Wideband Receiver for a Three-Dimensional Ranging LADAR System
The DOI matches its Crossref record; 20 of the 21 references it cites were found in a registry or an index.
Abstract
A low-noise, high-gain, wide-linear-dynamic-range, wide-band receiver for a pulsed, direct, three-dimensional ranging LADAR system has been designed and implemented in a 0.13 μm CMOS technology. Specific design techniques, including gain control scheme to widen linear dynamic range, gain allocating between blocks and noise minimization to improve SNR, frequency response compensation to extend bandwidth and ensure system stability, and output voltage swing boosting, have been proposed to achieve challenging design goals with linear dynamic range of 1:1600, equivalent input-referred current noise of less than 5.6 pA/√Hz, high gain of 78 dBΩ, maximum output swing of at least 500 mV, bandwidth of at least 500 MHz, and low sensitivity to temperature variation over the range from -10°C to 60°C, in the presence of 2 pF photodiode parasitic capacitance.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“Ref. [21] demonstrated a dual-mode AFE preamplifier which could be configured as a charge-sensitive amplifier (CSA) or as a gated active load-assisted (GALA) TIA, depending upon the intensity of the input current, thereby extending the dynamic range to 96dB.Yet, the bandwidth shrunk down to 98 MHz in CSA mode from 230 MHz in GALA-TIA.Also, the power dissipation was still large owing to the dual”
From A CMOS Optoelectronic Transimpedance Amplifier Using Concurrent Automatic Gain Control for LiDAR Sensors (2024) · cites this paper as [21]
Citations
Cites
Analog integrated circuit design
Hurst, S. L. (1998) · Microelectronics Journal · doi:10.1016/s0026-2692(97)00051-7 · Cited by 1,732
A 4-MHz CMOS continuous-time filter with on-chip automatic tuning
Krummenacher, F., & Joehl, N. (1988) · IEEE Journal of Solid-State Circuits · doi:10.1109/4.315 · Cited by 697 · cited 1×
“The cross-coupled source degeneration technique [17], which is based on the dynamic resistance degeneration principle [18] is used to improve the linearity.”
Method(2003) · Convergence Technologies for 3G Networks · doi:10.1002/0470860936.ch2 · Cited by 243
Buller, G., & Wallace, A. (2007) · IEEE Journal of Selected Topics in Quantum Electronics · doi:10.1109/jstqe.2007.902850 · Cited by 189
A new compact temperature-compensated CMOS current reference
Fiori, F. L., & Crovetti, P. (2005) · IEEE Transactions on Circuits and Systems II Analog and Digital Signal Processing · doi:10.1109/tcsii.2005.852529 · Cited by 127 · cited 1×
“Moreover, temperature-compensated current [19] is used to generate bias voltages to further reduce the sensitivity of WBRx to temperature variation.”
MethodA high-precision time-to-digital converter for pulsed time-of-flight laser radar applications
Maatta, K. E., & Kostamovaara, J. (1998) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/19.744201 · Cited by 118
Nissinen, J., Nissinen, I., & Kostamovaara, J. (2009) · IEEE Journal of Solid-State Circuits · doi:10.1109/jssc.2009.2017006 · Cited by 103 · cited 1×
“Namely, pulse length [4], amplitude [6], slew rate [7], or unipolar-to-bipolar pulse shaping [8] has been used to reduce this error.”
MethodA wide dynamic range receiver channel for a pulsed time-of-flight laser radar
Ruotsalainen, T., Palojärvi, P., & Kostamovaara, J. (2001) · IEEE Journal of Solid-State Circuits · doi:10.1109/4.938373 · Cited by 93 · cited 1×
“In [9], another technique using automatic gain control has been proposed to minimize the error; however, the receiver bandwidth of 170 MHz and dynamic range of 1:624 are not adequate to our purpose.”
MethodPalojärvi, P., Ruotsalainen, T., & Kostamovaara, J. (2005) · IEEE Journal of Solid-State Circuits · doi:10.1109/jssc.2005.848022 · Cited by 78 · cited 2×
“Namely, pulse length [4], amplitude [6], slew rate [7], or unipolar-to-bipolar pulse shaping [8] has been used to reduce this error.”
BackgroundMethodA CMOS optical preamplifier for wireless infrared communications
Phang, K., & Johns, D. A. (1999) · IEEE Transactions on Circuits and Systems II Analog and Digital Signal Processing · doi:10.1109/82.775380 · Cited by 75
Research works printed but not linked: 1
- 1991, A Family of Wideband Low Noise Transimpedance Amplifiers
Cited by
A High-Sensitivity and Low-Walk Error LADAR Receiver for Military Application
Cho, H.-S., Kim, C.-H., & Lee, S.-G. (2014) · IEEE Transactions on Circuits and Systems I: Regular Papers · doi:10.1109/tcsi.2014.2327282 · Cited by 88
“In the design, a three-stage inverting amplifier [2] is adopted for the TIA, rather than a common source or cascode amplifiers, which has high DC gain of about 80 dB with GBW of about 6.”
BackgroundMethodSelf-citationA Wide Dynamic Range CMOS Laser Radar Receiver With a Time-Domain Walk Error Compensation Scheme
Kurtti, S., Nissinen, J., & Kostamovaara, J. (2017) · IEEE Transactions on Circuits and Systems I: Regular Papers · doi:10.1109/tcsi.2016.2619762 · Cited by 66
“The performance of the proposed receiver is summarized and compared with figures presented in other recently published works in this field in Table I [13], [28]–[31].”
A Low Walk Error Analog Front-End Circuit With Intensity Compensation for Direct ToF LiDAR
Wang, X., Ma, R., Li, D., Zheng, H., Liu, M., & Zhu, Z. (2020) · IEEE Transactions on Circuits and Systems I: Regular Papers · doi:10.1109/tcsi.2020.3022714 · Cited by 64
“It can be concluded from (9) that the input-referred noise current is slightly decreased in this design, compared with the conventional topology [16].”
BackgroundMethodResultInfluentialA CMOS Receiver–TDC Chip Set for Accurate Pulsed TOF Laser Ranging
Kurtti, S., Jansson, J.-P., & Kostamovaara, J. (2020) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2019.2918372 · Cited by 64
“This work [14] [23] [24] [25] [26] [27]”
A Linear-Mode LiDAR Sensor Using a Multi-Channel CMOS Transimpedance Amplifier Array
Hong, C., Kim, S.-H., Kim, J.-H., & Park, S. M. (2018) · IEEE Sensors Journal · doi:10.1109/jsen.2018.2852794 · Cited by 64
“They utilize laser light signals to characterize targets effectively across a scene by detecting and processing the reflected signals from targets [1]–[3].”
BackgroundA 60-m range 6.16-mW laser-power linear-mode LiDAR system with multiplex ADC/TDC in 65-nm CMOS
Liu, M., Liu, H., Li, X., & Zhu, Z. (2020) · IEEE Transactions on Circuits and Systems I: Regular Papers · doi:10.1109/tcsi.2019.2955671 · Cited by 54
“The inverter (INV) TIAs in [9], [13] with large power consumption showed a better”
BackgroundMethodA Linear Dynamic Range Receiver with Timing Discrimination for Pulsed TOF Imaging LADAR Application
Zheng, H., Ma, R., Liu, M., & Zhu, Z. (2018) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2018.2826860 · Cited by 46
“To preserve the edges of pulsed echo, the optimum relationship between BW and the rise time (tr ) of the processed pulsed signal is approximately expressed as follows [8]:”
InfluentialA 66-dB Linear Dynamic Range, 100-dB·$\Omega$ Transimpedance Gain TIA With High-Speed PDSH for LiDAR
Ma, R., Liu, M., Zheng, H., & Zhu, Z. (2019) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2019.2907776 · Cited by 45
A 77-dB Dynamic Range Low-Power Variable-Gain Transimpedance Amplifier for Linear LADAR
Ma, R., Liu, M., Zheng, H., & Zhu, Z. (2018) · IEEE Transactions on Circuits and Systems II: Express Briefs · doi:10.1109/tcsii.2017.2684822 · Cited by 42
“Compared to [1], the proposed TIA achieved a lower input impedance, higher gain, TABLE II PERFORMANCE COMPARISONS OF RECENTLY PUBLISHED”
BackgroundMethodResultInfluentialZheng, H., Ma, R., Liu, M., & Zhu, Z. (2018) · IEEE Sensors Journal · doi:10.1109/jsen.2018.2809795 · Cited by 40
“(9) with respect to CGS,MN1 and setting the result to zero [10].”
BackgroundResultInfluentialA Wide Dynamic Range Laser Radar Receiver Based on Input Pulse-Shaping Techniques
Baharmast, A., Kurtti, S., & Kostamovaara, J. (2020) · IEEE Transactions on Circuits and Systems I Regular Papers · doi:10.1109/tcsi.2020.2983834 · Cited by 34
“is to employ electronic gain control, either within the input stage or as a separate block [1], [25], [27], [30], [31].”
BackgroundMethodInfluentialA Transimpedance-to-Noise Optimized Analog Front-End With High PSRR for Pulsed ToF Lidar Receivers
Khoeini, F., Hadidian, B., Zhang, K., & Afshari, E. (2021) · IEEE Transactions on Circuits and Systems I Regular Papers · doi:10.1109/tcsi.2021.3089098 · Cited by 32
Experimental Investigation Into Laser Ranging With Sub-ns Laser Pulses
Hintikka, M., & Kostamovaara, J. (2017) · IEEE Sensors Journal · doi:10.1109/jsen.2017.2777501 · Cited by 28
Mirrored Current-Conveyor Transimpedance Amplifier for Home Monitoring LiDAR Sensors
Yoon, D., Joo, J.-E., & Park, S. M. (2021) · IEEE Sensors Journal · doi:10.1109/jsen.2020.3043797 · Cited by 23
“Meanwhile, AGC function should be employed to vary the feedback resistance which corresponds to transimpedance gain, thus enabling wide input dynamic range of incoming photocurrents [10]–[14].”
BackgroundA Linear-Array Receiver Analog Front-End Circuit for Rotating Scanner LiDAR Application
Zheng, H., Ma, R., Liu, M., & Zhu, Z. (2019) · IEEE Sensors Journal · doi:10.1109/jsen.2019.2905267 · Cited by 23
“Secondly, compared with the single channel works [8], [17], the proposed TIA shows the some advantages, which include lower noise and power dissipation performance.”
BackgroundInfluentialWang, X., Ma, R., Li, D., Hu, J., & Zhu, Z. (2022) · IEEE Transactions on Circuits & Systems II Express Briefs · doi:10.1109/tcsii.2022.3220888 · Cited by 22
“Substituting (6) into (5), the noise optimization derivation is based on [2] and it comes to the conclusion that the noise performance can be optimized by making Cgs,FF being between CP/2 and CP+ Cgs1.”
BackgroundMethodJoo, J.-E., Lee, M.-J., & Park, S. M. (2021) · Sensors · doi:10.3390/s21134364 · Cited by 20
“Parameters This Work [6] [12] [13] [14] [15]”
Zheng, H., Ma, R., Wang, X., Li, D., Hu, J., Liu, Y., & Zhu, Z. (2022) · IEEE Transactions on Circuits and Systems I Regular Papers · doi:10.1109/tcsi.2022.3204639 · Cited by 21
“2D/3D range imaging applications, there are typically three types of receivers used in pulsed dToF LiDAR systems: single pixel receiver with two-dimension scanning system [8], linear-”
BackgroundMethodA CMOS Fully Differential Optoelectronic Receiver for Short-Range LiDAR Sensors
Joo, J.-E., Lee, M.-J., & Park, S. M. (2023) · IEEE Sensors Journal · doi:10.1109/jsen.2023.3236678 · Cited by 19
“vers have been suggested [6], [7], [8], [9], [10], [11], [12],”
A Low-Noise and Wide Dynamic Range 15 MHz CMOS Receiver for Pulsed Time-of-Flight Laser Ranging
Kurtti, S., Baharmast, A., Jansson, J.-P., & Kostamovaara, J. (2021) · IEEE Sensors Journal · doi:10.1109/jsen.2021.3105447 · Cited by 19
A Multi-Channel Low-Noise Analog Front End Circuit for Linear LADAR
Wang, P., Ye, M., Xia, X., Zheng, X., Li, Y., & Zhao, Y. (2019) · IEEE Transactions on Circuits & Systems II Express Briefs · doi:10.1109/tcsii.2019.2937352 · Cited by 16
“In contrast to designs [6] and [10], the proposed circuit”
ResultA CMOS AFE With 37-nA rms Input-Referred Noise and Marked 96-dB Timing DR for Pulsed LiDAR
Li, K., Guo, J., & Zhao, Y. (2022) · IEEE Transactions on Circuits and Systems I: Regular Papers · doi:10.1109/tcsi.2022.3181133 · Cited by 14
“12 presents the test setup for the frequency response of the AFE, where a vector network analyzer (VNA) (Keysight E5063A) was used to provide the frequency-swept voltage source and S21 measurement, while a resistor in series with a voltage source was adopted to emulate a current source [7], [8], [31] and [36].”
MethodDesign of a CMOS ROIC for InGaAs Self-Mixing Detectors Used in FM/cw LADAR
Hu, K., Zhao, Y., Ye, M., Gao, J., Zhao, G., & Zhou, G. (2017) · IEEE Sensors Journal · doi:10.1109/jsen.2017.2724064 · Cited by 14
“due to the needs of wideband receivers [1], the good pixel uniformity for FPA detectors, etc.”
BackgroundA CMOS AFE Array With DC Input Current Cancellation for FMCW LiDAR
Zheng, X., Ye, M., Li, Z., Li, Y., Wang, Q., & Zhao, Y. (2024) · IEEE Transactions on Very Large Scale Integration (VLSI) Systems · doi:10.1109/tvlsi.2024.3350870 · Cited by 11
“The authors [4], [10], [27], [29] were designed for single channel.”
BackgroundMethodTransimpedance amplifier with a compression stage for wide dynamic range optical applications
Atef, M. (2015) · Microelectronics Journal · doi:10.1016/j.mejo.2015.04.004 · Cited by 11
Zou, C., Ou, Y., Zhu, Y., Martins, R. P., Chan, C., & Zhang, M. (2024) · IEEE Journal of Solid-State Circuits · doi:10.1109/jssc.2024.3440475 · Cited by 9
“Equations (2) and (3) show a clear design conflict between transimpedance gain and bandwidth through R f [20].”
BackgroundA linear and wide dynamic range transimpedance amplifier with adaptive gain control technique
Zheng, H., Ma, R., & Zhu, Z. (2016) · Analog Integrated Circuits and Signal Processing · doi:10.1007/s10470-016-0867-1 · Cited by 9
A Low Noise, Wide Dynamic Range TOF Laser Radar Receiver Based on Pulse Shaping Techniques
Baharmast, A., Ruotsalainen, T., & Kostamovaara, J. (2018) · IEEE International Symposium on Circuits and Systems proceedings · doi:10.1109/iscas.2018.8351606 · Cited by 8
“Various techniques have been proposed for implementing a TOF receiver, and the state-of-the-art solutions include compensated leading edge detection ([7-9]), linear range detection (using gain control, [3, 10]) and unipolar-to-bipolar conversion ([11, 12]).”
MethodRehman, M. R. U., Hejazi, A., Ali, İ., Lee, J. J., Oh, S.-J., Pu, Y., & Lee, K. (2020) · IEEE Access · doi:10.1109/access.2020.2982180 · Cited by 8
A 700 MHz laser radar receiver realized in 0.18 μm HV-CMOS
Hintikka, M., & Kostamovaara, J. (2017) · Analog Integrated Circuits and Signal Processing · doi:10.1007/s10470-017-1041-0 · Cited by 8
A Low-Complexity Hybrid Readout Circuit for Lidar Receiver
Ye, M., Zheng, X., Li, Y., & Zhao, Y. (2019) · IEEE Transactions on Very Large Scale Integration (VLSI) Systems · doi:10.1109/tvlsi.2019.2947159 · Cited by 8
“In order to achieve the transimpedance gain as high as 100 dB , cascaded voltage amplifiers are often adopted [12], [13].”
BackgroundHintikka, M., Hallman, L. W., & Kostamovaara, J. (2017) · Review of Scientific Instruments · doi:10.1063/1.4999253 · Cited by 7
Gorre, P., Vignesh, R., & Kumar, S. S. (2022) · Microelectronics Journal · doi:10.1016/j.mejo.2022.105477 · Cited by 7
A CMOS chip set for accurate pulsed time-of-flight laser range finding
Kurtti, S., Nissinen, J., Jansson, J.-P., & Kostamovaara, J. (2018) · IEEE International Instrumentation and Measurement Technology Conference · doi:10.1109/i2mtc.2018.8409646 · Cited by 7
Design of Differential Variable-Gain Transimpedance Amplifier in 0.18 µm SiGe BiCMOS
Lee, S. B. S., Liu, H., Yeo, K. S., Chen, J., & Yu, X. (2020) · Electronics · doi:10.3390/electronics9071058 · Cited by 7
Lee, S. B. S., & Yeo, K. S. (2021) · Electronics · doi:10.3390/electronics10233042 · Cited by 6
“The designs in [13,15,16] only have either a CG, CS or inverter-type input stage, making it difficult to balance the gain-bandwidth trade-off.”
Jinqing, Y., Gu, G., Qian, W., Ren, K., Lu, D., Zhang, J., Guo, P., Gao, Q., Wan, M., & Chen, Q. (2020) · Optics Express · doi:10.1364/oe.398313 · Cited by 6
The Design of Clocked-Comparator-Based Time-Interval Measurement Circuit for Pulse ToF Measurement
Jaya, G. L., Chen, S., & Siek, L. (2017) · IEEE Sensors Journal · doi:10.1109/jsen.2017.2749417 · Cited by 6
“Rangefinders that utilize a pulse-shaped wave are typically used for range measurements that require a relatively simple wave generation and echo processing, a high precision result, a high speed acquisition, and the capability to deal with echoes which may vary greatly in strength and which may come from multiple obj…”
BackgroundA Low-Power Multimode Eight-Channel AFE for dToF LiDAR
Yang, Y., Liu, X., Yang, R., Ma, S., Xia, Y., Li, J., Zhang, B., Geng, L., & Li, D. (2024) · 2024 IEEE International Symposium on Circuits and Systems (ISCAS) · doi:10.1109/iscas58744.2024.10557862 · Cited by 5
“C1 and C2 are filtering capacitors [8].”
A High-Multi Target Resolution Focal Plane Array-Based Laser Detection and Ranging Sensor
Kim, H., Lee, E., & Kim, C. (2019) · Sensors · doi:10.3390/s19051210 · Cited by 5
“An excessive photo current can increase the input voltage of the TIA beyond the breakdown voltage [8].”
BackgroundMethodResultInfluentialSelf-citationSędek, B., Zygmunt, M., Jakubaszek, M., Drozd, T., & Wojtanowski, J. (2024) · Sensors · doi:10.3390/s24030733 · Cited by 5
“Equation (6) [5]: The impact of the SNR on distance measurement precision can be represented by Equation (6) [5]: where t r is the rise time of the laser pulse, c is the speed of light, and SNR is the signal-to-noise ratio.”
BackgroundIntegrated Circuits/Microchips
Yeap, K. H., & Hoyos, J. J. S. (2020) · IntechOpen eBooks · doi:10.5772/intechopen.83313 · Cited by 8
Baharmast, A., & Kostamovaara, J. (2020) · Optical Engineering · doi:10.1117/1.oe.59.10.104102 · Cited by 5
“One successful way to tackle this issue is to sample the echo signals continuously and convert them to digital data using an analog-to-digital converter (ADC).(23,24) In this way, walk error-free time positions of the reflected echoes can be acquired.”
MethodAn On-Chip AC Coupled AFE With Asymmetric Output Stage for d-ToF LiDAR
Yang, Y., Feng, H., Yin, Z., Ma, S., Li, J., Shan, X., Xia, Y., Yang, R., Zhang, B., Geng, L., et al. (2024) · IEEE Transactions on Circuits & Systems II Express Briefs · doi:10.1109/tcsii.2024.3489640 · Cited by 4
“Among the various types of detectors, receivers widely rely on linear-mode avalanche photodiodes (APD) for their high sensitivity and the ability to provide intensity information [3].”
Wideband Receiver Module for LADAR Using Large Area InGaAs Avalanche Photodiode
Park, C.-Y., Kim, D.-B., Kim, C.-H., Kwon, Y., Kang, E.-C., Lee, C., Choi, S., La, J., & Ko, J. S. (2013) · 한국광학회지 · doi:10.3807/kjop.2013.24.1.001 · Cited by 4
“0 pF 일 때, TIA에 의 한 잡음전류는 설계치(Ideal)가 73 nA, 온도 및 non-ideality 를 고려한 최대잡음은 145 nA(worst case), 평균 115 nA를 갖도록 설계하였다.([8]) 식 (1)의 APD에 의한 잡음은 광전류, 암전류 및 증폭에 의한 Shot noise에 해당하며, Excess noise factor, F(M), 가 곱해진 값으로 주어진다.”
InfluentialSelf-citationZheng, H., Ma, R., & Zhu, Z. (2017) · Microelectronics Journal · doi:10.1016/j.mejo.2017.03.001 · Cited by 4
“In order to make the receiver achieve a high linearity with the input pulsed current of the echo signal, the scheme [15,16] of external analog voltage control is applied to control the transimpedance gain in the transimpedance amplifier (TIA), however, it brings difficulties for the system design, and does not adequat…”
BackgroundChon, Y., Choi, S., & Park, S.-M. (2024) · Photonics · doi:10.3390/photonics11100974 · Cited by 3
“[21] demonstrated a dual-mode AFE preamplifier which could be configured as a charge-sensitive amplifier (CSA) or as a gated active load-assisted (GALA) TIA, depending upon the intensity of the input current, thereby extending the dynamic range to 96dB.”
BackgroundA high sensitive 66 dB linear dynamic range receiver for 3-D laser radar
Ma, R., Zheng, H., & Zhu, Z. (2017) · Journal of Semiconductors · doi:10.1088/1674-4926/38/8/085006 · Cited by 3
Modeling, Prediction, and Results Correction of PDSH Circuits for Nanosecond Pulse Peak Detection
Shu, J., Du, Y., Zhao, H. L., Liu, K., & Qiu, J. (2023) · Applied Sciences · doi:10.3390/app132312597 · Cited by 3
A 35 MHz CMOS Receiver for 3 ns Laser Pulses in Pulsed TOF Laser Ranging
Kostamovaara, J., Kurtti, S., & Ruotsalainen, T. (2025) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2025.3569943 · Cited by 2
“The recent literature on linear receivers developed for pulsed time-of-flight laser radars focuses mainly on the development of low noise transimpedance amplifiers with a relatively high bandwidth (BW) of 100 MHz ... 300 MHz [7], [19], [20], [21], [22], [23], [24], [25].”
Zheng, H., Ma, R., Wang, X., Li, D., Hu, J., & Yang, D. (2025) · Microelectronics Journal · doi:10.1016/j.mejo.2025.106845 · Cited by 2
Three-Channel CMOS Transimpedance Amplifier for LiDAR Sensor Receiver
Liu, R., Zhu, J., Jiang, Y. L., Li, F., Jiang, C., & Meng, Z. (2023) · Journal of Systems Engineering and Electronics · doi:10.23919/jsee.2023.000058 · Cited by 2
An 8 × 8 CMOS Optoelectronic Readout Array of Short-Range LiDAR Sensors
Chon, Y., Choi, S., Joo, J., & Park, S. M. (2024) · Sensors · doi:10.3390/s24206686 · Cited by 2
Time Expansion of Pulse Echo Signal Implemented for Laser Ranging System With High Precision
Tu, Y., Li, J., Ruan, H., Deng, Y., Li, L., He, S., & Guo, D. (2024) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2024.3500055 · Cited by 2
Lee, E., Lee, J.-E., Song, M., Choi, G. D., Mheen, B., Jung, B. C., & Kim, C. (2018) · Analog Integrated Circuits and Signal Processing · doi:10.1007/s10470-018-1112-x · Cited by 2
“Table 3 Summary of 4-to-1 TICA performances Parameter This work [8] [21] [24] [25]*”
BackgroundSelf-citationLee, E., Lee, J.-E., Jung, B. C., Mheen, B., & Kim, C. (2017) · Applied Sciences · doi:10.3390/app7070689 · Cited by 1
“The OCP circuit, as shown in Figure 6, is designed to protect the 4-to-1 TCA from being damaged by a very high input current [16].”
BackgroundSelf-citationRobust Multi-Event Detection for Pulsed LiDARs
Kwak, S. S., Lee, J., Im, Y. C., Lee, H. G., & Kim, Y. S. (2024) · IEEE Access · doi:10.1109/access.2024.3412242 · Cited by 1
“3 shows a conventional nonlinear 3-stage inverter-based TIA for high gain, high bandwidth, low noise, and low power consumption [15], [16], [17].”
BackgroundLin, Y., Lin, Q., Chen, Q., Li, J., & Luo, Z. (2026) · Preprints.org · doi:10.20944/preprints202601.1573.v1
“As autonomous driving technology advances to Level 4 (L4) and higher grades, the detection accuracy, anti-interference capability, and real-time response performance of vehicle-mounted LiDAR (as a core sensor for environmental perception) directly determine driving safety [1–3].”
A Micromachined Millimeter-Wave Radar Technology for Indoor Navigation
Moallem, M. (2014) · Deep Blue (University of Michigan)
Hong, C., & Park, S. M. (2016) · The Transactions of The Korean Institute of Electrical Engineers · doi:10.5370/kiee.2016.65.5.831
Development of Near-IR and Beam Shaping of Mid-IR Lasers
Maweza, L. (2019) · SUNScholar (Stellenbosch University)
Kim, H., Lee, E., Choi, H., & Kim, C. (2019) · Applied Sciences · doi:10.3390/app9102145
“It has 16 copies of TIAs as current input buffers, and a TIA has the regulated cascode (RGC) topology based on the inverter local feedback for a low-input impedance [15].”
MethodSelf-citationCMOS Integrated Circuits for Various Optical Applications
Park, S. M. (2020) · IntechOpen eBooks · doi:10.5772/intechopen.92014 · Cited by 1
A Microstrip Strip Line Based High Dynamic range Optical Front-end for LiDAR Application
Gorre, P., Samantaray, A. K., M, S. K. K., & Shaik, B. R. (2023) · International Conference on Artificial Intelligence and Signal Processing (AISP) · doi:10.1109/aisp57993.2023.10134997
45-nm CMOS Inverter Transimpedance Amplifier for LiDAR Applications
Süleyman, E. (2024) · Brilliant Engineering · doi:10.36937/ben.2024.4915
Hao, 郑. Z., Yanming, 何. H., Xiaonan, 郭. G., Dongdong, 杨. Y., & Yanfei, 刘. L. (2025) · Laser & Optoelectronics Progress · doi:10.3788/lop242466
Kostamovaara, J., Jahromi, S., & Huikari, J. (2026) · IEEE photonics journal · doi:10.1109/jphot.2026.3665599
“A lidar using a linear mode optical detector requires, however, high-performance receiver electronics, which should amplify the detector response with maximum sensitivity for further signal processing in a wide dynamic range of echo amplitudes [7], [8], [9], [10], [11], [12], [13], [14], [15].”
Wang, X., Wang, Z., Zheng, H., Li, D., Hu, J., Ma, R., & Zhu, Z. (2026) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2026.3671935
“10 [37].”
문찬희, Gim, J. R., & Lim, H. (2026) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2026.3712932
“To prevent signal saturation, a gain control scheme was employed [32], [33], [34], which reduced the input-amplitude variations and resulting time walk, but its dynamic range was still limited to 1:600–2000.”
Metadata
- Authors
- Ngo, T.-H., Kim, C.-H., Kwon, Y. J., Ko, J. S., Kim, D.-B., & Park, H.-H.
- Affiliations
- Korea Advanced Institute of Science and Technology (KR)
- Agency for Defense Development (KR)
- Samsung (South Korea) (KR)
- Venue
- IEEE Transactions on Circuits and Systems I: Regular Papers
- Published
- 2013-02
- Volume
- 60
- Issue
- 2
- Pages
- 448-456
- ISSN
- 1549-8328 (ISSN-L)
- 1558-0806
- OpenAlex
- W2069474418
- Cited by
- 68
- References
- 21
- Citations by year
- 2026: 3 · 2025: 3 · 2024: 10 · 2023: 4 · 2022: 4 · 2021: 4 · 2020: 9 · 2019: 9 · 2018: 6 · 2017: 9 · 2016: 3 · 2015: 1 · 2014: 2 · 2013: 1
- FWCI
- 2.94
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- IEEE Transactions on Circuits and Systems I Regular Papers (publishedVersion)
- Topics
- Physical Sciences › Physics and Astronomy › Instrumentation › Advanced Optical Sensing Technologies
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Radio Frequency Integrated Circuit Design
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Analog and Mixed-Signal Circuit Design
- Keywords
- wideband receiver, direct detection, CMOS integrated circuit, linear dynamic range, gain control, noise minimization, signal-to-noise ratio, frequency response compensation, temperature stability, pulsed laser ranging
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.