The DOI matches its Crossref record; 74 of the 74 references it cites were found in a registry or an index.
Current Status and Perspectives on Wire and Arc Additive Manufacturing (WAAM)
Open accessAbstract
Additive manufacturing has revolutionized the manufacturing paradigm in recent years due to the possibility of creating complex shaped three-dimensional parts which can be difficult or impossible to obtain by conventional manufacturing processes. Among the different additive manufacturing techniques, wire and arc additive manufacturing (WAAM) is suitable to produce large metallic parts owing to the high deposition rates achieved, which are significantly larger than powder-bed techniques, for example. The interest in WAAM is steadily increasing, and consequently, significant research efforts are underway. This review paper aims to provide an overview of the most significant achievements in WAAM, highlighting process developments and variants to control the microstructure, mechanical properties, and defect generation in the as-built parts; the most relevant engineering materials used; the main deposition strategies adopted to minimize residual stresses and the effect of post-processing heat treatments to improve the mechanical properties of the parts. An important aspect that still hinders this technology is certification and nondestructive testing of the parts, and this is discussed. Finally, a general perspective of future advancements is presented.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Additive manufacturing of metallic components – Process, structure and properties
DebRoy, T., Wei, H. L., Zuback, J. S., Mukherjee, T., Elmer, J. W., Milewski, J. O., Beese, A. M., Wilson-Heid, A., De, A., & Zhang, W. (2018) · Progress in Materials Science · doi:10.1016/j.pmatsci.2017.10.001 · Cited by 8,805
Design for Additive Manufacturing: Trends, opportunities, considerations, and constraints
Thompson, M. K., Moroni, G., Vaneker, T., Fadel, G., Campbell, R. I., Gibson, I., Bernard, A., Schulz, J., Graf, P., Ahuja, B., et al. (2016) · CIRP Annals · doi:10.1016/j.cirp.2016.05.004 · Cited by 2,017
Wire + Arc Additive Manufacturing
Williams, S., Martina, F., Addison, A. C., Ding, J., Pardal, G., & Colegrove, P. A. (2015) · Materials Science and Technology · doi:10.1179/1743284715y.0000000073 · Cited by 1,971
A transformation for extracting new descriptors of shape
Blum, H. E. (1967) · Medical Entomology and Zoology · Cited by 1,753
Ding, D., Pan, Z., Cuiuri, D., & Li, H. (2015) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-015-7077-3 · Cited by 1,648
Residual stress. Part 1 – Measurement techniques
Withers, P. J., & Bhadeshia, H. K. D. H. (2001) · Materials Science and Technology · doi:10.1179/026708301101509980 · Cited by 1,620
Wu, B., Pan, Z., Ding, D., Cuiuri, D., Li, H., Xu, J., & Norrish, J. (2018) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2018.08.001 · Cited by 1,577
Carroll, B. E., Palmer, T. A., & Beese, A. M. (2015) · Acta Materialia · doi:10.1016/j.actamat.2014.12.054 · Cited by 1,507
Review of in-situ process monitoring and in-situ metrology for metal additive manufacturing
Everton, S. K., Hirsch, M., Stravroulakis, P., Leach, R. K., & Clare, A. T. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.01.099 · Cited by 1,469
Buchanan, C., & Gardner, L. (2019) · Engineering Structures · doi:10.1016/j.engstruct.2018.11.045 · Cited by 826
Welding, Brazing, and Soldering
(1993) · ASM International eBooks · doi:10.31399/asm.hb.v06.9781627081733 · Cited by 805
Microstructure and Mechanical Properties of Wire and Arc Additive Manufactured Ti-6Al-4V
Wang, F., Williams, S., Colegrove, P., & Antonysamy, A. A. (2013) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-012-1444-6 · Cited by 737
Investigation of the benefits of plasma deposition for the additive layer manufacture of Ti–6Al–4V
Martina, F., Mehnen, J., Williams, S., Colegrove, P. A., & Wang, F. (2012) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2012.02.002 · Cited by 641
Cong, B., Ding, J., & Williams, S. (2014) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-014-6346-x · Cited by 581
A multi-bead overlapping model for robotic wire and arc additive manufacturing (WAAM)
Ding, D., Pan, Z. S., Cuiuri, D., & Li, H. (2014) · Robotics and Computer-Integrated Manufacturing · doi:10.1016/j.rcim.2014.08.008 · Cited by 577
Colegrove, P. A., Coules, H., Fairman, J., Martina, F., Kashoob, T., Mamash, H., & Cozzolino, L. D. (2013) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2013.04.012 · Cited by 567
Denlinger, E. R., Heigel, J. C., Michaleris, P., & Palmer, T. A. (2014) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2014.07.030 · Cited by 531
Wang, L., Xue, J., & Wang, Q. (2019) · Materials Science and Engineering A · doi:10.1016/j.msea.2019.02.078 · Cited by 496
Microstructure and texture evolution during solidification processing of Ti–6Al–4V
Kobryn, P. A., & Semiatin, S. L. (2003) · Journal of Materials Processing Technology · doi:10.1016/s0924-0136(02)00865-8 · Cited by 433
Gu, J., Ding, J., Williams, S. W., Gu, H., Ma, P., & Zhai, Y. (2016) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2015.11.006 · Cited by 431
Gu, J., Ding, J., Williams, S. W., Gu, H., Bai, J., Zhai, Y., & Ma, P. (2016) · Materials Science and Engineering: A · doi:10.1016/j.msea.2015.10.101 · Cited by 413
Bermingham, M. J., Kent, D., Zhan, H., StJohn, D. H., & Dargusch, M. S. (2015) · Acta Materialia · doi:10.1016/j.actamat.2015.03.035 · Cited by 411
Sun, R., Li, L., Zhu, Y., Guo, W., Peng, P., Cong, B., Sun, J., Che, Z., Li, B., Guo, C., et al. (2018) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2018.02.353 · Cited by 382
Low cost integration of additive and subtractive processes for hybrid layered manufacturing
Karunakaran, K. P., Suryakumar, S., Pushpa, V., & Akula, S. (2010) · Robotics and Computer-Integrated Manufacturing · doi:10.1016/j.rcim.2010.03.008 · Cited by 377
Donoghue, J. M., Antonysamy, A. A., Martina, F., Colegrove, P. A., Williams, S., & Prangnell, P. B. (2016) · Materials Characterization · doi:10.1016/j.matchar.2016.02.001 · Cited by 369
Ding, D., Pan, Z. S., Cuiuri, D., & Li, H. (2015) · Robotics and Computer-Integrated Manufacturing · doi:10.1016/j.rcim.2015.01.003 · Cited by 363
Wu, B., Ding, D., Pan, Z. S., et al. (2017) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2017.07.037 · Cited by 352
Brandl, E., Baufeld, B., Leyens, C., & Gault, R. (2010) · Physics Procedia · doi:10.1016/j.phpro.2010.08.087 · Cited by 348
Carter, L. N., Attallah, M. M., & Reed, R. C. (2012) · Wiley eBooks · doi:10.1002/9781118516430.ch64 · Cited by 342
Zhang, C., Li, Y., Gao, M. X., & Zeng, X. (2017) · Materials Science and Engineering A · doi:10.1016/j.msea.2017.11.084 · Cited by 335
Microstructure of Interpass Rolled Wire + Arc Additive Manufacturing Ti-6Al-4V Components
Martina, F., Colegrove, P. A., Williams, S., & Meyer, J. (2015) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-015-3172-1 · Cited by 328
Rodrigues, T. A., Duarte, V., Avila, J. A., Santos, T. G., Miranda, R. M., & Oliveira, J. P. (2019) · Additive Manufacturing · doi:10.1016/j.addma.2019.03.029 · Cited by 328
Self-citationAdditive manufacturing of Ni-based superalloys: The outstanding issues
Attallah, M. M., Jennings, R., Wang, X., & Carter, L. N. (2016) · MRS Bulletin · doi:10.1557/mrs.2016.211 · Cited by 318
Recent advances in grain refinement of light metals and alloys
Easton, M. A., Qian, M., Prasad, A., & StJohn, D. H. (2016) · Current Opinion in Solid State and Materials Science · doi:10.1016/j.cossms.2015.10.001 · Cited by 308
Additive manufacturing using WAAM with AA5183 wire
Horgar, A., Fostervoll, H., Nyhus, B., et al. (2018) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2018.04.014 · Cited by 304
Bai, X., Colegrove, P. A., Ding, J., Zhou, X., Diao, C., Bridgeman, P., Hönnige, J., Zhang, H., & Williams, S. (2018) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.03.085 · Cited by 303
Wang, J. F., Sun, Q. J., Wang, H., Liu, J. P., & Feng, J. C. (2016) · Materials Science and Engineering: A · doi:10.1016/j.msea.2016.09.015 · Cited by 282
Wang, F., Williams, S., & Rush, M. T. (2011) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-011-3299-1 · Cited by 280
Yang, D., Wang, G., & Zhang, G. (2017) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2017.01.024 · Cited by 267
Fabrication of geometrical features using wire and arc additive manufacture
Kazanas, P., Deherkar, P., Almeida, P., Lockett, H., & Williams, S. (2012) · Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture · doi:10.1177/0954405412437126 · Cited by 261
Ou, W., Mukherjee, T., Knapp, G. L., Wei, Y., & DebRoy, T. (2018) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.08.111 · Cited by 257
Grain-refinement mechanisms in titanium alloys
Bermingham, M. J., McDonald, S. D., Dargusch, M. S., & StJohn, D. H. (2008) · Journal of materials research/Pratt's guide to venture capital sources · doi:10.1557/jmr.2008.0002 · Cited by 256
Finite element modeling of multi-pass welding and shaped metal deposition processes
Chiumenti, M., Cervera, M., Salmi, A., Agelet de Saracibar, C., Dialami, N., & Matsui, K. (2010) · Computer Methods in Applied Mechanics and Engineering · doi:10.1016/j.cma.2010.02.018 · Cited by 245
McAndrew, A. R., Alvarez Rosales, M., Colegrove, P. A., Hönnige, J. R., Ho, A., Fayolle, R., Eyitayo, K., Stan, I., Sukrongpang, P., Crochemore, A., et al. (2018) · Additive Manufacturing · doi:10.1016/j.addma.2018.03.006 · Cited by 243
Residual stress of as-deposited and rolled wire+arc additive manufacturing Ti–6Al–4V components
Martina, F., Roy, M. J., Szost, B. A., Terzi, S., Colegrove, P. A., Williams, S., Withers, P. J., Meyer, J., & Hofmann, M. (2016) · Materials Science and Technology · doi:10.1080/02670836.2016.1142704 · Cited by 242
Guo, J., Zhou, Y., Liu, C., Wu, Q., Chen, X., & Lu, J. (2016) · Materials · doi:10.3390/ma9100823 · Cited by 241
Fabricating Superior NiAl Bronze Components through Wire Arc Additive Manufacturing
Ding, D., Pan, Z. S., van Duin, S., Li, H., & Shen, C. (2016) · Materials · doi:10.3390/ma9080652 · Cited by 238
Bermingham, M. J., Nicastro, L., Kent, D., Chen, Y., & Dargusch, M. S. (2018) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2018.04.158 · Cited by 227
Ding, D., Shen, C., Pan, Z. S., Cuiuri, D., Li, H., Larkin, N., & van Duin, S. (2016) · Computer-Aided Design · doi:10.1016/j.cad.2015.12.003 · Cited by 212
Control of residual stress and distortion in aluminium wire + arc additive manufacture with rolling
Hönnige, J. R., Colegrove, P. A., Ganguly, S., Eimer, E., Kabra, S., & Williams, S. (2018) · Additive Manufacturing · doi:10.1016/j.addma.2018.06.015 · Cited by 203
Hönnige, J. R., Colegrove, P. A., Ahmad, B., Fitzpatrick, M. E., Ganguly, S., Lee, T. L., & Williams, S. W. (2018) · Materials & Design · doi:10.1016/j.matdes.2018.03.065 · Cited by 200
Idle time selection for wire-arc additive manufacturing: A finite element-based technique
Montevecchi, F., Venturini, G., Grossi, N., Scippa, A., & Campatelli, G. (2018) · Additive manufacturing · doi:10.1016/j.addma.2018.01.007 · Cited by 185
Shen, C., Pan, Z. S., Cuiuri, D., Roberts, J., & Li, H. (2015) · Metallurgical and Materials Transactions B · doi:10.1007/s11663-015-0509-5 · Cited by 181
Xiong, J., Yin, Z., & Zhang, W. (2016) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2016.02.021 · Cited by 170
Design for additive manufacturing with site-specific properties in metals and alloys
Tammas-Williams, S., & Todd, I. (2017) · Scripta Materialia · doi:10.1016/j.scriptamat.2016.10.030 · Cited by 167
Microstructure and mechanical property considerations in additive manufacturing of aluminum alloys
Ding, Y., Muñiz-Lerma, J. A., Trask, M., Chou, S. C., Walker, A., & Brochu, M. (2016) · MRS Bulletin · doi:10.1557/mrs.2016.214 · Cited by 161
Li, F., Chen, S., Shi, J., Zhao, Y., & Tian, H. (2018) · Applied Sciences · doi:10.3390/app8020207 · Cited by 153
Design for Wire + Arc Additive Manufacture: design rules and build orientation selection
Lockett, H., Ding, J., Williams, S., & Martina, F. (2017) · Journal of Engineering Design · doi:10.1080/09544828.2017.1365826 · Cited by 147
Bobbio, L. D., Bocklund, B. J., Otis, R., Borgonia, J. P., Dillon, R. P., Shapiro, A. A., McEnerney, B. W., Liu, Z., & Beese, A. M. (2018) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2018.01.156 · Cited by 135
Shen, C., Pan, Z. S., Ding, D., Yuan, L., Nie, N., Wang, Y., Luo, D., Cuiuri, D., van Duin, S., & Li, H. (2018) · Additive manufacturing · doi:10.1016/j.addma.2018.08.008 · Cited by 127
Introduction to the design rules for Metal Big Area Additive Manufacturing
Greer, C. M., Nycz, A., Noakes, M., Richardson, B. S., Post, B., Kurfess, T. R., & Love, L. J. (2019) · Additive manufacturing · doi:10.1016/j.addma.2019.02.016 · Cited by 125
Development of a laminar flow local shielding device for wire + arc additive manufacture
Ding, J., Colegrove, P. A., Martina, F., Williams, S., Wiktorowicz, R., & Palt, M. R. (2015) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2015.07.005 · Cited by 120
Preliminary development of a Wire and Arc Additive Manufacturing system (WAAM)
Prado-Cerqueira, J. L., Diéguez, J. L., & Camacho, A. M. (2017) · Procedia Manufacturing · doi:10.1016/j.promfg.2017.09.154 · Cited by 117
Gómez-Ortega, A., Galvan, L. C., Deschaux‐Beaume, F., Mezrag, B., & Rouquette, S. (2017) · Science and Technology of Welding & Joining · doi:10.1080/13621718.2017.1388995 · Cited by 114
Takagi, H., SASAHARA, H., Abe, T., Sannomiya, H., Nishiyama, S., Ohta, S., & Nakamura, K. (2018) · Additive manufacturing · doi:10.1016/j.addma.2018.10.026 · Cited by 112
Online measurement of bead geometry in GMAW-based additive manufacturing using passive vision
Xiong, J., & Zhang, G. (2013) · Measurement Science and Technology · doi:10.1088/0957-0233/24/11/115103 · Cited by 104
Xu, F., Dhokia, V. G., Colegrove, P. A., McAndrew, A. R., Williams, S., Henstridge, A., & Newman, S. T. (2018) · International Journal of Computer Integrated Manufacturing · doi:10.1080/0951192x.2018.1466395 · Cited by 101
Residual stress analysis in laser welded NiTi sheets using synchrotron X-ray diffraction
Oliveira, J. P., Fernandes, F. M. B., Miranda, R. M., Schell, N., & Moreno, J. L. O. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.03.137 · Cited by 86
Self-citationXu, X., Ding, J., Ganguly, S., Diao, C., & Williams, S. (2018) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-018-3521-5 · Cited by 80
In situ formation of substrate release mechanisms for gas metal arc weld metal 3-D printing
Haselhuhn, A. S., Wijnen, B., Anzalone, G. C., Sanders, P. G., & Pearce, J. M. (2015) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2015.06.038 · Cited by 75
Mughal, M. P., Fawad, H., Mufti, R. A., & Siddique, M. A. B. (2005) · Modelling and Simulation in Materials Science and Engineering · doi:10.1088/0965-0393/13/7/013 · Cited by 72
Xu, X., Ganguly, S., Ding, J., Dirisu, P., Martina, F., Liu, X., & Williams, S. (2018) · Materials Science and Engineering A · doi:10.1016/j.msea.2018.12.114 · Cited by 69
Jurić, I., Garašić, I., Bušić, M., & Kožuh, Z. (2018) · JOM · doi:10.1007/s11837-018-3151-2 · Cited by 67
Zalameda, J. N., Burke, E., Hafley, R. A., Taminger, K. M. B., Domack, C. S., Brewer, A., & Martin, R. E. (2013) · Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE · doi:10.1117/12.2018233 · Cited by 59
Cited by
Svetlizky, D., Das, M., Zheng, B., Vyatskikh, A. L., Bose, S., Bandyopadhyay, A., Schoenung, J. M., Lavernia, E. J., & Eliaz, N. (2021) · Materials Today · doi:10.1016/j.mattod.2021.03.020 · Cited by 1,371
Directed Energy Deposition (DED) Process: State of the Art
Ahn, D.-G. (2021) · International Journal of Precision Engineering and Manufacturing-Green Technology · doi:10.1007/s40684-020-00302-7 · Cited by 803
Saleh, B., Jiang, J., Fathi, R., Al-hababi, T., Xu, Q., Wang, L., Song, D., & Ma, A. (2020) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2020.108376 · Cited by 738
Revisiting fundamental welding concepts to improve additive manufacturing: From theory to practice
Oliveira, J. P., Santos, T. G., & Miranda, R. M. (2020) · Progress in Materials Science · doi:10.1016/j.pmatsci.2019.100590 · Cited by 617
Self-citationAn overview of modern metal additive manufacturing technology
Armstrong, M., Mehrabi, H., & Naveed, N. (2022) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2022.10.060 · Cited by 549
Metadata
- Authors
- Rodrigues, T. A., Duarte, V., Miranda, R. M., Santos, T. G., & Oliveira, J. P.
- Venue
- Materials
- Publisher
- MDPI AG
- Published
- 2019-04-04
- Volume
- 12
- Issue
- 7
- Pages
- 1121
- ISSN
- 1996-1944 (ISSN-L)
- OpenAlex
- W2930365861
- Cited by
- 779
- References
- 74
- FWCI
- 42.57
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.