Health monitoring, fault diagnosis and failure prognosis techniques for Brushless Permanent Magnet Machines
The DOI matches its Crossref record; 59 of the 62 references it cites were found in a registry or an index.
Abstract
Over the past few years, many researchers have been attracted by the challenges of electrical machines' fault diagnosis and condition monitoring, which provide early warnings that could help schedule necessary maintenance to avoid catastrophic consequence. With advancements in the use of rare-earth magnets, Brushless Permanent Magnet Machines are widely used in industry recently, which has led to the development of numerous fault diagnosis techniques. Considerable papers have presented reviews and compared condition monitoring and fault diagnosis methods for induction machines, but none for Brushless Permanent Magnet Machines. To make a difference, this paper presents a comprehensive survey of modern research advancements and state-of-the-art in health monitoring, fault diagnosis and prognosis techniques for Brushless Permanent Magnet Machines. The symptoms of each type of fault and the principles of diagnosis process are also described and discussed.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“To the best authors' knowledge the first review on diagnostics of PM machines (BLDC and PMSM) was published in 2011 [14].”
From Fault Diagnosis and Fault-Tolerant Control of PMSM Drives–State of the Art and Future Challenges (2022) · cites this paper as [14]
Citations
Cites
Condition Monitoring and Fault Diagnosis of Electrical Motors—A Review
Nandi, S., Toliyat, H. A., & Li, X. (2005) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2005.847955 · Cited by 2,382 · cited 2×
“Considerable papers have presented reviews and compared condition monitoring and fault diagnosis methods for induction machines [1]-[4], but none for Brushless Permanent Magnet Machines.”
A review of induction motors signature analysis as a medium for faults detection
El Hachemi Benbouzid, M. (2000) · IEEE Transactions on Industrial Electronics · doi:10.1109/41.873206 · Cited by 1,602
Electric Motor Drivers: Modeling, Analysis, and Control
Krishnan, R. (2001) · Cited by 1,561
Introduction to magnetism and magnetic materials
(2016) · Choice Reviews Online · doi:10.5860/choice.195889 · Cited by 1,518
Neural-network-based motor rolling bearing fault diagnosis
Li, B., Chow, M.-Y., Tipsuwan, Y., & Hung, J. C. (2000) · IEEE Transactions on Industrial Electronics · doi:10.1109/41.873214 · Cited by 797
Parameter Estimation, Condition Monitoring, and Diagnosis of Electrical Machines
Vas, P. (1992) · doi:10.1093/oso/9780198593751.001.0001 · Cited by 711
Report of Large Motor Reliability Survey of Industrial and Commercial Installations, Part I
(1985) · IEEE Transactions on Industry Applications · doi:10.1109/tia.1985.349532 · Cited by 602
Zhu, Z. Q., Howe, D., & Chan, C. C. (2002) · IEEE Transactions on Magnetics · doi:10.1109/20.990112 · Cited by 492 · cited 1×
“Zhu et al. [ 16 ] reported a 2D analytical method to predict magnetic flux density of PMSM under different scenarios.”
MethodStatic-, Dynamic-, and Mixed-Eccentricity Fault Diagnoses in Permanent-Magnet Synchronous Motors
Ebrahimi, B. M., Faiz, J., & Roshtkhari, M. J. (2009) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2009.2029577 · Cited by 386 · cited 1×
“Static eccentricity ratio is defined as [15]”
Basic vibration signal processing for bearing fault detection
McInerny, S. A., & Dai, Y. (2003) · IEEE Transactions on Education · doi:10.1109/te.2002.808234 · Cited by 321 · cited 1×
“It could be caused by 1) Metal fatigue 2) Unbalanced stress 3) Improper installation 4) Corrosion/Contamination These problems could result in vibrations and noise during machine operation, which are usually measured and processed as diagnosis indicators [12].”
A new approach to on-line turn fault detection in AC motors
Kliman, G. B., Premerlani, W. J., Koegl, R. A., & Hoeweler, D. (2002) · IAS '96. Conference Record of the 1996 IEEE Industry Applications Conference Thirty-First IAS Annual Meeting · doi:10.1109/ias.1996.557113 · Cited by 303 · cited 1×
“Negative/zero current [28], negative/zero impedance [29], or negative/zero voltage [30] are utilized as indicators for fault detection.”
Detecting Rotor Faults in Low Power Permanent Magnet Synchronous Machines
le Roux, W., Harley, R. G., & Habetler, T. G. (2007) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2006.886620 · Cited by 274 · cited 1×
“[32] determined the strength of the permanent magnets to”
Prognostics, the real issues involved with predicting life remaining
Engel, S. J., Gilmartin, B. J., Bongort, K., & Hess, A. (2002) · 2000 IEEE Aerospace Conference. Proceedings (Cat. No.00TH8484) · doi:10.1109/aero.2000.877920 · Cited by 263 · cited 2×
“[49] have defined this word as follows:”
Ruiz, J.-R. R., Rosero, J. A., Espinosa, A. G., & Romeral, L. (2009) · IEEE Transactions on Magnetics · doi:10.1109/tmag.2009.2015942 · Cited by 231 · cited 2×
“A fixed length of window will provoke an inconsistent treatment of different current frequencies [20], and changing motor speed makes it harder to determine harmonic orders, therefore STFT has limitation for nonstationary operated machines.”
Application of AI tools in fault diagnosis of electrical machines and drives-an overview
Awadallah, M. A., & Morcos, M. M. (2003) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2003.811739 · Cited by 220 · cited 1×
“Considerable papers have presented reviews and compared condition monitoring and fault diagnosis methods for induction machines [1]-[4], but none for Brushless Permanent Magnet Machines.”
BackgroundKim, U., & Lieu, D. K. (1998) · IEEE Transactions on Magnetics · doi:10.1109/20.703862 · Cited by 189
Liu, X.-Q., Zhang, H.-Y., Liu, J., & Yang, J. (2000) · IEEE Transactions on Industrial Electronics · doi:10.1109/41.873210 · Cited by 180 · cited 3×
“Various ANN structures are approved successful in brushless permanent magnet machine fault diagnosis [31], [34]-[39].”
Fuzzy inference systems implemented on neural architectures for motor fault detection and diagnosis
Altug, S., Chen, M.-Y., & Trussell, H. J. (1999) · IEEE Transactions on Industrial Electronics · doi:10.1109/41.807988 · Cited by 172
Rajagopalan, S., Roux, W. L., Habetler, T. G., & Harley, R. G. (2007) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2007.904183 · Cited by 164 · cited 1×
“It has been observed in [18] that the additional frequencies due to partial demagnetization are as same as dynamic”
Nonstationary Motor Fault Detection Using Recent Quadratic Time–Frequency Representations
Rajagopalan, S., Restrepo, J. A., Aller, J. M., Habetler, T. G., & Harley, R. G. (2008) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2008.921431 · Cited by 161 · cited 1×
“To overcome the tradeoff between time and frequency resolution of STFT, Rajagopalan et al. applied other algorithms such as Windowed Fourier Ridges, Wigner-Ville Distributions, [21], Choi–Williams distribution, Born–Jordan distribution and the Zhao–Atlas–Marks distribution [ 22 ] to improve the readability of the time…”
On the application and design of artificial neural networks for motor fault detection. II
Chow, M., Sharpe, R. N., & Hung, J. C. (1993) · IEEE Transactions on Industrial Electronics · doi:10.1109/41.222640 · Cited by 155
Insulation failure prediction in AC machines using line-neutral voltages
Cash, M. A., Habetler, T. G., & Kliman, G. B. (1998) · IEEE Transactions on Industry Applications · doi:10.1109/28.738983 · Cited by 148 · cited 1×
“Negative/zero current [28], negative/zero impedance [29], or negative/zero voltage [30] are utilized as indicators for fault detection.”
Strangas, E. G., Aviyente, S., & Zaidi, S. S. H. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.2007529 · Cited by 148 · cited 1×
“In [55], [56], prognosis is defined as small transient signal detection.”
Chow, M. (1997) · WORLD SCIENTIFIC eBooks · doi:10.1142/9789812819383 · Cited by 144
Detection of Rotor Faults in Brushless DC Motors Operating Under Nonstationary Conditions
Rajagopalan, S., Aller, J. M., Restrepo, J. A., Habetler, T. G., & Harley, R. G. (2006) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2006.882613 · Cited by 143 · cited 2×
“applied other algorithms such as Windowed Fourier Ridges, Wigner-Ville Distributions, [21], Choi–Williams distribution, Born–Jordan distribution and the Zhao–Atlas–Marks distribution [22] to improve the readability of the time-frequency spectrum.”
MethodRuoho, S., Dlala, E., & Arkkio, A. (2007) · IEEE Transactions on Magnetics · doi:10.1109/tmag.2007.906749 · Cited by 142
Characterization of Noise and Vibration Sources in Interior Permanent-Magnet Brushless DC Motors
Ko, H.-S., & Kim, K.-J. (2004) · IEEE Transactions on Magnetics · doi:10.1109/tmag.2004.832991 · Cited by 139
Kim, U., & Lieu, D. K. (1998) · IEEE Transactions on Magnetics · doi:10.1109/20.703863 · Cited by 127 · cited 1×
“[17] also presented a perturbation method to predict the air gap magnetic flux density distribution to analyze eccentricity faults based on a model in polar coordinated, with and without considering slotting effect, where analytically calculated results were verified by corresponding FEA results.”
MethodOn the application and design of artificial neural networks for motor fault detection. I
Chow, M., Sharpe, R. N., & Hung, J. C. (1993) · IEEE Transactions on Industrial Electronics · doi:10.1109/41.222639 · Cited by 114
Kral, C., Habetler, T. G., & Harley, R. G. (2004) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2004.830762 · Cited by 113 · cited 1×
“If the condition is severe, the Unbalanced Magnetic Pull (UMP) could cause stator and rotor contact [ 14 ].”
An on-line method to detect incipient failure of turn insulation in random-wound motors
Sottile, J., & Kohler, J. L. (1993) · IEEE Transactions on Energy Conversion · doi:10.1109/60.260992 · Cited by 111 · cited 1×
“Negative/zero current [28], negative/zero impedance [29], or negative/zero voltage [30] are utilized as indicators for fault detection.”
Awadallah, M. A., Morcos, M. M., Gopalakrishnan, S., & Nehl, T. W. (2005) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2005.847976 · Cited by 105 · cited 1×
“To make it more adaptive to achieve more accurate solutions under different operation conditions, hybrid neural/fuzzy machine fault detectors are also under research [45]-[48], which take advantage of the learning capability of ANNs to optimize fuzzy sets.”
MethodAutomated Monitoring of Magnet Quality for Permanent-Magnet Synchronous Motors at Standstill
Hong, J., Hyun, D., Lee, S. B., Yoo, J.-Y., & Lee, K.-W. (2010) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2010.2049811 · Cited by 100 · cited 1×
“In reality not only partial demagnetization, but also other asymmetric problems like load unbalance, misalignment, or oscillating load can produce the same harmonics [19].”
Fault diagnosis and condition monitoring of electrical machines - A Review
Basak, D., Tiwari, A., & Das, S. (2006) · IEEE International Conference on Industrial Technology (ICIT) · doi:10.1109/icit.2006.372719 · Cited by 97 · cited 1×
“[1], [2] have presented a review of fault diagnosis in an induction machine, therefore it has not been discussed in detail in this paper to avoid repetition.”
Farooq, J., Srairi, S., Djerdir, A., & Miraoui, A. (2006) · IEEE Transactions on Magnetics · doi:10.1109/tmag.2006.870936 · Cited by 94
Rosu, M., Saitz, J., & Arkkio, A. (2005) · IEEE Transactions on Magnetics · doi:10.1109/tmag.2005.848319 · Cited by 91 · cited 1×
“The approximate maximum operation temperature of commercial magnets is illustrated in Fig. 8. To evaluate the effect on the parameters of the machines under demagnetization conditions, various analytical models have been proposed [ 7 ]-[11], which are discussed in Section III.”
Yoon, T. (2005) · IEEE Transactions on Magnetics · doi:10.1109/tmag.2005.848321 · Cited by 60
A fuzzy bp approach for diagnosis and prognosis of bearing faults in induction motors
Satish, B. S., & Sarma, N. D. R. (2005) · IEEE Power Engineering Society General Meeting · doi:10.1109/pes.2005.1489277 · Cited by 53 · cited 1×
“Some papers define “prognosis” as the estimation of Remaining Useful Life (RUL) [49], [50].”
Autonomous diagnostics and prognostics through competitive learning driven HMM-based clustering
Chinnam, R. B., & Baruah, P. (2004) · doi:10.1109/ijcnn.2003.1223951 · Cited by 51 · cited 1×
“In [51]-[54], prognosis is defined as the prediction/forecasting of future state during the evolution of a fault.”
Lee, J.-H., & Hong, J.-P. (2008) · IEEE Transactions on Magnetics · doi:10.1109/tmag.2007.916093 · Cited by 51
Motor bearing fault diagnosis by a fundamental frequency amplitude based fuzzy decision system
Goddu, G., Li, B., Chow, M., & Hung, J. C. (2002) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon.1998.724018 · Cited by 42 · cited 1×
“an if-then rule set [42]-[44].”
Yang, W., Tavner, P. J., & Wilkinson, M. (2008) · IET International Conference on Power Electronics, Machines and Drives (PEMD) · doi:10.1049/cp:20080473 · Cited by 32 · cited 1×
“Similar method is also used to detect dynamic eccentricity in PMSM and to monitor their health condition [23].”
MethodThe Noise and Vibration Analysis of BLDC Motor Due to Asymmetrical Permanent-Magnet Overhang Effects
Kang, G.-H., Son, Y.-D., & Kim, G.-T. (2008) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2008.2002278 · Cited by 31
Lasurt, I., Stronach, A. F., & Penman, J. (2002) · PeachFuzz 2000. 19th International Conference of the North American Fuzzy Information Processing Society - NAFIPS (Cat. No.00TH8500) · doi:10.1109/nafips.2000.877411 · Cited by 30 · cited 1×
“an if-then rule set [42]-[44].”
Residual evaluation for fault diagnosis based on adaptive fuzzy thresholds
Frank, P. M. (1995) · doi:10.1049/ic:19950512 · Cited by 28 · cited 1×
“To make it more adaptive to achieve more accurate solutions under different operation conditions, hybrid neural/fuzzy machine fault detectors are also under research [45]-[48], which take advantage of the learning capability of ANNs to optimize fuzzy sets.”
Faults diagnoses of rotating machines by using neural nets: GRNN and BPN
Hyun, B.-G., & Nam, K. (2002) · Proceedings of the Annual Conference of the IEEE Industrial Electronics Society · doi:10.1109/iecon.1995.484165 · Cited by 27 · cited 1×
“Various ANN structures are approved successful in brushless permanent magnet machine fault diagnosis [31], [34]-[39].”
Wang, W. (2005) · IMA Journal of Management Mathematics · doi:10.1093/imaman/dpi035 · Cited by 25
Synchronous Machine Steady-State Parameter Estimation Using Neural Networks
Calvo, M., & Malik, O. P. (2004) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2004.827041 · Cited by 21 · cited 1×
“implemented for parameter estimation in a supervised learning environment [31], [40], [41].”
Neural networks approach to electric machine on-line diagnostics
Filippetti, F., Franceschini, G., & Tassoni, C. (2002) · European Conference on Power Electronics and Applications · Cited by 17
Failure prognosis of DC starter motors using hidden Markov models
Zaidi, S. S. H., Aviyente, S., Salman, M. A., Shin, K.-K., & Strangas, E. G. (2009) · IEEE International Symposium on Diagnostics for Electrical Machines, Power Electronics and Drives (SDEMPED) · doi:10.1109/demped.2009.5292778 · Cited by 14 · cited 1×
“In [51]-[54], prognosis is defined as the prediction/forecasting of future state during the evolution of a fault.”
BackgroundIntegrated prognosis of AC servo motor driven linear actuator using Hidden Semi-Markov models
Wu, X. Z., Li, Y., Guru, A. K., & Lundell, T. D. (2009) · IEEE International Electric Machines & Drives Conference (IEMDC) · doi:10.1109/iemdc.2009.5075387 · Cited by 12
A symbolic reasoning approach to fault detection and isolation applied to electrical machines
Combastel, C., Gentil, S., & Rognon, J. P. (2002) · The proceedings of the IEEE Conference on Control Applications/The proceedings of the ... IEEE Conference on Control Applications · doi:10.1109/cca.1998.728494 · Cited by 10
Comparison of wavelet-based methods for the prognosis of failures in electric motors
Zanardelli, W. G., Strangas, E. G., Khalil, H. K., & Miller, J. M. (2005) · IEEE Workshop on Power Electronics in Transportation · doi:10.1109/pet.2002.1185551 · Cited by 10 · cited 1×
“In [55], [56], prognosis is defined as small transient signal detection.”
Application of Particle Swarm Optimization to PMSM Stator Fault Diagnosis
Liu, L., Cartes, D. A., & Liu, W. (2006) · 2022 International Joint Conference on Neural Networks (IJCNN) · doi:10.1109/ijcnn.2006.246942 · Cited by 10
Chow, M., & Goode, P. V. (2002) · Conference proceedings · doi:10.1109/mwscas.1993.342948 · Cited by 9 · cited 1×
“Various ANN structures are approved successful in brushless permanent magnet machine fault diagnosis [31], [34]-[39].”
Effect of design variables on irreversible magnet demagnetization in brushless dc motor
Kim, T. H., & Lee, J. (2005) · Journal of Applied Physics · doi:10.1063/1.1855272 · Cited by 8 · cited 1×
“To evaluate the effect on the parameters of the machines under demagnetization conditions, various analytical models have been proposed [7]-[11], which are discussed in Section III.”
MethodAutomated monitoring of magnet quality for permanent magnet synchronous motors at standstill
Hong, J., Hyun, D., Lee, S. B., Yoo, J., & Lee, K. (2009) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2009.5316464 · Cited by 7
Parameters estimation of nonlinear models of DC motors using neural networks
El-Arabawy, I. F., Yousef, H., Mostafa, M. Z., & Abdul-Kader, H. M. (2002) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon.2000.972582 · Cited by 4 · cited 1×
“implemented for parameter estimation in a supervised learning environment [31], [40], [41].”
Faults Diagnoses of Rotating Machines by Using Neural Nets : GRNN and BPN
남광희 (1995) · Open Access System for Information Sharing (Pohang University of Science and Technology) · Cited by 3
Cited by
Fault Diagnosis and Fault-Tolerant Control of PMSM Drives–State of the Art and Future Challenges
Orlowska-Kowalska, T., Wolkiewicz, M., Pietrzak, P., Skowron, M., Ewert, P., Tarchala, G., Krzysztofiak, M., & Kowalski, C. T. (2022) · IEEE Access · doi:10.1109/access.2022.3180153 · Cited by 328
“Damage to the insulation results from abrasion caused by mechanical stress or overheating of the winding as a result of excessive loads on the motor [14]-[20], [23], [26], [27].”
BackgroundMethodInfluentialAn Effective Stator Fault Diagnosis Framework of BLDC Motor Based on Vibration and Current Signals
Shifat, T. A., & Hur, J.-W. (2020) · IEEE Access · doi:10.1109/access.2020.3000856 · Cited by 125
“A detailed survey of BLDC motors faults can be found in [14].”
BackgroundMoosavi, S. S., Djerdir, A., Amirat, Y. A., & Khaburi, D. A. (2015) · Journal of Magnetism and Magnetic Materials · doi:10.1016/j.jmmm.2015.04.062 · Cited by 96
Yang, Z., Shi, X., & Krishnamurthy, M. (2014) · 2014 IEEE Transportation Electrification Conference and Expo (ITEC) · doi:10.1109/itec.2014.6861774 · Cited by 72
“INTRODUCTION Vibration monitoring [1-6] as a non-intrusive approach, is extensively used for electric fault diagnosis of PMSM.”
BackgroundSelf-citationZhang, J., Xu, Z., Wang, J., Zhao, J., Din, Z., & Cheng, M. (2020) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2020.3009563 · Cited by 75
“The investigation shows that about 37% of all possible failures of the PMSM occur in the stator [2].”
Background
Metadata
- Authors
- Da, Y., Shi, X., & Krishnamurthy, M.
- Affiliations
- Illinois Institute of Technology (US)
- Venue
- 2011 IEEE Vehicle Power and Propulsion Conference
- Publisher
- IEEE
- Published
- 2011-09
- Pages
- 1-7
- OpenAlex
- W2127013354
- Cited by
- 96
- References
- 62
- Citations by year
- 2026: 2 · 2025: 8 · 2024: 9 · 2023: 3 · 2022: 10 · 2021: 3 · 2020: 14 · 2019: 5 · 2018: 5 · 2017: 5 · 2016: 10 · 2015: 7 · 2014: 9 · 2013: 4 · 2012: 2
- FWCI
- 8.03
- Type
- conference paper
- Language
- en
- Open access
- closed
- Locations
- IEEE Vehicle Power and Propulsion Conference (VPPC) (publishedVersion)
- Topics
- Physical Sciences › Engineering › Control and Systems Engineering › Machine Fault Diagnosis Techniques
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Electric Motor Design and Analysis
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Sensorless Control of Electric Motors
- Keywords
- permanent magnet brushless machines, condition monitoring, fault diagnosis, failure prediction, health monitoring, rare-earth permanent magnets, predictive maintenance
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.