An experimental investigation on frosting characteristics of a microchannel outdoor heat exchanger in an air conditioning heat pump system for electric vehicles
Abstract
To increase the driving range of electric vehicles in cold climate, air conditioning heat pump (ACHP) system is supposed to be the most effective solution. Working near 0°C with high humidity, the microchannel outdoor heat exchanger (OHX) in system would experience badly frosting process, like traditional residential heat pump system. It would lead to a significant reduction of system performance without defrosting in time. In this article, experimental investigation has been implemented on the frosting process of ACHP system of electric vehicles which is with a microchannel OHX. The phenomenon of frosting distribution was observed, the frosted part on surface shows uneven with various flows paths. The typical frosting characteristics of an outdoor microchannel heat exchanger were also obtained. In a self-designed three-heat exchanger ACHP system, the inlet and outlet refrigerant temperature of OHX as well as the outlet air temperature of system decrease with increasing frosting coverage rate. The frosting phenomenon was analyzed with variation of ambient temperature and humidity. System influence by frosting was also studied with under different ambient conditions. When OHX begins to frost, the heating capacity reduction of system under different ambient conditions were both increased but the differences in the coefficient of performance (COP) variations under different ambient conditions were small as frosting progressed.
Integrity signals
Registry
Cites
Statistics
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
Refrigerant distribution was always uneven, resulting in an uneven distribution of the frost layer on the surface of the heat exchanger.
“The refrigerant distribution was always uneven, resulting in an uneven distribution of the frost layer on the surface of the heat exchanger, as shown in Fig. 4 (a).”
Cites
Frost deposition on cold surfaces
Brian, P. L. T., Reid, R. C., & Shah, Y. T. (1970) · Industrial & Engineering Chemistry Fundamentals · doi:10.1021/i160035a013 · Cited by 142 · see citing works
(1967) · ASHRAE winter conference papers · Cited by 128 · see citing works
Mesoscale investigation of frost formation on a cold surface
Wu, X., Dai, W., Xu, W., & Tang, L. (2007) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2006.11.002 · Cited by 118 · see citing works
Shao, L.-L., Yang, L., & Zhang, C.-L. (2010) · Applied Energy · doi:10.1016/j.apenergy.2009.08.021 · Cited by 112 · see citing works
Introduction of a basic comfort equation
Fanger, P. O. (1967) · ASHRAE winter conference papers · Cited by 101 · see citing works
Phase change mass transfer model for frost growth and densification
Wu, X., Ma, Q., Chu, F., & Hu, S. (2016) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2016.01.018 · Cited by 100 · see citing works
Dynamic Melting of Freezing Droplets on Ultraslippery Superhydrophobic Surfaces
Chu, F., Wu, X., & Wang, L. (2017) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.6b16803 · Cited by 94 · see citing works
Frosting model based on phase change driving force
Wu, X.-M., Chu, F., & Ma, Q. (2017) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2017.03.081 · Cited by 94 · see citing works
Chung, Y., Yoo, J. W., Kim, G. T., & Kim, M. S. (2019) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2018.10.085 · Cited by 81 · cited 1× · see citing works
“The model can be applied to foresee the frosting layer growth speed and performance variations of the heat pump system.(9) With the development of heat exchanger technology, there are many experimental studies on the frosting characteristics of heat exchangers under different working conditions.”
MethodSong, M., Deng, S., Mao, N., & Ye, X. (2016) · Applied Energy · doi:10.1016/j.apenergy.2015.12.107 · Cited by 81 · see citing works
Measurement and Correlation of Water Frost Thermal Conductivity and Density
Biguria, G., & Wenzel, L. A. (1970) · Industrial & Engineering Chemistry Fundamentals · doi:10.1021/i160033a021 · Cited by 75 · see citing works
Experimental study of frost formation on cold surfaces with various fin layouts
Wu, X., Hu, S., & Chu, F. (2016) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2015.11.045 · Cited by 72 · see citing works
Xu, B., Zhang, C., Wang, Y., Chen, J., Xu, K., Li, F., & Wang, N. (2015) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2015.06.037 · Cited by 69 · see citing works
Zhang, L., Jiang, Y., Dong, J., Yao, Y., & Deng, S. (2019) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.09.016 · Cited by 65 · see citing works
Shen, Y., Jin, M., Wu, X., Tao, J., Luo, X., Chen, H., Yang, L. L., & Xie, Y. (2019) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2019.04.052 · Cited by 63 · see citing works
Moallem, E., Hong, T., Cremaschi, L., & Fisher, D. E. (2013) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2012.09.009 · Cited by 57 · see citing works
Dynamic Defrosting on Scalable Superhydrophobic Surfaces
Murphy, K. R., McClintic, W. T., Lester, K., Collier, C. P., & Boreyko, J. B. (2017) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.7b05651 · Cited by 55 · see citing works
(2015) · doi:10.1016/j.expthermflusci.2014.10.006 · Cited by 47 · see citing works
Experimental investigation of frost retardation for superhydrophobic surface using a luminance meter
Kim, D., Kim, H., Kim, S. W., Kim, D. R., & Lee, K.-S. (2015) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2015.04.042 · Cited by 46 · see citing works
Heu, C. S., Kim, S. W., Kim, J., Lee, S., Kim, J. M., Lee, K.-S., & Kim, D. R. (2018) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.04.146 · Cited by 45 · see citing works
Tan, H., Tao, T., Xu, G., Zhang, S., Wang, D., & Luo, X. (2013) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2013.10.006 · Cited by 43 · see citing works
Numerical Simulation of Frosting on Fin-and-Tube Heat Exchanger Surfaces
Wu, X., Ma, Q., & Chu, F. (2017) · Journal of Thermal Science and Engineering Applications · doi:10.1115/1.4035925 · Cited by 42 · cited 1× · see citing works
“The results show that the frosting model can be applied to forecast frost layer growth on the surfaces of heat exchanger and it was verified by experiments.(16) Han et al(17) studied the frost characteristic of a finned tube heat exchanger from −18 C to 6 C and brought forth a new term “frosting factor”.”
MethodZhang, L., Jiang, Y., Dong, J., Yao, Y., & Deng, S. (2019) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2019.114063 · Cited by 40 · see citing works
Heat and Mass Transfer to a Cryosurface in Free Convection
Barron, R. F., & Han, L. S. (1965) · Journal of Heat Transfer · doi:10.1115/1.3689144 · Cited by 37 · see citing works
Feng, W., Liang, C.-H., Zhang, X., & Zhang, Y. (2018) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2018.01.022 · Cited by 32 · see citing works
Liang, C., Wang, F., Lu, Y. L., Yang, M., & Zhang, X. (2015) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2015.10.015 · Cited by 32 · see citing works
Frost behavior of a louvered fin heat exchanger with vortex-generating fins
Park, J.-S., Byun, S., Kim, D. R., & Lee, K.-S. (2017) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2017.06.090 · Cited by 24 · see citing works
Experimental study of the characteristic of frosting on low-temperature air cooler
Haijie, Q., Li, W., Bo, D., Zhihai, Z., & Weiying, Z. (2014) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2014.02.021 · Cited by 22 · see citing works
Visualization and measurement of reverse flow in an actual channel of a microchannel evaporator
Li, H., & Hrnjak, P. (2017) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2017.01.085 · Cited by 19 · see citing works
Han, X., Fan, W., Qu, M., Chen, J., & Chen, Q. (2014) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2014.03.011 · Cited by 15 · see citing works
Experimental Study of Frost Growth Characteristics on Surface of Fin-tube Heat Exchanger
Liping, X., Xianmin, G., & Xing, Z. (2017) · Energy Procedia · doi:10.1016/j.egypro.2017.03.1039 · Cited by 13 · see citing works
Numerical Simulation of Frosting on Wavy Fin-and-tube Heat Exchanger Surfaces
Ma, Q., Wu, X.-M., Chu, F., & Zhu, B. (2017) · Journal of Physics Conference Series · doi:10.1088/1742-6596/891/1/012052 · Cited by 10 · see citing works
Flagged first, then by citations
Cited by
Sorted by citations
Xiong, T., Liu, G., Huang, S., Yan, G. F., & Yu, J. (2021) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2021.117820 · Cited by 66 · see citing works
Self-citationReview of heat pump integrated energy systems for future zero-emission vehicles
Zhang, N., Lu, Y., Ouderji, Z. H., & Yu, Z. (2023) · Energy · doi:10.1016/j.energy.2023.127101 · Cited by 57 · see citing works
Ko, J., & Jeong, J. H. (2024) · Applied Energy · doi:10.1016/j.apenergy.2024.124095 · Cited by 42 · see citing works
Mousaei, A., Gheisarnejad, M., & Khooban, M. H. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.108860 · Cited by 37 · see citing works
Li, F., Wu, S., Ma, Z., Zhao, R., & Huang, D. (2022) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2022.118220 · Cited by 36 · see citing works
Malik, A., Khan, S. A., & Lazoglu, I. (2021) · International journal of refrigeration · doi:10.1016/j.ijrefrig.2021.07.032 · Cited by 31 · see citing works
Xiong, T., Liu, G., Gao, Q., Yan, G., & Yu, J. (2023) · Journal of Building Engineering · doi:10.1016/j.jobe.2022.105654 · Cited by 26 · see citing works
Self-citationPreparation and Anti-frost Performance of PDMS-SiO2/SS Superhydrophobic Coating
Jia, L., Sun, J., Li, X., Zhang, X., Chen, L., & Tian, X. (2020) · Coatings · doi:10.3390/coatings10111051 · Cited by 22 · see citing works
Chen, J., Wu, J., He, J., & Guo, Z. (2022) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2021.11.008 · Cited by 20 · see citing works
Peng, D., Xiaoyonga, G., Wang, Y., Jiacheng, X., Mengqiang, S., & Li, K. (2023) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2023.121352 · Cited by 18 · see citing works
Self-citationLuo, B., Li, F., Wu, S., Shi, K., Ding, Y., Zhao, R., Huang, D., & Shi, W. (2025) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2025.01.030 · Cited by 11 · see citing works
Frost detection in CO₂ heat pump systems using image recognition and performance metrics
Gu, P., Li, K., Li, X., Chen, X., Zhang, H., Yan, J., He, Q., Song, L., Li, C., Mahian, O., et al. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.129395 · Cited by 1 · see citing works
Self-citationWu, S., Wang, G., Li, F., Shi, K., Zhao, R., Huang, D. J., & Zhao, Y. (2026) · Energy Storage and Saving · doi:10.1016/j.enss.2026.02.001 · Cited by 1 · see citing works
- Authors
- Li, K., Luo, S., Yu, J., Tang, Q., Su, L., & Fang, Y.
- Affiliations
- University of Shanghai for Science and Technology (CN)
- SAIC Motor (China) (CN)
- Corresponding author
- Yu, Jun
- Venue
- International Journal of Energy Research
- Publisher
- Wiley
- Published
- 2020-05-05
- Volume
- 44
- Issue
- 9
- Pages
- 7807-7819
- ISSN
- 0363-907X (ISSN-L)
- 1099-114X
- OpenAlex
- W3022173272
- Cited by
- 13
- References
- 32
- Citations by year
- 2026: 1 · 2025: 2 · 2024: 1 · 2023: 3 · 2022: 2 · 2021: 3 · 2020: 1
- FWCI
- 1.11
- Type
- journal article
- Language
- en
- Open access
- closed
- Licence
- Locations
- International Journal of Energy Research (publishedVersion)
- Funders
- Capacity Building Plan for some Non-military Universities and Colleges of Shanghai Scientific Committee (18060502600)
- National Nature Science Foundation of China (51876130, 51906158)
- Shanghai Sailing Program (18YF1417900)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Refrigeration and Air Conditioning Technologies
- Physical Sciences › Engineering › Mechanical Engineering › Heat Transfer and Optimization
- Physical Sciences › Engineering › Aerospace Engineering › Icing and De-icing Technologies
- Keywords
- frost formation, microchannel heat exchangers, outdoor heat exchanger, electric vehicles, coefficient of performance, air humidity, ambient temperature, thawing
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
