The DOI matches its Crossref record; 16 of the 16 references it cites were found in a registry or an index.
Evolution of Microchannel Flow Passages--Thermohydraulic Performance and Fabrication Technology
Open accessAbstract
This paper provides a roadmap of development in the thermal and fabrication aspects of microchannels as applied in microelectronics and other high heat-flux cooling applications. Microchannels are defined as flow passages that have hydraulic diameters in the range of 10 to 200 micrometers. The impetus for microchannel research was provided by the pioneering work of Tuckerman and Pease [1] at Stanford University in the early eighties. Since that time, this technology has received considerable attention in microelectronics and other major application areas, such as fuel cell systems and advanced heat sink designs. After reviewing the advancement in heat transfer technology from a historical perspective, the advantages of using microchannels in high heat flux cooling applications is discussed, and research done on various aspects of microchannel heat exchanger performance is reviewed. Single-phase performance for liquids is still expected to be describable by conventional equations; however, the gas flow may be influenced by rarefaction effects. Two-phase flow is another topic that is still under active research. The evolution of research in microchannel flow passages has paralleled the advancements made in fabrication technology. The earliest microchannels were built in silicon wafers by anisotropic wet chemical etching and sawing. While these methods have been exploited successfully, they impose a number of significant restrictions on channel geometry. A variety of advanced micromachining techniques have been developed since this early work. The current state of fabrication technology is reviewed, taxonomically organized, and found to offer many new possibilities for building microchannels. In particular anisotropic dry etching and other high aspect ratio techniques have removed many of the process-induced constraints on microchannel design. Other technologies such as surface micromachining, microstamping, hybridization, and system-on-chip integration will enable increasingly complex, highly functional heat transfer devices for the foreseeable future. It is also found that the formation of flow passages with hydraulic diameters below the microchannel regime will be readily possible with current fabrication techniques.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
High-performance heat sinking for VLSI
Tuckerman, D. B., & Pease, R. F. W. (1981) · IEEE Electron Device Letters · doi:10.1109/edl.1981.25367 · Cited by 5,291
Positioning single atoms with a scanning tunnelling microscope
Eigler, D. M., & Schweizer, E. K. (1990) · Nature · doi:10.1038/344524a0 · Cited by 3,161
Silicon as a mechanical material
Petersen, K. E. (1982) · Proceedings of the IEEE · doi:10.1109/proc.1982.12331 · Cited by 2,902
Kandlikar, S. G. (1990) · ASME Journal of Heat and Mass Transfer · doi:10.1115/1.2910348 · Cited by 1,191
Self-citationAnisotropic etching of silicon
Bean, K. E. (1978) · IEEE Transactions on Electron Devices · doi:10.1109/t-ed.1978.19250 · Cited by 803
Fluid Flow and Heat Transfer at Micro- and Meso-Scales With Application to Heat Exchanger Design
Mehendale, S. S., Jacobi, A. M., & Shah, R. K. (2000) · Applied Mechanics Reviews · doi:10.1115/1.3097347 · Cited by 537
MICROVASCULAR CONTRIBUTIONS IN TISSUE HEAT TRANSFER
Chen, M. M., & Holmes, K. R. (1980) · Annals of the New York Academy of Sciences · doi:10.1111/j.1749-6632.1980.tb50742.x · Cited by 500
Harley, J. C., Huang, Y., Bau, H. H., & Zemel, J. N. (1995) · Journal of Fluid Mechanics · doi:10.1017/s0022112095000358 · Cited by 493
Wafer direct bonding: tailoring adhesion between brittle materials
Plößl, A. (1999) · Materials Science and Engineering: R: Reports · doi:10.1016/s0927-796x(98)00017-5 · Cited by 361
Liquid transport in micron and submicron channels
Pfahler, J., Harley, J., Bau, H., & Zemel, J. (1990) · Sensors and Actuators A: Physical · doi:10.1016/0924-4247(89)80008-1 · Cited by 327
Fabrication of novel three-dimensional microstructures by the anisotropic etching of
Bassous, E. (1978) · IEEE Transactions on Electron Devices · doi:10.1109/t-ed.1978.19249 · Cited by 309
A six-wafer combustion system for a silicon micro gas turbine engine
Mehra, A., Zhang, X., Ayón, A. A., et al. (2000) · Journal of Microelectromechanical Systems · doi:10.1109/84.896774 · Cited by 223
Compensation structures for convex corner micromachining in silicon
Puers, R., & Sansen, W. (1990) · Sensors and Actuators A Physical · doi:10.1016/0924-4247(90)87085-w · Cited by 178
Kandlikar, S. G. (2002) · Heat Transfer Engineering · doi:10.1080/014576302753249570 · Cited by 159
Self-citationConstant-Wall-Temperature Nusselt Number in Micro and Nano-Channels1
Hadjiconstantinou, N. G., & Simek, O. (2001) · ASME Journal of Heat and Mass Transfer · doi:10.1115/1.1447931 · Cited by 142
Microchannels for applications in liquid dosing and flow-rate measurement
Richter, M., Woias, P., & Weiβ, D. (1997) · Sensors and Actuators A Physical · doi:10.1016/s0924-4247(97)01486-6 · Cited by 96
Cited by
Heat Transfer in Nanofluids—A Review
Das, S. K., Choi, S. U. S., & Patel, H. E. (2006) · Heat Transfer Engineering · doi:10.1080/01457630600904593 · Cited by 1,282
Single-phase convective heat transfer in microchannels: a review of experimental results
Morini, G. L. (2004) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2004.01.003 · Cited by 679
A review of entropy generation in nanofluid flow
Mahian, O., Kianifar, A., Kleinstreuer, C., Al-Nimr, M. A., Pop, I., Sahin, A. Z., & Wongwises, S. (2013) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2013.06.010 · Cited by 513
Heat Transfer Mechanisms During Flow Boiling in Microchannels
Kandlikar, S. G. (2004) · Journal of Heat Transfer · doi:10.1115/1.1643090 · Cited by 459
Self-citationSingle-phase liquid friction factors in microchannels
Steinke, M. E., & Kandlikar, S. G. (2006) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2006.01.016 · Cited by 392
Self-citation
Metadata
- Authors
- Kandlikar, S. G., & Grande, W. J.
- Venue
- Heat Transfer Engineering
- Publisher
- Informa UK Limited
- Published
- 2003-01
- Volume
- 24
- Issue
- 1
- Pages
- 3-17
- ISSN
- 0145-7632 (ISSN-L)
- 1521-0537
- OpenAlex
- W1488975872
- Cited by
- 960
- References
- 16
- FWCI
- 42.70
- Type
- journal article
- Language
- en
- Open access
- bronze
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.