Reliability of Power Electronic Systems for EV/HEV Applications
Open accessThe DOI matches its Crossref record; 85 of the 88 references it cites were found in a registry or an index; 4 of the 45 sources its claims cite were checked for support.
Abstract
The electrification of the transportation sector is moving on at a fast pace. All car manufacturers have strong programs to electrify their car fleet to fulfill the demands of society and customers by offering carbon-neutral technologies to bring goods and persons from one location to another. Power electronics technology is, in this evolution, essential and also in a rapid development technology-wise. Some of the introduced technologies are quite mature, and the systems designed must have high reliability as they can be quite complicated from an electrical perspective. Therefore, this article focuses on the reliability of the used power electronic systems applied in electric vehicles (EVs) and hybrid EVs (HEVs). It introduces the reliability requirements and challenges given for the power electronics applied in EV/HEV applications. Then, the advances in power electronic components to address the reliability challenges are introduced as they individually contribute to the overall system reliability. The reliability-oriented design methodology is also discussed, including two examples: an EV onboard charger and the drive train inverter. Finally, an outlook in terms of research opportunities in power electronics reliability related to EV/HEVs is provided. It can be concluded that many topics are already well handled in terms of reliability, but issues related to complete new technology introduction are important to keep the focus on.
Overview
CoChat Summary
TL;DR
This article reviews reliability requirements, challenges, component advances, and reliability-oriented design for power electronics in EV/HEV applications. It demonstrates mission-profile-based lifetime assessment for a traction inverter and an onboard charger, finding very low predicted failure probabilities before a 600,000-km service target but noting substantial modeling uncertainties.
Key findings
- Automotive reliability requirements are severe: expected operating life >10 years, ambient temperature range −55 °C to 150 °C, and zero acceptable failure rate; temperature is the major stressor (55% of stress conditions in Table 1), with active thermal cycles ΔTj ≥ 100 °C.
- In the drive-train case, a 75-kW PMSM/330-V battery/400-A, 650-V IGBT module under an EUDC profile gives B0.001 lifetimes of approximately 500,000–1,300,000 km for the transistor and 600,000–1,500,000 km for the diode (90% CI); at the 600,000-km target, failure probability is approximately 0.0004% for the transistor, 0.0002% for the diode, and 0.004% for the entire power module.
- In the OBC case, a 560-µF/400-V dc-link capacitor in a 3.3-kW single-phase OBC has a B1 lifetime of approximately 500,000–2,500,000 km (90% CI), with approximately 0.025% probability of failure before 600,000 km.
- Component advances include reports that SiC MOSFETs with conventional packaging have lower power cycling capability than Si IGBTs, next-generation automotive modules expected to reach 175 °C, and CeraLink capacitors maintaining performance up to 150 °C.
Methods
- The article is a review plus case studies using a six-step mission-profile-based reliability assessment: driving cycle and ambient conditions → mechanical power → electrical loading → electrothermal modeling → empirical lifetime models → reliability block diagram system-level reliability.
- Case studies cover an EV drive train (75-kW PMSM, 330-V battery, 400-A/650-V IGBT module, EUDC mission profile) and a 3.3-kW single-phase OBC (560-µF/400-V dc-link capacitor, standard charging profile), using Rainflow counting, the LESIT lifetime model, Weibull shape parameter β = 3, Monte Carlo simulation with 5% lifetime-coefficient variation, and 90% confidence intervals.
- Thermal modeling uses junction-to-case temperature only; the coolant temperature is assumed to be 75 °C because outer thermal-network information was limited.
Limitations
- Stated: reliability results are subject to uncertainties from environmental mission profiles, electrothermal modeling, and lifetime models, and the error margins can significantly reduce confidence in predicted lifetime; due to high uncertainty, the metrics are used for relative benchmarking rather than as direct lifetime indicators.
- Stated: vibration, dust, and contamination are not considered because of a lack of empirical lifetime models; software failures and battery technology are excluded, and the focus is limited to thermal-related wear-out of power semiconductors and capacitors.
- Stated/evident: the lack of publicly available empirical lifetime models for automotive-qualified IGBT modules led to use of the LESIT model at B10 lifetime with 50% confidence and extrapolation to lower failure probabilities; modeling only junction-to-case temperature with an assumed 75 °C coolant further limits thermal representation.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures




![Fig. 5 R&D and lifetime requirements in EV/HEV. (a) Power electronics R&D development roadmap for electric-based vehicles based on the reports in [38] and [39]. (b) Automotive lifetime requirements based on [39], * [40], ** [38], and *** [41].](https://figures.cochat.ai/paper-figures/16b2b895451544858b0fc9e372c6aefa/reliability-of-power-electronic-systems-for-ev-hev-applications-figure-5.png)
![Fig. 6 Advances in packaging elements for power modules [18].](https://figures.cochat.ai/paper-figures/41a8f71cf76147d9b1432b384fc74271/reliability-of-power-electronic-systems-for-ev-hev-applications-figure-6.png)

![Fig. 8 Typical operational mission profiles for the two subassemblies. (a) Electric vehicle driving cycle [80]. (b) Scaled-down power demand for an EV OBC (based on [81]).](https://figures.cochat.ai/paper-figures/68c177e618b44bcb9d952857c7b98b4a/reliability-of-power-electronic-systems-for-ev-hev-applications-figure-8.png)










Verification
Claims the paper makes
1 Valid · 9 Not valid · 32 Not checked · 46 Own results and interpretations
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“Besides, the ambient temperature under the hood could be as high as 100 ◦ C with high humidity [77].”
What the sources say
- Could not verifycites [77] sourceExperimental — accuracy not yet measured
The Thermal Model section treats ambient temperature as a constant model input, but does not describe conditions under a vehicle hood. Searches for 100°C ambient temperature, under-hood conditions, and humidity found no passage supporting the claimed temperature or humidity. (LLM, conf=0.74)
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“Therefore, advanced cooling technologies, such as spray cooling and jet impingement, are developed to meet the demands of the automotive industry [79].”
What the sources say
- Could not verifycites [79] sourceExperimental — accuracy not yet measured
The Introduction discusses temperature-related reliability, and Section II mentions a coolant loop for a telecom backup fuel-cell system; neither addresses automotive cooling technologies. Searches for spray cooling, jet impingement, and automotive thermal management found no passage supporting the claim. Page numbers were unavailable in our copy. (LLM, conf=0.76)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“the dc-link capacitor of the OBC has a 1% probability of failure between 500 000 and 2 500 000 km, with a 90% confidence interval.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 2 assumptions not shown here.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“However, as shown in Table 2, there is a lack of qualification standards for power semiconductor modules.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
None of the sources cited for this claim have been checked yet.
In the paper
“As can be seen from the table, temperature stress is a major stressor that destroys power electronic components.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
33 more claims
Create a free account to see all 88 claims and to verify the 2 references still open.
- Probably not a substantial claim. 42
- It may state two separate claims as one. 16
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ III. A D V A N C E S I N P O W E R E L E C T R O N I C C O M P O N E N T S T O A D D R E S S R E L I A B I L I T Y C H A L L E N G E S · p. 7
“this article focuses on the advances in power modules and capacitors only in Section III”
§ C. Cooling Assemblies and Concepts · p. 9
“## C. Cooling Assemblies and Concepts”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ B. Reliability Analysis of an Electric Vehicle Case Study · p. 10
“The overall topology configurations of the electrical drive train main inverter and the onboard EV charger for the two selected subassemblies are shown in Figs. 3 and 5, respectively.”
§ A. Power Modules · p. 8
“Fig. 5. R&D and lifetime requirements in EV/HEV.”
Citations
Cites
An Industry-Based Survey of Reliability in Power Electronic Converters
Yang, S., Bryant, A., Mawby, P., Xiang, D., Ran, L., & Tavner, P. (2011) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2011.2124436 · Cited by 2,019
Handbook of software reliability engineering
Lyu, M. R.-T. (1996) · McGraw-Hill, Inc. eBooks · Cited by 1,592
Electrical Machines and Drives for Electric, Hybrid, and Fuel Cell Vehicles
Zhu, Z. Q., & Howe, D. (2007) · Proceedings of the IEEE · doi:10.1109/jproc.2006.892482 · Cited by 1,547 · cited 1×
“Intensive research and development are currently going on enhancing PM EMs and adopting different types of EMs in order to further improve the performance of future electric-based vehicles [48].”
MethodEmadi, A., Lee, Y. J., & Rajashekara, K. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.922768 · Cited by 1,461 · cited 1×
“Notably, different possible configurations for the power train in EV/HEV can be found in the automotive market [25]–[28].”
BackgroundReliability of Capacitors for DC-Link Applications in Power Electronic Converters—An Overview
Wang, H., & Blaabjerg, F. (2014) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2014.2308357 · Cited by 1,384 · cited 3×
“Besides active components, the capacitor reliability is also essential to understand and take into consideration when doing reliability analysis for the complete system [20].”
BackgroundInfluentialSelf-citationModern Electric, Hybrid Electric, and Fuel Cell Vehicles: Fundamentals, Theory, and Design
Ehsani, M., Gao, Y., Gay, S. E., & Emadi, A. (2004) · CRC Press eBooks · doi:10.1201/9781420037739 · Cited by 1,248
Closed-loop optimization of fast-charging protocols for batteries with machine learning
Attia, P. M., Grover, A., Jin, N., Severson, K. A., Markov, T. M., Liao, Y.-H., Chen, M. H., Cheong, B., Perkins, N., Yang, Z., et al. (2020) · Nature · doi:10.1038/s41586-020-1994-5 · Cited by 1,180
Toward Reliable Power Electronics: Challenges, Design Tools, and Opportunities
Wang, H., Liserre, M., & Blaabjerg, F. (2013) · IEEE Industrial Electronics Magazine · doi:10.1109/mie.2013.2252958 · Cited by 916 · cited 1×
“knowledge base (physics of failure), a design stage (DfR and robustness validation), and an operational phase (intelligent control and condition monitoring) [10]–[12].”
BackgroundSelf-citationThe Essence of Three-Phase PFC Rectifier Systems—Part I
Kolar, J. W., & Friedli, T. (2013) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2012.2197867 · Cited by 788 · cited 1×
“Notably, depending on the topology, the HV dc bus voltage will be different [32], [33].”
BackgroundPractical Reliability Engineering
O'Connor, P. D. T., & Kleyner, A. (2011) · Wiley eBooks · doi:10.1002/9781119961260 · Cited by 783
Efficiency-Optimized High-Current Dual Active Bridge Converter for Automotive Applications
Krismer, F., & Kolar, J. W. (2012) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2011.2112312 · Cited by 747 · cited 2×
“Due to the safety requirements, the dc–dc converter should isolate the power grid from the HV dc bus and the HV dc bus from the LV dc bus [34], [35].”
BackgroundMethodTransitioning to Physics-of-Failure as a Reliability Driver in Power Electronics
Wang, H., Liserre, M., Blaabjerg, F., de Place Rimmen, P., Jacobsen, J. B., Kvisgaard, T., & Landkildehus, J. (2014) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2013.2290282 · Cited by 693 · cited 1×
“In past decades, a paradigm shift from the conventional statistics-based reliability evaluation procedures toward a PoF-based lifetime estimation of power electronics has been gaining more attraction [11].”
BackgroundSelf-citationDistributed Power-Generation Systems and Protection
Blaabjerg, F., Yang, Y., Yang, D., & Wang, X. (2017) · Proceedings of the IEEE · doi:10.1109/jproc.2017.2696878 · Cited by 671 · cited 2×
“I N T R O D U C T I O N The electrification of modern society is evolving at a very rapid pace to make the society more efficient and sustainable and reduces carbon footprint—the electrical generation needs to be renewable-based [1], the electrical transmission and distribution systems are expanded, and all aspects of…”
BackgroundSelf-citationA reference book of driving cycles for use in the measurement of road vehicle emissions
Barlow, T. J., Latham, S. R., McCrae, I. S., & Boulter, P. G. (2009) · Project report - Transport Research Laboratory · Cited by 659
Global Trends in High-Power On-Board Chargers for Electric Vehicles
Khaligh, A., & D'Antonio, M. (2019) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2019.2897050 · Cited by 652 · cited 3×
“For instance, Renault Zoe uses an integrated Chameleon charger rated up to 43 kW [23], [30].”
BackgroundMethodFast power cycling test of IGBT modules in traction application
Held, M., Jacob, P., Nicoletti, G., Scacco, P., & Poech, M.-H. (2002) · Proceedings of Second International Conference on Power Electronics and Drive Systems · doi:10.1109/peds.1997.618742 · Cited by 585
A Review of SiC Power Module Packaging Technologies: Challenges, Advances, and Emerging Issues
Lee, H., Smet, V., & Tummala, R. (2020) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2019.2951801 · Cited by 526 · cited 5×
“6 shows the respective advances in packaging elements for interconnection, substrate, and die attach of power modules, as presented in [18].”
BackgroundInfluentialOh, H., Han, B., McCluskey, P., Han, C., & Youn, B. D. (2015) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2014.2346485 · Cited by 513 · cited 1×
“, junction temperature) and health conditions of power modules are of high interest [14]–[16].”
BackgroundMa, K., Liserre, M., Blaabjerg, F., & Kerekes, T. (2015) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2014.2312335 · Cited by 460
Self-citationThe Essence of Three-Phase PFC Rectifier Systems—Part II
Friedli, T., Hartmann, M., & Kolar, J. W. (2014) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2013.2258472 · Cited by 457
Making the Case for Electrified Transportation
Bilgin, B., Magne, P., Malysz, P., Yang, Y., Pantelic, V., Preindl, M., Korobkine, A., Jiang, W., Lawford, M., & Emadi, A. (2015) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2015.2437338 · Cited by 455 · cited 1×
“The EMs utilized in today’s EV/HEV are commonly ac induction machine or ac permanent magnet (PM) type [46], [47].”
MethodSurvey of High-Temperature Reliability of Power Electronics Packaging Components
Khazaka, R., Mendizabal, L., Henry, D., & Hanna, R. (2015) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2014.2357836 · Cited by 386 · cited 1×
“Using wide bandgap devices and new packaging technologies [17], [18], which are being adapted to the transportation sector and their reliability requirements, is also important.”
BackgroundAutomotive Traction Inverters: Current Status and Future Trends
Reimers, J., Dorn-Gomba, L., Mak, C., & Emadi, A. (2019) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2019.2897899 · Cited by 375 · cited 2×
“The EMs utilized in today’s EV/HEV are commonly ac induction machine or ac permanent magnet (PM) type [46], [47].”
BackgroundMethodActive thermal control of power electronic modules
Murdock, D. A., Torres, J. E. R., Connors, J. J., & Lorenz, R. D. (2006) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2005.863905 · Cited by 332 · cited 1×
“Active thermal controls are based on two principles: first, minimizing the power dissipation through switching and conduction loss reduction; second, by rerouting the flowing path of the current among the power devices [55], [56]; both cases can be achieved through suitable selection of the modulation strategy and rea…”
BackgroundOverview of Real-Time Lifetime Prediction and Extension for SiC Power Converters
Ni, Z., Lyu, X., Yadav, O. P., Singh, B. N., Zheng, S., & Cao, D. (2020) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2019.2962503 · Cited by 261 · cited 1×
“Chip- and packaging-level failure mechanisms, testing, and condition monitoring health indicators of SiC/GaN devices are also attractive topics [19].”
BackgroundAn Efficient Implementation of the Rainflow Counting Algorithm for Life Consumption Estimation
Musallam, M., & Johnson, C. M. (2012) · IEEE Transactions on Reliability · doi:10.1109/tr.2012.2221040 · Cited by 259 · cited 1×
“This is done with the help of a Rainflow counting algorithm [94], [95].”
MethodA High-Efficiency High-Density Wide-Bandgap Device-Based Bidirectional On-Board Charger
Li, B., Li, Q., Lee, F. C., Liu, Z., & Yang, Y. (2018) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2018.2845846 · Cited by 259 · cited 2×
“is moving toward bidirectional charging, where EV/HEV can support the power grid by feeding the battery power back to the grid [31].”
BackgroundMethodHybrid electric vehicles principles and applications with practical perspectives
Mi, C. C., Masrur, M. A., & Gao, W. (2011) · Cited by 253
Power Cycling Reliability of Power Module: A Survey
Durand, C., Klingler, M., Coutellier, D., & Naceur, H. (2016) · IEEE Transactions on Device and Materials Reliability · doi:10.1109/tdmr.2016.2516044 · Cited by 239 · cited 1×
“Power cycling testing of power modules is essential to understand the wear out of the power components, when they are in operation, and predict when failures might occur [13], for example, through degradation.”
BackgroundImproved Reliability of Power Modules: A Review of Online Junction Temperature Measurement Methods
Baker, N., Liserre, M., Dupont, L., & Avenas, Y. (2014) · IEEE Industrial Electronics Magazine · doi:10.1109/mie.2014.2312427 · Cited by 232 · cited 1×
“, junction temperature) and health conditions of power modules are of high interest [14]–[16].”
BackgroundSangwongwanich, A., Yang, Y., Sera, D., & Blaabjerg, F. (2018) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2017.2678169 · Cited by 231 · cited 1×
“, wind power converters [84], grid-connected PV inverters [85], variable frequency drives [86], or more electric aircraft [87]).”
BackgroundSelf-citationModeling and optimization of bidirectional dual active bridge DC-DC converter topologies
Krismer, F. (2010) · Repository for Publications and Research Data (ETH Zurich) · doi:10.3929/ethz-a-006395373 · Cited by 230
Power Electronics Reliability: State of the Art and Outlook
Wang, H., & Blaabjerg, F. (2021) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2020.3037161 · Cited by 218
Self-citationReliability Prediction for Inverters in Hybrid Electrical Vehicles
Hirschmann, D., Tissen, D., Schroder, S., & De Doncker, R. W. (2007) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2007.909236 · Cited by 209
Zhou, D., Wang, H., & Blaabjerg, F. (2018) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2017.2769161 · Cited by 200 · cited 1×
“Assuming that all six transistors and all six diodes of the IGBT power module have the same reliable performance as the upper transistor/diode pair (T1/D1), the RBD analysis [98] is used to merge the reliability information of each device and to calculate the unreliability curve of the IGBT power module.”
MethodSelf-citationComplete Loss and Thermal Model of Power Semiconductors Including Device Rating Information
Ma, K., Bahman, A. S., Beczkowski, S., & Blaabjerg, F. (2015) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2014.2352341 · Cited by 199 · cited 1×
“Average switching cycle power loss models [91], [92] are first used to calculate the total losses (e.”
MethodSelf-citationFrequency-Domain Thermal Modeling and Characterization of Power Semiconductor Devices
Ma, K., He, N., Liserre, M., & Blaabjerg, F. (2016) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2015.2509506 · Cited by 193
Self-citationReliability of Power Electronic Converter Systems
(2015) · Institution of Engineering and Technology eBooks · doi:10.1049/pbpo080e · Cited by 190 · cited 1×
“knowledge base (physics of failure), a design stage (DfR and robustness validation), and an operational phase (intelligent control and condition monitoring) [10]–[12].”
BackgroundLifetime Estimation of DC-Link Capacitors in Adjustable Speed Drives Under Grid Voltage Unbalances
Wang, H., Davari, P., Wang, H., Kumar, D., Zare, F., & Blaabjerg, F. (2019) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2018.2863701 · Cited by 179 · cited 3×
“Considering the empirical lifetime model presented in [86] and a 5% variation in its coefficients, the capacitor’s B1 lifetime distribution is”
BackgroundMethodSelf-citationMusallam, M., Yin, C., Bailey, C., & Johnson, M. (2015) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2014.2358555 · Cited by 168 · cited 1×
“Average switching cycle power loss models [91], [92] are first used to calculate the total losses (e.”
MethodMa, K., Wang, H., & Blaabjerg, F. (2016) · IEEE Power Electronics Magazine · doi:10.1109/mpel.2016.2615277 · Cited by 168 · cited 2×
“On the other hand, for hardware wear-out failures, a more realistic reliability assessment procedure can be carried out based on the Design for Reliability (DfR) [7] and Physics-of-Failure (PoF) [8], complementing conventional reliability methods.”
MethodSelf-citationAnalysis of PWM Frequency Control to Improve the Lifetime of PWM Inverter
Wei, L., McGuire, J., & Lukaszewski, R. A. (2011) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2010.2103391 · Cited by 160 · cited 1×
“Active thermal controls are based on two principles: first, minimizing the power dissipation through switching and conduction loss reduction; second, by rerouting the flowing path of the current among the power devices [55], [56]; both cases can be achieved through suitable selection of the modulation strategy and rea…”
BackgroundPhysics-of-Failure: An Approach to Reliable Product Development
Pecht, M., & Dasgupta, A. (1995) · Journal of the IEST · doi:10.17764/jiet.2.38.5.y3561m03801h0082 · Cited by 140
Bryant, A. T., Mawby, P. A., Palmer, P. R., Santi, E., & Hudgins, J. L. (2008) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2008.921388 · Cited by 139
Reliability challenges of automotive power electronics
Scheuermann, U. (2009) · Microelectronics Reliability · doi:10.1016/j.microrel.2009.06.045 · Cited by 121 · cited 2×
“Passive thermal cycles may cause higher stress on the power devices [51].”
BackgroundPower cycling methods for SiC MOSFETs
Herold, C., Sun, J., Seidel, P., Tinschert, L., & Lutz, J. (2017) · 2017 29th International Symposium on Power Semiconductor Devices and IC's (ISPSD) · doi:10.23919/ispsd.2017.7988994 · Cited by 117
Condition Monitoring: A Decade of Proposed Techniques
Avenas, Y., Dupont, L., Baker, N., Zara, H., & Barruel, F. (2015) · IEEE Industrial Electronics Magazine · doi:10.1109/mie.2015.2481564 · Cited by 107
Mi, C. C., & Masrur, M. A. (2017) · Wiley eBooks · doi:10.1002/9781118970553 · Cited by 107
Reliability-Oriented Design of Three-Phase Power Converters for Aircraft Applications
Burgos, R., Chen, G., Wang, F., Boroyevich, D., Odendaal, W. G., & Van Wyk, J. D. (2012) · IEEE Transactions on Aerospace and Electronic Systems · doi:10.1109/taes.2012.6178060 · Cited by 87 · cited 1×
“, wind power converters [84], grid-connected PV inverters [85], variable frequency drives [86], or more electric aircraft [87]).”
BackgroundMethodology for Active Thermal Cycle Reduction of Power Electronic Modules
van der Broeck, C. H., Ruppert, L. A., Lorenz, R. D., & De Doncker, R. W. (2019) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2018.2882184 · Cited by 85 · cited 1×
“To minimize the thermal swings due to active power cycling, active thermal control methods can be applied [52]–[54].”
MethodReview of active thermal and lifetime control techniques for power electronic modules
Andresen, M., Liserre, M., & Buticchi, G. (2014) · 2014 16th European Conference on Power Electronics and Applications · doi:10.1109/epe.2014.6910822 · Cited by 81 · cited 1×
“For the manufacturers, enhancing the interconnections between chips is a potential choice to delay the bond wire liftoff [63].”
BackgroundFuture of electric vehicle charging
Mouli, G. R. C., Venugopal, P., & Bauer, P. (2017) · International Symposium on Power Electronics (Ee) · doi:10.1109/pee.2017.8171657 · Cited by 74
Liu, B., Davari, P., & Blaabjerg, F. (2019) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2019.2956323 · Cited by 67
Self-citationReliability of Power Electronic Converter Systems
Chung, H. S.-H., Wang, H., Blaabjerg, F., & PECHT, M. G. (2024) · doi:10.1049/pbpo261e · Cited by 64
Self-citationWang, Y., Jones, S., Dai, A., & Liu, G. (2014) · Microelectronics Reliability · doi:10.1016/j.microrel.2014.07.037 · Cited by 63 · cited 1×
“, thermal grease, case, and coolant), only the junction-to-case temperature is modeled, while the coolant temperature is assumed to be 75 ◦C [70].”
BackgroundReview of Recent Activities on Dielectric Films for Capacitor Applications
Qi, L., Petersson, L., & Liu, T. (2014) · Journal of International Council on Electrical Engineering · doi:10.5370/jicee.2014.4.1.001 · Cited by 60 · cited 1×
“First, at the material level, research activities on dielectric films to increase energy density and upper temperature limits of existing film capacitors are discussed in [74].”
BackgroundMulti-port multi-cell DC/DC converter topology for electric vehicle's power distribution networks
Schäfer, J., Bortis, D., & Kolar, J. W. (2017) · IEEE ... Workshop on Control and Modeling for Power Electronics · doi:10.1109/compel.2017.8013326 · Cited by 51 · cited 1×
“2 shows a block diagram of a typical electrical power system architecture in EV/HEV, including the major power electronic systems that can be found in an electric-based vehicle [23], [24].”
BackgroundActive Thermal Control of GaN-Based DC/DC Converter
Prasobhu, P. K., Raveendran, V., Buticchi, G., & Liserre, M. (2018) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2018.2809543 · Cited by 50 · cited 1×
“To minimize the thermal swings due to active power cycling, active thermal control methods can be applied [52]–[54].”
MethodReliability prediction for inverters in hybrid electrical vehicles
Hirschmann, D., Tissen, D., Schröder, S., & Doncker, R. W. D. (2006) · IEEE Power Electronics Specialists Conference (PESC) · doi:10.1109/pesc.2006.1712078 · Cited by 48
Wang, Z., Liu, B., Guan, L., Zhang, Y., Cheng, M., Zhang, B., & Xu, L. (2019) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2018.2879869 · Cited by 40 · cited 1×
“Due to their higher power capabilities, in some EV/HEV applications, the main inverter is reused for OBC, which are referred to as onboard integrated chargers or propulsionsystem-integrated OBCs [30], [49].”
BackgroundSelf-citationDaily EV load profile of an EV charging station at business premises
Islam, M. S., & Mithulananthan, N. (2016) · IEEE Innovative Smart Grid Technologies-Asia · doi:10.1109/isgt-asia.2016.7796485 · Cited by 38
Nonlinear $C_{oss}-V_{DS}$ Profile Based ZVS Range Calculation for Dual Active Bridge Converters
Liu, B., Davari, P., & Blaabjerg, F. (2021) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2020.3003248 · Cited by 35
Self-citationHaumann, S., Rudzki, J., Osterwald, F., Becker, M., & Eisele, R. (2013) · 2013 Twenty-Eighth Annual IEEE Applied Power Electronics Conference and Exposition (APEC) · doi:10.1109/apec.2013.6520275 · Cited by 34 · cited 1×
“Relevant techniques include heavy copper wire bonding, sintered connections, and buffer layers between different materials [64], [65].”
BackgroundEvaluation and Design Tools for the Reliability of Wind Power Converter System
Ma, K., Zhou, D., & Blaabjerg, F. (2015) · Journal of Power Electronics · doi:10.6113/jpe.2015.15.5.1149 · Cited by 34 · cited 1×
“In addition, the DfR method, which is defined as the process carried out during early product development stages to ensure certain reliability and quality targets, is used alongside the PoF concept [7], [83].”
MethodSelf-citationMi, C. C., Peng, F. Z., Kelly, K. J., O'Keefe, M., & Hassani, V. (2008) · International Journal of Electric and Hybrid Vehicles · doi:10.1504/ijehv.2008.019901 · Cited by 28
Electric-Vehicle Power Converters Model-Based Design-for-Reliability
University of Parma, Soldati, A., Pietrini, G., University of Parma, Dalboni, M., University of Parma, Concari, C., & University of Parma (2018) · CPSS Transactions on Power Electronics and Applications · doi:10.24295/cpsstpea.2018.00010 · Cited by 28
A breakthrough in power electronics reliability — New die attach and wire bonding materials
Krebs, T., Duch, S., Schmitt, W., Koetter, S., Prenosil, P., & Thomas, S. (2013) · IEEE Electronic Components and Technology Conference (ECTC) · doi:10.1109/ectc.2013.6575811 · Cited by 27 · cited 1×
“Relevant techniques include heavy copper wire bonding, sintered connections, and buffer layers between different materials [64], [65].”
BackgroundDC link bus design for high frequency, high temperature converters
Stewart, J., Neely, J., Delhotal, J., & Flicker, J. (2017) · 2017 IEEE Applied Power Electronics Conference and Exposition (APEC) · doi:10.1109/apec.2017.7930789 · Cited by 25 · cited 1×
“Third, at the application level, design strategies for low-inductive dc-link capacitor bank design are developed for the trend of using an increasing switching frequency [75].”
MethodElectric and hybrid vehicle power electronics efficiency, testing and reliability
Drobnik, J., & Jain, P. K. (2013) · World Electric Vehicle Symposium and Exhibition (EVS) · doi:10.1109/evs.2013.6915002 · Cited by 22 · cited 1×
“Notably, different possible configurations for the power train in EV/HEV can be found in the automotive market [25]–[28].”
BackgroundVernica, I., Wang, H., & Blaabjerg, F. (2020) · IEEE International Symposium on Power Semiconductor Devices and ICs/Proceedings of the International Symposium on Power Semiconductor Devices & ICs/Proceedings of the ... International Symposium on Power Semiconductor Devices & ICs/Proceedings of the ... International Symposium on Power Semiconductor Devices and ICs · doi:10.1109/ispsd46842.2020.9170201 · Cited by 18
Self-citationVernica, I., Wang, H., & Blaabjerg, F. (2018) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2018.8558092 · Cited by 17
Self-citationReliable power electronics for automotive applications
Seliger, N., Wolfgang, E., Lefranc, G., et al. (2002) · Microelectronics Reliability · doi:10.1016/s0026-2714(02)00197-x · Cited by 16 · cited 1×
“temperature of cooling liquid in 90 ◦C–125 ◦C [57].”
(2019) · NASA Technical Reports Server (NASA) · Cited by 16
Integrated Liquid Cooling Automotive IGBT Module for High Temperatures Coolant Application
Wang, Y., Dai, X., Liu, G., Wu, Y., Li, D., & Jones, S. (2015) · PCIM Europe: International Exhibition and Conference for Power Electronics, Intelligent Motion, Renewable Energy and Energy Management (PCIM Europe) · Cited by 14
(2014) · Cited by 13
Status and Trend of Power Semiconductor Module Packaging for Electric Vehicles
Wang, Y., Dai, X., Liu, G., Wu, Y., Li, Y., & Jones, S. (2016) · InTech eBooks · doi:10.5772/64173 · Cited by 12 · cited 2×
“8(b) is used to calculate the capacitor’s electrical and thermal loading [77], [86].”
BackgroundMethodVernica, I., Choi, U., Wang, H., & Blaabjerg, F. (2020) · Microelectronics Reliability · doi:10.1016/j.microrel.2020.113800 · Cited by 12
Self-citationLoss and thermal model for power semiconductors including device rating information
Ma, K., Bahman, A. S., Bęczkowski, S., & Blaabjerg, F. (2014) · International Power Electronics Conference (IPEC) · doi:10.1109/ipec.2014.6870087 · Cited by 11
Self-citationLoad-Dependent Active Thermal Control of Grid-Forming Converters
Andresen, M., De Carne, G., & Liserre, M. (2020) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2020.2966573 · Cited by 10
Power module platform for automotive reliability requirements
Pavliček, N., Liu, C., Loisy, J.-Y., Salvatore, G. A., Mohn, F., Schuderer, J., Apelsmeier, A., Dresel, F., Schletz, A., & Vater, S. (2019) · European Conference on Power Electronics and Applications · doi:10.23919/epe.2019.8915223 · Cited by 9 · cited 1×
“The main causes of temperature cycles are active power cycling and passive temperature cycling [50], [51].”
BackgroundUncertainties in the Lifetime Prediction of IGBTs for a Motor Drive Application
Vernica, I., Wang, H., & Blaabjerg, F. (2018) · IEEE International Power Electronics and Application Conference and Exposition (PEAC) · doi:10.1109/peac.2018.8590417 · Cited by 7 · cited 1×
“As shown in [99]–[101], certain degrees of uncertainty can be introduced by various factors, such as environmental mission profiles, electrothermal modeling, and lifetime models.”
BackgroundSelf-citationDevelopment, testing, and application of metallic TIMs for harsh environments and non-flat surfaces
Saums, D. L., & Jensen, T. (2017) · 2017 16th IEEE Intersociety Conference on Thermal and Thermomechanical Phenomena in Electronic Systems (ITherm) · doi:10.1109/itherm.2017.7992642 · Cited by 6 · cited 1×
“To cope with the challenges above, currently, there are three research directions to protect the power electronic components from being overheated, that is, improving the power package design, as discussed in Section III-A, developing advanced thermal interface material [78] and utilizing more powerful cooling techniq…”
BackgroundVerdingovas, V. (2015) · Cited by 6
Defossilizing the Transportation Sector
Krämer, U. (2019) · Springer eBooks · doi:10.1007/978-3-662-58006-6_23 · Cited by 5
Frequency-domain thermal modelling of power semiconductor devices
Ma, K., He, N., Blaabjerg, F., Andresen, M., & Liserre, M. (2015) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2015.7309960 · Cited by 5
Self-citation
Research works printed but not linked: 21
- 2018, The Roadmap Report Towards 2040 A Guide to Automotive Propulsion Technologies
- 2018, Shaping Future Electromobility With Semiconductor Innovations
- 2015, Handbook for Robustness Validation of Semiconductor Devices in Automotive Applications
- ehsani, 2018, Modern Electric Hybrid Electric and Fuel Cell Vehicles
- drexhage, 2016, Effect of humidity and condensation on power electronics systems
- 2013, Electric and Electronic Components in Motor Vehicles up to 3 5t
- 2020, Electric vehicle outlook 2020
- 2013, Failure Mechanism Based Stress Test Qualification for Discrete Semiconductors in Automotive Applications REV D1
- 2017, Electrical and electronics technical team roadmap
- 2008, Vorlesung Qualtat und Zuverlassigkeit von Fahrzeug e/e Hardware an der tu Berlin
- 2010, Stress Test Qualification for Passive Components
- 2013, Zvei Die Elektroindustrie Handbook for Robustness Validation of Automotive Electrical/Electronic Modules
- allouche, 2020, Hitachi DSC Power Module From Audi e-Tron Inverter
- christmann, 2009, Reliability of power modules in hybrid vehicles, Proc PCIM Eur, 359
- 2019, Qualification of Power Modules for Use in Power Electron Converter Units in Motor Vehicles
- ishihara, 2012, New transfer-mold power module series for automotive power-train inverters, Proc PCIM Eur, 1408
- ishihara, 2014, New compact-package power modules for electric and hybrid vehicles (J1 series), Proc PCIM Eur, 1093
- kimura, 2014, High-power-density inverter technology for hybrid and electric vehicle applications, Hitachi Rev, 63, 41
- knappik, 2019, The advantages of 48-volt vehicle electronics, Veh Technol
- 2005, Standard Practices for Cycle Counting in Fatigue Analysis
- wintrich, 2015, Application Manual Power Semiconductors
Cited by
Research Development on Aqueous Ammonium‐Ion Batteries
Zhang, R., Wang, S., Chou, S., & Jin, H. (2022) · Advanced Functional Materials · doi:10.1002/adfm.202112179 · Cited by 172
Ullah, Z., Wang, S., Wu, G., Hasanien, H. M., Rehman, A. U., Turky, R. A., & Elkadeem, M. R. (2022) · Energy · doi:10.1016/j.energy.2022.126560 · Cited by 157
Ten questions concerning active noise control in the built environment
Lam, B., Gan, W., Shi, D., Nishimura, M., & Elliott, S. J. (2021) · Building and Environment · doi:10.1016/j.buildenv.2021.107928 · Cited by 150
“Increased electrification of automobiles have also improved the longevity of automotive electronics to meet the expected operating life of more than ten years [160], providing a reliable infrastructure for digital ANC applications [18,156].”
BackgroundRahman, S. M. I., Moghassemi, A., Arsalan, A., Timilsina, L., Chamarthi, P. K., Papari, B., Özkan, G., & Edrington, C. S. (2024) · IEEE Access · doi:10.1109/access.2024.3385429 · Cited by 167
“The high voltage high-power PECs used in EVs face a harsh environment due to the strict operating conditions [268].”
BackgroundArtificial-Intelligence-Based Design for Circuit Parameters of Power Converters
Li, X., Zhang, X., Lin, F., & Blaabjerg, F. (2021) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2021.3088377 · Cited by 129
“And efficiency, size, cost, reliability, ripples, and transient response are several commonlyadopted design objectives [7]–[10].”
BackgroundSelf-citation
Metadata
- Authors
- Blaabjerg, F., Wang, H., Vernica, I., Liu, B., & Davari, P.
- Affiliations
- Aalborg University (DK)
- Venue
- Proceedings of the IEEE
- Published
- 2021-06
- Volume
- 109
- Issue
- 6
- Pages
- 1060-1076
- ISSN
- 0018-9219 (ISSN-L)
- 1558-2256
- OpenAlex
- W3095570029
- Cited by
- 249
- References
- 88
- Citations by year
- 2026: 35 · 2025: 57 · 2024: 67 · 2023: 52 · 2022: 23 · 2021: 15
- FWCI
- 7.72
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Locations
- Proceedings of the IEEE (publishedVersion, cc-by)
- VBN Forskningsportal (Aalborg Universitet) (publishedVersion, cc-by)
- Funders
- VILLUM FONDEN under the VILLUM Investigators (00016591)
- Innovation Fund Denmark through the Advanced Power Electronic Technology and Tools Project
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Silicon Carbide Semiconductor Technologies
- Physical Sciences › Engineering › Automotive Engineering › Electric and Hybrid Vehicle Technologies
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Electric Power Systems and Control
- Keywords
- power electronics reliability, electric vehicles, hybrid electric vehicles, reliability requirements, power electronic components, reliability-oriented design, on-board charger, inverter, vehicle electrification
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.