Location Fingerprinting With Bluetooth Low Energy Beacons
The DOI matches its Crossref record; 21 of the 21 references it cites were found in a registry or an index.
Abstract
The complexity of indoor radio propagation has resulted in location-awareness being derived from empirical fingerprinting techniques, where positioning is performed via a previously-constructed radio map, usually of WiFi signals. The recent introduction of the Bluetooth Low Energy (BLE) radio protocol provides new opportunities for indoor location. It supports portable battery-powered beacons that can be easily distributed at low cost, giving it distinct advantages over WiFi. However, its differing use of the radio band brings new challenges too. In this work, we provide a detailed study of BLE fingerprinting using 19 beacons distributed around a ~600 m2testbed to position a consumer device. We demonstrate the high susceptibility of BLE to fast fading, show how to mitigate this, and quantify the true power cost of continuous BLE scanning. We further investigate the choice of key parameters in a BLE positioning system, including beacon density, transmit power, and transmit frequency. We also provide quantitative comparison with WiFi fingerprinting. Our results show advantages to the use of BLE beacons for positioning. For one-shot (push-to-fix) positioning we achieve2), compared to2) and <; 8.5 m for an established WiFi network in the same area.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“Because the Wi-Fi APs and BLE beacons share the same frequency range (2.4 GHz) there may be interference problems [15], although: (1) interference problems usually occur when the number of access points is very large, something that did not happen in our case; (2) possible interference problems could be overcome by avoiding certain channels and taking into account the fact that Bluetooth”
From Study on an Indoor Positioning System for Harsh Environments Based on Wi-Fi and Bluetooth Low Energy (2017) · cites this paper as [15]
In the citing paper
“this is simply the consequence of the fact that BLE technology transmits advertisements on these channels to mitigate interference with other devices [15].”
From Study on an Indoor Positioning System for Harsh Environments Based on Wi-Fi and Bluetooth Low Energy (2017) · cites this paper as [15]
Citations
Cites
Survey of Wireless Indoor Positioning Techniques and Systems
Liu, H., Darabi, H., Banerjee, P., & Liu, J. (2007) · IEEE Transactions on Systems, Man and Cybernetics, Part C (Applications and Reviews) · doi:10.1109/tsmcc.2007.905750 · Cited by 4,098 · cited 1×
“Indoor positioning is a mature research field, with many proposed technologies and techniques—comprehensive overviews can be found in [19], [18], [2].”
BackgroundThe Horus WLAN location determination system
Youssef, M., & Agrawala, A. (2005) · Proceedings of the 3rd international conference on Mobile systems, applications, and services · doi:10.1145/1067170.1067193 · Cited by 1,653 · cited 1×
“Here the focus is on radio positioning, specifically using the empirical fingerprinting techniques [3], [15], [17], [22] that avoid the need to model the complex radio propagation environment indoors by patternmatching to a previously surveyed map of radio signal strengths.”
BackgroundA Survey of Indoor Inertial Positioning Systems for Pedestrians
Harle, R. (2013) · IEEE Communications Surveys & Tutorials · doi:10.1109/surv.2012.121912.00075 · Cited by 814 · cited 1×
“fingerprints with other sources to form hybrid systems, many of which are based on the idea of Simultaneous Localization and Mapping (SLAM) [10], [16] being applied to pedestrian dead reckoning [13].”
BackgroundSelf-citationWiFi-SLAM Using G aussian Process Latent Variable Models
Ferris, B., Fox, D., & Lawrence, N. D. (2007) · International Joint Conference on Artificial Intelligence · Cited by 610
Network Time Protocol Version 4: Protocol and Algorithms Specification
Mills, D., Burbank, J., & Kasch, W. (2010) · doi:10.17487/rfc5905 · Cited by 577
A comparative survey of WLAN location fingerprinting methods
Honkavirta, V., Perala, T., Ali-Loytty, S., & Piche, R. (2009) · 2009 6th Workshop on Positioning, Navigation and Communication · doi:10.1109/wpnc.2009.4907834 · Cited by 522
Enhancements to the RADAR User Location and Tracking System
Bahl, V., & Padmanabhan, V. (2000) · Cited by 507
Implementing a sentient computing system
Addlesee, M., Curwen, R., Hodges, S., Newman, J., Steggles, P., Ward, A., & Hopper, A. (2001) · Computer · doi:10.1109/2.940013 · Cited by 490 · cited 1×
“Ground Truth Location: The Active Bat system [1] was available throughout the testbed and was used to provide ground truth position.”
MethodA Survey of Indoor Positioning and Object Locating Systems
Koyuncu, H., & Yang, S. H. (2010) · Cited by 251
COMPASS: A probabilistic indoor positioning system based on 802.11 and digital compasses
King, T., Kopf, S., Haenselmann, T., Lubberger, C., & Effelsberg, W. (2006) · Proceedings of the 1st international workshop on Wireless network testbeds, experimental evaluation & characterization · doi:10.1145/1160987.1160995 · Cited by 223
Research works printed but not linked: 2
- ferris, 0, WiFi-SLAM using Gaussian process latent variable models, Proc 20th IJCAI, 2480
- 2010, Bluetooth Specification Version 4 0
Cited by
Items 201–300 of 917
A Kernel Method to Nonlinear Location Estimation With RSS-Based Fingerprint
Ng, P. C., Spachos, P., She, J. P. M., & Plataniotis, K. N. (2022) · IEEE Transactions on Mobile Computing · doi:10.1109/tmc.2022.3162612 · Cited by 30
“The k nearest neighbor (kNN) is the commonly used classification method for many fingerprint-based localizations, including the fingerprint-based on WiFi [32] and beacon [11].”
BackgroundMethodInfluentialIndoor localization algorithms based on Angle of Arrival with a benchmark comparison
Furfari, F., Girolami, M., Mavilia, F., & Barsocchi, P. (2024) · Ad Hoc Networks · doi:10.1016/j.adhoc.2024.103691 · Cited by 28
Martín-Frechina, S., Dura, E., Miralles, I., & Torres-Sospedra, J. (2025) · Sensors · doi:10.3390/s25226946 · Cited by 28
“Years later, with the advent of Bluetooth Low Energy (BLE) [2] in around 2015, similar fingerprinting strategies were adapted to BLE bea-cons, taking advantage of the technology’s low power consumption and its compatibility with mobile devices.”
Application of Supervised Learning Approach for Target Localization in Wireless Sensor Network
Jondhale, S. R., Shubair, R. M., Labade, R. P., Lloret, J., & Gunjal, P. R. (2020) · Advances in intelligent systems and computing · doi:10.1007/978-3-030-40305-8_24 · Cited by 28
Epidemic contact tracing with smartphone sensors
Nguyen, K. A., Luo, Z., & Watkins, C. (2020) · Journal of Location Based Services · doi:10.1080/17489725.2020.1805521 · Cited by 28
Evaluation of an Indoor Localization Solution Based on Bluetooth Low Energy Beacons
Obreja, S. G., & Vulpe, A. (2020) · International Conference on Communications (COMM) · doi:10.1109/comm48946.2020.9141987 · Cited by 28
“The main drawback of these solutions is that they require an extensive measurements campaign and a careful calibration of the transmitted signal strength to build the signal map [5-8].”
BackgroundMethodA Comparison of Wireless Standards in IoT for Indoor Localization Using LoPy
Khan, F. U., Awais, M., Rasheed, M. B., Masood, B., & Ghadi, Y. Y. (2021) · IEEE Access · doi:10.1109/access.2021.3076371 · Cited by 28
Improved Smartphone-Based Indoor Pedestrian Dead Reckoning Assisted by Visible Light Positioning
Wang, Y., & Zhao, H. (2018) · IEEE Sensors Journal · doi:10.1109/jsen.2018.2888493 · Cited by 28
BLE-Based Indoor Tracking System with Overlapping-Resistant IoT Solution for Tourism Applications
Belka, R., Deniziak, S. R., Łukawski, G., & Pięta, P. (2021) · Sensors · doi:10.3390/s21020329 · Cited by 27
“In [18], BLE was applied in offline training as well as online locating phases of the ILS.”
MethodVisual Map Construction Using RGB-D Sensors for Image-Based Localization in Indoor Environments
Feng, G., Ma, L., & Tan, X. (2017) · Journal of Sensors · doi:10.1155/2017/8037607 · Cited by 28
A BLE-Based Pedestrian Navigation System for Car Searching in Indoor Parking Garages
Wang, S.-S. (2018) · Sensors · doi:10.3390/s18051442 · Cited by 26
“The micro-location technique based on beacon technology provides another localization technique in the indoor environment [13–16].”
MethodEmbracing Consumer-level UWB-equipped Devices for Fine-grained Wireless Sensing
Zhang, F., Chang, Z., Xiong, J., Ma, J., Ni, J., Zhang, W., Jin, B., & Zhang, D. (2022) · Proceedings of the ACM on Interactive Mobile Wearable and Ubiquitous Technologies · doi:10.1145/3569487 · Cited by 45
“In recent years, a large variety of RF techniques have been employed for sensing including WiFi [28, 40, 41, 61], RFID [44], Bluetooth [34], FMCW radar [27, 68, 69], LoRa [30, 56, 57, 62, 63], and LTE [31, 35, 45].”
BackgroundSupport Vector Regression for Bluetooth Ranging in Multipath Environments
Marter, J. P. V., Dabak, A. G., Al‐Dhahir, N., & Torlak, M. (2023) · IEEE Internet of Things Journal · doi:10.1109/jiot.2023.3244743 · Cited by 26
“To mitigate these effects, RSSI-based techniques most often utilize multiple nodes and many measurements over time in combination with filtering or fingerprinting [44], [45], [46], [47].”
BackgroundMethodEfficient IoT Devices Localization Through Wi-Fi CSI Feature Fusion and Anomaly Detection
Li, Y., Yang, J., Shih, S.-L., Shih, W.-T., Wen, C.-K., & Jin, S. (2024) · IEEE Internet of Things Journal · doi:10.1109/jiot.2024.3421577 · Cited by 29
“While the Global Positioning System (GPS) [6] offers precise outdoor location tracking, its efficacy diminishes indoors due to signal obstructions disrupting line-of-sight (LoS) paths to satellites.”
BackgroundSmart hospital infrastructure: geomagnetic in-hospital medical worker tracking
Yamashita, K., Oyama, S., Otani, T., Yamashita, S., Furukawa, T., Kobayashi, D., Sato, K., Sugano, A., Funada, C., Mori, K., et al. (2020) · Journal of the American Medical Informatics Association · doi:10.1093/jamia/ocaa204 · Cited by 26
Features based proximity localization with Bluetooth emitters
Bouchard, K., Ramezani, R., & Naeim, A. (2016) · IEEE Annual Ubiquitous Computing, Electronics & Mobile Communication Conference (UEMCON) · doi:10.1109/uemcon.2016.7777845 · Cited by 25
“Faragher and Harle [12] implemented this method with Bluetooth beacons.”
BackgroundMethodInfluentialPush the Limit of Highly Accurate Ranging on Commercial UWB Devices
Ma, J., Zhang, F., Jin, B., Chang, S., Li, S., Wang, Z., & Ni, J. (2024) · Proceedings of the ACM on Interactive Mobile Wearable and Ubiquitous Technologies · doi:10.1145/3659602 · Cited by 25
“Consequently, Bluetooth localization systems often rely on RSSI fingerprint-based methods [28, 37], which have a low power consumption and cost.”
BackgroundIndoor Location Learning Over Wireless Fingerprinting System With Particle Markov Chain Model
Sou, S., Lin, W.-H., Lan, K.-C., & Lin, C.-S. (2019) · IEEE Access · doi:10.1109/access.2019.2890850 · Cited by 29
“Therefore, the use of BLE beacons is an alternative for ILBS [21].”
MethodInfluentialTrilateration, Fingerprinting, and Centroid: Taking Indoor Positioning with Bluetooth LE to the Wild
Kluge, T., Groba, C., & Springer, T. (2020) · IEEE International Symposium on a World of Wireless, Mobile and Multimedia Networks (WoWMoM) · doi:10.1109/wowmom49955.2020.00054 · Cited by 25
“Compared to WiFi, BLE is especially prone to fast fading because of its narrow channel width [5].”
BackgroundMethodInfluentialD-PARK: User-Centric Smart Parking System over BLE-Beacon Based Internet of Things
Park, S. (2021) · Electronics · doi:10.3390/electronics10050541 · Cited by 25
“Up-to-date research has proposed more accurate localization or indoor position-based applications [14,16].”
BackgroundInfluentialiBeacon enabled indoor positioning for warehouse management
Zhao, Z., Fang, J., Huang, G. Q., & Zhang, M. (2016) · International Symposium on Computational and Business Intelligence (ISCBI) · doi:10.1109/iscbi.2016.7743254 · Cited by 24
“This has led us to employ other technology for indoor positioning.”
MethodTrilateration With BLE RSSI Accounting for Pathloss Due to Human Obstacles
Naghdi, S., & O’Keefe, K. (2019) · International Conference on Indoor Positioning and Indoor Navigation · doi:10.1109/ipin.2019.8911816 · Cited by 24
Retscher, G., & Leb, A. (2021) · Sensors · doi:10.3390/s21020432 · Cited by 24
“Advantages of Bluetooth are availability as it is supported by most smartphones, low cost, and low power consumption, which allows transmitters to run on battery for several months or even years [21].”
BackgroundCombining Multichannel RSSI and Vision with Artificial Neural Networks to Improve BLE Trilateration
Naghdi, S., & O’Keefe, K. (2022) · Sensors · doi:10.3390/s22124320 · Cited by 23
“Another comparison between BLE and Wi-Fi fingerprinting is presented by [8].”
Backgroundde Blasio, G., Rodríguez-Rodríguez, J. C., García, C. R., & Quesada-Arencibia, A. (2019) · Sensors · doi:10.3390/s19143087 · Cited by 27
“The use of BLE technology applied to indoor positioning (IP) has many advantages: The beacons or emitters are portable, battery-powered, small, lightweight, have low energy consumption, give a high positioning accuracy and are easily deployable at low cost [11,12].”
BackgroundPhase Center Offset Calibration and Multipoint Time Latency Determination for UWB Location
Liu, T., Li, B., & Yang, L. (2022) · IEEE Internet of Things Journal · doi:10.1109/jiot.2022.3155736 · Cited by 24
“achieve at most submeter-level accuracy and cannot fully satisfy the accuracy requirements for indoor positioning [7]–[9].”
BackgroundA Succinct Method for Non-Line-of-Sight Mitigation for Ultra-Wideband Indoor Positioning System
Liu, A., Lin, S., Wang, J., & Kong, X. (2022) · Sensors · doi:10.3390/s22218247 · Cited by 23
Smart Parking with Fine-Grained Localization and User Status Sensing Based on Edge Computing
Lee, C., Park, S., Yang, T., & Lee, S.-H. (2019) · IEEE Vehicular Technology Conference · doi:10.1109/vtcfall.2019.8891560 · Cited by 24
“According to a state-of-the-art research [10], the accuracy of WiFi fingerprint with one access point per 100 m2 is 8.5 meter in an indoor place.”
BackgroundMethodInfluentialBias Introduced by True Radiation Patterns in RSS-based Visible Light Positioning
Stevens, N. (2019) · Proceedings of IEEE Sensors/Proceedings of IEEE Sensors ... · doi:10.1109/sensors43011.2019.8956584 · Cited by 23
“The majority of this research is focused on the usage of radio-frequency (RF) signals [1], [2].”
BackgroundAn Improved Bluetooth Indoor Positioning Method Using Dynamic Fingerprint Window
Ruan, L., Zhang, L., Zhou, T., & Long, Y. (2020) · Sensors · doi:10.3390/s20247269 · Cited by 24
“Bluetooth positioning is a hotspot in indoor positioning technology, which has the characteristics of low power consumption, easy deployment, small size, low cost, and high security [1].”
BackgroundAn indoor localization dataset and data collection framework with high precision position annotation
Daniş, F. S., Naskalı, A. T., Cemgil, A. T., & Ersoy, C. (2022) · Pervasive and Mobile Computing · doi:10.1016/j.pmcj.2022.101554 · Cited by 23
“Whereas the localization algorithms have been improved with the ubiquitous Wi-Fi technology for indoors [1], due to its low energy consumption, price and size, Bluetooth Low Energy (BLE) is particularly suited to this domain [2].”
BackgroundBluetooth low energy indoor positioning: A fingerprinting neural network approach
Ferrero-López, A., Gallego, A., & Lozano, M. Á. (2025) · Internet of Things · doi:10.1016/j.iot.2025.101565 · Cited by 22
Rapid BLE Beacon Localization with Range-Only EKF-SLAM Using Beacon Interval Constraint
Sato, A., Nakajima, M., & Kohtake, N. (2019) · International Conference on Indoor Positioning and Indoor Navigation · doi:10.1109/ipin.2019.8911778 · Cited by 24
“As the BLE beacon is easy to mount on an indoor landmark directly and free from consideration of coverage to provide communication services, the dense and flexible deployment of beacons is possible in indoor environment that allows the fine-grained positioning of smartphones [3].”
BackgroundEmpirical Study of a Room-Level Localization System Based on Bluetooth Low Energy Beacons
García-Paterna, P. J., Martinez-Sala, A. S., & Sánchez-Aarnoutse, J. C. (2021) · Sensors · doi:10.3390/s21113665 · Cited by 26
“The fingerprint approach is widespread from Wi-Fi [14] to BLE systems [15] for two main reasons: (1) its simplicity; (2) it is possible to achieve a bounded positioning error of few meters.”
BackgroundMethodStudy workplace space occupancy: a review of measures and technologies
Zhou, Y., Hua, Y., & Liu, J. (2021) · Journal of Facilities Management · doi:10.1108/jfm-01-2021-0013 · Cited by 22
UJAmI Location: A Fuzzy Indoor Location System for the Elderly
Albín-Rodríguez, A.-P., Robles, Y. D. L. F., Ruiz, J. L. L., Espinosa, Á. V., & Espinilla, M. (2021) · International Journal of Environmental Research and Public Health · doi:10.3390/ijerph18168326 · Cited by 22
“An early work in this field was done by Faragher and Harle [26].”
MethodPrivacy-Preserving Individual-Level COVID-19 Infection Prediction via Federated Graph Learning
Fu, W., Wang, H., Gao, C., Liu, G., Li, Y., & Jiang, T. (2024) · ACM Transactions on Information Systems · doi:10.1145/3633202 · Cited by 26
“Nevertheless, several existing researches have claimed that the private information of users can still be divulged via the uploaded gradients [42] or parameters [25, 57].”
BackgroundBouse, L., King, S. A., & Chu, T. (2024) · Sensors · doi:10.3390/s24072088 · Cited by 22
“Fingerprinting essentially compares the current RSSIs of all beacons within range to sets of known RSSI values throughout a specified area [14].”
BackgroundMethodThe EvAAL Evaluation Framework and the IPIN Competitions
Potortì, F., Crivello, A., & Palumbo, F. (2018) · Elsevier eBooks · doi:10.1016/b978-0-12-813189-3.00011-3 · Cited by 24
A CSI-Based Indoor Fingerprinting Localization with Model Integration Approach
Yin, Y., Song, C., Li, M., & Niu, Q. (2019) · Sensors · doi:10.3390/s19132998 · Cited by 24
“Unlike outdoor positioning that uses capitalized GPS based on line-of-sight path to pinpoint the location [1], indoor positioning is often influenced by various environmental factors, such as multipath effect [2], slow decay [3], etc.”
BackgroundChen, L., Chen, T.-P., Chen, H.-M., & Tsai, M. (2019) · IEEE Sensors Journal · doi:10.1109/jsen.2019.2938324 · Cited by 22
“tooth Low Engergy (BLE) iBeacon devices [5]–[9] can be adopted for accurate indoor positioning and efficient peo-”
BackgroundComparison of Neural Network Training Functions for RSSI Based Indoor Localization Problem in WSN
Jondhale, S. R., Sharma, M. K., Maheswar, R., Shubair, R. M., & Shelke, A. (2020) · Advances in intelligent systems and computing · doi:10.1007/978-3-030-40305-8_7 · Cited by 22
A Reliable Smart Interaction With Physical Thing Attached With BLE Beacon
Ng, P. C., She, J. P. M., & Ran, R. (2020) · IEEE Internet of Things Journal · doi:10.1109/jiot.2020.2974230 · Cited by 22
“For example, Faragher and Harle [13] used radio fingerprinting to locate the position of a smart-phone; whereas Xiao et al. [14] constructed a robust 3-”
BackgroundFusion particle and fingerprint recognition for indoor positioning system on mobile
Lamoureux, C., & Chelouah, R. (2020) · Engineering Applications of Artificial Intelligence · doi:10.1016/j.engappai.2020.104082 · Cited by 22
Castillo‐Cara, M., Lovón-Melgarejo, J., Bravo-Rocca, G., Orozco–Barbosa, L., & García-Varea, I. (2017) · Journal of Sensors · doi:10.1155/2017/1928578 · Cited by 21
“0 mainly uses channels 37 (2402MHz), 38 (2426MHz), and 39 (2480MHz) [21].”
Real-World Deployment of Low-Cost Indoor Positioning Systems for Industrial Applications
Silva, I., Pendão, C., & Moreira, A. J. C. (2021) · IEEE Sensors Journal · doi:10.1109/jsen.2021.3103662 · Cited by 22
Shu, Y.-H., Chang, Y.-H., Lin, Y.-Z., & Chow, C. (2024) · Sensors · doi:10.3390/s24165424 · Cited by 21
“…(RF) based IPS, such as Blue-tooth, Wireless Fidelity (WiFi), and wireless local area networks (WLANs) have attracted much attention [1,2]; however, their implementations still face many challenges, such as electromagnetic interference (EMI) with nearby RF devices or limited IPS…”
BackgroundPreliminary design for sustainable BLE Beacons powered by solar panels
Jeon, K. E., Tong, T., & She, J. P. M. (2016) · IEEE Conference on Computer Communications Workshops (INFOCOM WKSHPS) · doi:10.1109/infcomw.2016.7562054 · Cited by 21
Indoor Localization Using Ambient FM Radio RSS Fingerprinting: A 9-Month Study
Popleteev, A. (2017) · IEEE International Conference on Computer and Information Technology (CIT) · doi:10.1109/cit.2017.57 · Cited by 21
“While satellite-based systems like GPS and GLONASS are globally available in clear-sky areas, most of indoor positioning systems are constrained by the required in-building infrastructure — be it Bluetooth beacons [1], Wi-Fi networks [2], or ultrasound and ultrawideband transceivers [3], [4].”
BackgroundAccurate Indoor-Positioning Model Based on People Effect and Ray-Tracing Propagation
Firdaus, F., Ahmad, N. A., & Sahibuddin, S. (2019) · Sensors · doi:10.3390/s19245546 · Cited by 23
“The RF technology used in IPS include WLAN/Wi-Fi [8,9], Bluetooth [10], Zig Bee [11], Radio-frequency identification (RFID) [12], frequency modulation (FM) [13], and ultra-wideband (UWB) [14].”
MethodVivid: Augmenting Vision-Based Indoor Navigation System With Edge Computing
Zhao, W., Xu, L., Qi, B., Hu, J. S., Wang, T., & Runge, T. M. (2020) · IEEE Access · doi:10.1109/access.2020.2978123 · Cited by 26
“Although empirically such accuracy is sufficient for indoor navigation, it has been pointed out that the received signal strength (RSS) method they use is extremely vulnerable to the environment with interferences [4], [5].”
Where are You? Exploring Micro-Location in Indoor Learning Environments
Riquelme, F., Noël, R., Cornide-Reyes, H., Geldes, G., Cechinel, C., Miranda, D., Villarroel, R. H., & Muñoz, R. (2020) · IEEE Access · doi:10.1109/access.2020.3008327 · Cited by 21
“Beacons have several comparative advantages over the previous technologies used for indoor location [20], [21], especially in learning environments prepared to promote collaborative learning.”
BackgroundMultidirectional Differential RSS Technique for Indoor Vehicle Navigation
Park, P., Marco, P. D., Jung, M., Santucci, F., & Sung, T. K. (2022) · IEEE Internet of Things Journal · doi:10.1109/jiot.2022.3199814 · Cited by 21
“Bluetooth beacons transmit their unique identifiers to nearby mobile devices that can autonomously initiate a location-based service based on the signals received by the beacons [46].”
BackgroundMethodInfluentialProposal of Separate Channel Fingerprinting Using Bluetooth Low Energy
Ishida, S., Takashima, Y., Tagashira, S., & Fukuda, A. (2016) · IIAI International Congress on Advanced Applied Informatics (IIAI-AAI) · doi:10.1109/iiai-aai.2016.22 · Cited by 21
An Indoor Positioning-Based Mobile Payment System Using Bluetooth Low Energy Technology
Yohan, A., Lo, N., & winata, D. (2018) · Sensors · doi:10.3390/s18040974 · Cited by 20
“Fingerprinting is another method that can be used to determine the position of target device by means of distance comparisons between the current target device positions with a pre-stored target device position reference [14,20,28].”
MethodGong, X., Liu, J., Yang, S., Gu, F., Huang, G., & Bai, Y. (2022) · IEEE Internet of Things Journal · doi:10.1109/jiot.2022.3207466 · Cited by 20
“Existing indoor positioning solutions apply an array of principles, including angle-of-arrival (AOA) or angleof-departure (AOD) [7], [8], time-of-arrival (TOA) or timedifference-of-arrival (TDOA) [9], [10], received signal strength indication (RSSI) [11], fingerprinting [12], [13], [14], and inertial navigation system…”
BackgroundInvestigations into Bluetooth low energy localization precision limits
Schmalenstroeer, J., & Haeb‐Umbach, R. (2016) · European Signal Processing Conference (EUSIPCO) · doi:10.1109/eusipco.2016.7760329 · Cited by 20
“Bluetooth low energy (BLE) based positioning has recently received remarkable attention due to its low installation costs, broad support by mobile end devices (smartphones) and low energy consumption, both on the beacon and on the mobile device side [9].”
BackgroundEfficient Locality Classification for Indoor Fingerprint-Based Systems
Chow, K.-H., He, S., Tan, J., & Chan, S.-H. G. (2018) · IEEE Transactions on Mobile Computing · doi:10.1109/tmc.2018.2839112 · Cited by 20
“For concreteness, we consider Wi-Fi RSSIs in our expositions and experiments, though INOA is applicable to any existing or emerging fingerprint signals such as Bluetooth [7] or channel state information [8].”
BackgroundDriver and Passenger Identification From Smartphone Data
Ahmad, B. I., Langdon, P., Liang, J., Godsill, S., Delgado, M., & Popham, T. (2018) · IEEE Transactions on Intelligent Transportation Systems · doi:10.1109/tits.2018.2845113 · Cited by 20
“BLE beacons in/on the vehicle [27], [30], [42], [43].”
BackgroundDealing with Insufficient Location Fingerprints in Wi-Fi Based Indoor Location Fingerprinting
Dong, K., Ling, Z., Xia, X., Ye, H., Wu, W., & Yang, M. (2017) · Wireless Communications and Mobile Computing · doi:10.1155/2017/1268515 · Cited by 20
“It is relatively simple to deploy, compared to the otherwireless indoor positioning techniques using Bluetooth beacons [1] or RFID tags [2], which can achieve higher location accuracy.”
MethodMulti-Sensor Fusion Approach for Improving Map-Based Indoor Pedestrian Localization
Huang, H.-Y., Hsieh, C.-Y., Liu, K.-C., Cheng, H.-C., Hsu, S. J.-P., & Chan, C.-T. (2019) · Sensors · doi:10.3390/s19173786 · Cited by 20
milliTRACE-IR: Contact Tracing and Temperature Screening via mmWave and Infrared Sensing
Canil, M., Pegoraro, J., & Rossi, M. (2021) · IEEE Journal of Selected Topics in Signal Processing · doi:10.1109/jstsp.2021.3138632 · Cited by 19
Using RF Transmissions From IoT Devices for Occupancy Detection and Activity Recognition
Li, W., Vishwakarma, S., Tang, C., Woodbridge, K., Piechocki, R. J., & Chetty, K. (2021) · IEEE Sensors Journal · doi:10.1109/jsen.2021.3134895 · Cited by 19
“System [32] uses a finger-printing technique to passive track the personnel’s location depending on the variation in Received Signal Strength (RSS).”
MethodFingerprint-based indoor positioning system using BLE: real deployment study
Safwat, R., Shaaban, E., Al-Tabbakh, S. M., & Emara, K. (2022) · Bulletin of Electrical Engineering and Informatics · doi:10.11591/eei.v12i1.3798 · Cited by 19
“RSSI is the most popular and simplest methods for measuring distances in localization [5], [6].”
MethodDevice discovery and tracing in the Bluetooth Low Energy domain
Locatelli, P., Perri, M., Jimenez-Gutierrez, D. M., Lacava, A., & Cuomo, F. (2023) · Computer Communications · doi:10.1016/j.comcom.2023.02.008 · Cited by 22
A survey and future outlook on indoor location fingerprinting privacy preservation
Fathalizadeh, A., Moghtadaiee, V., & Alishahi, M. (2025) · Computer Networks · doi:10.1016/j.comnet.2025.111199 · Cited by 19
“Fingerprinting is a widely used indoor location technique that utilizes Wi-Fi, BLE, FM, AM, and ZigBee wireless access technologies [26, 27, 4, 5, 28].”
IWKNN: An Effective Bluetooth Positioning Method Based on Isomap and WKNN
Wang, Q., Feng, Y., Zhang, X., Sun, Y., & Lu, X. (2016) · Mobile Information Systems · doi:10.1155/2016/8765874 · Cited by 19
Bluetooth positioning based on weighted K-nearest neighbors and adaptive bandwidth mean shift
Wang, Q., Sun, R., Zhang, X., Sun, Y., & Lu, X. (2017) · International Journal of Distributed Sensor Networks · doi:10.1177/1550147717706681 · Cited by 19
Huang, C., Liu, H., Wang, W., & Li, J. (2020) · IEEE Internet of Things Journal · doi:10.1109/jiot.2019.2958455 · Cited by 19
“The accuracy related to the parameters, such as the density, advertising interval, transmission power, etc., are fully discussed in [7].”
BackgroundKalman Filtering-Aided Hybrid Indoor Positioning System With Fingerprinting And Multilateration
Eyng, A. C., Rayel, O. K., Oroski, E., & Rebelatto, J. L. (2020) · IEEE Vehicular Technology Conference · doi:10.1109/vtc2020-spring48590.2020.9129422 · Cited by 21
“In [8], the authors show that BLE-based IPS are in fact capable of outperforming the accuracy of Wi-Fi FP-based IPS, depending on the density of the BLE network.”
BackgroundMethodThe Wisdom of 1,170 Teams: Lessons and Experiences from a Large Indoor Localization Competition
Hu, Y., Fan, X., Yin, Z., Qian, F., Ji, Z., Shu, Y., Han, Y., Xu, Q., Liu, J., & Bahl, P. (2023) · ACM Annual International Conference on Mobile Computing and Networking (MobiCom) · doi:10.1145/3570361.3592507 · Cited by 18
“, radio and acoustic signals), and many researchers leverage fingerprinting-based techniques [2, 12, 20, 48, 57, 62] to estimate the target’s location.”
BackgroundPeng, Y., Niu, X., Tang, J., Mao, D., & Qian, C. (2018) · Sensors · doi:10.3390/s18103419 · Cited by 18
Indoor 3D visible light positioning system based on adaptive parameter particle swarm optimisation
Xu, S., Wu, Y., Wang, X., & Wei, F. (2020) · IET Communications · doi:10.1049/iet-com.2019.1141 · Cited by 18
Position Tracking Techniques Using Multiple Receivers for Anti-Drone Systems
Shin, J., Kim, Y.-S., Ban, T.-W., Choi, S., Kang, K., & Ryu, J.-Y. (2020) · Sensors · doi:10.3390/s21010035 · Cited by 18
“…BLE-based location tracking techniques is based on a fingerprint-ing approach while using the received signal strength indication (RSSI) database [23–25], tracking an object’s position while using the trilateration method, and the RSSI-distance conversion formula using a propagation model…”
MethodSelf-Calibrating Indoor Localization with Crowdsourcing Fingerprints and Transfer Learning
Xiang, C., Zhang, S., Xu, S., & Alexandropoulos, G. C. (2021) · International Conference on Communications · doi:10.1109/icc42927.2021.9500623 · Cited by 18
“…with the inertial navigation system (INS) [3] provides satisfying accuracy, there are still diversified solutions in the indoor case, such as those based on the low-cost Blue-tooth Low Energy (BLE) [4], the increasingly popular 3GPP LTE/5G [5], and the widely deployed WiFi technologies [6]– [11].”
BackgroundHuan, H., Wang, K., Xie, Y., & Zhou, L. (2022) · IEEE Sensors Journal · doi:10.1109/jsen.2022.3227539 · Cited by 18
“To solve this problem, many scholars have conducted research and proposed indoor location systems based on various wireless technologies, such as radio frequency identification (RFID) [3], ZigBee [4], Bluetooth [5], and Wi-Fi [6].”
BackgroundEfficient Sequence Matching and Path Construction for Geomagnetic Indoor Localization
Wu, H., He, S., & Chan, S.-H. G. (2017) · International Conference on Embedded Wireless Systems and Networks · doi:10.5555/3108009.3108030 · Cited by 21
A CrowdSensing-based approach for proximity detection in indoor museums with Bluetooth tags
Girolami, M., Rosa, D. L., & Barsocchi, P. (2023) · Ad Hoc Networks · doi:10.1016/j.adhoc.2023.103367 · Cited by 17
Building a connected BLE mesh: A network inference study
Chiumento, A., Reynders, B., Murillo, Y., & Pollin, S. (2018) · IEEE Wireless Communications and Networking Conference Workshops (WCNCW) · doi:10.1109/wcncw.2018.8369004 · Cited by 17
“Increasing interest has been shown by the industrial community to use BLE for critical, indoor applications such as localisation [1], continuous biometric readings in health structures [2], [3] and industry floor monitoring [4].”
BackgroundDesign and development of a smart attendance management system with Bluetooth low energy beacons
Zorić, B., Dudjak, M., Bajer, D., & Martinović, G. (2019) · Zooming Innovation in Consumer Technologies Conference (ZINC) · doi:10.1109/zinc.2019.8769433 · Cited by 17
“6m inside a 30m2 area [21].”
Akbari, A., Solis, R., Jafari, R., & Mortazavi, B. J. (2020) · IEEE Journal of Biomedical and Health Informatics · doi:10.1109/jbhi.2020.2966151 · Cited by 21
Factor Optimization for the Design of Indoor Positioning Systems Using a Probability-Based Algorithm
Pinto, B. H. O. U. V., Oliveira, H. A. B. F., & Souto, E. (2021) · Journal of Sensor and Actuator Networks · doi:10.3390/jsan10010016 · Cited by 22
“Because of the high RSS variability, a technique usually employed for improving localization systems accuracy in practice consists of collecting more than one RSS sample during a determined time window [36,37].”
MethodA Wi-Fi Fingerprint Positioning Method Based on RLWKNN
Leng, Y., Huang, F., & Tan, W. (2024) · IEEE Sensors Journal · doi:10.1109/jsen.2024.3476335 · Cited by 16
Improving the efficiency and responsiveness of smart objects using adaptive BLE device discovery
Renzler, T., Spörk, M., Boano, C. A., & Römer, K. (2018) · doi:10.1145/3213299.3213306 · Cited by 16
“A large body of works has focused on BLE technology, especially on the provision of services such as neighbor discovery [16], in-door localization [7], group management [11], and locality-based authorization [10], as well as on the design of new platforms [3].”
BackgroundDenoising-Contractive Autoencoder for Robust Device-Free Occupancy Detection
Ng, P. C., & She, J. P. M. (2019) · IEEE Internet of Things Journal · doi:10.1109/jiot.2019.2929822 · Cited by 17
“Previous work [10] has shown that BLE beacons are the potential infrastructure for RF fingerprint in comparison to the WiFi access points.”
InfluentialWBF-PS: WiGig Beam Fingerprinting for UAV Positioning System in GPS-denied Environments
Hong, P.-Y., Li, C.-Y., Chang, H.-R., Hsueh, Y., & Wang, K. (2020) · IEEE Conference on Computer Communications (INFOCOM) · doi:10.1109/infocom41043.2020.9155468 · Cited by 18
“The ones operating below and at 5 GHz have been explored for many years, such as Wi-Fi [14]–[19], Bluetooth [20], and Zigbee [21].”
BackgroundGNSS Repeater Based Differential Indoor Positioning With Multi-Epoch Measurements
Li, X. (2021) · IEEE Transactions on Intelligent Vehicles · doi:10.1109/tiv.2021.3119755 · Cited by 16
“TheapplicationofBluetoothbasedpositioning isconstrainedbythelongscanningtime,particularlyforthe systemwithreal-timerequirement[4],andWi-Fifingerprint basedpositioningsuffersfromtime-consumingsurveyofagiven environment.”
BackgroundInfluentialContact Information-Based Indoor Pedestrian Localization Using Bluetooth Low Energy Beacons
Shiraki, S., & Shioda, S. (2022) · IEEE Access · doi:10.1109/access.2022.3222301 · Cited by 16
“A previous study [18] investigated the key parameters required to realize accurate indoor positioning using BLE radio signals.”
BackgroundOptimizing Placement and Number of RF Beacons to Achieve Better Indoor Localization
Falque, R., Patel, M., & Biehl, J. T. (2018) · Proceedings - IEEE International Conference on Robotics and Automation/Proceedings · doi:10.1109/icra.2018.8460202 · Cited by 16
“Various solutions based on the Bluetooth Low Energy (BLE) technology [5], [7] have been proposed.”
BackgroundInfluentialIndoor Positioning System using Regression-based Fingerprint Method
Ghozali, R. P., & Putra, G. (2019) · International Journal of Advanced Computer Science and Applications · doi:10.14569/ijacsa.2019.0100829 · Cited by 19
“Example of probabilistic methods is: Gaussian process [3] [4].”
BackgroundMethodInfluentialIndoor Positioning System Using Dynamic Model Estimation
Assayag, Y., Oliveira, H. A. B. F., Souto, E., Barreto, R., & Pazzi, R. W. (2020) · Sensors · doi:10.3390/s20247003 · Cited by 17
“Thus, with the development of Bluetooth Low Energy (BLE), it has become increasingly common to employ this technology due to its low energy consumption, ease of deployment, and low cost [7].”
BackgroundLiu, H., Xue, H., Zhao, L., Chen, D., Peng, Z., & Zhang, G. (2023) · IEEE Transactions on Visualization and Computer Graphics · doi:10.1109/tvcg.2023.3321088 · Cited by 16
“Methods using RSSI are proposed [7,11,14], which also suffer from large error.”
MethodImplementation and analysis of Hybrid Wireless Indoor Positioning with iBeacon and Wi-Fi
Chiu, C.-C., Hsu, J.-C., & Leu, J. (2016) · International Congress on Ultra Modern Telecommunications and Control Systems and Workshops (ICUMT) · doi:10.1109/icumt.2016.7765336 · Cited by 15
“Here the focus is on WiFi and BLE indoor positioning, specifically using the fingerprinting techniques [8].”
MethodEnhanced Channel Access for Connection State of Bluetooth Low Energy Networks
Jeon, W. S., & Jeong, D. G. (2017) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2017.2675915 · Cited by 17
“In [13], it is demonstrated that the BLE beacon-based fingerprinting provides more accurate indoor positioning performance as compared with WiFi fingerprinting.”
Beacon-Based Time-Spatial Recognition toward Automatic Daily Care Reporting for Nursing Homes
Morita, T., Taki, K., Fujimoto, M., Suwa, H., Arakawa, Y., & Yasumoto, K. (2018) · Journal of Sensors · doi:10.1155/2018/2625195 · Cited by 19
“Location estimation techniques have been proposed based on several kinds of techniques, including Wi-Fi signals [26], BLE signals [3, 4, 27], magnetic fields [28], infrared [29], and ultrasounds [30].”
Global map matching using BLE beacons for indoor route and stay estimation
Yamamoto, D., Tanaka, R., Kajioka, S., Matsuo, H., & Takahashi, N. (2018) · ACM SIGSPATIAL International Conference on Advances in Geographic Information Systems (SIGSPATIAL GIS) · doi:10.1145/3274895.3274918 · Cited by 15
“In addition, research on location estimation using BLE beacons also include the proximity method [15], particle filtering method [6, 23], trilateration [2], and fingerprint method [8, 13].”
MethodJadidi, M. G., Patel, M., & Miró, J. V. (2017) · Proceedings - IEEE International Conference on Robotics and Automation/Proceedings · doi:10.1109/icra.2017.7989743 · Cited by 18
“Unlike WiFi, BLE uses 40 channels each with a width of 2 MHz [20].”
MethodAutomated Calibration of RSS Fingerprinting Based Systems Using a Mobile Robot and Machine Learning
Kołakowski, M. (2021) · Sensors · doi:10.3390/s21186270 · Cited by 15
Chen, F., Huang, N., & Gong, C. (2022) · Optics Express · doi:10.1364/oe.467663 · Cited by 15
A Radio-Inertial Localization and Tracking System with BLE Beacons Prior Maps
Jadidi, M. G., Patel, M., Miro, J. V., Dissanayake, G., Biehl, J. T., & Girgensohn, A. (2018) · International Conference on Indoor Positioning and Indoor Navigation · doi:10.1109/ipin.2018.8533827 · Cited by 17
“WiFi or radio signal fingerprint-based indoor positioning has become the standard approach for commercial applications [4], [5], [17], [18], [19].”
Background
Metadata
- Authors
- Faragher, R., & Harle, R.
- Affiliations
- University of Cambridge (GB)
- Venue
- IEEE Journal on Selected Areas in Communications
- Published
- 2015-11
- Volume
- 33
- Issue
- 11
- Pages
- 2418-2428
- ISSN
- 0733-8716 (ISSN-L)
- OpenAlex
- W1893431417
- Cited by
- 879
- References
- 21
- Citations by year
- 2026: 39 · 2025: 70 · 2024: 63 · 2023: 63 · 2022: 82 · 2021: 105 · 2020: 114 · 2019: 111 · 2018: 114 · 2017: 76 · 2016: 38 · 2015: 3
- FWCI
- 37.13
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- IEEE Journal on Selected Areas in Communications (publishedVersion)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Indoor and Outdoor Localization Technologies
- Physical Sciences › Computer Science › Computer Networks and Communications › Bluetooth and Wireless Communication Technologies
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Optical Wireless Communication Technologies
- Keywords
- Bluetooth Low Energy, location fingerprinting, indoor positioning, radio maps, beacons, fast fading, power consumption, transmission power
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.