The DOI matches its Crossref record; 22 of the 22 references it cites were found in a registry or an index.
Implementation of the Constant Current and Constant Voltage Charge of Inductive Power Transfer Systems With the Double-Sided LCC Compensation Topology for Electric Vehicle Battery Charge Applications
Open accessAbstract
When compared to plugged-in chargers, inductive power transfer (IPT) methods for electric vehicle (EV) battery chargers have several benefits, such as greater convenience and higher safety. In an EV, the battery is an indispensable component, and lithium-ion batteries are identified as the most competitive candidate to be used in EVs due to their high power density, long cycle life, and better safety. In order to charge lithium-ion batteries, constant current/constant voltage (CC/CV) is often adopted for high-efficiency charging and sufficient protection. However, it is not easy to design an IPT battery charger that can charge the batteries with a CC/CV charge due to the wide range of load variations, because it requires a wide range of variation in its operating frequency, duty, or phase-shift. Furthermore, zero phase angle (ZPA) condition for the primary inverter cannot be achieved over the entire charge process without the help of additional switches and related driver circuits to transform the topology. This paper proposes a design method that makes it possible to implement the CC/CV mode charge with minimum frequency variation during the entire charge process by using the load-independent characteristics of an IPT system under the ZPA condition without any additional switches. A theoretical analysis is presented to provide the appropriate procedure to design the double-sided LCC compensation tank which can achieve both CC and CV mode charge under ZPA condition at two different resonant frequencies. As a consequence, the proposed method is advantageous in that the efficiency of compensation tank is very high due to achieving the perfect resonant operation during the entire charge process. A 6.6-kW prototype charger has been implemented to demonstrate the feasibility and validity of the proposed method. A maximum efficiency of 96.1% has been achieved with a 200-mm airgap at 6.6 kW during the CC mode charge.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Fundamentals of Power Electronics
Erickson, R. W., & Maksimović, D. (2001) · Springer eBooks · doi:10.1007/b100747 · Cited by 6,112
Fundamentals of Power Electronics
Erickson, R. W., & Maksimović, D. (2020) · Springer eBooks · doi:10.1007/978-3-030-43881-4 · Cited by 5,420
Wireless Power Transfer for Electric Vehicle Applications
Li, S., & Mi, C. C. (2015) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2014.2319453 · Cited by 2,185
Design Considerations for a Contactless Electric Vehicle Battery Charger
Wang, C.-S., Stielau, O. H., & Covic, G. A. (2005) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2005.855672 · Cited by 1,487
Development of a Single-Sided Flux Magnetic Coupler for Electric Vehicle IPT Charging Systems
Budhia, M., Boys, J. T., Covic, G. A., & Huang, C.-Y. (2013) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2011.2179274 · Cited by 1,273
Wang, C.-S., Covic, G. A., & Stielau, O. H. (2004) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2003.822038 · Cited by 1,213
A Double-Sided LCC Compensation Network and Its Tuning Method for Wireless Power Transfer
Li, S., Li, W., Deng, J., Nguyen, T. D., & Mi, C. C. (2015) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2014.2347006 · Cited by 1,091
Shin, J., Shin, S., Kim, Y., Ahn, S., Lee, S., Jung, G., Jeon, S.-J., & Cho, D.-H. (2014) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2013.2258294 · Cited by 856
A Bidirectional Inductive Power Interface for Electric Vehicles in V2G Systems
Madawala, U. K., & Thrimawithana, D. J. (2011) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2011.2114312 · Cited by 813
A High Efficiency 5 kW Inductive Charger for EVs Using Dual Side Control
Wu, H. H., Gilchrist, A., Sealy, K. D., & Bronson, D. (2012) · IEEE Transactions on Industrial Informatics · doi:10.1109/tii.2012.2192283 · Cited by 512
Cited by
Khalid, M. R., Alam, M. S., Sarwar, A., & Jamil Asghar, M. S. (2019) · eTransportation · doi:10.1016/j.etran.2019.100006 · Cited by 369
Khalid, M. R., Khan, I. A., Hameed, S., Asghar, M. S. J., & Ro, J. (2021) · IEEE Access · doi:10.1109/access.2021.3112189 · Cited by 353
Key challenges for a large-scale development of battery electric vehicles: A comprehensive review
Lebrouhi, B. E., Khattari, Y., Lamrani, B., Maaroufi, M., Zeraouli, Y., & Kousksou, T. (2021) · Journal of Energy Storage · doi:10.1016/j.est.2021.103273 · Cited by 276
A Critical Review on Charging Technologies of Electric Vehicles
Shahjalal, M., Shams, T., Tasnim, M. N., Ahmed, M. R., Ahsan, M., & Haider, J. (2022) · Energies · doi:10.3390/en15218239 · Cited by 66
Muttaqi, K. M., Isac, E., Mandal, A., Sutanto, D., & Akter, S. (2024) · Electric Power Systems Research · doi:10.1016/j.epsr.2023.109899 · Cited by 57
Metadata
- Authors
- Vu, V.-B., Tran, D.-H., & Choi, W.
- Venue
- IEEE Transactions on Power Electronics
- Published
- 2018-09
- Volume
- 33
- Issue
- 9
- Pages
- 7398-7410
- ISSN
- 0885-8993 (ISSN-L)
- 1941-0107
- OpenAlex
- W2765088853
- Cited by
- 450
- References
- 22
- FWCI
- 10.96
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Implementation of the Constant Current and Constant Voltage Charge of Inductive Power Transfer Systems With the Double-Sided LCC Compensation Topology for Electric Vehicle Battery Charge Applications. https://app.cochat.ai/papers/10.1109/tpel.2017.2766605
- The paper
- Vu, V.-B., Tran, D.-H., & Choi, W. (2018). Implementation of the Constant Current and Constant Voltage Charge of Inductive Power Transfer Systems With the Double-Sided LCC Compensation Topology for Electric Vehicle Battery Charge Applications. IEEE Transactions on Power Electronics. https://doi.org/10.1109/tpel.2017.2766605
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.