Accurate Power Loss Model Derivation of a High-Current Dual Active Bridge Converter for an Automotive Application
The DOI matches its Crossref record; 25 of the 26 references it cites were found in a registry or an index.
Abstract
An accurate power loss model for a high-efficiency dual active bridge converter, which provides a bidirectional electrical interface between a 12-V battery and a high-voltage (HV) dc bus in a fuel cell car, is derived. The nominal power is 2 kW, the HV dc bus varies between 240 and 450 V, and the battery voltage range is between 11 and 16 V. Consequently, battery currents of up to 200 A occur at nominal power. In automotive applications, high converter efficiency and high power densities are required. Thus, it is necessary to accurately predict the dissipated power for each power component in order to identify and to properly design the heavily loaded parts of the converter. In combination with measured efficiency values, it is shown that conventional converter analysis predicts substantially inaccurate efficiencies for the given converter. This paper describes the main reasons why the conventional method fails and documents the different steps required to predict the power losses more accurately. With the presented converter prototype, an efficiency of more than 92% is achieved at an output power of 2 kW in a wide input/output voltage range.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Citations
Cites
A three-phase soft-switched high-power-density DC/DC converter for high-power applications
De Doncker, R. W. A. A., Divan, D. M., & Kheraluwala, M. H. (1991) · IEEE Transactions on Industry Applications · doi:10.1109/28.67533 · Cited by 2,535 · cited 1×
“Optimized modulation methods [12] or circuit variants—such as the three phase DAB [13]—enable a more effective converter utilization in order to reduce circulating currents and to obtain”
BackgroundEmadi, A., Lee, Y. J., & Rajashekara, K. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.922768 · Cited by 1,461 · cited 2×
“architecture, the electric power demand exceeds 10 kW [1], and”
BackgroundBai, H., & Mi, C. (2008) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2008.2005103 · Cited by 1,121 · cited 1×
“currents and switching losses are reduced [12], [24].”
BackgroundEnergy Storage Systems for Automotive Applications
Lukic, S. M., Cao, J., Bansal, R. C., Rodriguez, F., & Emadi, A. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.918390 · Cited by 1,025 · cited 1×
“and ultracapacitors for high peak power [2], provide the electric power.”
BackgroundEmadi, A., Williamson, S. S., & Khaligh, A. (2006) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2006.872378 · Cited by 714 · cited 1×
“Currently, the electric system in a conventional car consists of a 14-V dc power system architecture that comprises of a 12-V battery, starter motor, battery charger, and all the vehicular loads such as lighting and radio [4].”
BackgroundCalculation of losses in ferro- and ferrimagnetic materials based on the modified Steinmetz equation
Reinert, J., Brockmeyer, A., & De Doncker, R. W. A. A. (2001) · IEEE Transactions on Industry Applications · doi:10.1109/28.936396 · Cited by 704
Inoue, S., & Akagi, H. (2007) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2006.889939 · Cited by 669 · cited 1×
“On the assumption of negligible conduction losses and a negligible transformer magnetizing current (which is sufficiently fulfilled for higher power levels), these considerations lead to the most simple lossless electrical DAB model [Fig. 2(b)] [ 19 ].”
Optimal choice for number of strands in a litz-wire transformer winding
Sullivan, C. R. (1999) · IEEE Transactions on Power Electronics · doi:10.1109/63.750181 · Cited by 558
Calculation of losses in ferro- and ferrimagnetic materials based on the modified Steinmetz equation
Reinert, J., Brockmeyer, A., & De Doncker, R. W. (2003) · Conference Record of the 1999 IEEE Industry Applications Conference. Thirty-Forth IAS Annual Meeting (Cat. No.99CH36370) · doi:10.1109/ias.1999.806023 · Cited by 409 · cited 2×
“, the modified Steinmetz equation [20], finite element analysis or the use of measurement results [21], is required.”
BackgroundMethodZhu, L. (2006) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2005.869730 · Cited by 381 · cited 1×
“Among the most prominent converter candidates are the isolated boost, full bridge converter [10], and the L-type (or current doubler) converter [11] due to their suitability for high-frequency operation and due to the similarities to the well-known buck and boost converters.”
BackgroundEnergy Management Power Converters in Hybrid Electric and Fuel Cell Vehicles
Lai, J.-S., & Nelson, D. J. (2007) · Proceedings of the IEEE · doi:10.1109/jproc.2006.890122 · Cited by 318 · cited 1×
“The HV ratio between V1 and V2 as well as the high automotive safety standards demand galvanic isolation [6], [7].”
BackgroundA ZVS Bidirectional DC–DC Converter With Phase-Shift Plus PWM Control Scheme
Xiao, H., & Xie, S. (2008) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2007.915188 · Cited by 299 · cited 1×
“Among the most prominent converter candidates are the isolated boost, full bridge converter [10], and the L-type (or current doubler) converter [ 11 ] due to their suitability for high-frequency operation and due to the similarities to the well-known buck and boost converters.”
BackgroundPerformance optimization of a high current dual active bridge with a wide operating voltage range
Krismer, F., Round, S., & Kolar, J. W. (2006) · 2006 37th IEEE Power Electronics Specialists Conference · doi:10.1109/pesc.2006.1712096 · Cited by 276 · cited 4×
“, using advanced modulation methods [12] or additional circuitry [22], [23]).”
BackgroundMethodInfluentialSelf-citationMultiphase Bidirectional Flyback Converter Topology for Hybrid Electric Vehicles
Bhattacharya, T., Giri, V. S., Mathew, K., & Umanand, L. (2009) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.2004661 · Cited by 177 · cited 1×
“propulsion power and to facilitate the energy transfer between different dc voltage levels [3].”
BackgroundA New Family of Full-Bridge ZVS Converters
Jang, Y., & Jovanovic, M. M. (2004) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2004.826493 · Cited by 164 · cited 1×
“, using advanced modulation methods [12] or additional circuitry [22], [23]).”
MethodFault Diagnosis of a ZVS DC–DC Converter Based on DC-Link Current Pulse Shapes
Kim, S. Y., Nam, K., Song, H.-S., & Kim, H.-G. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2007.910627 · Cited by 93 · cited 1×
“In addition, a high converter efficiency (more than 90%), high reliability, and high power density are required [8]; this is typically achieved with soft switching techniques that result in low switching losses, and consequently, a high switching frequency can be employed [9].”
BackgroundTemperatures Evaluation in an Integrated Motor Drive for Traction Applications
Tenconi, A., Profumo, F., Bauer, S. E., & Hennen, M. D. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.2003099 · Cited by 73 · cited 1×
“In a next step, the discussed model can be extended with a coupled electrothermal converter model that includes the influence of raised component temperatures on the efficiency in order to accurately calculate the expected component temperatures [16], [17].”
BackgroundA Practical Transformer Core Loss Measurement Scheme for High-Frequency Power Converter
Han, Y., & Liu, Y. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2007.896154 · Cited by 71 · cited 1×
“, the modified Steinmetz equation [20], finite element analysis or the use of measurement results [21], is required.”
BackgroundBi-directional DC/DC Converter for Hybrid Vehicles
García, O., Flores, L. A., Oliver, J. A., Cobos, J. A., & de la Pena, J. (2006) · IEEE Power Electronics Specialists Conference (PESC) · doi:10.1109/pesc.2005.1581888 · Cited by 62 · cited 1×
“total converter efficiency for the full operating range [15].”
BackgroundA Coupled Electrothermal Model for Planar Transformer Temperature Distribution Computation
Buccella, C., Cecati, C., & de Monte, F. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.2003102 · Cited by 60 · cited 2×
“In a next step, the discussed model can be extended with a coupled electrothermal converter model that includes the influence of raised component temperatures on the efficiency in order to accurately calculate the expected component temperatures [16], [17].”
BackgroundA novel low-loss modulation strategy for high-power bi-directional buck+boost converters
Waffler, S., & Kolar, J. W. (2007) · doi:10.1109/icpe.2007.4692513 · Cited by 54
Self-citationCoupled-Filter-Inductor Soft-Switching Techniques: Principles and Topologies
Russi, J. L., Martins, M. L. D. S., & Hey, H. L. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.927983 · Cited by 54 · cited 1×
“, using advanced modulation methods [12] or additional circuitry [22], [23]).”
MethodDC-to-DC converters for electric and hybrid vehicles
Khan, I. A. (2002) · IEEE Workshop on Power Electronics in Transportation · doi:10.1109/pet.1994.572366 · Cited by 23 · cited 1×
“The HV ratio between V1 and V2 as well as the high automotive safety standards demand galvanic isolation [6], [7].”
BackgroundLee, S.-S., & Moon, G. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.921239 · Cited by 18 · cited 1×
“In addition, a high converter efficiency (more than 90%), high reliability, and high power density are required [8]; this is typically achieved with soft switching techniques that result in low switching losses, and consequently, a high switching frequency can be employed [9].”
BackgroundIsurin, A., & Cook, A. B. (2006) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec.2006.1620517 · Cited by 6 · cited 1×
“For converter topologies without large dc inductors, further efficiency improvements are attained with resonant dc–dc converter topologies [14].”
Background
Research works printed but not linked: 1
- laeuffer, 2001, automotive requirements for power electronic converters in traction advanced control systems, Proc Int Intell Motion Conf, 207
Cited by
Zhao, B., Song, Q., Liu, W., & Sun, Y. (2014) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2013.2289913 · Cited by 1,886
“A power loss model of LV and high-current DAB-IBDC for automotive applications was analyzed in [98].”
MethodEfficiency-Optimized High-Current Dual Active Bridge Converter for Automotive Applications
Krismer, F., & Kolar, J. W. (2012) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2011.2112312 · Cited by 747
Self-citationClosed Form Solution for Minimum Conduction Loss Modulation of DAB Converters
Krismer, F., & Kolar, J. W. (2012) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2011.2157976 · Cited by 635
“This DAB is realized for an automotive application and enables bidirectional power transfer between the HV power train and the LV dc bus (LV battery, LV ancillary loads) of a fuel cell car [1], [4].”
BackgroundSelf-citationGeneralized Average Modeling of Dual Active Bridge DC–DC Converter
Qin, H., & Kimball, J. W. (2012) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2011.2165734 · Cited by 557
“It is an isolated, bidirectional, buck and boost dc–dc converter topology, which can be used in high-power applications for solid-state transformers [2], [3], smart grids [4], electric/hybrid vehicles [5], as well as interface among three dc ports [6].”
BackgroundHou, N., & Li, Y. W. (2020) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2019.2927930 · Cited by 553
“Then, based on different power-loss elements [18], [60], the corresponding power-loss model can be obtained.”
BackgroundMethodInfluential
Metadata
- Authors
- Krismer, F., & Kolar, J. W.
- Affiliations
- ETH Zurich (CH)
- Venue
- IEEE Transactions on Industrial Electronics
- Published
- 2010-03
- Volume
- 57
- Issue
- 3
- Pages
- 881-891
- ISSN
- 0278-0046 (ISSN-L)
- OpenAlex
- W2118203870
- Cited by
- 470
- References
- 26
- Citations by year
- 2026: 21 · 2025: 32 · 2024: 24 · 2023: 24 · 2022: 26 · 2021: 34 · 2020: 29 · 2019: 31 · 2018: 29 · 2017: 40 · 2016: 36 · 2015: 31 · 2014: 35 · 2013: 20 · 2012: 26
- FWCI
- 15.34
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- IEEE Transactions on Industrial Electronics (publishedVersion)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advanced DC-DC Converters
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Multilevel Inverters and Converters
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Wireless Power Transfer Systems
- Keywords
- dual active bridge converter, power loss modeling, bidirectional DC-DC converter, fuel cell vehicles, 12V battery, high-voltage DC bus, power density
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.