CoChat

High‐Performance Recyclable Polyester Elastomers Through Transient Strain‐Stiffening

Open access

The DOI matches its Crossref record; 80 of the 80 references it cites were found in a registry or an index.

Abstract

Polyester thermoplastic elastomers are promising sustainable materials but their mechanical properties need improvement, in particular, attempts to increase strength often result in compromised elasticity. Strong and tough elastomers are known but require complex polymer formulations together with control over cross‐linking or crystallinity, both of which challenge recycling. Here, the introduction of transient strain‐stiffening approaches into fully amorphous structures show both strengthening and toughening of elastomers while conserving recyclability. The new amorphous block polyester elastomers are prepared by controlled polymerization methods using commercial monomers. The block polymers comprise a central poly(ɛ‐caprolactone‐ co ‐ɛ‐decalactone) block flanked by poly(cyclohexene oxide‐ alt ‐phthalate) blocks. Elastomer thermomechanical properties are tuned by varying ratios of ɛ‐caprolactone to ɛ‐decalactone within the mid‐block to access materials with excellent mechanical properties. The best elastomers feature 30–50 wt.% polycaprolactone and exhibit tensile strengths up to 40 MPa, elongations at break above 2000%, with excellent elastic recovery (>90%). These materials exhibit strain‐induced crystallization and outperform current commercial elastomers, entering a new region of tensile mechanical property space. They have service temperature ranges from −60 to 140 °C and high temperature stability (≥300 °C), with wide thermal (re)processing windows. These new polyester elastomers also show high resistance to creep, humidity resistance, and excellent recyclability.

Overview

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1002/adma.202416674

Cites

80 of 80 references verified0 citation errors · 0 not checkable

Statistics

Figures

Figure 1 Synthesis of the block polyesters. i) ROP of ɛ‐CL and ɛ‐DL, 80 °C, catalyst = [LZnMg(C6F5)2], where [LZnMg(C6F5)2]0: [BDM]0: [lactone]0: [PA]0: [CHO]0 = 1: 2: 2000: 384: 577 and [lactone]0 = 1.0 m in toluene. ii) ROCOP of CHO and PA, 110 °C, excess of CHO (1.5 equiv. relative to PA).
Figure 1 Synthesis of the block polyesters. i) ROP of ɛ‐CL and ɛ‐DL, 80 °C, catalyst = [LZnMg(C6F5)2], where [LZnMg(C6F5)2]0: [BDM]0: [lactone]0: [PA]0: [CHO]0 = 1: 2: 2000: 384: 577 and [lactone]0 = 1.0 m in toluene. ii) ROCOP of CHO and PA, 110 °C, excess of CHO (1.5 equiv. relative to PA).CC BY · PubMed Central
Figure 2 a) Dynamic mechanical thermal analysis (DMTA) temperature sweeps for P‐3, OTW = operating temperature window. b) Storage moduli from DMTA temperature sweeps for P‐2, P‐3, and P‐4.
Figure 2 a) Dynamic mechanical thermal analysis (DMTA) temperature sweeps for P‐3, OTW = operating temperature window. b) Storage moduli from DMTA temperature sweeps for P‐2, P‐3, and P‐4.CC BY · PubMed Central
Figure 3 Room‐temperature small‐angle X‐ray scattering (SAXS) profiles showing principal scattering peaks (q*) and higher‐order peaks (q/q*).
Figure 3 Room‐temperature small‐angle X‐ray scattering (SAXS) profiles showing principal scattering peaks (q*) and higher‐order peaks (q/q*).CC BY · PubMed Central
Figure 4 a) Tensile stress‐strain curves (representative of five repeats). b) Creep‐recovery experiments for lead samples P‐3 to P‐5. Comparison of c) tensile strength, d) strain at break, e) tensile toughness, and f) Young's modulus for materials P‐1 to P‐5.
Figure 4 a) Tensile stress‐strain curves (representative of five repeats). b) Creep‐recovery experiments for lead samples P‐3 to P‐5. Comparison of c) tensile strength, d) strain at break, e) tensile toughness, and f) Young's modulus for materials P‐1 to P‐5.CC BY · PubMed Central
Figure 5 a) Cyclic testing for P‐3 (200% strain) exhibiting narrow hysteresis (offset by 50% for clarity). b) Comparison of elastic recovery (ER), resilience, and residual strain (ɛR) for P‐2, P‐3, P‐4, and P‐5. c) Cyclic tensile testing for P‐3 to different % strains (offset for clarity). d) Corresponding elasticity properties at different % strains for P‐3.
Figure 5 a) Cyclic testing for P‐3 (200% strain) exhibiting narrow hysteresis (offset by 50% for clarity). b) Comparison of elastic recovery (ER), resilience, and residual strain (ɛR) for P‐2, P‐3, P‐4, and P‐5. c) Cyclic tensile testing for P‐3 to different % strains (offset for clarity). d) Corresponding elasticity properties at different % strains for P‐3.CC BY · PubMed Central
Figure 6 a) Evolution of 2D‐WAXS patterns of P‐3 recorded at increasing % strain (ɛ) and after recovery to 0% strain. 1D‐WAXS intensity profiles at increasing % strain (ɛ) and after recovery to 0% strain for b) P‐3 and c) P‐4. d) Tensile stress‐strain curves for P‐3 and P‐4 showing the crystallization onset strain (ɛonset). e) Schematic showing strain‐induced crystallization.
Figure 6 a) Evolution of 2D‐WAXS patterns of P‐3 recorded at increasing % strain (ɛ) and after recovery to 0% strain. 1D‐WAXS intensity profiles at increasing % strain (ɛ) and after recovery to 0% strain for b) P‐3 and c) P‐4. d) Tensile stress‐strain curves for P‐3 and P‐4 showing the crystallization onset strain (ɛonset). e) Schematic showing strain‐induced crystallization.CC BY · PubMed Central
Figure 7 a) Tensile strength, b) Strain at the break, c) Tensile toughness, and d) Young's Modulus for virgin P‐3 after five mechanical reprocessing cycles. Mean values ± std. dev. from measurements conducted independently on five specimens.
Figure 7 a) Tensile strength, b) Strain at the break, c) Tensile toughness, and d) Young's Modulus for virgin P‐3 after five mechanical reprocessing cycles. Mean values ± std. dev. from measurements conducted independently on five specimens.CC BY · PubMed Central
Figure 8 a) Comparison of operating temperature window for P‐1 to P‐5 with commercial TPEs. b) Ashby plot produced using mechanical data for commercial TPEs compared with P‐1 to P‐5.[ 32 ] PU = polyurethane, COPE = copolyester elastomer, PA = polyamide, SEBS = poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene), SIS = styrene‐isoprene‐styrene, SBS = styrene‐butadiene‐styrene, MPR = melt processable rubber, TPV = thermoplastic vulcanizates, TPO = thermoplastic polyolefin.
Figure 8 a) Comparison of operating temperature window for P‐1 to P‐5 with commercial TPEs. b) Ashby plot produced using mechanical data for commercial TPEs compared with P‐1 to P‐5.[ 32 ] PU = polyurethane, COPE = copolyester elastomer, PA = polyamide, SEBS = poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene), SIS = styrene‐isoprene‐styrene, SBS = styrene‐butadiene‐styrene, MPR = melt processable rubber, TPV = thermoplastic vulcanizates, TPO = thermoplastic polyolefin.CC BY · PubMed Central

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Claims other papers make about this one

Each is checked against this paper’s own text: does it say what the citing paper says it does?

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Research works printed but not linked: 7

  1. Dupont J., 2000, J. Braz. Chem. Soc., 11, 239
  2. Miao X., 2024, Angew. Chem., Int. Ed.
  3. Drobny J. G., 2014, Handbook of Thermoplastic Elastomers, Ch6
  4. Drobny J. G., 2014, Handbook of Thermoplastic Elastomers, Ch7
  5. Drobny J. G., 2014, Handbook of Thermoplastic Elastomers, Ch9
  6. Drobny J. G., 2014, Handbook of Thermoplastic Elastomers, Ch10
  7. Drobny J. G., 2014, Handbook of Thermoplastic Elastomers, Ch11

Cited by

See all 29

Metadata

Authors
Gao, C., Poon, K. C., Concilio, M., Zinn, T., Gregory, G. L., & Williams, C. K.
Affiliations
  • University of Oxford (GB)
  • Diamond Light Source (GB)
Corresponding author
Williams, Charlotte K.
Venue
Advanced Materials
Publisher
Wiley
Published
2025-04-16
Volume
37
Issue
27
Pages
e2416674-e2416674
ISSN
  • 0935-9648 (ISSN-L)
  • 1521-4095
OpenAlex
W4409507961
Cited by
26
References
79
Citations by year
2026: 20 · 2025: 6
FWCI
6.00
Type
journal article
Language
en
Open access
Locations
  • Advanced Materials (publishedVersion, cc-by)
  • PubMed Central (publishedVersion, cc-by)
  • PubMed (publishedVersion)
Funders
Engineering and Physical Sciences Research Council (EP/S023828/1, EP/Z532782/1, EP/S018603/1)
Topics
  • Physical Sciences › Materials Science › Polymers and Plastics › Polymer composites and self-healing
  • Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
  • Physical Sciences › Materials Science › Polymers and Plastics › Polymer crystallization and properties
Keywords
recyclable elastomers, strain-induced crystallization, tensile strength, elongation at break, elastic recovery, thermomechanical properties, creep resistance, moisture resistance, thermal stability

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.