Synergistic Effects of Nucleating Agents and Plasticizers on the Crystallization Behavior of Poly(lactic acid)
Open accessThe DOI matches its Crossref record; 11 of the 11 references it cites were found in a registry or an index.
Abstract
The synergistic effect of nucleating agents and plasticizers on the thermal and mechanical performance of PLA nanocomposites was investigated with the objective of increasing the crystallinity and balancing the stiffness and toughness of PLA mechanical properties. Calcium carbonate, halloysite nanotubes, talc and LAK (sulfates) were compared with each other as heterogeneous nucleating agents. Both the DSC isothermal and non-isothermal studies indicated that talc and LAK were the more effective nucleating agents among the selected fillers. Poly(D-lactic acid) (PDLA) acted also as a nucleating agent due to the formation of the PLA stereocomplex. The half crystallization time was reduced by the addition of talc to about 2 min from 37.5 min of pure PLA by the isothermal crystallization study. The dynamic mechanical thermal study (DMTA) indicated that nanofillers acted as both reinforcement fillers and nucleating agents in relation to the higher storage modulus. The plasticized PLA studied by DMTA indicated a decreasing glass transition temperature with the increasing of the PEG content. The addition of nanofiller increased the Young’s modulus. PEG had the plasticization effect of increasing the break deformation, while sharply decreasing the stiffness and strength of PLA. The synergistic effect of nanofillers and plasticizer achieved the balance between stiffness and toughness with well-controlled crystallization.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Processing technologies for poly(lactic acid)
Lim, L.-T., Auras, R., & Rubino, M. (2008) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2008.05.004 · Cited by 2,766
Poly(lactic acid) modifications
Rasal, R. M., Janorkar, A. V., & Hirt, D. E. (2010) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2009.12.003 · Cited by 2,204 · cited 1×
“Poly (lactic acid) has been the subject of much attention because of its outstanding performance in terms of high stiffness and strength, biodegradability and thermal processability and is often seen as an alternative to traditional petrochemical plastic [1,2].”
BackgroundFischer, E. W., Sterzel, H. J., & Wegner, G. (1973) · Kolloid-Zeitschrift und Zeitschrift für Polymere · doi:10.1007/bf01498927 · Cited by 1,704
New emerging trends in synthetic biodegradable polymers—Polylactide: A critique
Gupta, A. P., & Kumar, V. (2007) · European Polymer Journal · doi:10.1016/j.eurpolymj.2007.06.045 · Cited by 941 · cited 1×
“Gupta and Kumar [5] reviewed various aspects of PLA synthesis and mentioned the kinds of catalysts in the production of PLA.”
BackgroundEffect of nucleation and plasticization on the crystallization of poly (lactic acid)
Li, H., & Huneault, M. A. (2007) · Polymer · doi:10.1016/j.polymer.2007.09.020 · Cited by 810 · cited 2×
“Basically, the normal nucleating agents reported by some groups are various kinds of inorganic nanoparticles, such as talc, sodium stearate, calcium lactate [8], montmorillonite (MMT) and carbon nanotubes (CNT) [9,10].”
BackgroundFrom Lactic Acid to Poly(lactic acid) (PLA): Characterization and Analysis of PLA and Its Precursors
Inkinen, S., Hakkarainen, M., Albertsson, A.-C., & Södergård, A. (2011) · Biomacromolecules · doi:10.1021/bm101302t · Cited by 710 · cited 1×
“By and large, commercial PLA products with a high molar mass are usually produced from lactide, the ring-formed dimer of lactic acid, via the ring-opening polymerization (ROP) route [4].”
BackgroundPolymorphism and isomorphism in biodegradable polyesters
Pan, P., & Inoue, Y. (2009) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2009.01.003 · Cited by 611 · cited 1×
“It has been reported [6] that PLA can crystallize in three forms (α, β and γ), depending on the composition of the optically-active L- and D,L-lactide, and the α phase is more stable and has a melting temperature of 180 °C compared to the β phase, with 175 °C [7].”
BackgroundPreparation and Properties of Plasticized Poly(lactic acid) Films
Ljungberg, N., & Wesslén, B. (2005) · Biomacromolecules · doi:10.1021/bm050098f · Cited by 331 · cited 1×
“For example, polyethylene glycol (PEG), polypropylene glycol (PPG), glycerol and citrate ester are investigated as plasticizers for PLA to lower its glass transition temperature, increase ductility and improve processability [14–16].”
BackgroundPlasticization of Poly(l-lactide) with Poly(propylene glycol)
Kulinski, Z., Piorkowska, E., Gadzinowska, K., & Stasiak, M. (2006) · Biomacromolecules · doi:10.1021/bm060089m · Cited by 320
Plasticization of semicrystalline poly(l-lactide) with poly(propylene glycol)
Piorkowska, E., Kulinski, Z., Galeski, A., & Masirek, R. (2006) · Polymer · doi:10.1016/j.polymer.2006.03.115 · Cited by 301 · cited 1×
“For example, polyethylene glycol (PEG), polypropylene glycol (PPG), glycerol and citrate ester are investigated as plasticizers for PLA to lower its glass transition temperature, increase ductility and improve processability [14–16].”
BackgroundEffect of the addition of poly (D-lactic acid) on the thermal property of poly (L-lactic acid)
Yamane, H., & Sasai, K. (2003) · Polymer · doi:10.1016/s0032-3861(03)00092-2 · Cited by 266 · cited 1×
“Yamane and coworkers [11] analyzed the crystallization behavior of PLLA with PDLA as a nucleating agent, which formed a large stereocomplex crystalline and effectively increased the number of PLLA spherulites and then the overall crystallization rate.”
Background
Cited by
PLA composites: From production to properties
Murariu, M., & Dubois, P. (2016) · Advanced Drug Delivery Reviews · doi:10.1016/j.addr.2016.04.003 · Cited by 1,005
Chemical Modification and Foam Processing of Polylactide (PLA)
Standau, T., Zhao, C., Murillo Castellón, S., Bonten, C., & Altstädt, V. (2019) · Polymers · doi:10.3390/polym11020306 · Cited by 210
“Various nucleating agents were applied for compact PLA, such as talc [224,225], carbon nanotubes [226], calcium carbonate, montmorillonite [227], etc.”
In vivo and Post-synthesis Strategies to Enhance the Properties of PHB-Based Materials: A Review
Turco, R., Santagata, G., Corrado, I., Pezzella, C., & Di Serio, M. (2021) · Frontiers in Bioengineering and Biotechnology · doi:10.3389/fbioe.2020.619266 · Cited by 169
Redox Switchable Copolymerization of Cyclic Esters and Epoxides by a Zirconium Complex
Quan, S. M., Wang, X., Zhang, R., & Diaconescu, P. L. (2016) · Macromolecules · doi:10.1021/acs.macromol.6b00997 · Cited by 93
Combined effect of nucleating agent and plasticizer on the crystallization behaviour of polylactide
Anakabe, J., Zaldua Huici, A. M., Eceiza, A., Arbelaiz, A., & Avérous, L. (2017) · Polymer Bulletin · doi:10.1007/s00289-017-1989-z · Cited by 38
Metadata
- Authors
- Shi, X., Zhang, G., Phuong, T., & Lazzeri, A.
- Venue
- Molecules
- Publisher
- MDPI AG
- Published
- 2015-01-19
- Volume
- 20
- Issue
- 1
- Pages
- 1579-1593
- ISSN
- 1420-3049 (ISSN-L)
- OpenAlex
- W2000650429
- Cited by
- 135
- References
- 11
- FWCI
- 7.61
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.