The DOI matches its Crossref record; 85 of the 88 references it cites were found in a registry or an index; 4 of the 45 sources its claims cite were checked for support.
Reliability of Power Electronic Systems for EV/HEV Applications
Open accessAbstract
The electrification of the transportation sector is moving on at a fast pace. All car manufacturers have strong programs to electrify their car fleet to fulfill the demands of society and customers by offering carbon-neutral technologies to bring goods and persons from one location to another. Power electronics technology is, in this evolution, essential and also in a rapid development technology-wise. Some of the introduced technologies are quite mature, and the systems designed must have high reliability as they can be quite complicated from an electrical perspective. Therefore, this article focuses on the reliability of the used power electronic systems applied in electric vehicles (EVs) and hybrid EVs (HEVs). It introduces the reliability requirements and challenges given for the power electronics applied in EV/HEV applications. Then, the advances in power electronic components to address the reliability challenges are introduced as they individually contribute to the overall system reliability. The reliability-oriented design methodology is also discussed, including two examples: an EV onboard charger and the drive train inverter. Finally, an outlook in terms of research opportunities in power electronics reliability related to EV/HEVs is provided. It can be concluded that many topics are already well handled in terms of reliability, but issues related to complete new technology introduction are important to keep the focus on.
Overview
CoChat Summary
TL;DR
This article reviews reliability requirements, challenges, component advances, and reliability-oriented design for power electronics in EV/HEV applications. It demonstrates mission-profile-based lifetime assessment for a traction inverter and an onboard charger, finding very low predicted failure probabilities before a 600,000-km service target but noting substantial modeling uncertainties.
Key findings
- Automotive reliability requirements are severe: expected operating life >10 years, ambient temperature range −55 °C to 150 °C, and zero acceptable failure rate; temperature is the major stressor (55% of stress conditions in Table 1), with active thermal cycles ΔTj ≥ 100 °C.
- In the drive-train case, a 75-kW PMSM/330-V battery/400-A, 650-V IGBT module under an EUDC profile gives B0.001 lifetimes of approximately 500,000–1,300,000 km for the transistor and 600,000–1,500,000 km for the diode (90% CI); at the 600,000-km target, failure probability is approximately 0.0004% for the transistor, 0.0002% for the diode, and 0.004% for the entire power module.
- In the OBC case, a 560-µF/400-V dc-link capacitor in a 3.3-kW single-phase OBC has a B1 lifetime of approximately 500,000–2,500,000 km (90% CI), with approximately 0.025% probability of failure before 600,000 km.
- Component advances include reports that SiC MOSFETs with conventional packaging have lower power cycling capability than Si IGBTs, next-generation automotive modules expected to reach 175 °C, and CeraLink capacitors maintaining performance up to 150 °C.
Methods
- The article is a review plus case studies using a six-step mission-profile-based reliability assessment: driving cycle and ambient conditions → mechanical power → electrical loading → electrothermal modeling → empirical lifetime models → reliability block diagram system-level reliability.
- Case studies cover an EV drive train (75-kW PMSM, 330-V battery, 400-A/650-V IGBT module, EUDC mission profile) and a 3.3-kW single-phase OBC (560-µF/400-V dc-link capacitor, standard charging profile), using Rainflow counting, the LESIT lifetime model, Weibull shape parameter β = 3, Monte Carlo simulation with 5% lifetime-coefficient variation, and 90% confidence intervals.
- Thermal modeling uses junction-to-case temperature only; the coolant temperature is assumed to be 75 °C because outer thermal-network information was limited.
Limitations
- Stated: reliability results are subject to uncertainties from environmental mission profiles, electrothermal modeling, and lifetime models, and the error margins can significantly reduce confidence in predicted lifetime; due to high uncertainty, the metrics are used for relative benchmarking rather than as direct lifetime indicators.
- Stated: vibration, dust, and contamination are not considered because of a lack of empirical lifetime models; software failures and battery technology are excluded, and the focus is limited to thermal-related wear-out of power semiconductors and capacitors.
- Stated/evident: the lack of publicly available empirical lifetime models for automotive-qualified IGBT modules led to use of the LESIT model at B10 lifetime with 50% confidence and extrapolation to lower failure probabilities; modeling only junction-to-case temperature with an assumed 75 °C coolant further limits thermal representation.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures




![Fig. 5 R&D and lifetime requirements in EV/HEV. (a) Power electronics R&D development roadmap for electric-based vehicles based on the reports in [38] and [39]. (b) Automotive lifetime requirements based on [39], * [40], ** [38], and *** [41].](https://figures.cochat.ai/paper-figures/16b2b895451544858b0fc9e372c6aefa/reliability-of-power-electronic-systems-for-ev-hev-applications-figure-5.png)
![Fig. 6 Advances in packaging elements for power modules [18].](https://figures.cochat.ai/paper-figures/41a8f71cf76147d9b1432b384fc74271/reliability-of-power-electronic-systems-for-ev-hev-applications-figure-6.png)

![Fig. 8 Typical operational mission profiles for the two subassemblies. (a) Electric vehicle driving cycle [80]. (b) Scaled-down power demand for an EV OBC (based on [81]).](https://figures.cochat.ai/paper-figures/68c177e618b44bcb9d952857c7b98b4a/reliability-of-power-electronic-systems-for-ev-hev-applications-figure-8.png)










Verification
Claims the paper makes
1 Valid · 9 Not valid · 32 Not checked · 46 Own results and interpretations
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“Besides, the ambient temperature under the hood could be as high as 100 ◦ C with high humidity [77].”
What the sources say
- Could not verifycites [77] sourceExperimental — accuracy not yet measured
The Thermal Model section treats ambient temperature as a constant model input, but does not describe conditions under a vehicle hood. Searches for 100°C ambient temperature, under-hood conditions, and humidity found no passage supporting the claimed temperature or humidity. (LLM, conf=0.74)
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“Therefore, advanced cooling technologies, such as spray cooling and jet impingement, are developed to meet the demands of the automotive industry [79].”
What the sources say
- Could not verifycites [79] sourceExperimental — accuracy not yet measured
The Introduction discusses temperature-related reliability, and Section II mentions a coolant loop for a telecom backup fuel-cell system; neither addresses automotive cooling technologies. Searches for spray cooling, jet impingement, and automotive thermal management found no passage supporting the claim. Page numbers were unavailable in our copy. (LLM, conf=0.76)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“the dc-link capacitor of the OBC has a 1% probability of failure between 500 000 and 2 500 000 km, with a 90% confidence interval.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 2 assumptions not shown here.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“However, as shown in Table 2, there is a lack of qualification standards for power semiconductor modules.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
None of the sources cited for this claim have been checked yet.
In the paper
“As can be seen from the table, temperature stress is a major stressor that destroys power electronic components.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
33 more claims
Create a free account to see all 88 claims and to verify the 2 references still open.
- Probably not a substantial claim. 42
- It may state two separate claims as one. 16
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ III. A D V A N C E S I N P O W E R E L E C T R O N I C C O M P O N E N T S T O A D D R E S S R E L I A B I L I T Y C H A L L E N G E S · p. 7
“this article focuses on the advances in power modules and capacitors only in Section III”
§ C. Cooling Assemblies and Concepts · p. 9
“## C. Cooling Assemblies and Concepts”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ B. Reliability Analysis of an Electric Vehicle Case Study · p. 10
“The overall topology configurations of the electrical drive train main inverter and the onboard EV charger for the two selected subassemblies are shown in Figs. 3 and 5, respectively.”
§ A. Power Modules · p. 8
“Fig. 5. R&D and lifetime requirements in EV/HEV.”
Citations
Cites
An Industry-Based Survey of Reliability in Power Electronic Converters
Yang, S., Bryant, A., Mawby, P., Xiang, D., Ran, L., & Tavner, P. (2011) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2011.2124436 · Cited by 2,019
Handbook of software reliability engineering
Lyu, M. R.-T. (1996) · McGraw-Hill, Inc. eBooks · Cited by 1,592
Electrical Machines and Drives for Electric, Hybrid, and Fuel Cell Vehicles
Zhu, Z. Q., & Howe, D. (2007) · Proceedings of the IEEE · doi:10.1109/jproc.2006.892482 · Cited by 1,547 · cited 1×
“Intensive research and development are currently going on enhancing PM EMs and adopting different types of EMs in order to further improve the performance of future electric-based vehicles [48].”
MethodEmadi, A., Lee, Y. J., & Rajashekara, K. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.922768 · Cited by 1,461 · cited 1×
“Notably, different possible configurations for the power train in EV/HEV can be found in the automotive market [25]–[28].”
BackgroundReliability of Capacitors for DC-Link Applications in Power Electronic Converters—An Overview
Wang, H., & Blaabjerg, F. (2014) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2014.2308357 · Cited by 1,384 · cited 3×
“Besides active components, the capacitor reliability is also essential to understand and take into consideration when doing reliability analysis for the complete system [20].”
BackgroundInfluentialSelf-citationModern Electric, Hybrid Electric, and Fuel Cell Vehicles: Fundamentals, Theory, and Design
Ehsani, M., Gao, Y., Gay, S. E., & Emadi, A. (2004) · CRC Press eBooks · doi:10.1201/9781420037739 · Cited by 1,248
Closed-loop optimization of fast-charging protocols for batteries with machine learning
Attia, P. M., Grover, A., Jin, N., Severson, K. A., Markov, T. M., Liao, Y.-H., Chen, M. H., Cheong, B., Perkins, N., Yang, Z., et al. (2020) · Nature · doi:10.1038/s41586-020-1994-5 · Cited by 1,180
Toward Reliable Power Electronics: Challenges, Design Tools, and Opportunities
Wang, H., Liserre, M., & Blaabjerg, F. (2013) · IEEE Industrial Electronics Magazine · doi:10.1109/mie.2013.2252958 · Cited by 916 · cited 1×
“knowledge base (physics of failure), a design stage (DfR and robustness validation), and an operational phase (intelligent control and condition monitoring) [10]–[12].”
BackgroundSelf-citationThe Essence of Three-Phase PFC Rectifier Systems—Part I
Kolar, J. W., & Friedli, T. (2013) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2012.2197867 · Cited by 788 · cited 1×
“Notably, depending on the topology, the HV dc bus voltage will be different [32], [33].”
BackgroundPractical Reliability Engineering
O'Connor, P. D. T., & Kleyner, A. (2011) · Wiley eBooks · doi:10.1002/9781119961260 · Cited by 783
Research works printed but not linked: 21
- 2018, The Roadmap Report Towards 2040 A Guide to Automotive Propulsion Technologies
- 2018, Shaping Future Electromobility With Semiconductor Innovations
- 2015, Handbook for Robustness Validation of Semiconductor Devices in Automotive Applications
- ehsani, 2018, Modern Electric Hybrid Electric and Fuel Cell Vehicles
- drexhage, 2016, Effect of humidity and condensation on power electronics systems
- 2013, Electric and Electronic Components in Motor Vehicles up to 3 5t
- 2020, Electric vehicle outlook 2020
- 2013, Failure Mechanism Based Stress Test Qualification for Discrete Semiconductors in Automotive Applications REV D1
- 2017, Electrical and electronics technical team roadmap
- 2008, Vorlesung Qualtat und Zuverlassigkeit von Fahrzeug e/e Hardware an der tu Berlin
- 2010, Stress Test Qualification for Passive Components
- 2013, Zvei Die Elektroindustrie Handbook for Robustness Validation of Automotive Electrical/Electronic Modules
- allouche, 2020, Hitachi DSC Power Module From Audi e-Tron Inverter
- christmann, 2009, Reliability of power modules in hybrid vehicles, Proc PCIM Eur, 359
- 2019, Qualification of Power Modules for Use in Power Electron Converter Units in Motor Vehicles
- ishihara, 2012, New transfer-mold power module series for automotive power-train inverters, Proc PCIM Eur, 1408
- ishihara, 2014, New compact-package power modules for electric and hybrid vehicles (J1 series), Proc PCIM Eur, 1093
- kimura, 2014, High-power-density inverter technology for hybrid and electric vehicle applications, Hitachi Rev, 63, 41
- knappik, 2019, The advantages of 48-volt vehicle electronics, Veh Technol
- 2005, Standard Practices for Cycle Counting in Fatigue Analysis
- wintrich, 2015, Application Manual Power Semiconductors
Cited by
Research Development on Aqueous Ammonium‐Ion Batteries
Zhang, R., Wang, S., Chou, S., & Jin, H. (2022) · Advanced Functional Materials · doi:10.1002/adfm.202112179 · Cited by 172
Ullah, Z., Wang, S., Wu, G., Hasanien, H. M., Rehman, A. U., Turky, R. A., & Elkadeem, M. R. (2022) · Energy · doi:10.1016/j.energy.2022.126560 · Cited by 157
Ten questions concerning active noise control in the built environment
Lam, B., Gan, W., Shi, D., Nishimura, M., & Elliott, S. J. (2021) · Building and Environment · doi:10.1016/j.buildenv.2021.107928 · Cited by 150
“Increased electrification of automobiles have also improved the longevity of automotive electronics to meet the expected operating life of more than ten years [160], providing a reliable infrastructure for digital ANC applications [18,156].”
BackgroundRahman, S. M. I., Moghassemi, A., Arsalan, A., Timilsina, L., Chamarthi, P. K., Papari, B., Özkan, G., & Edrington, C. S. (2024) · IEEE Access · doi:10.1109/access.2024.3385429 · Cited by 167
“The high voltage high-power PECs used in EVs face a harsh environment due to the strict operating conditions [268].”
BackgroundArtificial-Intelligence-Based Design for Circuit Parameters of Power Converters
Li, X., Zhang, X., Lin, F., et al. (2021) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2021.3088377 · Cited by 107
“And efficiency, size, cost, reliability, ripples, and transient response are several commonlyadopted design objectives [7]–[10].”
BackgroundSelf-citation
Metadata
- Authors
- Blaabjerg, F., Wang, H., Vernica, I., Liu, B., & Davari, P.
- Affiliations
- Aalborg University (DK)
- Venue
- Proceedings of the IEEE
- Published
- 2021-06
- Volume
- 109
- Issue
- 6
- Pages
- 1060-1076
- ISSN
- 0018-9219 (ISSN-L)
- 1558-2256
- OpenAlex
- W3095570029
- Cited by
- 249
- References
- 88
- Citations by year
- 2026: 35 · 2025: 57 · 2024: 67 · 2023: 52 · 2022: 23 · 2021: 15
- FWCI
- 7.72
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Locations
- Proceedings of the IEEE (publishedVersion, cc-by)
- VBN Forskningsportal (Aalborg Universitet) (publishedVersion, cc-by)
- Funders
- VILLUM FONDEN under the VILLUM Investigators (00016591)
- Innovation Fund Denmark through the Advanced Power Electronic Technology and Tools Project
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Silicon Carbide Semiconductor Technologies
- Physical Sciences › Engineering › Automotive Engineering › Electric and Hybrid Vehicle Technologies
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Electric Power Systems and Control
- Keywords
- power electronics reliability, electric vehicles, hybrid electric vehicles, reliability requirements, power electronic components, reliability-oriented design, on-board charger, inverter, vehicle electrification
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Reliability of Power Electronic Systems for EV/HEV Applications. https://app.cochat.ai/papers/10.1109/jproc.2020.3031041
- The paper
- Blaabjerg, F., Wang, H., Vernica, I., Liu, B., & Davari, P. (2021). Reliability of Power Electronic Systems for EV/HEV Applications. Proceedings of the IEEE. https://doi.org/10.1109/jproc.2020.3031041
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.