The DOI matches its Crossref record; 4 of the 4 references it cites were found in a registry or an index.
Motor bearing damage detection using stator current monitoring
Abstract
This paper addresses the application of motor current spectral analysis for the detection of rolling-element bearing damage in induction machines. Vibration monitoring of mechanical bearing frequencies is currently used to detect the presence of a fault condition. Since these mechanical vibrations are associated with variations in the physical air gap of the machine, the air gap flux density is modulated and stator currents are generated at predictable frequencies related to the electrical supply and vibrational frequencies. This paper takes the initial step of investigating the efficacy of current monitoring for bearing fault detection by correlating the relationship between vibration and current frequencies caused by incipient bearing failures. The bearing failure modes are reviewed and the characteristic bearing frequencies associated with the physical construction of the bearings are defined. The effects on the stator current spectrum are described and the related frequencies determined. This is an important result in the formulation of a fault detection scheme that monitors the stator currents. Experimental results which show the vibration and current spectra of an induction machine with different bearing faults are used to verify the relationship between the vibrational and current frequencies. The test results clearly illustrate that the stator current signature can be used to identify the presence of a bearing fault.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
An Introduction to Predictive Maintenance
(2002) · Elsevier eBooks · doi:10.1016/b978-0-7506-7531-4.x5000-3 · Cited by 1,151
Report of Large Motor Reliability Survey of Industrial and Commercial Installations, Part I
(1985) · IEEE Transactions on Industry Applications · doi:10.1109/tia.1985.349532 · Cited by 602
Assessment of the Reliability of Motors in Utility Applications - Updated
Albrecht, P. F., Appiarius, J. C., McCoy, R. M., Owen, E. L., & Sharma, D. K. (1986) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.1986.4765668 · Cited by 334
Methods of Motor Current Signature Analysis
Kliman, G. B., & Stein, J. (1992) · Electric Machines & Power Systems · doi:10.1080/07313569208909609 · Cited by 330
Cited by
Condition Monitoring and Fault Diagnosis of Electrical Motors—A Review
Nandi, S., Toliyat, H. A., & Li, X. (2005) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2005.847955 · Cited by 2,382
A review of induction motors signature analysis as a medium for faults detection
El Hachemi Benbouzid, M. (2000) · IEEE Transactions on Industrial Electronics · doi:10.1109/41.873206 · Cited by 1,602
Real-Time Motor Fault Detection by 1-D Convolutional Neural Networks
Ince, T., Kiranyaz, S., Eren, L., Askar, M., & Gabbouj, M. (2016) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2016.2582729 · Cited by 1,407
Lessmeier, C., Kimotho, J. K., Zimmer, D., & Sextro, W. (2016) · PHM Society European Conference · doi:10.36001/phme.2016.v3i1.1577 · Cited by 1,268
Advances in Diagnostic Techniques for Induction Machines
Bellini, A., Filippetti, F., Tassoni, C., & Capolino, G.-A. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.2007527 · Cited by 1,140
Deep Learning Algorithms for Bearing Fault Diagnostics—A Comprehensive Review
Zhang, S., Zhang, S., Wang, B., & Habetler, T. G. (2020) · IEEE Access · doi:10.1109/access.2020.2972859 · Cited by 913
Self-citationA review on signal processing techniques utilized in the fault diagnosis of rolling element bearings
Rai, A., & Upadhyay, S. H. (2016) · Tribology International · doi:10.1016/j.triboint.2015.12.037 · Cited by 804
A generic intelligent bearing fault diagnosis system using compact adaptive 1D CNN classifier
Eren, L., Ince, T., & Kiranyaz, S. (2019) · Journal of Signal Processing Systems · doi:10.1007/s11265-018-1378-3 · Cited by 723
A Survey of Condition Monitoring and Protection Methods for Medium-Voltage Induction Motors
Zhang, P., Du, Y., Habetler, T. G., & Lu, B. (2011) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2010.2090839 · Cited by 706
Self-citationBearing fault diagnosis based on wavelet transform and fuzzy inference
Lou, X., & Loparo, K. A. (2004) · Mechanical Systems and Signal Processing · doi:10.1016/s0888-3270(03)00077-3 · Cited by 689
Online Diagnosis of Induction Motors Using MCSA
Jung, J.-H., Lee, J.-J., & Kwon, B.-H. (2006) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2006.885131 · Cited by 570
Models for Bearing Damage Detection in Induction Motors Using Stator Current Monitoring
Blodt, M., Granjon, P., Raison, B., & Rostaing, G. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.917108 · Cited by 568
Condition monitoring and fault diagnosis of electrical machines-a review
Nandi, S., & Toliyat, H. A. (2003) · Conference Record of the 1999 IEEE Industry Applications Conference. Thirty-Forth IAS Annual Meeting (Cat. No.99CH36370) · doi:10.1109/ias.1999.799956 · Cited by 531
A survey of condition monitoring and protection methods for medium voltage induction motors
Zhang, P., Du, Y., Habetler, T. G., & Lu, B. (2009) · 2009 IEEE Energy Conversion Congress and Exposition · doi:10.1109/ecce.2009.5316083 · Cited by 524
Self-citationFault Detection in Induction Machines Using Power Spectral Density in Wavelet Decomposition
Cusid�Cusido, J., Romeral, L., Ortega, J. A., Rosero, J. A., & Garc�aGarcia Espinosa, A. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2007.911960 · Cited by 512
1-D Convolutional Neural Networks for Signal Processing Applications
Kiranyaz, S., Ince, T., Abdeljaber, O., Avci, O., & Gabbouj, M. (2019) · ICASSP 2019 - 2019 IEEE International Conference on Acoustics, Speech and Signal Processing (ICASSP) · doi:10.1109/icassp.2019.8682194 · Cited by 402
Immovilli, F., Bellini, A., Rubini, R., & Tassoni, C. (2010) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2010.2049623 · Cited by 382
Condition monitoring techniques for electrical equipment-a literature survey
Han, Y., & Song, Y. H. (2003) · IEEE Transactions on Power Delivery · doi:10.1109/tpwrd.2002.801425 · Cited by 381
Benbouzid, M. E. H., Vieira, M., & Theys, C. (1999) · IEEE Transactions on Power Electronics · doi:10.1109/63.737588 · Cited by 378
Gearbox condition monitoring in wind turbines: A review
Salameh, J. P., Cauet, S., Etien, E., Sakout, A., & Rambault, L. (2018) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2018.03.052 · Cited by 376
Badihi, H., Zhang, Y., Jiang, B., Pillay, P., & Rakheja, S. (2022) · Proceedings of the IEEE · doi:10.1109/jproc.2022.3171691 · Cited by 319
Da, Y., Shi, X., & Krishnamurthy, M. (2013) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2012.2227808 · Cited by 303
Stack, J. R., Habetler, T. G., & Harley, R. G. (2004) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2004.827454 · Cited by 290
Self-citationBearing Damage Detection via Wavelet Packet Decomposition of the Stator Current
Eren, L., & Devaney, M. J. (2004) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2004.823323 · Cited by 282
Leite, V. C. M. N., Borges da Silva, J. G., Veloso, G. F. C., Borges da Silva, L. E., Lambert-Torres, G., Bonaldi, E. L., & de Lacerda de Oliveira, L. E. (2015) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2014.2345330 · Cited by 274
Frosini, L., Harlisca, C., & Szabo, L. (2015) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2014.2361115 · Cited by 264
Simulation-driven machine learning: Bearing fault classification
Sobie, C., Freitas, C., & Nicolai, M. (2018) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2017.06.025 · Cited by 256
Monitoring gear vibrations through motor current signature analysis and wavelet transform
Kar, C., & Mohanty, A. R. (2006) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2004.07.006 · Cited by 254
Frosini, L., & Bassi, E. (2010) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2009.2026770 · Cited by 254
Bearing fault detection by one-dimensional convolutional neural networks
Eren, L. (2017) · Mathematical Problems in Engineering · doi:10.1155/2017/8617315 · Cited by 250
Fault-tolerant control in variable speed drives: a survey
Campos-Delgado, D. U., Espinoza-Trejo, D. R., & Palacios, E. (2008) · IET Electric Power Applications · doi:10.1049/iet-epa:20070203 · Cited by 228
Bhuiyan, E. A., Akhand, M. M. A., Das, S. K., Ali, M. F., Tasneem, Z., Islam, M. R., Saha, D. K., Badal, F. R., Ahamed, M. H., & Moyeen, S. I. (2020) · International Journal of Automation and Computing · doi:10.1007/s11633-020-1250-3 · Cited by 68
Effect of Magnets Asymmetry on Stray Magnetic Flux Based Bearing Damage Detection in PMSM
Gurusamy, V., Baruti, K. H., Zafarani, M., Lee, W., & Akin, B. (2021) · IEEE Access · doi:10.1109/access.2021.3076779 · Cited by 28
Bearing damage diagnosis by means of the linear discriminant analysis of stator current feature
Mbo'o, C. P., & Hameyer, K. (2015) · 2015 IEEE 10th International Symposium on Diagnostics for Electrical Machines, Power Electronics and Drives (SDEMPED) · doi:10.1109/demped.2015.7303705 · Cited by 11
Metadata
- Authors
- Schoen, R. R., Habetler, T. G., Kamran, F., & Bartfield, R. G.
- Venue
- IEEE Transactions on Industry Applications
- Published
- 1995
- Volume
- 31
- Issue
- 6
- Pages
- 1274-1279
- ISSN
- 0093-9994 (ISSN-L)
- OpenAlex
- W4232447824
- Cited by
- 761
- References
- 4
- FWCI
- 3.28
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.