The DOI matches its Crossref record; 35 of the 35 references it cites were found in a registry or an index.
The mechanical properties and cytotoxicity of cell-laden double-network hydrogels based on photocrosslinkable gelatin and gellan gum biomacromolecules
Open accessAbstract
A major goal in the application of hydrogels for tissue engineering scaffolds, especially for load-bearing tissues such as cartilage, is to develop hydrogels with high mechanical strength. In this study, a double-network (DN) strategy was used to engineer strong hydrogels that can encapsulate cells. We improved upon previously studied double-network (DN) hydrogels by using a processing condition compatible with cell survival. The DN hydrogels were created by a two-step photocrosslinking using gellan gum methacrylate (GGMA) for the rigid and brittle first network, and gelatin methacrylamide (GelMA) for the soft and ductile second network. We controlled the degree of methacrylation of each polymer so that they obtain relevant mechanical properties as each network. The DN was formed by photocrosslinking the GGMA, diffusing GelMA into the first network, and photocrosslinking the GelMA to form the second network. The formation of the DN was examined by diffusion tests of the large GelMA molecules into the GGMA network, the resulting enhancement in the mechanical properties, and the difference in mechanical properties between GGMA/GelMA single networks (SN) and DNs. The resulting DN hydrogels exhibited the compressive failure stress of up to 6.9 MPa, which approaches the strength of cartilage. It was found that there is an optimal range of the crosslink density of the second network for high strength of DN hydrogels. DN hydrogels with a higher mass ratio of GelMA to GGMA exhibited higher strength, which shows promise in developing even stronger DN hydrogels in the future. Three dimensional (3D) encapsulation of NIH-3T3 fibroblasts and the following viability test showed the cell-compatibility of the DN formation process. Given the high strength and the ability to encapsulate cells, the DN hydrogels made from photocrosslinkable macromolecules could be useful for the regeneration of load-bearing tissues.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Principles of Polymer Chemistry.
Huggins, M. L. (1954) · Journal of the American Chemical Society · doi:10.1021/ja01639a090 · Cited by 16,550
Principles of polymer chemistry
(1995) · Choice Reviews Online · doi:10.5860/choice.33-2140 · Cited by 15,218
Biomechanics. Mechanical Properties of Living Tissues
Fung, Y. C., & Skalak, R. (1982) · Journal of Applied Mechanics · doi:10.1115/1.3162171 · Cited by 6,025
Hydrogels for Tissue Engineering
Lee, K. Y., & Mooney, D. J. (2001) · Chemical Reviews · doi:10.1021/cr000108x · Cited by 5,277
Hydrogels for tissue engineering: scaffold design variables and applications
Drury, J. L., & Mooney, D. J. (2003) · Biomaterials · doi:10.1016/s0142-9612(03)00340-5 · Cited by 5,136
Double‐Network Hydrogels with Extremely High Mechanical Strength
Gong, J. P., Katsuyama, Y., Kurokawa, T., & Osada, Y. (2003) · Advanced Materials · doi:10.1002/adma.200304907 · Cited by 4,542
Hydrogels in Biology and Medicine: From Molecular Principles to Bionanotechnology
Peppas, N. A., Hilt, J. Z., Khademhosseini, A., & Langer, R. (2006) · Advanced Materials · doi:10.1002/adma.200501612 · Cited by 4,109
Self-citationCell-laden microengineered gelatin methacrylate hydrogels
Nichol, J. W., Koshy, S. T., Bae, H., Hwang, C. M., Yamanlar, S., & Khademhosseini, A. (2010) · Biomaterials · doi:10.1016/j.biomaterials.2010.03.064 · Cited by 2,377 · cited 2×
“Both polymers were methacrylated by reacting them with methacrylic anhydride [23, 29] (Fig.”
Self-citationWhy are double network hydrogels so tough?
Gong, J. P. (2010) · Soft Matter · doi:10.1039/b924290b · Cited by 2,328
Microscale technologies for tissue engineering and biology
Khademhosseini, A., Langer, R., Borenstein, J., & Vacanti, J. P. (2006) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.0507681102 · Cited by 1,558
Self-citation
Cited by
Synthesis, properties, and biomedical applications of gelatin methacryloyl (GelMA) hydrogels
Yue, K., Trujillo-de Santiago, G., Alvarez, M. M., Tamayol, A., Annabi, N., & Khademhosseini, A. (2015) · Biomaterials · doi:10.1016/j.biomaterials.2015.08.045 · Cited by 3,146
“Biopolymers Gellan gum methacrylate Reinforce GelMA hydrogels NIH-3T3 fibroblasts Cartilage [90] HA and chondroitin sulfate methacrylate Enhance chondrogenesis and mechanical properties Human chondrocytes Cartilage [85]”
BackgroundMethodInfluentialSelf-citation25th Anniversary Article: Engineering Hydrogels for Biofabrication
Malda, J., Visser, J., Melchels, F. P., Jüngst, T., Hennink, W. E., Dhert, W. J. A., Groll, J., & Hutmacher, D. W. (2013) · Advanced Materials · doi:10.1002/adma.201302042 · Cited by 1,901
Bioinks for 3D bioprinting: an overview
Gungor-Ozkerim, P. S., Inci, I., Zhang, Y. S., Khademhosseini, A., & Dokmeci, M. R. (2018) · Biomaterials Science · doi:10.1039/c7bm00765e · Cited by 1,428
Self-citationMulti-scale multi-mechanism design of tough hydrogels: building dissipation into stretchy networks
Zhao, X. (2014) · Soft Matter · doi:10.1039/c3sm52272e · Cited by 1,252
Biocompatibility of hydrogel-based scaffolds for tissue engineering applications
Naahidi, S., Jafari, M., Logan, M., Wang, Y., Yuan, Y., Bae, H., Dixon, B., & Chen, P. (2017) · Biotechnology Advances · doi:10.1016/j.biotechadv.2017.05.006 · Cited by 907
3D printing of hydrogels: Rational design strategies and emerging biomedical applications
Li, J., Wu, C., Chu, P. K., & Gelinsky, M. (2020) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2020.100543 · Cited by 862
Photocrosslinkable Gelatin Hydrogel for Epidermal Tissue Engineering
Zhao, X., Lang, Q., Yildirimer, L., Lin, Z. Y., Cui, W., Annabi, N., Ng, K. W., Dokmeci, M. R., Ghaemmaghami, A. M., & Khademhosseini, A. (2016) · Advanced Healthcare Materials · doi:10.1002/adhm.201500005 · Cited by 832
Self-citationSchuurman, W., Levett, P. A., Pot, M. W., van Weeren, P. R., Dhert, W. J. A., Hutmacher, D. W., Melchels, F. P. W., Klein, T. J., & Malda, J. (2013) · Macromolecular Bioscience · doi:10.1002/mabi.201200471 · Cited by 790
Cell-laden hydrogels for osteochondral and cartilage tissue engineering
Yang, J., Zhang, Y. S., Yue, K., & Khademhosseini, A. (2017) · Acta Biomaterialia · doi:10.1016/j.actbio.2017.01.036 · Cited by 652
Self-citationBiomaterials for articular cartilage tissue engineering: Learning from biology
Armiento, A. R., Stoddart, M. J., Alini, M., & Eglin, D. (2018) · Acta Biomaterialia · doi:10.1016/j.actbio.2017.11.021 · Cited by 579
Extracellular matrix scaffolds for cartilage and bone regeneration
Benders, K. E. M., Weeren, P. R. V., Badylak, S. F., Saris, D. B. F., Dhert, W. J. A., & Malda, J. (2013) · Trends in Biotechnology · doi:10.1016/j.tibtech.2012.12.004 · Cited by 538
Bioinspired fabrication of high strength hydrogels from non-covalent interactions
Wang, W., Zhang, Y., & Liu, W. (2017) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2017.04.001 · Cited by 517
An Introduction to 3D Bioprinting: Possibilities, Challenges and Future Aspects
Kačarević, Ž. P., Rider, P. M., Alkildani, S., Retnasingh, S., Smeets, R., Jung, O., Ivanišević, Z., & Barbeck, M. (2018) · Materials · doi:10.3390/ma11112199 · Cited by 479
Precise Tuning of Facile One-Pot Gelatin Methacryloyl (GelMA) Synthesis
Shirahama, H., Lee, B. H., Tan, L. P., & Cho, N.-J. (2016) · Scientific Reports · doi:10.1038/srep31036 · Cited by 473
Sun, M., Sun, X., Wang, Z., Guo, S., Yu, G., & Yang, H. (2018) · Polymers · doi:10.3390/polym10111290 · Cited by 449
Zhao, X., Liu, S., Yildirimer, L., Zhao, H., Ding, R., Wang, H., Cui, W., & Weitz, D. (2016) · Advanced Functional Materials · doi:10.1002/adfm.201504943 · Cited by 426
Application of gellan gum in pharmacy and medicine
Osmałek, T., Froelich, A., & Tasarek, S. (2014) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2014.03.038 · Cited by 421
Degradable natural polymer hydrogels for articular cartilage tissue engineering
Zhao, W., Jin, X., Cong, Y., Liu, Y., & Fu, J. (2013) · Journal of Chemical Technology & Biotechnology · doi:10.1002/jctb.3970 · Cited by 421
Eke, G., Mangir, N., Hasirci, N., MacNeil, S., & Hasirci, V. (2017) · Biomaterials · doi:10.1016/j.biomaterials.2017.03.021 · Cited by 417
Bao, Z., Xian, C., Yuan, Q., Liu, G., & Wu, J. (2019) · Advanced Healthcare Materials · doi:10.1002/adhm.201900670 · Cited by 383
Biofabrication of tissue constructs by 3D bioprinting of cell-laden microcarriers
Levato, R., Visser, J., Planell, J. A., Engel, E., Malda, J., & Mateos-Timoneda, M. A. (2014) · Biofabrication · doi:10.1088/1758-5082/6/3/035020 · Cited by 380
Recent trends on gellan gum blends with natural and synthetic polymers: A review
Zia, K. M., Tabasum, S., Khan, M. F., Akram, N., Akhter, N., Noreen, A., & Zuber, M. (2018) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2017.11.099 · Cited by 370
Liu, B., Wang, Y., Miao, Y., Zhang, X., Fan, Z., Singh, G., Zhang, X., Xu, K., Li, B., Hu, Z., et al. (2018) · Biomaterials · doi:10.1016/j.biomaterials.2018.04.023 · Cited by 338
An overview of the suitability of hydrogel-forming polymers for extrusion-based 3D-printing
Kirchmajer, D. M., Gorkin III, R., & in het Panhuis, M. (2015) · Journal of Materials Chemistry B · doi:10.1039/c5tb00393h · Cited by 337
Mushtaq, F., Raza, Z. A., Batool, S. R., Zahid, M., Onder, O. C., Rafique, A., & Nazeer, M. A. (2022) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2022.07.168 · Cited by 327
Enhancing Biopolymer Hydrogel Functionality through Interpenetrating Networks
Dhand, A. P., Galarraga, J. H., & Burdick, J. A. (2021) · Trends in Biotechnology · doi:10.1016/j.tibtech.2020.08.007 · Cited by 314
Evolution of Bioinks and Additive Manufacturing Technologies for 3D Bioprinting
Jose, R. R., Rodriguez, M. J., Dixon, T. A., Omenetto, F., & Kaplan, D. L. (2016) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.6b00088 · Cited by 302
Biomedical applications of gelatin methacryloyl hydrogels
Piao, Y., You, H., Xu, T., Bei, H.-P., Piwko, I. Z., Kwan, Y. Y., & Zhao, X. (2021) · Engineered Regeneration · doi:10.1016/j.engreg.2021.03.002 · Cited by 295
Rodell, C. B., Dusaj, N. N., Highley, C. B., & Burdick, J. A. (2016) · Advanced Materials · doi:10.1002/adma.201602268 · Cited by 291
Cheng, H., Yue, K., Kazemzadeh-Narbat, M., Liu, Y., Khalilpour, A., Li, B., Zhang, Y. S., Annabi, N., & Khademhosseini, A. (2017) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.6b16779 · Cited by 264
Self-citationGelatin hydrogels formed by orthogonal thiol–norbornene photochemistry for cell encapsulation
Mũnoz, Z., Shih, H., & Lin, C.-C. (2014) · Biomater. Sci. · doi:10.1039/c4bm00070f · Cited by 253
Kim, H. H., Kim, J. W., Choi, J., Park, Y. H., & Ki, C. S. (2018) · Polymer · doi:10.1016/j.polymer.2018.08.019 · Cited by 53
Rajkumar, M., Sakthivel, M., Senthilkumar, K., Thangaraj, R., & Kannan, S. (2022) · Current Research in Pharmacology and Drug Discovery · doi:10.1016/j.crphar.2022.100100 · Cited by 29
Oh, J., & Kim, B. (2020) · Korea-Australia Rheology Journal · doi:10.1007/s13367-020-0005-6 · Cited by 28
Metadata
- Authors
- Shin, H., Olsen, B. D., & Khademhosseini, A.
- Venue
- Biomaterials
- Publisher
- Elsevier BV
- Published
- 2012-04
- Volume
- 33
- Issue
- 11
- Pages
- 3143-3152
- ISSN
- 0142-9612 (ISSN-L)
- OpenAlex
- W2077713404
- Cited by
- 400
- References
- 35
- FWCI
- 10.83
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.