The DOI matches its Crossref record; 107 of the 107 references it cites were found in a registry or an index.
An overview of powder granulometry on feedstock and part performance in the selective laser melting process
Open accessAbstract
Abstract Metal Additive Manufacturing (AM) has begun its revolution in various high value industry sectors through enabling design freedom and alleviating laborious machining operations during the production of geometrically complex components. The use of powder bed fusion (PBF) techniques such as Selective Laser Melting (SLM) also promotes material efficiency where unfused granular particles are recyclable after each forming operation in contrast to conventional subtractive methods. However, powder characteristics tend to deviate from their pre-process state following different stages of the process which could affect feedstock behaviour and final part quality. In particular, primary feedstock characteristics including granulometry and morphology must be tightly controlled due to their influence on powder flow and packing behaviour as well as other corresponding attributes which altogether affect material deposition and subsequent laser consolidation. Despite ongoing research efforts which focused strongly on driving process refinement steps to optimise the SLM process, it is also critical to understand the level of material sensitivity towards part forming due to granulometry changes and tackle various reliability as well as quality issues related to powder variation in order to further expand the industrial adoption of the metal additive technique. In this review, the current progress of Metal AM feedstock and various powder characteristics related to the Selective Laser Melting process will be addressed, with a focus on the influence of powder granulometry on feedstock and final part properties.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
III. An essay on the cohesion of fluids
Young, T. (1805) · Philosophical Transactions of the Royal Society of London · doi:10.1098/rstl.1805.0005 · Cited by 6,643
Additive manufacturing of metals
Herzog, D., Seyda, V., Wycisk, E., & Emmelmann, C. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.07.019 · Cited by 4,759
Flash Method of Determining Thermal Diffusivity, Heat Capacity, and Thermal Conductivity
Parker, W. J., Jenkins, R. J., Butler, C. P., & Abbott, G. L. (1961) · Journal of Applied Physics · doi:10.1063/1.1728417 · Cited by 3,978
Laser additive manufacturing of metallic components: materials, processes and mechanisms
Gu, D. D., Meiners, W., Wissenbach, K., & Poprawe, R. (2012) · International Materials Reviews · doi:10.1179/1743280411y.0000000014 · Cited by 3,197
A study of the microstructural evolution during selective laser melting of Ti–6Al–4V
Thijs, L., Verhaeghe, F., Craeghs, T., Humbeeck, J. V., & Kruth, J.-P. (2010) · Acta Materialia · doi:10.1016/j.actamat.2010.02.004 · Cited by 2,929
The metallurgy and processing science of metal additive manufacturing
Sames, W. J., List, F. A., Pannala, S., Dehoff, R. R., & Babu, S. S. (2016) · International Materials Reviews · doi:10.1080/09506608.2015.1116649 · Cited by 2,529
Review of selective laser melting: Materials and applications
Yap, C. Y., Chua, C. K., Dong, Z. L., Liu, Z. H., Zhang, D. Q., Loh, L. E., & Sing, S. L. (2015) · Applied Physics Reviews · doi:10.1063/1.4935926 · Cited by 2,353
Residual stresses in selective laser sintering and selective laser melting
Mercelis, P., & Kruth, J. (2006) · Rapid Prototyping Journal · doi:10.1108/13552540610707013 · Cited by 2,015
Vrancken, B., Thijs, L., Kruth, J.-P., & Van Humbeeck, J. (2012) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2012.07.022 · Cited by 1,896
Characterization of Porous Solids and Powders: Surface Area, Pore Size and Density
Lowell, S., Shields, J. E., Thomas, M. A., & Thommes, M. (2004) · Particle Technology Series · doi:10.1007/978-1-4020-2303-3 · Cited by 1,824
Metal Additive Manufacturing: A Review of Mechanical Properties
Lewandowski, J. J., & Seifi, M. (2016) · Annual Review of Materials Research · doi:10.1146/annurev-matsci-070115-032024 · Cited by 1,722
Metal Fabrication by Additive Manufacturing Using Laser and Electron Beam Melting Technologies
Murr, L. E., Gaytan, S. M., Ramirez, D. A., Martinez, E., Hernandez, J., Amato, K. N., Shindo, P. W., Medina, F. R., & Wicker, R. B. (2012) · Journal of Materials Science & Technology · doi:10.1016/s1005-0302(12)60016-4 · Cited by 1,686
Characterization of porous solids and powders: surface area, pore size, and density
(2005) · Choice Reviews Online · doi:10.5860/choice.42-5288 · Cited by 1,637
Observation of keyhole-mode laser melting in laser powder-bed fusion additive manufacturing
King, W. E., Barth, H. D., Castillo, V. M., Gallegos, G. F., Gibbs, J. W., Hahn, D. E., Kamath, C., & Rubenchik, A. M. (2014) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2014.06.005 · Cited by 1,616
Selective laser melting of iron-based powder
Kruth, J. P., Froyen, L., Van Vaerenbergh, J., Mercelis, P., Rombouts, M., & Lauwers, B. (2004) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2003.11.051 · Cited by 1,550
Consolidation phenomena in laser and powder-bed based layered manufacturing
Kruth, J.-P., Levy, G., Klocke, F., & Childs, T. H. C. (2007) · CIRP Annals · doi:10.1016/j.cirp.2007.10.004 · Cited by 1,444
King, W. E., Anderson, A. T., Ferencz, R. M., Hodge, N. E., Kamath, C., Khairallah, S. A., & Rubenchik, A. M. (2015) · Applied Physics Reviews · doi:10.1063/1.4937809 · Cited by 1,258
Mechanical Packing of Spherical Particles
McGEARY, R. K. (1961) · Journal of the American Ceramic Society · doi:10.1111/j.1151-2916.1961.tb13716.x · Cited by 1,044
Gong, H., Rafi, K., Gu, H., Starr, T., & Stucker, B. (2014) · Additive Manufacturing · doi:10.1016/j.addma.2014.08.002 · Cited by 1,038
Mechanical behavior of additive manufactured, powder-bed laser-fused materials
Mower, T. M., & Long, M. J. (2016) · Materials Science and Engineering: A · doi:10.1016/j.msea.2015.10.068 · Cited by 1,001
Liverani, E., Toschi, S., Ceschini, L., & Fortunato, A. (2017) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2017.05.042 · Cited by 990
Selective laser melting of biocompatible metals for rapid manufacturing of medical parts
Vandenbroucke, B., & Kruth, J. (2007) · Rapid Prototyping Journal · doi:10.1108/13552540710776142 · Cited by 981
Selective laser melting of aluminium components
Louvis, E., Fox, P., & Sutcliffe, C. J. (2011) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2010.09.019 · Cited by 933
Single track formation in selective laser melting of metal powders
Yadroitsev, I., Gusarov, A., Yadroitsava, I., & Smurov, I. (2010) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2010.05.010 · Cited by 827
The microstructure and mechanical properties of deposited-IN718 by selective laser melting
Wang, Z., Guan, K., Gao, M., Li, X., Chen, X., & Zeng, X. (2012) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2011.10.107 · Cited by 812
Water adsorption and the wetting of metal surfaces
Hodgson, A., & Haq, S. (2009) · Surface Science Reports · doi:10.1016/j.surfrep.2009.07.001 · Cited by 775
Cherry, J. A., Davies, H. M., Mehmood, S., Lavery, N. P., Brown, S. G. R., & Sienz, J. (2015) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-014-6297-2 · Cited by 755
Balling behavior of stainless steel and nickel powder during selective laser melting process
Li, R., Liu, J., Shi, Y., Wang, L., & Jiang, W. (2012) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-011-3566-1 · Cited by 722
Selective laser melting of stainless steel 316L with low porosity and high build rates
Sun, Z., Tan, X., Tor, S. B., & Yeong, W. Y. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.05.035 · Cited by 714
Cleary, P. W., & Sawley, M. L. (2002) · Applied Mathematical Modelling · doi:10.1016/s0307-904x(01)00050-6 · Cited by 691
Gu, D., & Shen, Y. (2009) · Materials & Design · doi:10.1016/j.matdes.2009.01.013 · Cited by 672
Overview of Materials Qualification Needs for Metal Additive Manufacturing
Seifi, M., Salem, A., Beuth, J., Harrysson, O., & Lewandowski, J. J. (2016) · JOM · doi:10.1007/s11837-015-1810-0 · Cited by 630
Spierings, A. B., Herres, N., & Levy, G. (2011) · Rapid Prototyping Journal · doi:10.1108/13552541111124770 · Cited by 614
Residual Stress within Metallic Model Made by Selective Laser Melting Process
Shiomi, M., Osakada, K., Nakamura, K., Yamashita, T., & Abe, F. (2004) · CIRP Annals · doi:10.1016/s0007-8506(07)60677-5 · Cited by 591
Grading Aggregates - I. - Mathematical Relations for Beds of Broken Solids of Maximum Density
Furnas, C. C. (1931) · Industrial & Engineering Chemistry · doi:10.1021/ie50261a017 · Cited by 571
Castellanos, A. (2005) · Advances in Physics · doi:10.1080/17461390500402657 · Cited by 555
Vrancken, B., Thijs, L., Kruth, J.-P., & Van Humbeeck, J. (2014) · Acta Materialia · doi:10.1016/j.actamat.2014.01.018 · Cited by 553
The use of bulk density measurements as flowability indicators
Abdullah, E. C., & Geldart, D. (1999) · Powder Technology · doi:10.1016/s0032-5910(98)00208-3 · Cited by 544
Kruth, J.-P., Deckers, J., Yasa, E., & Wauthlé, R. (2012) · Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture · doi:10.1177/0954405412437085 · Cited by 532
Absorptance of powder materials suitable for laser sintering
Tolochko, N. K., Khlopkov, Y. V., Mozzharov, S. E., Ignatiev, M. B., Laoui, T., & Titov, V. I. (2000) · Rapid Prototyping Journal · doi:10.1108/13552540010337029 · Cited by 518
Characterization of Metal Powders Used for Additive Manufacturing
Slotwinski, J. A., Garboczi, E. J., Stutzman, P. E., Ferraris, C. F., Watson, S. S., & Peltz, M. A. (2014) · Journal of Research of the National Institute of Standards and Technology · doi:10.6028/jres.119.018 · Cited by 506
Particle packing characteristics
Dodds, J. (1990) · Powder Technology · doi:10.1016/0032-5910(90)80071-6 · Cited by 499
Liu, Y., Yang, Y., Mai, S., Wang, D., & Song, C. (2015) · Materials & Design · doi:10.1016/j.matdes.2015.08.086 · Cited by 498
Tolosa, I., Garciandía, F., Zubiri, F., Zapirain, F., & Esnaola, A. (2010) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-010-2631-5 · Cited by 487
Tang, H. P., Qian, M., Liu, N., Zhang, X. Z., Yang, G. Y., & Wang, J. (2015) · JOM · doi:10.1007/s11837-015-1300-4 · Cited by 483
Li, R., Shi, Y., Wang, Z., Wang, L., Liu, J., & Jiang, W. (2010) · Applied Surface Science · doi:10.1016/j.apsusc.2010.02.030 · Cited by 473
Particle packing characteristics
German, R. M. (1989) · Medical Entomology and Zoology · Cited by 471
Mesoscopic simulation of selective beam melting processes
Körner, C., Attar, E., & Heinl, P. (2011) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2010.12.016 · Cited by 450
Top surface and side roughness of Inconel 625 parts processed using selective laser melting
Mumtaz, K., & Hopkinson, N. (2009) · Rapid Prototyping Journal · doi:10.1108/13552540910943397 · Cited by 429
Song, B., Zhao, X., Li, S., Han, C., Wei, Q., Wen, S., Liu, J., & Shi, Y. (2015) · Frontiers of Mechanical Engineering · doi:10.1007/s11465-015-0341-2 · Cited by 427
Andreasen, A. H. M. (1930) · Kolloid-Zeitschrift · doi:10.1007/bf01422986 · Cited by 423
Powder flowability characterisation methodology for powder-bed-based metal additive manufacturing
Spierings, A. B., Voegtlin, M., Bauer, T., & Wegener, K. (2015) · Progress in Additive Manufacturing · doi:10.1007/s40964-015-0001-4 · Cited by 415
Fundamentals of Selective Laser Melting of alloyed steel powders
Rombouts, M., Kruth, J. P., Froyen, L., & Mercelis, P. (2006) · CIRP Annals · doi:10.1016/s0007-8506(07)60395-3 · Cited by 400
Kamath, C., El-dasher, B., Gallegos, G. F., King, W. E., & Sisto, A. (2014) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-014-5954-9 · Cited by 395
A new approach to the design and optimisation of support structures in additive manufacturing
Strano, G., Hao, L., Everson, R. M., & Evans, K. E. (2013) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-012-4403-x · Cited by 389
Yasa, E., Deckers, J., & Kruth, J. (2011) · Rapid Prototyping Journal · doi:10.1108/13552541111156450 · Cited by 371
Calculation of laser absorption by metal powders in additive manufacturing
Boley, C. D., Khairallah, S. A., & Rubenchik, A. M. (2015) · Applied Optics · doi:10.1364/ao.54.002477 · Cited by 371
Zhang, B., Dembinski, L., & Coddet, C. (2013) · Materials Science and Engineering: A · doi:10.1016/j.msea.2013.06.055 · Cited by 370
Sintering of commercially pure titanium powder with a Nd:YAG laser source
Fischer, P., Romano, V., Weber, H. P., Karapatis, N. P., Boillat, É., & Glardon, R. (2003) · Acta Materialia · doi:10.1016/s1359-6454(02)00567-0 · Cited by 365
Characterization of powder flowability using measurement of angle of repose
Geldart, D., Abdullah, E. C., Hassanpour, A., Nwoke, L. C., & Wouters, I. M. F. (2006) · 中国颗粒学报:英文版 · doi:10.1016/s1672-2515(07)60247-4 · Cited by 363
Simonelli, M., Tuck, C., Aboulkhair, N. T., Maskery, I., Ashcroft, I., Wildman, R. D., & Hague, R. (2015) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-015-2882-8 · Cited by 342
Schoinochoritis, B., Chantzis, D., & Salonitis, K. (2015) · Proceedings of the Institution of Mechanical Engineers Part B Journal of Engineering Manufacture · doi:10.1177/0954405414567522 · Cited by 341
Characterization and Control of Powder Properties for Additive Manufacturing
Strondl, A., Lyckfeldt, O., Brodin, H., & Ackelid, U. (2015) · JOM · doi:10.1007/s11837-015-1304-0 · Cited by 340
Röttger, A., Geenen, K., Windmann, M., Binner, F., & Theisen, W. (2016) · Materials Science and Engineering A · doi:10.1016/j.msea.2016.10.012 · Cited by 310
Delgado, J., Ciurana, J., & Rodríguez, C. A. (2012) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-011-3643-5 · Cited by 305
Part and material properties in selective laser melting of metals
Kruth, J., Badrossamay, M., Yasa, E., Deckers, J. P., Thijs, L., & Humbeeck, J. V. (2010) · Lirias · Cited by 303
The Influence of Processing Parameters on the Mechanical Properties of SLM Parts
Hanzl, P., Zetek, M., Bakša, T., & Kroupa, T. (2015) · Procedia Engineering · doi:10.1016/j.proeng.2015.01.510 · Cited by 291
Characterization of powder flow: Static and dynamic testing
Krantz, M. J., Zhang, H., & Zhu, J. (2009) · Powder Technology · doi:10.1016/j.powtec.2009.05.001 · Cited by 289
Modeling the interaction of laser radiation with powder bed at selective laser melting
Gusarov, A. V., & Smurov, I. Y. (2010) · Physics Procedia · doi:10.1016/j.phpro.2010.08.065 · Cited by 284
Ardila, L. C., Garciandia, F., González-Díaz, J. B., Álvarez, P., Echeverria, A., Petite, M. M., Deffley, R., & Ochoa, J. (2014) · Physics Procedia · doi:10.1016/j.phpro.2014.08.152 · Cited by 268
Manufacturing by combining Selective Laser Melting and Selective Laser Erosion/laser re-melting
Yasa, E., Kruth, J.-P., & Deckers, J. (2011) · CIRP Annals · doi:10.1016/j.cirp.2011.03.063 · Cited by 265
Karlsson, J., Snis, A., Engqvist, H., & Lausmaa, J. (2013) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2013.06.010 · Cited by 254
Wang, D., Liu, Y., Yang, Y., & Xiao, D. (2016) · Rapid Prototyping Journal · doi:10.1108/rpj-06-2015-0078 · Cited by 254
Standard test method for thermal diffusivity of solids by the flash method
Astm, E. (1992) · Medical Entomology and Zoology · Cited by 253
Prediction of porosity in metal-based additive manufacturing using spatial Gaussian process models
Tapia, G., Elwany, A. H., & Sang, H. (2016) · Additive Manufacturing · doi:10.1016/j.addma.2016.05.009 · Cited by 250
Dawes, J., Bowerman, R., & Trepleton, R. (2015) · Johnson Matthey Technology Review · doi:10.1595/205651315x688686 · Cited by 248
Parametric optimization of selective laser melting for forming Ti6Al4V samples by Taguchi method
Sun, J., Yang, Y., & Wang, D. (2013) · Optics & Laser Technology · doi:10.1016/j.optlastec.2012.12.002 · Cited by 232
Microstructure and tensile properties of iron parts fabricated by selective laser melting
Song, B., Dong, S., Deng, S., Liao, H., & Coddet, C. (2014) · Optics & Laser Technology · doi:10.1016/j.optlastec.2013.09.017 · Cited by 219
Microstructure and mechanical properties of selective laser melted magnesium
Ng, C. C., Savalani, M. M., Lau, M. L., & Man, H. C. (2011) · Applied Surface Science · doi:10.1016/j.apsusc.2011.03.004 · Cited by 208
Density of Additively-Manufactured, 316L SS Parts Using Laser Powder-Bed Fusion at Powers Up to 400W
Lawrence Livermore National Lab. (LLNL), L., Kamath, C., USDOE, El-dasher, B., Gallegos, G., King, W. E., & Sisto, A. (2013) · doi:10.2172/1116929 · Cited by 207
Viewpoint: metallurgical aspects of powder bed metal additive manufacturing
Hebert, R. J. (2016) · Journal of Materials Science · doi:10.1007/s10853-015-9479-x · Cited by 197
Contact thermal conductivity of a powder bed in selective laser sintering
Gusarov, A. V., Laoui, T., Froyen, L., & Titov, V. I. (2003) · International Journal of Heat and Mass Transfer · doi:10.1016/s0017-9310(02)00370-8 · Cited by 195
Spierings, A. B., & Levy, G. N. (2009) · doi:10.26153/tsw/15113 · Cited by 193
Song, B., Dong, S., Liu, Q., Liao, H., & Coddet, C. (2014) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2013.08.085 · Cited by 189
Prediction of sintered density for bimodal powder mixtures
German, R. M. (1992) · Metallurgical Transactions A · doi:10.1007/bf02647329 · Cited by 183
Oxygen effects on the mechanical properties and lattice strain of Ti and Ti-6Al-4V
Oh, J. M., Lee, B. G., Cho, S. W., Lee, S. W., Choi, G. S., & Lim, J. W. (2011) · Metals and Materials International · doi:10.1007/s12540-011-1006-2 · Cited by 178
Photopyroelectric measurement of thermal conductivity of metallic powders
Rombouts, M., Froyen, L., Gusarov, A. V., Bentefour, E. H., & Glorieux, C. (2005) · Journal of Applied Physics · doi:10.1063/1.1832740 · Cited by 170
Simulation of Laser Beam Melting of Steel Powders using the Three-Dimensional Volume of Fluid Method
Gürtler, F.-J., Karg, M., Leitz, K.-H., & Schmidt, M. (2013) · Physics Procedia · doi:10.1016/j.phpro.2013.03.162 · Cited by 165
Influence of energy density on metallurgy and properties in metal additive manufacturing
Yusuf, S. M., & Gao, N. (2017) · Materials Science and Technology · doi:10.1080/02670836.2017.1289444 · Cited by 163
The influence of heat accumulation on the surface roughness in powder-bed additive manufacturing
Jamshidinia, M., & Kovacevic, R. (2015) · Surface Topography: Metrology and Properties · doi:10.1088/2051-672x/3/1/014003 · Cited by 159
Liu, B., Wildman, R. D., Tuck, C. J., Ashcroft, I., & Hague, R. (2011) · doi:10.26153/tsw/15290 · Cited by 159
Dai, D., & Gu, D. (2015) · Applied Surface Science · doi:10.1016/j.apsusc.2015.07.044 · Cited by 147
Additive Manufacturing of Metals: A Review
Herderick, E. D. (2011) · Cited by 140
Selective laser melting of Al-12Si alloy: Enhanced densification via powder drying
Li, X., O'Donnell, K. M., & Sercombe, T. B. (2016) · Additive manufacturing · doi:10.1016/j.addma.2016.01.003 · Cited by 135
Metrology Needs for Metal Additive Manufacturing Powders
Slotwinski, J. A., & Garboczi, E. J. (2015) · JOM · doi:10.1007/s11837-014-1290-7 · Cited by 132
Optimization of Powder Layer Density in Selective Laser Sintering
Karapatis, N. P., Egger, G., Gygax, P. E., & Glardon, R. (1999) · Infoscience (Ecole Polytechnique Fédérale de Lausanne) · doi:10.26153/tsw/746 · Cited by 112
Zhou, J., Zhang, Y., & Chen, J. K. (2009) · Journal of Manufacturing Science and Engineering · doi:10.1115/1.3123324 · Cited by 110
Irrinki, H., Dexter, M., Barmore, B., Enneti, R. K., Pasebani, S., Badwe, S., Stitzel, J., Malhotra, R., & Atre, S. V. (2016) · JOM · doi:10.1007/s11837-015-1770-4 · Cited by 102
Optimising metal powders for additive manufacturing
Clayton, J. (2014) · Metal Powder Report · doi:10.1016/s0026-0657(14)70223-1 · Cited by 93
Cooke, A., & Slotwinski, J. A. (2012) · doi:10.6028/nist.ir.7873 · Cited by 90
Measurement of powder bed density in powder bed fusion additive manufacturing processes
Jacob, G., Donmez, A., Slotwinski, J. A., & Moylan, S. P. (2016) · Measurement Science and Technology · doi:10.1088/0957-0233/27/11/115601 · Cited by 87
A New Approach for a Flexible Powder Production for Additive Manufacturing
Dietrich, S., Wunderer, M., Huissel, A., & Zaeh, M. F. (2016) · Procedia Manufacturing · doi:10.1016/j.promfg.2016.11.012 · Cited by 80
Fundamentals of Energy Conversion and Dissipation in Powder Layers during Laser Micro Sintering
Streek, A., Regenfuß, P., & Exner, H. (2013) · Physics Procedia · doi:10.1016/j.phpro.2013.03.159 · Cited by 59
Controlling Phase Composition in Selective Laser Melted Stainless Steels
Starr, T. L., Rafi, K., Stucker, B. E., & Scherzer, C. M. (2012) · doi:10.26153/tsw/15363 · Cited by 58
Affinity scale between a carrier and a drug in DPI studied by atomic force microscopy
Bérard, V., Lesniewska, É., Andrès, C., Pertuy, D., Laroche, C., & Pourcelot, Y. (2002) · International Journal of Pharmaceutics · doi:10.1016/s0378-5173(02)00400-3 · Cited by 57
An investigation into the recycling of Ti-6Al-4V powder used within SLM to improve sustainability
O’Leary, R., Setchi, R., & Prickett, P. W. (2015) · ORCA Online Research @Cardiff (Cardiff University) · Cited by 42
Benson, J. M., & Snyders, E. (2015) · The South African Journal of Industrial Engineering · doi:10.7166/26-2-951 · Cited by 28
Cited by
Binder jet 3D printing—Process parameters, materials, properties, modeling, and challenges
Mostafaei, A., Elliott, A. M., Barnes, J. E., Li, F., Tan, W., Cramer, C. L., Nandwana, P., & Chmielus, M. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100707 · Cited by 1,093
Additive manufacturing of advanced ceramic materials
Lakhdar, Y., Tuck, C., Binner, J., Terry, A., & Goodridge, R. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100736 · Cited by 857
Nguyen, H. D., Pramanik, A., Basak, A. K., Dong, Y., Prakash, C., Debnath, S., Shankar, S., Jawahir, I. S., Dixit, S., & Buddhi, D. (2022) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2022.04.055 · Cited by 634
du Plessis, A., Yadroitsev, I., Yadroitsava, I., & Le Roux, S. G. (2018) · 3D Printing and Additive Manufacturing · doi:10.1089/3dp.2018.0060 · Cited by 550
Powder Bed Fusion of nickel-based superalloys: A review
Sanchez, S., Smith, P., Xu, Z., Gaspard, G., Hyde, C. J., Wits, W. W., Ashcroft, I. A., Chen, H., & Clare, A. T. (2021) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2021.103729 · Cited by 541
Metadata
- Authors
- Tan, J. H., Wong, W. L. E., & Dalgarno, K. W.
- Venue
- Additive Manufacturing
- Publisher
- Elsevier BV
- Published
- 2017-12
- Volume
- 18
- Pages
- 228-255
- ISSN
- 2214-7810 (ISSN-L)
- 2214-8604
- OpenAlex
- W2762497481
- Cited by
- 407
- References
- 107
- FWCI
- 22.57
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.