Location Fingerprinting With Bluetooth Low Energy Beacons
The DOI matches its Crossref record; 21 of the 21 references it cites were found in a registry or an index.
Abstract
The complexity of indoor radio propagation has resulted in location-awareness being derived from empirical fingerprinting techniques, where positioning is performed via a previously-constructed radio map, usually of WiFi signals. The recent introduction of the Bluetooth Low Energy (BLE) radio protocol provides new opportunities for indoor location. It supports portable battery-powered beacons that can be easily distributed at low cost, giving it distinct advantages over WiFi. However, its differing use of the radio band brings new challenges too. In this work, we provide a detailed study of BLE fingerprinting using 19 beacons distributed around a ~600 m2testbed to position a consumer device. We demonstrate the high susceptibility of BLE to fast fading, show how to mitigate this, and quantify the true power cost of continuous BLE scanning. We further investigate the choice of key parameters in a BLE positioning system, including beacon density, transmit power, and transmit frequency. We also provide quantitative comparison with WiFi fingerprinting. Our results show advantages to the use of BLE beacons for positioning. For one-shot (push-to-fix) positioning we achieve2), compared to2) and <; 8.5 m for an established WiFi network in the same area.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“Because the Wi-Fi APs and BLE beacons share the same frequency range (2.4 GHz) there may be interference problems [15], although: (1) interference problems usually occur when the number of access points is very large, something that did not happen in our case; (2) possible interference problems could be overcome by avoiding certain channels and taking into account the fact that Bluetooth”
From Study on an Indoor Positioning System for Harsh Environments Based on Wi-Fi and Bluetooth Low Energy (2017) · cites this paper as [15]
In the citing paper
“this is simply the consequence of the fact that BLE technology transmits advertisements on these channels to mitigate interference with other devices [15].”
From Study on an Indoor Positioning System for Harsh Environments Based on Wi-Fi and Bluetooth Low Energy (2017) · cites this paper as [15]
Citations
Cites
Survey of Wireless Indoor Positioning Techniques and Systems
Liu, H., Darabi, H., Banerjee, P., & Liu, J. (2007) · IEEE Transactions on Systems, Man and Cybernetics, Part C (Applications and Reviews) · doi:10.1109/tsmcc.2007.905750 · Cited by 4,098 · cited 1×
“Indoor positioning is a mature research field, with many proposed technologies and techniques—comprehensive overviews can be found in [19], [18], [2].”
BackgroundThe Horus WLAN location determination system
Youssef, M., & Agrawala, A. (2005) · Proceedings of the 3rd international conference on Mobile systems, applications, and services · doi:10.1145/1067170.1067193 · Cited by 1,653 · cited 1×
“Here the focus is on radio positioning, specifically using the empirical fingerprinting techniques [3], [15], [17], [22] that avoid the need to model the complex radio propagation environment indoors by patternmatching to a previously surveyed map of radio signal strengths.”
BackgroundA Survey of Indoor Inertial Positioning Systems for Pedestrians
Harle, R. (2013) · IEEE Communications Surveys & Tutorials · doi:10.1109/surv.2012.121912.00075 · Cited by 814 · cited 1×
“fingerprints with other sources to form hybrid systems, many of which are based on the idea of Simultaneous Localization and Mapping (SLAM) [10], [16] being applied to pedestrian dead reckoning [13].”
BackgroundSelf-citationWiFi-SLAM Using G aussian Process Latent Variable Models
Ferris, B., Fox, D., & Lawrence, N. D. (2007) · International Joint Conference on Artificial Intelligence · Cited by 610
Network Time Protocol Version 4: Protocol and Algorithms Specification
Mills, D., Burbank, J., & Kasch, W. (2010) · doi:10.17487/rfc5905 · Cited by 577
A comparative survey of WLAN location fingerprinting methods
Honkavirta, V., Perala, T., Ali-Loytty, S., & Piche, R. (2009) · 2009 6th Workshop on Positioning, Navigation and Communication · doi:10.1109/wpnc.2009.4907834 · Cited by 522
Enhancements to the RADAR User Location and Tracking System
Bahl, V., & Padmanabhan, V. (2000) · Cited by 507
Implementing a sentient computing system
Addlesee, M., Curwen, R., Hodges, S., Newman, J., Steggles, P., Ward, A., & Hopper, A. (2001) · Computer · doi:10.1109/2.940013 · Cited by 490 · cited 1×
“Ground Truth Location: The Active Bat system [1] was available throughout the testbed and was used to provide ground truth position.”
MethodA Survey of Indoor Positioning and Object Locating Systems
Koyuncu, H., & Yang, S. H. (2010) · Cited by 251
COMPASS: A probabilistic indoor positioning system based on 802.11 and digital compasses
King, T., Kopf, S., Haenselmann, T., Lubberger, C., & Effelsberg, W. (2006) · Proceedings of the 1st international workshop on Wireless network testbeds, experimental evaluation & characterization · doi:10.1145/1160987.1160995 · Cited by 223
Research works printed but not linked: 2
- ferris, 0, WiFi-SLAM using Gaussian process latent variable models, Proc 20th IJCAI, 2480
- 2010, Bluetooth Specification Version 4 0
Cited by
Items 101–200 of 917
A proximity-based indoor navigation system tackling the COVID-19 social distancing measures
Fazio, M. C., Buzachis, A., Galletta, A., Celesti, A., & Villari, M. (2020) · IEEE Symposium on Computers and Communications (ISCC) · doi:10.1109/iscc50000.2020.9219634 · Cited by 51
“Faragher and Harle [5] implemented this method with Bluetooth beacons.”
MethodAn Outline of Multi-Sensor Fusion Methods for Mobile Agents Indoor Navigation
Qu, Y., Yang, M., Zhang, J., Xie, W., Qiang, B., & Chen, J. (2021) · Sensors · doi:10.3390/s21051605 · Cited by 57
“Ranging algorithm: TOF [39], AOA [40], TOA [40] and TDOA [37] Indoors High location accuracy Insufficient flexibility in applications Wi-Fi, Bluetooth, ZigBee, infrared, ultrasonic, etc. Distance measurement method which is similar to UWB system [6–10] Mainly indoors”
BackgroundSmart Leaky‐Wave Antennas for Iridescent IoT Wireless Networks
Gómez‐Tornero, J. L. (2022) · Wiley eBooks · doi:10.1002/9781119813910.ch4 · Cited by 66
Experience: pushing indoor localization from laboratory to the wild
Ni, J., Zhang, F., Xiong, J., Huang, Q., Chang, Z., Ma, J., Xie, B., Wang, P., Bian, G., Li, X., et al. (2022) · ACM Annual International Conference on Mobile Computing and Networking (MobiCom) · doi:10.1145/3495243.3560546 · Cited by 50
“Different wireless technologies have been exploited for indoor localization including WiFi [8, 9, 20, 36, 51, 59, 60], Bluetooth [16, 23, 28, 34, 55] and UWB [10, 45, 63].”
Indoor Positioning System using Bluetooth Low Energy
Kalbandhe, A. A., & Patil, S. C. (2016) · International Conference on Computing, Analytics and Security Trends · doi:10.1109/cast.2016.7915011 · Cited by 50
Castillo‐Cara, M., Lovón-Melgarejo, J., Bravo-Rocca, G., Orozco–Barbosa, L., & García-Varea, I. (2017) · Sensors · doi:10.3390/s17061318 · Cited by 55
“As in previous related works [10,15], we explore the use of two supervised learning algorithms: The k-Nearest Neighbour (k-NN) and the Support Vector Machine (SVM) algorithms [11].”
MethodFirmXRay: Detecting Bluetooth Link Layer Vulnerabilities From Bare-Metal Firmware
Wen, H., Lin, Z., & Zhang, Y. (2020) · ACM SIGSAC Conference on Computer and Communications Security (CCS) · doi:10.1145/3372297.3423344 · Cited by 72
“Recently, there were also identity tracking attacks that leverage the static MAC address [27], signal strength [29], and advertised information [37], and static UUIDs [63] [20].”
BackgroundOutdoor Fingerprinting Localization Using Sigfox
Janssen, T., Aernouts, M., Berkvens, R., & Weyn, M. (2018) · International Conference on Indoor Positioning and Indoor Navigation · doi:10.1109/ipin.2018.8533826 · Cited by 51
“Up to now, fingerprinting is mostly used in constricted indoor environments with wireless technologies such as Wi-Fi, Bluetooth Low Energy (BLE), etc [9], [10].”
BackgroundHigh-Accuracy Localization and Calibration for 5-DoF Indoor Magnetic Positioning Systems
Hehn, M., Sippel, E., Carlowitz, C., & Vossiek, M. (2018) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2018.2884040 · Cited by 49
“Examples for RF positioning systems are narrowband RF systems that used WLAN [7], Zigbee [8], and Bluetooth [9], ultra-wideband systems (UWB) such as pulse radar [10], cellular-based systems [11], and radio-frequency identification (RFID [12].”
MethodAn IoT-based Emergency Evacuation System
Zualkernan, I. A., Aloul, F., Sakkia, V., Noman, H. A., Sowdagar, S., & Hammadi, O. A. (2019) · IEEE International Conference on Internet of Things and Intelligence Systems (IoTaIS) · doi:10.1109/iotais47347.2019.8980381 · Cited by 49
An IOT based smart grid system for advanced cooperative transmission and communication
Alomar, M. A. (2023) · Physical Communication · doi:10.1016/j.phycom.2023.102069 · Cited by 49
LoRaIn: Making a Case for LoRa in Indoor Localization
Islam, B., Islam, M. T., Kaur, J., & Nirjon, S. (2019) · IEEE International Conference on Pervasive Computing and Communications Workshops (PerCom Workshops) · doi:10.1109/percomw.2019.8730767 · Cited by 48
“The problem of indoor localization has been extensively studied for wireless protocols such as BLE [6] and WiFi [8].”
BackgroundMethodStudy on Accuracy of Trilateration Method for Indoor Positioning with BLE Beacons
Pakanon, N., Chamchoy, M., & Supanakoon, P. (2020) · International Conference on Engineering, Applied Sciences, and Technology (ICEAST) · doi:10.1109/iceast50382.2020.9165464 · Cited by 48
“For example, positioning that uses path loss models [2], weighted centroid approach [3] and fingerprinting techniques [4]-[5].”
MethodHailu, T. G., Guo, X., Si, H., Li, L., & Zhang, Y. (2024) · Sensors · doi:10.3390/s24216876 · Cited by 53
“BLE fingerprinting technology has also been investigated for target detection at various beacon densities [111].”
BackgroundluXbeacon—A Batteryless Beacon for Green IoT: Design, Modeling, and Field Tests
Jeon, K. E., She, J. P. M., Xue, J., Kim, S., & Park, S. (2019) · IEEE Internet of Things Journal · doi:10.1109/jiot.2019.2894798 · Cited by 47
“as museums [14], homes [15], and offices [16], [17], wireless sensor nodes are mainly deployed in outdoor places for data collecting purposes [18], [19].”
BackgroundAccuracy Investigation of the Pose Determination of a VR System
Bauer, P., Lienhart, W., & Jost, S. (2021) · Sensors · doi:10.3390/s21051622 · Cited by 47
“fingerprinting [15], High sensitivity GNSS [16], the iGPS system from Metris [12], or the CLIPS system of ETH Zurich [17].”
MethodA review of smartphones‐based indoor positioning: Challenges and applications
Nguyen, K. A., Luo, Z., Li, G., & Watkins, C. (2021) · IET Cyber-Systems and Robotics · doi:10.1049/csy2.12004 · Cited by 46
Technological Viability Assessment of Bluetooth Low Energy Technology for Indoor Localization
Topak, F., Pekeriçli, M. K., & Tanyer, A. M. (2018) · Journal of Computing in Civil Engineering · doi:10.1061/(asce)cp.1943-5487.0000778 · Cited by 46
Hepp, T., Wortner, P., Schönhals, A., & Gipp, B. (2018) · Workshop on Cryptocurrencies and Blockchains for Distributed Systems (CryBlock) · doi:10.1145/3211933.3211944 · Cited by 54
“One possibility is working with active or passive RFIDs [21] or BLE [6].”
BackgroundReal-time visible light positioning supporting fast moving speed
Lin, P., Hu, X., Ruan, Y., Li, H., Fang, J., Zhong, Y., Zheng, H., Fang, J., Jiang, Z. L., & Chen, Z. (2020) · Optics Express · doi:10.1364/oe.390781 · Cited by 45
Design and Demonstration of Robust Visible Light Positioning Based on Received Signal Strength
Huang, N., Gong, C., Luo, J., & Xu, Z. (2020) · Journal of Lightwave Technology · doi:10.1109/jlt.2020.3001761 · Cited by 47
“In order to realize indoor positioning, many approaches have been explored by utilizing indoor wireless signals such as WiFi [6], Bluetooth [7], and radio frequency identification (RFID) [8].”
BackgroundRandom Forest Learning Based Indoor Localization as an IoT Service for Smart Buildings
Varma, P. S., & Anand, V. (2020) · Wireless Personal Communications · doi:10.1007/s11277-020-07977-w · Cited by 47
DoA-LF: A Location Fingerprint Positioning Algorithm With Millimeter-Wave
Wei, Z., Zhao, Y., Liu, X., & Feng, Z. (2017) · IEEE Access · doi:10.1109/access.2017.2753781 · Cited by 49
“bluetooth low energy (BLE) subsystem, which is ‘‘designed for machine type communication’’ [3], BLE devices will be more and more dense in buildings.”
BackgroundIndoor Positioning for Monitoring Older Adults at Home: Wi-Fi and BLE Technologies in Real Scenarios
Montoliu, R., Sansano‐Sansano, E., Gascó, A., Belmonte, Ó., & Miedes, A. C. (2020) · Electronics · doi:10.3390/electronics9050728 · Cited by 49
“Similarly, in [12,13], the authors tested the system in an office scenario of 50 m × 15 m and 52 m × 34 m, respectively.”
MethodSmartphone-Based Indoor Positioning Technologies
Chen, R., & Chen, L. (2021) · The urban book series · doi:10.1007/978-981-15-8983-6_26 · Cited by 50
Occupancy detection by multi-power bluetooth low energy beaconing
Barsocchi, P., Crivello, A., Girolami, M., Mavilia, F., & Palumbo, F. (2017) · International Conference on Indoor Positioning and Indoor Navigation · doi:10.1109/ipin.2017.8115946 · Cited by 44
“Differently, with a low power transmission we can achieve good performance in proximity-based scenarios [16], while with a high transmission power it is possible to provide more fine-grained results [17].”
BackgroundParticle Filtering-Based Indoor Positioning System for Beacon Tag Tracking
Shen, Y. C., Hwang, B., & Jeong, J. P. (2020) · IEEE Access · doi:10.1109/access.2020.3045610 · Cited by 44
“Using fingerprinting of RSSI signals [11] can be another available approach but requires a site survey and a labor-intensive fingerprint collection process.”
MethodSteendam, H., Wang, T. Q., & Armstrong, J. (2016) · International Conference on Communications · doi:10.1109/icc.2016.7510822 · Cited by 42
High Resolution Beacon-Based Proximity Detection for Dense Deployment
Ng, P. C., She, J. P. M., & Park, S. (2017) · IEEE Transactions on Mobile Computing · doi:10.1109/tmc.2017.2759734 · Cited by 42
“An LBS is a locationrestricted service delivered according to the location information [6], [7], [8], which can be estimated via the received signal strength (RSS)-based localization techniques, such as trilateration [9], [10] and fingerprinting [11], [12], [13].”
MethodEnergy efficiency and accuracy of solar powered BLE beacons
Spachos, P., & Mackey, A. (2017) · Computer Communications · doi:10.1016/j.comcom.2017.12.007 · Cited by 42
“BLE Beacons are a popular solution for indoor location [21, 22, 23], tracking [24].”
BackgroundUnsupervised Crowd-Assisted Learning Enabling Location-Aware Facilities
Sikeridis, D., Rimal, B. P., Papapanagiotou, I., & Devetsikiotis, M. (2018) · IEEE Internet of Things Journal · doi:10.1109/jiot.2018.2810808 · Cited by 42
“Therefore, indoor localization applications were among the first to explore the capabilities of BLE in this domain with approaches that span from fingerprint-based systems [6] to infrastructure implementations for museums [1] or marketing and advertisement [29].”
BackgroundUnsupervised Indoor Localization Based on Smartphone Sensors, iBeacon and Wi-Fi
Chen, J., Zhang, Y., & Xue, W. (2018) · Sensors · doi:10.3390/s18051378 · Cited by 42
“Some research and papers [5,13-16] use landmarks to correct user’s location, but these landmarks can not ensure whether user is in landmarks, they can only guess that user is close to the landmarks.”
BackgroundReal-Time Indoor Positioning Approach Using iBeacons and Smartphone Sensors
Liu, L., Li, B., Yang, L., & Liu, T. (2020) · Applied Sciences · doi:10.3390/app10062003 · Cited by 42
“In another related study [11], the researchers set a window for batch filtering, and get the best performance (around 2.”
BackgroundMethodInfluentialDoppler Shift Mitigation in Acoustic Positioning Based on Pedestrian Dead Reckoning for Smartphone
Liu, T., Niu, X., Kuang, J., Cao, S., Zhang, L., & Chen, X. '. (2020) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2020.3010384 · Cited by 45
“Fingerprint matching based on the received signal strength is the most common localization methodology of WiFi and Bluetooth positioning [5], [12].”
BackgroundWang, Y., Yang, Q., Zhang, G., & Zhang, P. (2016) · doi:10.1109/iota.2016.7562730 · Cited by 41
“For iPhones, the hardware version should be no lower than iPhone 4s, and OS version should be no lower than iOS 7.”
BackgroundINTRI: Contour-Based Trilateration for Indoor Fingerprint-Based Localization
He, S., & Chan, S.-H. G. (2016) · IEEE Transactions on Mobile Computing · doi:10.1109/tmc.2016.2604810 · Cited by 40
Enabling and Emerging Technologies for Social Distancing: A Comprehensive Survey
Ct, N., Ym, S., Nv, H., Nguyen, N.-T., Tv, K., Bm, T., Nguyen, D., Dt, H., Vu, T. X., Dutkiewicz, E., et al. (2020) · Europe PMC (PubMed Central) · Cited by 45
Achieving Democracy in Edge Intelligence: A Fog-Based Collaborative Learning Scheme
Zhang, T., Shen, Z., Jin, J., Zheng, X., Tagami, A., & Cao, X. (2020) · IEEE Internet of Things Journal · doi:10.1109/jiot.2020.3020911 · Cited by 41
“Therefore, we focus on using the more accessible RSSI signal data from reference wireless signal transmission devices (namely “fingerprinting” [26]) to benefit the trajectory prediction, and the work in this paper is the first of its kind”
MethodTalla-Chumpitaz, R., Castillo‐Cara, M., Orozco–Barbosa, L., & García‐Castro, R. (2022) · Information Fusion · doi:10.1016/j.inffus.2022.10.011 · Cited by 39
Accuracy Study of Indoor Positioning with Bluetooth Low Energy Beacons
Phutcharoen, K., Chamchoy, M., & Supanakoon, P. (2020) · Joint International Conference on Digital Arts, Media and Technology with ECTI Northern Section Conference on Electrical, Electronics, Computer and Telecommunications Engineering (ECTI DAMT & NCON) · doi:10.1109/ectidamtncon48261.2020.9090691 · Cited by 39
“For example, positioning using the path loss model [3], weighted centroid [4], and fingerprinting technique [5]-[6].”
MethodA Novel Fingerprint Positioning Method Applying Vision-Based Definition for WIFI-Based Localization
Tang, C., Sun, W., Zhang, X., Zheng, J. Q., Wu, W., & Sun, J. (2023) · IEEE Sensors Journal · doi:10.1109/jsen.2023.3280903 · Cited by 41
“tunnels), it is impossible to achieve indoor localization [1].”
BackgroundA BLE-based probabilistic room-level localization method
Kyritsis, A. I., Kostopoulos, P., Deriaz, M., & Konstantas, D. (2016) · International Conference on Localization and GNSS · doi:10.1109/icl-gnss.2016.7533848 · Cited by 38
“Either deriving a location from fingerprinting techniques [14], or ranging techniques that use path-loss models [3], researchers have focused on increasing the accuracy of the positioning.”
MethodAssessing the impact of multi-channel BLE beacons on fingerprint-based positioning
Powar, J., Gao, C., & Harle, R. K. (2017) · International Conference on Indoor Positioning and Indoor Navigation · doi:10.1109/ipin.2017.8115871 · Cited by 38
“The multi-channel scheme identification in [7] involved using three beacons stacked on top of each other, with the composite signal formed by simply concatenating the three channels.”
BackgroundSelf-citationBLEach: Exploiting the Full Potential of IPv6 over BLE in Constrained Embedded IoT Devices
Spörk, M., Boano, C. A., Zimmerling, M., & Römer, K. (2017) · ACM Conference on Embedded Networked Sensor Systems (SenSys) · doi:10.1145/3131672.3131687 · Cited by 38
A Comparison of Signal Strength Localization Methods with Sigfox
Aernouts, M., Bellekens, B., Berkvens, R., & Weyn, M. (2018) · Workshop on Positioning, Navigation and Communications (WPNC) · doi:10.1109/wpnc.2018.8555743 · Cited by 40
“Because it is easier to create such a database in small, indoor environments, fingerprinting localization has mainly been implemented in indoor environments with widely used wireless technologies such as Wi-Fi and Bluetooth [10], [11].”
BackgroundVisible Light Localization Using Conventional Light Fixtures and Smartphones
Zhang, C., & Zhang, X. (2018) · IEEE Transactions on Mobile Computing · doi:10.1109/tmc.2018.2888973 · Cited by 38
“Prior research has explored fingerprinting [4], [5], [6], propagationmodeling [7], and triangulation [8], [9].”
Zheng, L., Hu, B., Qiu, J., & Cui, M. (2020) · IEEE Internet of Things Journal · doi:10.1109/jiot.2020.2981723 · Cited by 40
“Nevertheless, some common indoor localization methods based on wireless fidelity (Wi-Fi) [1]–[5], Bluetooth [6], [7], infrared [8], visible light [9], radio-”
BackgroundInk‐Based Additive Nanomanufacturing of Functional Materials for Human‐Integrated Smart Wearables
Xu, S., & Wu, W. (2020) · Advanced Intelligent Systems · doi:10.1002/aisy.202000117 · Cited by 36
A Survey of Automatic Contact Tracing Approaches Using Bluetooth Low Energy
Reichert, L., Brack, S., & Scheuermann, B. (2021) · ACM Transactions on Computing for Healthcare · doi:10.1145/3444847 · Cited by 47
On the accuracy of BLE indoor localization systems: An assessment survey
Morgan, A. A. (2024) · Computers & Electrical Engineering · doi:10.1016/j.compeleceng.2024.109455 · Cited by 37
Maxlifd: Joint Maximum Likelihood Localization Fusing Fingerprints and Mutual Distances
He, S., Chan, S.-H. G., Yu, L., & Liu, N. (2018) · IEEE Transactions on Mobile Computing · doi:10.1109/tmc.2018.2841842 · Cited by 38
Indoor Localization for Evacuation Management in Emergency Scenarios
Depari, A., Flammini, A., Fogli, D., & Magrino, P. (2018) · IEEE International Workshop on Metrology for Industry 4.0 & IoT (MetroInd4.0&IoT) · doi:10.1109/metroi4.2018.8428343 · Cited by 37
“Bluetooth Low Energy (BLE) radio protocols (beacons in the following) provide new ways for indoor localization [16].”
BackgroundResultA Compressive Sensing Approach to Detect the Proximity Between Smartphones and BLE Beacons
Ng, P. C., She, J. P. M., & Ran, R. (2019) · IEEE Internet of Things Journal · doi:10.1109/jiot.2019.2914733 · Cited by 37
A Comparison Analysis of BLE-Based Algorithms for Localization in Industrial Environments
Cannizzaro, D., Zafiri, M., Pagliari, D. J., Patti, E., Macii, E., Poncino, M., & Acquaviva, A. (2019) · Electronics · doi:10.3390/electronics9010044 · Cited by 37
“According to literature [27], there are many factors affecting the accuracy of BLE-based localization.”
BackgroundA Blockchain Approach for Decentralized V2X (D-V2X)
Agudo, I., Montenegro-Gómez, M., & López, J. (2020) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2020.3046640 · Cited by 42
“Bluetooth Low Energy is expanding Bluetooth usage scenarios, from location-based services [15] to IoT [16].”
BackgroundLuo, H., Li, Y., Wang, J., Weng, D., Ye, J., Hsu, L., & Chen, W. (2021) · IEEE Access · doi:10.1109/access.2021.3052733 · Cited by 37
Privacy-preserving COVID-19 contact tracing using blockchain
Tahir, S., Tahir, H., Sajjad, A., Rajarajan, M., & Khan, F. A. (2021) · Journal of Communications and Networks · doi:10.23919/jcn.2021.000031 · Cited by 38
Constrained Localization: A Survey
Savić, T., Vilajosana, X., & Watteyne, T. (2022) · IEEE Access · doi:10.1109/access.2022.3171859 · Cited by 41
“[85] inside/out RSS/Fingerprint Bluetooth no > 10 cm > 10 Hz < 1 year < USD 20”
MethodFischer, G., Schaechtle, T., Gabbrielli, A., Bordoy, J., Häring, I., Höflinger, F., & Rupitsch, S. J. (2025) · IEEE Communications Surveys & Tutorials · doi:10.1109/comst.2025.3567765 · Cited by 47
“It has been widely adopted in indoor localization, where several systems utilize the technology through methods such as RSSI fingerprinting by deploying multiple repeatedly emitting beacons around a certain area [1], [32], [199].”
Risk estimation of SARS-CoV-2 transmission from bluetooth low energy measurements
Sattler, F., Ma, J., Wagner, P., Neumann, D., Wenzel, M. A., Schäfer, R., Samek, W., Müller, K., & Wiegand, T. (2020) · npj Digital Medicine · doi:10.1038/s41746-020-00340-0 · Cited by 36
Room-Level Localization System Based on LoRa Backscatters
Lázaro, A., Lázaro, M., & Villarino, R. (2021) · IEEE Access · doi:10.1109/access.2021.3053144 · Cited by 42
“The RSSI measurement provided by BLE devices can be used for localization [63].”
MethodEmpirical analysis and modeling of Bluetooth low-energy (BLE) advertisement channels
Nikoukar, A., Abboud, M., Samadi, B., Güneş, M., & Dezfouli, B. (2018) · Annual Mediterranean Ad Hoc Networking Workshop · doi:10.23919/medhocnet.2018.8407089 · Cited by 36
“Another study [23] analyzed the RSS variation of ADV_CHs individually in one environment where the distance between the nodes is fixed.”
Constrained Least-Squares Trilateration for Indoor Positioning System Under High GDOP Condition
Bach, S.-H., & Yi, S.-Y. (2023) · IEEE Transactions on Industrial Informatics · doi:10.1109/tii.2023.3326535 · Cited by 35
“1109/TII.2023.3326535 The IPS has been implemented using various technologies, including ultrasonics [6], Bluetooth [7], radio frequency identi-fication [8], and ultrawideband (UWB) [1].”
MethodInfluentialChandel, V., Ahmed, N., Arora, S., & Ghose, A. (2016) · International Conference on Indoor Positioning and Indoor Navigation · doi:10.1109/ipin.2016.7743592 · Cited by 40
“[20] which provides a detailed study in BLE based fingerprinting, es-”
BackgroundPRISER: Managing Notification in Multiples Devices with Data Privacy Support
Silva, L. A., Leithardt, V. R. Q., Rolim, C. O., González, G. V., Geyer, C. F. R., & Silva, J. S. (2019) · Sensors · doi:10.3390/s19143098 · Cited by 37
An Ensemble Filter for Indoor Positioning in a Retail Store Using Bluetooth Low Energy Beacons
Stavrou, V., Bardaki, C., Papakyriakopoulos, D., & Pramatari, K. C. (2019) · Sensors · doi:10.3390/s19204550 · Cited by 38
Confidence-Interval-Fuzzy-Model-Based Indoor Localization
Tomažič, S., Dovžan, D., & Škrjanc, I. (2018) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2018.2840525 · Cited by 34
“The Bluetooth network (based on Bluetooth low energy (BLE) [23]) has many advantages over Wi-Fi [2], [24]: the lower energy consumption of the receivers (smart-phones) and transmitters (a button-cell battery can supply trans-mitters for several months or even years), the low price of the…”
BackgroundA GPS-Based Indoor Positioning System With Delayed Repeaters
Li, X. (2018) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2018.2889928 · Cited by 34
“Various solutions have been proposed and applied, such as WLAN(Wireless Local Area Network)-based [1]–[3], RFID(Radio Frequency Identification)-based [4]–[8], UWB(Ultra-WideBand)-based [9]–[11] and Bluetooth-based [12]–[14] systems.”
MethodGriffiths, S., Wong, M. S., Kwok, C. Y. T., Kam, R., Lam, S. C., Yang, L., Yip, T. L., Heo, J. Y., Chan, B. S. B., Xiong, G., et al. (2019) · Sustainability · doi:10.3390/su11154005 · Cited by 34
“When several beacon signals are received by the device, the user’s location can be determined via trilateration [13,14] or the fingerprinting method [15].”
MethodDecentralized adaptive indoor positioning protocol using Bluetooth Low Energy
Ho, Y. H., & Chan, H. C. B. (2020) · Computer Communications · doi:10.1016/j.comcom.2020.04.041 · Cited by 36
A Perspective on Passive Human Sensing with Bluetooth
Iannizzotto, G., Milici, M., Nucita, A., & Bello, L. L. (2022) · Sensors · doi:10.3390/s22093523 · Cited by 38
Machine Learning-Powered Radio Frequency Sensing: A Review
Santra, A., Wang, P. P., Shaker, G. S. A., R., B. S. M., Dolmans, G., Chen, Y., Shariati, N., & Pandharipande, A. (2025) · IEEE Sensors Journal · doi:10.1109/jsen.2025.3547673 · Cited by 40
“Similar to Wi-Fi, traditional approaches rely on BLE RSSI using either signal processing techniques or ML approaches to map it to distance or ToF estimates [108], [109], [110], [111].”
An Optimal Enhanced Kalman Filter for a ZUPT-Aided Pedestrian Positioning Coupling Model
Fan, Q., Zhang, H., Sun, Y., Zhu, Y., Zhuang, X., Jia, J., & Zhang, P. (2018) · Sensors · doi:10.3390/s18051404 · Cited by 34
“Faragher, R.; Harle, R. Location fingerprinting with Bluetooth low energy beacons.”
BackgroundIntegrity Monitoring for Bluetooth Low Energy Beacons RSSI Based Indoor Positioning
Yao, H., Shu, H., Liang, X., Yan, H., & Sun, H. (2020) · IEEE Access · doi:10.1109/access.2020.3038894 · Cited by 33
“The RSSI based positioning methods commonly used can be divided into range-free methods and range-based methods [35], a classic range-free method based on RSSI is the fingerprinting positioning method as in [26], [28].”
MethodFlueratoru, L., Shubina, V., Niculescu, D., & Lohan, E. S. (2021) · IEEE Sensors Journal · doi:10.1109/jsen.2021.3095710 · Cited by 34
“Second, embedded antennas usually do not have a flat response over the entire bandwidth, resulting in different gains depending on the frequency [25].”
BackgroundKe, C.-K., Wu, M.-Y., Chan, Y.-W., & Lu, K.-C. (2018) · Energies · doi:10.3390/en11123464 · Cited by 33
“The RSSI of multiple BLE Beacons is used to identify the user area, and then, the positioning algorithm is used to estimate their location [9,13].”
MethodFrom Conception to Retirement: A Lifetime Story of a 3-Year-Old Wireless Beacon System in the Wild
Ding, Y. C., Liu, L., Yang, Y., Liu, Y., Zhang, D., & He, T. (2021) · IEEE/ACM Transactions on Networking · doi:10.1109/tnet.2021.3107043 · Cited by 34
Murad, S. S., Yussof, S., & Badeel, R. (2022) · Sensors · doi:10.3390/s22062313 · Cited by 32
RSSI or Time-of-flight for Bluetooth Low Energy based localization? An experimental evaluation
Giovanelli, D., & Farella, E. (2018) · IFIP Wireless and Mobile Networking Conference (WMNC) · doi:10.23919/wmnc.2018.8480847 · Cited by 32
“To overcome the effects of reflections and the non-idealities of indoor propagation, data-based (or RSSI-fingerprintingbased) techniques can be applied [3, 11, 12, 13].”
MethodBLE Neighbor Discovery Parameter Configuration for IoT Applications
Luo, B., Xiang, F. H., Sun, Z., & Yao, Y. (2019) · IEEE Access · doi:10.1109/access.2019.2912493 · Cited by 32
A Framework for Infrastructure-Free Indoor Localization Based on Pervasive Sound Analysis
Leonardo, R., Barandas, M., & Gamboa, H. F. S. (2018) · IEEE Sensors Journal · doi:10.1109/jsen.2018.2817887 · Cited by 31
An Interactive Real-Time Locating System Based on Bluetooth Low-Energy Beacon Network †
Lin, Y.-W., & Lin, C.-Y. (2018) · Sensors · doi:10.3390/s18051637 · Cited by 31
“Faragher and Harle [16] explored fingerprint positioning using BLE beacons.”
An Improved Vision-Based Indoor Positioning Method
Yang, S., Ma, L., Jia, S., & Qin, D. (2020) · IEEE Access · doi:10.1109/access.2020.2968958 · Cited by 31
Identifying the BLE Advertising Channel for Reliable Distance Estimation on Smartphones
Gentner, C., Günther, D., & Kindt, P. H. (2022) · IEEE Access · doi:10.1109/access.2022.3140803 · Cited by 31
“Localization using Fingerprinting: Instead of directly estimating the distance between two devices, fingerprinting approaches [11], [32], [33] can recognize different previously recorded device positions.”
BackgroundTomažič, S., & Škrjanc, I. (2021) · Sensors · doi:10.3390/s21082857 · Cited by 31
“, models of signal strengths (and use trilateration) [1,11,24]; and methods based on the principle of “fingerprints” [21,42].”
BackgroundMethodKawecki, R., Hausman, S., & Korbel, P. (2022) · Remote Sensing · doi:10.3390/rs14091992 · Cited by 31
“To gather the data, various sensors and methods have been explored [5,13].”
BackgroundMethodMillimeter-Wave Radar Localization Using Indoor Multipath Effect
Hao, Z., Yan, H., Dang, X., Ma, Z., Jin, P., & Ke, W. (2022) · Sensors · doi:10.3390/s22155671 · Cited by 31
“With the development of sensing technologies, the indoor positioning tasks of electronic devices can be achieved using popular wireless infrastructures, such as commercial Wi-Fi devices, Bluetooth devices, Ultra Wide Band (UWB) devices, Radio Frequency Identification (RFID) devices, cameras, and millimeter-wave radar.”
BackgroundLoRaWAN: Lost for Localization?
Svertoka, E., Rusu-Casandra, A., Bürget, R., Marghescu, I., Hošek, J., & Ometov, A. (2022) · IEEE Sensors Journal · doi:10.1109/jsen.2022.3212319 · Cited by 37
“One of the most well-known papers [31] presents a comparative study of several technologies, Wi-Fi, BLE, ZigBee, and LoRaWAN, for indoor localization.”
ResultInfluentialReal-Time Indoor Positioning Based on BLE Beacons and Pedestrian Dead Reckoning for Smartphones
Jin, Z., Li, Y., Yang, Z., Zhang, Y., & Cheng, Z. (2023) · Applied Sciences · doi:10.3390/app13074415 · Cited by 31
A Smartphone Indoor Positioning System Using Hybrid Localization Technology
Gang, H.-S., & Pyun, J.-Y. (2019) · Energies · doi:10.3390/en12193702 · Cited by 31
“[17] proposed an indoor positioning method using fingerprinting with BLE beacons that used 19 beacons to construct a fingerprint map for positioning the user.”
MethodCandia, D. A., Játiva, P. P., Azurdia-Meza, C. A., Sánchez, I., & Ijaz, M. (2024) · Applied Sciences · doi:10.3390/app14062514 · Cited by 30
Han, K., Xing, H., Deng, Z., & Du, Y. (2018) · ISPRS International Journal of Geo-Information · doi:10.3390/ijgi7060232 · Cited by 34
Woensel, W. V., Roy, P. C., Abidi, S. S. R., & Abidi, S. (2020) · Artificial Intelligence in Medicine · doi:10.1016/j.artmed.2020.101931 · Cited by 31
An application of metadata-based image retrieval system for facility management
Ma, J. W., Czerniawski, T., & Leite, F. L. (2021) · Advanced Engineering Informatics · doi:10.1016/j.aei.2021.101417 · Cited by 30
Bluetooth-Based Healthcare Information and Medical Resource Management System
Chang, C.-S., Wu, T.-H., Wu, Y., & Han, C. (2023) · Sensors · doi:10.3390/s23125389 · Cited by 30
“Therefore, this study proposes to use fingerprint positioning [41–45] in these dangerous areas to improve the accuracy of positioning to avoid danger to patients or care recipients.”
MethodAn AR mobile navigation system integrating indoor positioning and content recommendation services
Wang, C.-S. (2018) · World Wide Web · doi:10.1007/s11280-018-0580-3 · Cited by 30
“A number of scholars have recently published related studies and applications of BLE beacon positioning [5, 7, 10, 11, 14, 26].”
Improving trilateration for indoors localization using BLE beacons
Blas, A. D., & López–de–Ipiña, D. (2017) · Cited by 29
Lovón-Melgarejo, J., Castillo‐Cara, M., Huarcaya-Canal, O., Orozco–Barbosa, L., & García-Varea, I. (2019) · IEEE Access · doi:10.1109/access.2019.2899736 · Cited by 29
“In previous research [9], Faragher and Harle applied the multipath mitigation algorithm to the RSSI fingerprint of their BLE4.”
BackgroundMethodInfluentialChan, R. Y.-Y., Sato-Shimokawara, E., Bai, X., Motohashi, Y., Kuo, S.-W., & Chung, A. (2019) · IEEE Systems Journal · doi:10.1109/jsyst.2019.2911671 · Cited by 30
“iments have shown significant positioning improvement of BLE over de-facto localization techniques, such as GPS and WiFi localization [35], especially in the indoor environment.”
BackgroundMethodResultInfluentialIndoor positioning system using hybrid method of fingerprinting and pedestrian dead reckoning
Riady, A., & Kusuma, G. P. (2021) · Journal of King Saud University - Computer and Information Sciences · doi:10.1016/j.jksuci.2021.09.005 · Cited by 31
“Based on (Davidson and Piche, 2016; Faragher and Harle, 2015) BLE is more advantageous than Wi-Fi in Indoor Positioning System because of the lower cost on hardware, energy consumption and BLE with shorter channel width with 3 dedicated advertisement channels will support transferring small chunks…”
Metadata
- Authors
- Faragher, R., & Harle, R.
- Affiliations
- University of Cambridge (GB)
- Venue
- IEEE Journal on Selected Areas in Communications
- Published
- 2015-11
- Volume
- 33
- Issue
- 11
- Pages
- 2418-2428
- ISSN
- 0733-8716 (ISSN-L)
- OpenAlex
- W1893431417
- Cited by
- 879
- References
- 21
- Citations by year
- 2026: 39 · 2025: 70 · 2024: 63 · 2023: 63 · 2022: 82 · 2021: 105 · 2020: 114 · 2019: 111 · 2018: 114 · 2017: 76 · 2016: 38 · 2015: 3
- FWCI
- 37.13
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- IEEE Journal on Selected Areas in Communications (publishedVersion)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Indoor and Outdoor Localization Technologies
- Physical Sciences › Computer Science › Computer Networks and Communications › Bluetooth and Wireless Communication Technologies
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Optical Wireless Communication Technologies
- Keywords
- Bluetooth Low Energy, location fingerprinting, indoor positioning, radio maps, beacons, fast fading, power consumption, transmission power
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.