 1,024
Interface Engineering for Organic Electronics
Ma, H., Yip, H., Huang, F., & Jen, A. K. ‐. (2010) · Advanced Functional Materials · doi:10.1002/adfm.200902236 · Cited by 950
Fullerene derivative acceptors for high performance polymer solar cells
He, Y., & Li, Y. (2011) · Phys. Chem. Chem. Phys. · doi:10.1039/c0cp01178a · Cited by 941
Transparent Conducting Oxides for Photovoltaics
Fortunato, E., Ginley, D., Hosono, H., & Paine, D. C. (2007) · MRS Bulletin · doi:10.1557/mrs2007.29 · Cited by 918
The Race To Replace Tin-Doped Indium Oxide: Which Material Will Win?
Kumar, A., & Zhou, C. (2010) · ACS Nano · doi:10.1021/nn901903b · Cited by 843
Processable Low-Bandgap Polymers for Photovoltaic Applications
Boudreault, P.-L. T., Najari, A., & Leclerc, M. (2011) · Chemistry of Materials · doi:10.1021/cm1021855 · Cited by 827
Krebs, F. C., Jørgensen, M., Norrman, K., Hagemann, O., Alstrup, J., Nielsen, T. D., Fyenbo, J., Larsen, K., & Kristensen, J. (2009) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2008.12.001 · Cited by 808
Krebs, F. C. (2009) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2008.12.012 · Cited by 780
Stille Polycondensation for Synthesis of Functional Materials
Carsten, B., He, F., Son, H. J., Xu, T., & Yu, L. (2011) · Chemical Reviews · doi:10.1021/cr100320w · Cited by 755
Degradation of organic solar cells due to air exposure
Kawano, K., Pacios, R., Poplavskyy, D., Nelson, J., Bradley, D. D. C., & Durrant, J. R. (2006) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2006.06.041 · Cited by 734
Molecular Engineering of the Band Gap of π‐Conjugated Systems: Facing Technological Applications
Roncali, J. (2007) · Macromolecular Rapid Communications · doi:10.1002/marc.200700345 · Cited by 722
Polymer donor–polymer acceptor (all-polymer) solar cells
Facchetti, A. (2013) · Materials Today · doi:10.1016/j.mattod.2013.04.005 · Cited by 688
Material challenge for flexible organic devices
Lewis, J. (2006) · Materials Today · doi:10.1016/s1369-7021(06)71446-8 · Cited by 662
Zardetto, V., Brown, T. M., Reale, A., & Di Carlo, A. (2011) · Journal of Polymer Science Part B: Polymer Physics · doi:10.1002/polb.22227 · Cited by 622
Wang, M., Hu, X., Liu, P., Li, W., Gong, X., Huang, F., & Cao, Y. (2011) · Journal of the American Chemical Society · doi:10.1021/ja201131h · Cited by 620
Strain-dependent electrical resistance of tin-doped indium oxide on polymer substrates
Cairns, D. R., Witte, R. P., Sparacin, D. K., Sachsman, S. M., Paine, D. C., Crawford, G. P., & Newton, R. R. (2000) · Applied Physics Letters · doi:10.1063/1.126052 · Cited by 616
Additives for morphology control in high-efficiency organic solar cells
Liao, H.-C., Ho, C.-C., Chang, C.-Y., Jao, M.-H., Darling, S. B., & Su, W.-F. (2013) · Materials Today · doi:10.1016/j.mattod.2013.08.013 · Cited by 535
Durability of nanosized oxygen-barrier coatings on polymers
Leterrier, Y. (2003) · Progress in Materials Science · doi:10.1016/s0079-6425(02)00002-6 · Cited by 509
The case for organic photovoltaics
Darling, S. B., & You, F. (2013) · RSC Advances · doi:10.1039/c3ra42989j · Cited by 508
Solar cells with one-day energy payback for the factories of the future
Espinosa, N., Hösel, M., Angmo, D., & Krebs, F. C. (2012) · Energy Environ. Sci. · doi:10.1039/c1ee02728j · Cited by 496
Computational methods for design of organic materials with high charge mobility
Wang, L., Nan, G., Yang, X., Peng, Q., Li, Q., & Shuai, Z. (2010) · Chem. Soc. Rev. · doi:10.1039/b816406c · Cited by 482
The role of buffer layers in polymer solar cells
Po, R., Carbonera, C., Bernardi, A., & Camaioni, N. (2011) · Energy Environ. Sci. · doi:10.1039/c0ee00273a · Cited by 480
Self-citationHuo, L., Hou, J., Chen, H.-Y., Zhang, S., Jiang, Y., Chen, T. L., & Yang, Y. (2009) · Macromolecules · doi:10.1021/ma9012972 · Cited by 467
Incorporation of Furan into Low Band-Gap Polymers for Efficient Solar Cells
Woo, C. H., Beaujuge, P. M., Holcombe, T. W., Lee, O. P., & Fréchet, J. M. J. (2010) · Journal of the American Chemical Society · doi:10.1021/ja108115y · Cited by 458
Fonoberov, V. A., Alim, K. A., Balandin, A. A., Xiu, F., & Liu, J. (2006) · Physical Review B · doi:10.1103/physrevb.73.165317 · Cited by 437
Chen, W., Xu, T., He, F., Wang, W., Wang, C., Strzalka, J., Liu, Y., Wen, J., Miller, D. J., Chen, J., et al. (2011) · Nano Letters · doi:10.1021/nl201715q · Cited by 424
Small-Molecule, Nonfullerene Acceptors for Polymer Bulk Heterojunction Organic Photovoltaics
Anthony, J. E. (2011) · Chemistry of Materials · doi:10.1021/cm1023019 · Cited by 412
Estimating the manufacturing cost of purely organic solar cells
Kalowekamo, J., & Baker, E. (2009) · Solar Energy · doi:10.1016/j.solener.2009.02.003 · Cited by 384
Organic non-fullerene acceptors for organic photovoltaics
Sonar, P., Fong Lim, J. P., & Chan, K. L. (2011) · Energy & Environmental Science · doi:10.1039/c0ee00668h · Cited by 378
Flexible organic P3HT:PCBM bulk-heterojunction modules with more than 1 year outdoor lifetime
Hauch, J. A., Schilinsky, P., Choulis, S. A., Childers, R., Biele, M., & Brabec, C. J. (2008) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2008.01.004 · Cited by 373
Latest advances in substrates for flexible electronics
MacDonald, W. A., Looney, M. K., MacKerron, D., Eveson, R., Adam, R., Hashimoto, K., & Rakos, K. (2007) · Journal of the Society for Information Display · doi:10.1889/1.2825093 · Cited by 360
Espinosa, N., García-Valverde, R., Urbina, A., & Krebs, F. C. (2011) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2010.08.020 · Cited by 342
Chochos, C. L., & Choulis, S. A. (2011) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2011.04.003 · Cited by 340
Effect of synthetic accessibility on the commercial viability of organic photovoltaics
Osedach, T. P., Andrew, T. L., & Bulović, V. (2013) · Energy & Environmental Science · doi:10.1039/c3ee24138f · Cited by 333
Collins, B. A., Tumbleston, J. R., & Ade, H. (2011) · The Journal of Physical Chemistry Letters · doi:10.1021/jz2014902 · Cited by 321
Predicting Morphologies of Solution Processed Polymer:Fullerene Blends
Kouijzer, S., Michels, J. J., van den Berg, M., Gevaerts, V. S., Turbiez, M., Wienk, M. M., & Janssen, R. A. J. (2013) · Journal of the American Chemical Society · doi:10.1021/ja405493j · Cited by 316
Dou, L., Chen, C.-C., Yoshimura, K., Ohya, K., Chang, W.-H., Gao, J., Liu, Y., Richard, E., & Yang, Y. (2013) · Macromolecules · doi:10.1021/ma400452j · Cited by 310
Direct Monolithic Integration of Organic Photovoltaic Circuits on Unmodified Paper
Barr, M. C., Rowehl, J. A., Lunt, R. R., Xu, J., Wang, A., Boyce, C. M., Im, S. G., Bulović, V., & Gleason, K. K. (2011) · Advanced Materials · doi:10.1002/adma.201101263 · Cited by 291
Huo, L., & Hou, J. (2011) · Polymer Chemistry · doi:10.1039/c1py00197c · Cited by 289
Green chemistry for organic solar cells
Burke, D. J., & Lipomi, D. J. (2013) · Energy & Environmental Science · doi:10.1039/c3ee41096j · Cited by 283
Bian, L., Zhu, E., Tang, J., Tang, W., & Zhang, F. (2012) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2012.03.001 · Cited by 269
Risko, C., McGehee, M. D., & Brédas, J.-L. (2011) · Chem. Sci. · doi:10.1039/c0sc00642d · Cited by 257
Photochemical stability of π-conjugated polymers for polymer solar cells: a rule of thumb
Manceau, M., Bundgaard, E., Carlé, J. E., Hagemann, O., Helgesen, M., Søndergaard, R., Jørgensen, M., & Krebs, F. C. (2011) · Journal of Materials Chemistry · doi:10.1039/c0jm03105d · Cited by 253
Entropy of Charge Separation in Organic Photovoltaic Cells: The Benefit of Higher Dimensionality
Gregg, B. A. (2011) · The Journal of Physical Chemistry Letters · doi:10.1021/jz2012403 · Cited by 245
Organic photovoltaics for low light applications
Steim, R., Ameri, T., Schilinsky, P., Waldauf, C., Dennler, G., Scharber, M. C., & Brabec, C. J. (2011) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2011.07.011 · Cited by 243
Permeation rate measurements by electrical analysis of calcium corrosion
Paetzold, R., Winnacker, A., Henseler, D., Cesari, V., & Heuser, K. (2003) · Review of Scientific Instruments · doi:10.1063/1.1626015 · Cited by 239
Inverted Polymer Solar Cells with Reduced Interface Recombination
Chen, S., Small, C. E., Amb, C. M., Subbiah, J., Lai, T., Tsang, S., Manders, J. R., Reynolds, J. R., & So, F. (2012) · Advanced Energy Materials · doi:10.1002/aenm.201200184 · Cited by 235
Søndergaard, R., Helgesen, M., Jørgensen, M., & Krebs, F. C. (2011) · Advanced Energy Materials · doi:10.1002/aenm.201000007 · Cited by 234
Ye, L., Jing, Y., Guo, X., Sun, H., Zhang, S., Zhang, M., Huo, L., & Hou, J. (2013) · The Journal of Physical Chemistry C · doi:10.1021/jp404395q · Cited by 232
A microscopic model for the behavior of nanostructured organic photovoltaic devices
Marsh, R. A., Groves, C., & Greenham, N. C. (2007) · Journal of Applied Physics · doi:10.1063/1.2718865 · Cited by 231
Cowan, S. R., Leong, W. L., Banerji, N., Dennler, G., & Heeger, A. J. (2011) · Advanced Functional Materials · doi:10.1002/adfm.201100514 · Cited by 229
Materials and methods for encapsulation of OPV: A review
Ahmad, J., Bazaka, K., Anderson, L. J., White, R. D., & Jacob, M. V. (2013) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2013.06.027 · Cited by 222
Dou, L., Chen, C.-C., Yoshimura, K., Ohya, K., Chang, W.-H., Gao, J., Liu, Y., Richard, E., & Yang, Y. (2013) · Macromolecules · doi:10.1021/ma400974a · Cited by 222
Printed Paper Photovoltaic Cells
Hübler, A., Trnovec, B., Zillger, T., Ali, M., Wetzold, N., Mingebach, M., Wagenpfahl, A., Deibel, C., & Dyakonov, V. (2011) · Advanced Energy Materials · doi:10.1002/aenm.201100394 · Cited by 215
Interlayer adhesion in roll-to-roll processed flexible inverted polymer solar cells
Dupont, S. R., Oliver, M. S., Krebs, F. C., & Dauskardt, R. H. (2011) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2011.10.012 · Cited by 209
Longterm stability of efficient inverted P3HT:PCBM solar cells
Zimmermann, B., Würfel, U., & Niggemann, M. (2009) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2008.12.022 · Cited by 208
Life cycle analyses of organic photovoltaics: a review
Lizin, S., Van Passel, S., De Schepper, E., Maes, W., Lutsen, L., Manca, J., & Vanderzande, D. (2013) · Energy & Environmental Science · doi:10.1039/c3ee42653j · Cited by 206
Olivares-Amaya, R., Amador-Bedolla, C., Hachmann, J., Atahan-Evrenk, S., Sánchez-Carrera, R. S., Vogt, L., & Aspuru-Guzik, A. (2011) · Energy & Environmental Science · doi:10.1039/c1ee02056k · Cited by 204
Alstrup, J., Jørgensen, M., Medford, A. J., & Krebs, F. C. (2010) · ACS Applied Materials & Interfaces · doi:10.1021/am100505e · Cited by 201
Flexible ITO‐free polymer solar cells
Angmo, D., & Krebs, F. C. (2012) · Journal of Applied Polymer Science · doi:10.1002/app.38854 · Cited by 191
Life cycle analysis of organic photovoltaic technologies
García‐Valverde, R., Cherni, J. A., & Urbina, A. (2010) · Progress in Photovoltaics Research and Applications · doi:10.1002/pip.967 · Cited by 191
Efficient Computational Screening of Organic Polymer Photovoltaics
Kanal, I. Y., Owens, S. G., Bechtel, J. S., & Hutchison, G. R. (2013) · The Journal of Physical Chemistry Letters · doi:10.1021/jz400215j · Cited by 182
Light-induced degradation of the active layer of polymer-based solar cells
Rivaton, A., Chambon, S., Manceau, M., Gardette, J.-L., Lemaître, N., & Guillerez, S. (2010) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2009.11.021 · Cited by 181
Detection and role of trace impurities in high-performance organic solar cells
Nikiforov, M. P., Lai, B., Chen, W., Chen, S., Schaller, R. D., Strzalka, J., Maser, J., & Darling, S. B. (2013) · Energy & Environmental Science · doi:10.1039/c3ee40556g · Cited by 181
Computational Design and Selection of Optimal Organic Photovoltaic Materials
O’Boyle, N. M., Campbell, C. M., & Hutchison, G. R. (2011) · The Journal of Physical Chemistry C · doi:10.1021/jp202765c · Cited by 179
Chueh, C.-C., Yao, K., Yip, H.-L., Chang, C.-Y., Xu, Y.-X., Chen, K.-S., Li, C.-Z., Liu, P., Huang, F., Chen, Y., et al. (2013) · Energy & Environmental Science · doi:10.1039/c3ee41915k · Cited by 176
Technology development for roll-to-roll production of organic photovoltaics
Galagan, Y., de Vries, I. G., Langen, A. P., Andriessen, R., Verhees, W. J. H., Veenstra, S. C., & Kroon, J. M. (2011) · Chemical Engineering and Processing: Process Intensification · doi:10.1016/j.cep.2010.07.012 · Cited by 170
Osaka, I., Saito, M., Mori, H., Koganezawa, T., & Takimiya, K. (2012) · Advanced Materials · doi:10.1002/adma.201103065 · Cited by 169
On the role of intermixed phases in organic photovoltaic blends
Westacott, P., Tumbleston, J. R., Shoaee, S., Fearn, S., Bannock, J. H., Gilchrist, J. B., Heutz, S., deMello, J., Heeney, M., Ade, H., et al. (2013) · Energy & Environmental Science · doi:10.1039/c3ee41821a · Cited by 169
The state of organic solar cells—A meta analysis
Jørgensen, M., Carlé, J. E., Søndergaard, R. R., Lauritzen, M., Dagnæs-Hansen, N. A., Byskov, S. L., Andersen, T. R., Larsen-Olsen, T. T., Böttiger, A. P. L., Andreasen, B., et al. (2013) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2013.05.034 · Cited by 165
Gravure printed flexible organic photovoltaic modules
Kopola, P., Aernouts, T., Sliz, R., Guillerez, S., Ylikunnari, M., Cheyns, D., Välimäki, M. K., Tuomikoski, M., Hast, J. T., Jabbour, G. E., et al. (2011) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2010.12.020 · Cited by 160
Blankenburg, L., Schultheis, K., Schache, H., Sensfuss, S., & Schrödner, M. (2009) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2008.12.013 · Cited by 160
Ex‐ante environmental and economic evaluation of polymer photovoltaics
Roes, A. L., Alsema, E. A., Blok, K., & Patel, M. K. (2009) · Progress in Photovoltaics: Research and Applications · doi:10.1002/pip.891 · Cited by 159
Structure and oxygen-barrier properties of metallized polymer film
Jamieson, E. H. H., & Windle, A. H. (1983) · Journal of Materials Science · doi:10.1007/bf00543811 · Cited by 150
Solution processed metal-oxides for organic electronic devices
Zilberberg, K., Meyer, J., & Riedl, T. (2013) · Journal of Materials Chemistry C · doi:10.1039/c3tc30930d · Cited by 147
Pó, R., Carbonera, C., Bernardi, A., Tinti, F., & Camaioni, N. (2012) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2011.12.022 · Cited by 146
Self-citationGuo, J., Liang, Y., Szarko, J. M., Lee, B., Son, H. J., Rolczynski, B. S., Yu, L., & Chen, L. X. (2009) · The Journal of Physical Chemistry B · doi:10.1021/jp909135k · Cited by 144
Effect of P3HT:PCBM concentration in solvent on performances of organic solar cells
Baek, W., Yang, H. S., Yoon, T., Kang, C. J., Lee, H. H., & Kim, Y. (2009) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2009.01.019 · Cited by 144
Degradation and stability of polymer-based solar cells
Lee, J. U., Jung, J. W., Jo, J. W., & Jo, W. H. (2012) · Journal of Materials Chemistry · doi:10.1039/c2jm33645f · Cited by 143
Park, H. J., Kang, M., Ahn, S. H., & Guo, L. J. (2010) · Advanced Materials · doi:10.1002/adma.201000250 · Cited by 141
Pivrikas, A., Neugebauer, H., & Sariçiftçi, N. S. (2010) · Solar Energy · doi:10.1016/j.solener.2010.10.012 · Cited by 140
Helgesen, M., Gevorgyan, S. A., Krebs, F. C., & Janssen, R. A. J. (2009) · Chemistry of Materials · doi:10.1021/cm901937d · Cited by 139
Khlyabich, P. P., Burkhart, B., Rudenko, A. E., & Thompson, B. C. (2013) · Polymer · doi:10.1016/j.polymer.2013.07.053 · Cited by 132
Mechanical Stability of Externally Deformed Indium–Tin–Oxide Films on Polymer Substrates
Park, S. K., Han, J. I., Moon, D., & Kim, W. K. (2003) · Japanese Journal of Applied Physics · doi:10.1143/jjap.42.623 · Cited by 129
Reporting Performance in Organic Photovoltaic Devices
Luber, E. J., & Buriak, J. M. (2013) · ACS Nano · doi:10.1021/nn402883g · Cited by 122
Organic photovoltaic modules fabricated by an industrial gravure printing proofer
Yang, J., Vak, D., Clark, N. B., Subbiah, J., Wong, W. W. H., Jones, D. J., Watkins, S. E., & Wilson, G. (2012) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2012.10.018 · Cited by 118
Banerji, N., Eric Gagnon, A., Morgantini, P., Valouch, S., Mohebbi, A. R., Seo, J. H., Leclerc, M., & Heeger, A. J. (2012) · The Journal of Physical Chemistry C · doi:10.1021/jp301639e · Cited by 115
Chang, C., Zuo, L., Yip, H., Li, Y., Li, C., Hsu, C., Cheng, Y., Chen, H., & Jen, A. K. ‐. (2013) · Advanced Functional Materials · doi:10.1002/adfm201301557 · Cited by 115
Yue, D., Khatav, P., You, F., & Darling, S. B. (2012) · Energy & Environmental Science · doi:10.1039/c2ee22597b · Cited by 114
Zhang, Y. A., Zou, J., Yip, H., Chen, K., Davies, J. A., Sun, Y., & Jen, A. K. ‐. (2011) · Macromolecules · doi:10.1021/ma2008699 · Cited by 113
Efficient Solar Cells from Semi-random P3HT Analogues Incorporating Diketopyrrolopyrrole
Khlyabich, P. P., Burkhart, B., Ng, C. F., & Thompson, B. C. (2011) · Macromolecules · doi:10.1021/ma2009386 · Cited by 110
Mateker, W. R., Douglas, J. D., Cabanetos, C., Sachs‐Quintana, I. T., Bartelt, J. A., Hoke, E. T., Labban, A. E., Beaujuge, P. M., Fréchet, J. M. J., & McGehee, M. D. (2013) · Energy & Environmental Science · doi:10.1039/c3ee41328d · Cited by 108
Yang, T., Wang, M., Cao, Y. X., Huang, F., Huang, L., Peng, J., Gong, X., Cheng, S. Z. D., & Cao, Y. (2012) · Advanced Energy Materials · doi:10.1002/aenm.201100598 · Cited by 106
Saeki, A., Tsuji, M., & Seki, S. (2011) · Advanced Energy Materials · doi:10.1002/aenm.201100143 · Cited by 103
Hösel, M., Søndergaard, R. R., Jørgensen, M., & Krebs, F. C. (2013) · Advanced Engineering Materials · doi:10.1002/adem.201300172 · Cited by 101
Life-cycle analysis of product integrated polymer solar cells
Espinosa, N., García‐Valverde, R., & Krebs, F. C. (2011) · Energy & Environmental Science · doi:10.1039/c1ee01127h · Cited by 101
Synthesis and photovoltaic performance of a series of small band gap polymers
Zoombelt, A. P., Fonrodona, M., Turbiez, M. G. R., Wienk, M. M., & Janssen, R. A. J. (2009) · Journal of Materials Chemistry · doi:10.1039/b821979f · Cited by 96
Liu, Y., Larsen‐Olsen, T. T., Zhao, X., Andreasen, B., Søndergaard, R. R., Helgesen, M., Norrman, K., Jørgensen, M., Krebs, F. C., & Zhan, X. (2013) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2013.01.025 · Cited by 85
Designing Polymers for Photovoltaic Applications Using ab Initio Calculations
Bérubé, N., Gosselin, V., Gaudreau, J., & Côté, M. (2013) · The Journal of Physical Chemistry C · doi:10.1021/jp309800f · Cited by 73
An overview of molecular acceptors for organic solar cells
Hudhomme, P. (2013) · EPJ Photovoltaics · doi:10.1051/epjpv/2013020 · Cited by 66
Optimisation of PCPDTBT solar cells using polymer synthesis with Suzuki coupling
Kettle, J., Horie, M., Majewski, L. A., Saunders, B. R., Tuladhar, S. M., Nelson, J., & Turner, M. L. (2011) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2011.03.022 · Cited by 64
Inkjet printed solar cell active layers prepared from chlorine-free solvent systems
Lange, A., Schindler, W., Wegener, M., Fostiropoulos, K., & Janietz, S. (2012) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2012.10.011 · Cited by 54
Nie, W., MacNeill, C. M., Li, Y., Noftle, R. E., Carroll, D., & Coffin, R. C. (2011) · Macromolecular Rapid Communications · doi:10.1002/marc.201100161 · Cited by 51
Cited by
High-efficiency and air-stable P3HT-based polymer solar cells with a new non-fullerene acceptor
Holliday, S., Ashraf, R. S., Wadsworth, A., Baran, D., Yousaf, S. A., Nielsen, C. B., Tan, C.-H., Dimitrov, S. D., Shang, Z., Gasparini, N., et al. (2016) · Nature Communications · doi:10.1038/ncomms11585 · Cited by 1,195
Meng, D., Sun, D., Zhong, C., Liu, T., Fan, B., Huo, L., Li, Y., Jiang, W., Choi, H., Kim, T., et al. (2016) · Journal of the American Chemical Society · doi:10.1021/jacs.5b11149 · Cited by 706
Solvent Additives: Key Morphology‐Directing Agents for Solution‐Processed Organic Solar Cells
McDowell, C., Abdelsamie, M., Toney, M. F., & Bazan, G. C. (2018) · Advanced Materials · doi:10.1002/adma.201707114 · Cited by 513
The role of the third component in ternary organic solar cells
Gasparini, N., Salleo, A., McCulloch, I., & Baran, D. (2019) · Nature Reviews Materials · doi:10.1038/s41578-019-0093-4 · Cited by 494
Recent progress in non-fullerene small molecule acceptors in organic solar cells (OSCs)
Chen, W., & Zhang, Q. (2017) · Journal of Materials Chemistry C · doi:10.1039/c6tc05066b · Cited by 407
Metadata
- Authors
- Po, R., Bernardi, A., Calabrese, A., Carbonera, C., Corso, G., & Pellegrino, A.
- Venue
- Energy & Environmental Science
- Publisher
- Royal Society of Chemistry (RSC)
- Published
- 2014
- Volume
- 7
- Issue
- 3
- Pages
- 925
- ISSN
- 1754-5692 (ISSN-L)
- 1754-5706
- OpenAlex
- W2066542450
- Cited by
- 336
- References
- 134
- FWCI
- 19.97
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.