The DOI matches its Crossref record; 82 of the 82 references it cites were found in a registry or an index.
Laser and electron‐beam powder‐bed additive manufacturing of metallic implants: A review on processes, materials and designs
Open accessAbstract
Additive manufacturing (AM), also commonly known as 3D printing, allows the direct fabrication of functional parts with complex shapes from digital models. In this review, the current progress of two AM processes suitable for metallic orthopaedic implant applications, namely selective laser melting (SLM) and electron beam melting (EBM) are presented. Several critical design factors such as the need for data acquisition for patient‐specific design, design dependent porosity for osteo‐inductive implants, surface topology of the implants and design for reduction of stress‐shielding in implants are discussed. Additive manufactured biomaterials such as 316L stainless steel, titanium‐6aluminium‐4vanadium (Ti6Al4V) and cobalt‐chromium (CoCr) are highlighted. Limitations and future potential of such technologies are also explored. © 2015 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 34:369–385, 2016.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
A study of the microstructural evolution during selective laser melting of Ti–6Al–4V
Thijs, L., Verhaeghe, F., Craeghs, T., Humbeeck, J. V., & Kruth, J.-P. (2010) · Acta Materialia · doi:10.1016/j.actamat.2010.02.004 · Cited by 2,929
The design of scaffolds for use in tissue engineering. Part I. Traditional factors
Yang, S., Leong, K.-F., Du, Z., & Chua, C.-K. (2001) · Tissue Engineering · doi:10.1089/107632701753337645 · Cited by 2,234
Vrancken, B., Thijs, L., Kruth, J.-P., & Van Humbeeck, J. (2012) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2012.07.022 · Cited by 1,896
Binding mechanisms in selective laser sintering and selective laser melting
Kruth, J., Mercelis, P., Van Vaerenbergh, J., Froyen, L., & Rombouts, M. (2005) · Rapid Prototyping Journal · doi:10.1108/13552540510573365 · Cited by 1,383
Murr, L. E., Quinones, S. A., Gaytan, S. M., Lopez, M. I., Rodela, A., Martinez, E. Y., Hernandez, D. H., Martinez, E., Medina, F., & Wicker, R. B. (2009) · Journal of the Mechanical Behavior of Biomedical Materials · doi:10.1016/j.jmbbm.2008.05.004 · Cited by 997
Rafi, H. K., Karthik, N. V., Gong, H., Starr, T. L., & Stucker, B. E. (2013) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-013-0658-0 · Cited by 987
Selective laser melting of biocompatible metals for rapid manufacturing of medical parts
Vandenbroucke, B., & Kruth, J. (2007) · Rapid Prototyping Journal · doi:10.1108/13552540710776142 · Cited by 981
Mechanical evaluation of porous titanium (Ti6Al4V) structures with electron beam melting (EBM)
Parthasarathy, J., Starly, B., Raman, S., & Christensen, A. (2010) · Journal of the Mechanical Behavior of Biomedical Materials · doi:10.1016/j.jmbbm.2009.10.006 · Cited by 816
Rapid prototyping in tissue engineering: challenges and potential
Yeong, W.-Y., Chua, C.-K., Leong, K.-F., & Chandrasekaran, M. (2004) · Trends in Biotechnology · doi:10.1016/j.tibtech.2004.10.004 · Cited by 807
Self-citationVan Bael, S., Chai, Y. C., Truscello, S., Moesen, M., Kerckhofs, G., Van Oosterwyck, H., Kruth, J.-P., & Schrooten, J. (2012) · Acta Biomaterialia · doi:10.1016/j.actbio.2012.04.001 · Cited by 766
Evaluations of cellular lattice structures manufactured using selective laser melting
Yan, C., Hao, L., Hussein, A., & Raymont, D. (2012) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2012.06.002 · Cited by 730
The Design of Scaffolds for Use in Tissue Engineering. Part II. Rapid Prototyping Techniques
Yang, S., Leong, K.-F., Du, Z., & Chua, C.-K. (2002) · Tissue Engineering · doi:10.1089/107632702753503009 · Cited by 729
Thijs, L., Montero Sistiaga, M. L., Wauthle, R., Xie, Q., Kruth, J.-P., & Van Humbeeck, J. (2013) · Acta Materialia · doi:10.1016/j.actamat.2013.04.036 · Cited by 672
Yan, C., Hao, L., Hussein, A., Young, P., & Raymont, D. (2014) · Materials & Design · doi:10.1016/j.matdes.2013.10.027 · Cited by 622
Spierings, A. B., Herres, N., & Levy, G. (2011) · Rapid Prototyping Journal · doi:10.1108/13552541111124770 · Cited by 614
Manufacture by selective laser melting and mechanical behavior of a biomedical Ti–24Nb–4Zr–8Sn alloy
Zhang, L., Klemm, D., Eckert, J., Hao, Y., & Sercombe, T. B. (2011) · Scripta Materialia · doi:10.1016/j.scriptamat.2011.03.024 · Cited by 597
Murr, L. E., Esquivel, E. V., Quinones, S. A., Gaytan, S. M., Lopez, M. I., Martinez, E. Y., Medina, F., Hernandez, D. H., Martinez, E., Martinez, J. L., et al. (2009) · Materials Characterization · doi:10.1016/j.matchar.2008.07.006 · Cited by 564
Metallic Scaffolds for Bone Regeneration
Alvarez, K., & Nakajima, H. (2009) · Materials · doi:10.3390/ma2030790 · Cited by 505
Takaichi, A., Suyalatu, Nakamoto, T., Joko, N., Nomura, N., Tsutsumi, Y., Migita, S., Doi, H., Kurosu, S., Chiba, A., et al. (2013) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2013.01.021 · Cited by 489
Tolosa, I., Garciandía, F., Zubiri, F., Zapirain, F., & Esnaola, A. (2010) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-010-2631-5 · Cited by 487
Wauthle, R., Vrancken, B., Beynaerts, B., Jorissen, K., Schrooten, J., Kruth, J.-P., & Van Humbeeck, J. (2015) · Additive Manufacturing · doi:10.1016/j.addma.2014.12.008 · Cited by 463
Osteoinductive biomaterials—properties and relevance in bone repair
Habibovic, P., & de Groot, K. (2007) · Journal of Tissue Engineering and Regenerative Medicine · doi:10.1002/term.5 · Cited by 455
Amin Yavari, S., Ahmadi, S. M., Wauthle, R., Pouran, B., Schrooten, J., Weinans, H., & Zadpoor, A. A. (2015) · Journal of the Mechanical Behavior of Biomedical Materials · doi:10.1016/j.jmbbm.2014.12.015 · Cited by 431
Fatigue performance of additive manufactured metallic parts
Spierings, A. B., Starr, T. L., & Wegener, K. (2013) · Rapid Prototyping Journal · doi:10.1108/13552541311302932 · Cited by 426
Microstructure and mechanical behaviour of Ti―6Al―7Nb alloy produced by selective laser melting
Chlebus, E., Kuźnicka, B., Kurzynowski, T., & Dybała, B. (2011) · Materials Characterization · doi:10.1016/j.matchar.2011.03.006 · Cited by 423
Liu, Z. H., Zhang, D. Q., Sing, S. L., Chua, C. K., & Loh, L. E. (2014) · Materials Characterization · doi:10.1016/j.matchar.2014.05.001 · Cited by 415
Self-citationWiria, F. E., Leong, K. F., Chua, C. K., & Liu, Y. (2007) · Acta Biomaterialia · doi:10.1016/j.actbio.2006.07.008 · Cited by 405
Self-citationMechanical properties of open-cell metallic biomaterials manufactured using additive manufacturing
Campoli, G., Borleffs, M. S., Amin Yavari, S., Wauthle, R., Weinans, H., & Zadpoor, A. A. (2013) · Materials & Design · doi:10.1016/j.matdes.2013.01.071 · Cited by 404
Pattanayak, D. K., Fukuda, A., Matsushita, T., Takemoto, M., Fujibayashi, S., Sasaki, K., Nishida, N., Nakamura, T., & Kokubo, T. (2011) · Acta Biomaterialia · doi:10.1016/j.actbio.2010.09.034 · Cited by 384
Yasa, E., Deckers, J., & Kruth, J. (2011) · Rapid Prototyping Journal · doi:10.1108/13552541111156450 · Cited by 371
Yan, C., Hao, L., Hussein, A., Bubb, S. L., Young, P., & Raymont, D. (2014) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2013.12.004 · Cited by 362
Yeong, W. Y., Sudarmadji, N., Yu, H. Y., Chua, C. K., Leong, K. F., Venkatraman, S. S., Boey, Y. C. F., & Tan, L. P. (2010) · Acta Biomaterialia · doi:10.1016/j.actbio.2009.12.033 · Cited by 355
Self-citationCranial reconstruction: 3D biomodel and custom-built implant created using additive manufacturing
Jardini, A. L., Larosa, M. A., Filho, R. M., Zavaglia, C. A. D. C., Bernardes, L. F., Lambert, C. S., Calderoni, D. R., & Kharmandayan, P. (2014) · Journal of Cranio-Maxillofacial Surgery · doi:10.1016/j.jcms.2014.07.006 · Cited by 350
Osteoinduction of porous Ti implants with a channel structure fabricated by selective laser melting
Fukuda, A., Takemoto, M., Saito, T., Fujibayashi, S., Neo, M., Pattanayak, D. K., Matsushita, T., Sasaki, K., Nishida, N., Kokubo, T., et al. (2011) · Acta Biomaterialia · doi:10.1016/j.actbio.2011.01.037 · Cited by 349
Microstructure and mechanical behavior of porous Ti–6Al–4V parts obtained by selective laser melting
Sallica-Leva, E., Jardini, A. L., & Fogagnolo, J. B. (2013) · Journal of the Mechanical Behavior of Biomedical Materials · doi:10.1016/j.jmbbm.2013.05.011 · Cited by 340
Cheng, X. Y., Li, S. J., Murr, L. E., Zhang, Z. B., Hao, Y. L., Yang, R., Medina, F., & Wicker, R. B. (2012) · Journal of the Mechanical Behavior of Biomedical Materials · doi:10.1016/j.jmbbm.2012.10.005 · Cited by 329
Delgado, J., Ciurana, J., & Rodríguez, C. A. (2012) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-011-3643-5 · Cited by 305
Warnke, P. H., Douglas, T., Wollny, P., Sherry, E., Steiner, M., Galonska, S., Becker, S. T., Springer, I. N., Wiltfang, J., & Sivananthan, S. (2009) · Tissue Engineering Part C: Methods · doi:10.1089/ten.tec.2008.0288 · Cited by 305
Osteoblastic cell behaviour on different titanium implant surfaces
Le Guehennec, L., Lopez-Heredia, M.-A., Enkel, B., Weiss, P., Amouriq, Y., & Layrolle, P. (2008) · Acta Biomaterialia · doi:10.1016/j.actbio.2007.12.002 · Cited by 293
Facchini, L., Magalini, E., Robotti, P., & Molinari, A. (2009) · Rapid Prototyping Journal · doi:10.1108/13552540910960262 · Cited by 290
Van der Stok, J., Van der Jagt, O. P., Amin Yavari, S., De Haas, M. F. P., Waarsing, J. H., Jahr, H., Van Lieshout, E. M. M., Patka, P., Verhaar, J. A. N., Zadpoor, A. A., et al. (2013) · Journal of Orthopaedic Research · doi:10.1002/jor.22293 · Cited by 271
Chua, C. K., & Leong, K. F. (2014) · WORLD SCIENTIFIC eBooks · doi:10.1142/9008 · Cited by 261
Karlsson, J., Snis, A., Engqvist, H., & Lausmaa, J. (2013) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2013.06.010 · Cited by 254
316L Stainless Steel with Gradient Porosity Fabricated by Selective Laser Melting
Li, R., Liu, J., Shi, Y., Du, M., & Xie, Z. (2010) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-009-9535-2 · Cited by 247
Sing, S. L., Lam, L. P., Zhang, D. Q., Liu, Z. H., & Chua, C. K. (2015) · Materials Characterization · doi:10.1016/j.matchar.2015.07.007 · Cited by 238
Self-citationSudarmadji, N., Tan, J. Y., Leong, K. F., Chua, C. K., & Loh, Y. T. (2011) · Acta Biomaterialia · doi:10.1016/j.actbio.2010.09.024 · Cited by 220
Microstructure and mechanical properties of selective laser melted magnesium
Ng, C. C., Savalani, M. M., Lau, M. L., & Man, H. C. (2011) · Applied Surface Science · doi:10.1016/j.apsusc.2011.03.004 · Cited by 208
Compression‐compression fatigue of selective electron beam melted cellular titanium (Ti‐6Al‐4V)
Hrabe, N. W., Heinl, P., Flinn, B., Körner, C., & Bordia, R. K. (2011) · Journal of Biomedical Materials Research Part B: Applied Biomaterials · doi:10.1002/jbm.b.31901 · Cited by 203
Lin, C., Wirtz, T., LaMarca, F., & Hollister, S. J. (2007) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.31231 · Cited by 198
Medical design: Direct metal laser sintering of Ti–6Al–4V
Bertol, L. S., Júnior, W. K., Silva, F. P. D., & Aumund-Kopp, C. (2010) · Materials & Design · doi:10.1016/j.matdes.2010.02.050 · Cited by 193
Development and mechanical characterization of porous titanium bone substitutes
Barbas, A., Bonnet, A.-S., Lipinski, P., Pesci, R., & Dubois, G. (2012) · Journal of the Mechanical Behavior of Biomedical Materials · doi:10.1016/j.jmbbm.2012.01.008 · Cited by 180
In vivo performance of selective electron beam‐melted Ti‐6Al‐4V structures
Ponader, S., von Wilmowsky, C., Widenmayer, M., Lutz, R., Heinl, P., Körner, C., Singer, R. F., Nkenke, E., Neukam, F. W., & Schlegel, K. A. (2010) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.32337 · Cited by 179
Muller, P., Mognol, P., & Hascoët, J.-Y. (2012) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2012.11.020 · Cited by 156
Shape deposition manufacturing of heterogeneous structures
Weiss, L. E., Merz, R., Prinz, F. B., et al. (1997) · Journal of Manufacturing Systems · doi:10.1016/s0278-6125(97)89095-4 · Cited by 148
Cheah, C. M., Chua, C. K., Leong, K. F., & Chua, S. W. (2003) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s001700300035 · Cited by 145
Palmquist, A., Snis, A., Emanuelsson, L., Browne, M., & Thomsen, P. (2011) · Journal of Biomaterials Applications · doi:10.1177/0731684411431857 · Cited by 144
Customised titanium implant fabricated in additive manufacturing for craniomaxillofacial surgery
Jardini, A. L., Larosa, M. A., Zavaglia, C. A. D. C., Bernardes, L. F., Lambert, C. S., Kharmandayan, P., Calderoni, D. R., & Filho, R. M. (2014) · Virtual and Physical Prototyping · doi:10.1080/17452759.2014.900857 · Cited by 131
Thomsen, P., Malmström, J., Emanuelsson, L., René, M., & Snis, A. (2008) · Journal of Biomedical Materials Research Part B Applied Biomaterials · doi:10.1002/jbm.b.31250 · Cited by 131
Kim, K.-B., Kim, W., Kim, H., & Kim, J. (2013) · Dental Materials · doi:10.1016/j.dental.2013.04.007 · Cited by 129
A novel root analogue dental implant using CT scan and CAD/CAM: selective laser melting technology
Figliuzzi, M. M., Mangano, F. G., & Mangano, C. (2012) · International Journal of Oral and Maxillofacial Surgery · doi:10.1016/j.ijom.2012.01.014 · Cited by 114
Characteristics of the bond in Cu–H13 tool steel parts fabricated using SLM
Al-Jamal, O. M., Hinduja, S., & Li, L. (2008) · CIRP Annals · doi:10.1016/j.cirp.2008.03.010 · Cited by 106
Rapid manufacture of custom‐fitting surgical guides
Bibb, R., Eggbeer, D., Evans, P. L., Bocca, A. P., & Sugar, A. (2009) · Rapid Prototyping Journal · doi:10.1108/13552540910993879 · Cited by 103
Multi-material metallic structure fabrication using electron beam melting
Terrazas, C. A., Gaytan, S. M., Rodriguez, E., Espalin, D., Murr, L. E., Medina, F. R., & Wicker, R. B. (2013) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-013-5449-0 · Cited by 101
Zhang, Z., Jones, D. H., Yue, S., Lee, P. D., Jones, J. R., Sutcliffe, C. J., & Jones, E. (2013) · Materials Science and Engineering C · doi:10.1016/j.msec.2013.05.050 · Cited by 96
Yang, Y., Lu, J., Luo, Z., & Wang, D. (2012) · Rapid Prototyping Journal · doi:10.1108/13552541211272027 · Cited by 94
Sanz, C., & Navas, V. G. (2013) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2013.06.013 · Cited by 93
Development of highly porous titanium scaffolds by selective laser melting
Wang, Y., Shen, Y., Wang, Z., Yang, J., Liu, N., & Wenrong, H. (2010) · Materials Letters · doi:10.1016/j.matlet.2009.12.035 · Cited by 87
Mazzoli, A., Germani, M., & Raffaeli, R. (2008) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2008.11.013 · Cited by 86
Electron Beam Melting Fabrication of Porous Ti6Al4V Scaffolds: Cytocompatibility and Osteogenesis
Lv, J., Jia, Z., Li, J., Wang, Y., Yang, J., Xiu, P., Zhang, K., Cai, H., & Liu, Z. (2015) · Advanced Engineering Materials · doi:10.1002/adem.201400508 · Cited by 84
Biemond, J., Hannink, G., Verdonschot, N. J. J., & Buma, P. (2012) · Journal of Materials Science Materials in Medicine · doi:10.1007/s10856-012-4836-7 · Cited by 83
Abe, F., Santos, E. C., Kitamura, Y., Osakada, K., & Shiomi, M. (2003) · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · doi:10.1243/095440603762554668 · Cited by 81
Implant design and production—a new approach by selective laser melting
Wehmöller, M., Warnke, P. H., Zilian, C., & Eufinger, H. (2005) · International Congress Series · doi:10.1016/j.ics.2005.03.155 · Cited by 70
Manufacture of Co-Cr dental crowns and bridges by selective laser Melting technology
Averyanova, M., Bertrand, P., & Verquin, B. (2011) · Virtual and Physical Prototyping · doi:10.1080/17452759.2011.619083 · Cited by 61
Annealing of Co-Cr dental alloy: effects on nanostructure and Rockwell hardness
Ayyıldız, S., Soylu, E. H., İde, S., Kılıç, S., Sipahi, C., Pişkin, B., & Gökçe, H. S. (2013) · The Journal of Advanced Prosthodontics · doi:10.4047/jap.2013.5.4.471 · Cited by 55
Xiao, D., Yang, Y., Su, X., Wang, D., & Sun, J. (2013) · Bio-Medical Materials and Engineering · doi:10.3233/bme-130765 · Cited by 51
Szymczyk‐Ziółkowska, P., Junka, A., Ziółkowski, G., Smutnicka, D., Bartoszewicz, M., & Chlebus, E. (2013) · PubMed · doi:10.5277/abb130109 · Cited by 38
Hrabe, N. W., Heinl, P., Bordia, R. K., Körner, C., & Fernandes, R. J. (2013) · Connective Tissue Research · doi:10.3109/03008207.2013.822864 · Cited by 37
de Oyagüe, R. C., Turrión, A. S., Lozano, J. F. L., Montero, J., Albaladejo, A., & Suárez, M. J. (2011) · Odontology · doi:10.1007/s10266-011-0050-1 · Cited by 36
Marcu, T., Todea, M., Maines, L., Leordean, D., Berce, P., & Popa, C. O. (2012) · Powder Metallurgy · doi:10.1179/1743290112y.0000000007 · Cited by 34
Dental root implants produced by the combined selective laser sintering/melting of titanium powders
Толочко, Н. К., Savich, V. V., Laoui, T., et al. (2002) · Proceedings of the Institution of Mechanical Engineers Part L Journal of Materials Design and Applications · doi:10.1177/146442070221600406 · Cited by 31
Venugopal, S., Vasudevan, M., Venugopal, S., Sivaprasad, P. V., Jha, S. K., Pandey, P., Mannan, S. L., & Prasad, Y. V. R. K. (1996) · Materials Science and Technology · doi:10.1179/026708396790122143 · Cited by 14
Cited by
Wu, B., Pan, Z., Ding, D., Cuiuri, D., Li, H., Xu, J., & Norrish, J. (2018) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2018.08.001 · Cited by 1,577
Kok, Y., Tan, X. P., Wang, P., Nai, M. L. S., Loh, N. H., Liu, E., & Tor, S. B. (2018) · Materials & Design · doi:10.1016/j.matdes.2017.11.021 · Cited by 1,447
Zhang, J., Song, B., Wei, Q., Bourell, D., & Shi, Y. (2019) · Journal of Materials Science & Technology · doi:10.1016/j.jmst.2018.09.004 · Cited by 1,205
Sanaei, N., & Fatemi, A. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100724 · Cited by 1,029
Mechanical Metamaterials and Their Engineering Applications
Surjadi, J. U., Gao, L., Du, H., Li, X., Xiong, X., Fang, N. X., & Lu, Y. (2019) · Advanced Engineering Materials · doi:10.1002/adem.201800864 · Cited by 982
Metadata
- Authors
- Sing, S. L., An, J., Yeong, W. Y., & Wiria, F. E.
- Venue
- Journal of Orthopaedic Research
- Publisher
- Wiley
- Published
- 2015-10-29
- Volume
- 34
- Issue
- 3
- Pages
- 369-385
- ISSN
- 0736-0266 (ISSN-L)
- 1554-527X
- OpenAlex
- W2112042205
- Cited by
- 942
- References
- 82
- FWCI
- 58.84
- Type
- journal article
- Language
- en
- Open access
- bronze
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.