The DOI matches its Crossref record; 10 of the 10 references it cites were found in a registry or an index.
Hardened properties of high-performance printing concrete
Open accessAbstract
This paper presents the hardened properties of a high-performance fibre-reinforced fine-aggregate concrete extruded through a 9 mm diameter nozzle to build layer-by-layer structural components in a printing process. The printing process is a digitally controlled additive method capable of manufacturing architectural and structural components without formwork, unlike conventional concrete construction methods. The effects of the layering process on density, compressive strength, flexural strength, tensile bond strength and drying shrinkage are presented together with the implication for mix proportions. A control concrete (mould-cast specimens) had a density of approximately 2250 kg/m3, high strength (107 MPa in compression, 11 MPa in flexure) and 3 MPa in direct tension, together with a relatively low drying shrinkage of 175 μm (cured in water) and 855 μm (cured in a chamber at 20 °C and 60% relative humidity) at 184 days. In contrast well printed concrete had a density of 2350 kg/m3, compressive strength of 75–102 MPa, flexural strength of 6–17 MPa depending on testing direction, and tensile bond strength between layers varying from 2.3 to 0.7 MPa, reducing as the printing time gap between layers increased. The well printed concrete had significantly fewer voids greater than 0.2 mm diameter (1.0%) when compared with the mould-cast control (3.8%), whilst samples of poorly printed material had more voids (4.8%) mainly formed in the interstices between filaments. The additive extrusion process was thus shown to retain the intrinsic high performance of the material.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Neville, A. M. (1968) · Virtual Defense Library (Ministerio de Defensa) · Cited by 5,444
Okamura, H., & Ouchi, M. (2003) · Journal of Advanced Concrete Technology · doi:10.3151/jact.1.5 · Cited by 1,850
Mix design and fresh properties for high-performance printing concrete
Le, T. T., Austin, S. A., Lim, S., Buswell, R. A., Gibb, A. G. F., & Thorpe, T. (2012) · Materials and Structures · doi:10.1617/s11527-012-9828-z · Cited by 1,218
Self-citationFreeform Construction: Mega-scale Rapid Manufacturing for construction
Buswell, R. A., Soar, R. C., Gibb, A. G. F., & Thorpe, A. (2007) · Automation in Construction · doi:10.1016/j.autcon.2006.05.002 · Cited by 536
Self-citationInfluence of key parameters on drying shrinkage of cementitious materials
Bissonnette, B., Pierre, P., & Pigeon, M. (1999) · Cement and Concrete Research · doi:10.1016/s0008-8846(99)00156-8 · Cited by 422
Mega-scale fabrication by Contour Crafting
Khoshnevis, B., Hwang, D., Yao, K. T., & Yeh, Z. (2006) · International Journal of Industrial and Systems Engineering · doi:10.1504/ijise.2006.009791 · Cited by 378
Influence of silica fume on the tensile strength of concrete
Bhanja, S., & Sengupta, B. (2004) · Cement and Concrete Research · doi:10.1016/j.cemconres.2004.05.024 · Cited by 352
Final report of RILEM TC 188-CSC ‘Casting of self compacting concrete’
Committe, R. T. (2006) · Materials and Structures · doi:10.1617/s11527-006-9186-9 · Cited by 48
Fabricating construction components using layer manufacturing technology
Lim, S., Le, T., Webster, J. T., Buswell, R. A., Austin, S. A., Gibb, A., & Thorpe, T. (2009) · Open Research Online (The Open University) · Cited by 45
Self-citationEvans, M., & Campbell, R. I. (2003) · Rapid Prototyping Journal · doi:10.1108/13552540310502248 · Cited by 45
Cited by
3D printing using concrete extrusion: A roadmap for research
Buswell, R. A., Leal de Silva, W. R., Jones, S. Z., & Dirrenberger, J. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.05.006 · Cited by 1,604
Self-citationDirect Ink Writing: A 3D Printing Technology for Diverse Materials
Saadi, M. A. S. R., Maguire, A., Pottackal, N. T., Thakur, M. S. H., Ikram, M. M., Hart, A. J., Ajayan, P. M., & Rahman, M. M. (2022) · Advanced Materials · doi:10.1002/adma.202108855 · Cited by 1,335
Bos, F., Wolfs, R., Ahmed, Z., & Salet, T. (2016) · Virtual and Physical Prototyping · doi:10.1080/17452759.2016.1209867 · Cited by 1,257
Vision of 3D printing with concrete — Technical, economic and environmental potentials
De Schutter, G., Lesage, K., Mechtcherine, V., Nerella, V. N., Habert, G., & Agusti-Juan, I. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.06.001 · Cited by 1,072
A critical review of the use of 3-D printing in the construction industry
Wu, P., Wang, J., & Wang, X. (2016) · Automation in Construction · doi:10.1016/j.autcon.2016.04.005 · Cited by 1,002
Gosselin, C., Duballet, R., Roux, P., Gaudillière, N., Dirrenberger, J., & Morel, P. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.03.097 · Cited by 962
Structural built-up of cement-based materials used for 3D-printing extrusion techniques
Perrot, A., Rangeard, D., & Pierre, A. (2016) · Materials and Structures · doi:10.1617/s11527-015-0571-0 · Cited by 959
Early age mechanical behaviour of 3D printed concrete: Numerical modelling and experimental testing
Wolfs, R. J. M., Bos, F. P., & Salet, T. A. M. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.02.001 · Cited by 846
Kazemian, A., Yuan, X., Cochran, E., & Khoshnevis, B. (2017) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2017.04.015 · Cited by 774
Paolini, A., Kollmannsberger, S., & Rank, E. (2019) · Additive Manufacturing · doi:10.1016/j.addma.2019.100894 · Cited by 673
Fresh and hardened properties of 3D printable cementitious materials for building and construction
Paul, S. C., Tay, Y. W. D., Panda, B., & Tan, M. J. (2018) · Archives of Civil and Mechanical Engineering · doi:10.1016/j.acme.2017.02.008 · Cited by 633
Ma, G., Li, Z., & Wang, L. (2018) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2017.12.051 · Cited by 616
Additive construction: State-of-the-art, challenges and opportunities
Labonnote, N., Rønnquist, A., Manum, B., & Rüther, P. (2016) · Automation in Construction · doi:10.1016/j.autcon.2016.08.026 · Cited by 607
Nerella, V. N., Hempel, S., & Mechtcherine, V. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.01.235 · Cited by 605
Measurement of tensile bond strength of 3D printed geopolymer mortar
Panda, B., Paul, S. C., Mohamed, N. A. N., Tay, Y. W. D., & Tan, M. J. (2018) · Measurement · doi:10.1016/j.measurement.2017.08.051 · Cited by 592
Additive manufacturing of geopolymer for sustainable built environment
Panda, B., Paul, S. C., Hui, L. J., Tay, Y. W. D., & Tan, M. J. (2017) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2017.08.165 · Cited by 516
Design of a 3D printed concrete bridge by testing
Salet, T. A. M., Ahmed, Z. Y., Bos, F. P., & Laagland, H. L. M. (2018) · Virtual and Physical Prototyping · doi:10.1080/17452759.2018.1476064 · Cited by 504
Investigation of the rheology and strength of geopolymer mixtures for extrusion-based 3D printing
Panda, B., Unluer, C., & Tan, M. J. (2018) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2018.10.002 · Cited by 482
Properties of 3D-printed fiber-reinforced Portland cement paste
Hambach, M., & Volkmer, D. (2017) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2017.02.001 · Cited by 470
Craveiro, F., Duarte, J. P., Bartolo, H., & Bartolo, P. J. (2019) · Automation in Construction · doi:10.1016/j.autcon.2019.03.011 · Cited by 455
Large-scale digital concrete construction – CONPrint3D concept for on-site, monolithic 3D-printing
Mechtcherine, V., Nerella, V. N., Will, F., Näther, M., Otto, J., & Krause, M. (2019) · Automation in Construction · doi:10.1016/j.autcon.2019.102933 · Cited by 455
Mix design concepts for 3D printable concrete: A review
Zhang, C., Nerella, V. N., Krishna, A., Wang, S., Zhang, Y., Mechtcherine, V., & Banthia, N. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2021.104155 · Cited by 421
Paul, S. C., van Zijl, G. P. A. G., Tan, M. J., & Gibson, I. (2018) · Rapid Prototyping Journal · doi:10.1108/rpj-09-2016-0154 · Cited by 418
Large-scale 3D printing by a team of mobile robots
Zhang, X., Li, M., Lim, J. H., Weng, Y., Tay, Y. W. D., Pham, H., & Pham, Q.-C. (2018) · Automation in Construction · doi:10.1016/j.autcon.2018.08.004 · Cited by 418
A critical review of 3D printing in construction: benefits, challenges, and risks
El-Sayegh, S., Romdhane, L., & Manjikian, S. (2020) · Archives of Civil and Mechanical Engineering · doi:10.1007/s43452-020-00038-w · Cited by 387
Extrusion-based concrete 3D printing from a material perspective: A state-of-the-art review
Mohan, M. K., Rahul, A. V., De Schutter, G., & Van Tittelboom, K. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2020.103855 · Cited by 384
Ghaffar, S. H., Corker, J., & Fan, M. (2018) · Automation in Construction · doi:10.1016/j.autcon.2018.05.005 · Cited by 358
Effects of interlocking on interlayer adhesion and strength of structures in 3D printing of concrete
Zareiyan, B., & Khoshnevis, B. (2017) · Automation in Construction · doi:10.1016/j.autcon.2017.08.019 · Cited by 353
Mesh reinforcing method for 3D Concrete Printing
Marchment, T., & Sanjayan, J. (2020) · Automation in Construction · doi:10.1016/j.autcon.2019.102992 · Cited by 347
Arunothayan, A. R., Nematollahi, B., Ranade, R., Bong, S. H., & Sanjayan, J. (2020) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2020.119546 · Cited by 347
Environmental and economic assessment on 3D printed buildings with recycled concrete
Han, Y., Yang, Z., Ding, T., & Xiao, J. (2021) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2020.123884 · Cited by 322
Hardened properties of layered 3D printed concrete with recycled sand
Ding, T., Xiao, J., Zou, S., & Wang, Y. (2020) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2020.103724 · Cited by 306
Zhu, B., Pan, J., Nematollahi, B., Zhou, Z., Zhang, Y., & Sanjayan, J. (2019) · Materials & Design · doi:10.1016/j.matdes.2019.108088 · Cited by 305
Panda, B., Noor Mohamed, N. A., Paul, S. C., Bhagath Singh, G., Tan, M. J., & Šavija, B. (2019) · Materials · doi:10.3390/ma12132149 · Cited by 301
Steel fibres reinforced 3D printed concrete: Influence of fibre sizes on mechanical performance
Pham, L., Tran, P., & Sanjayan, J. (2020) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2020.118785 · Cited by 296
Anisotropic behavior in bending of 3D printed concrete reinforced with fibers
Ding, T., Xiao, J., Zou, S., & Zhou, X. (2020) · Composite Structures · doi:10.1016/j.compstruct.2020.112808 · Cited by 296
A systematical review of 3D printable cementitious materials
Lu, B., Weng, Y., Li, M., Qian, Y., Leong, K. F., Tan, M. J., & Qian, S. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.02.144 · Cited by 288
Marchment, T., Sanjayan, J., & Xia, M. (2019) · Materials & Design · doi:10.1016/j.matdes.2019.107684 · Cited by 281
Technology readiness: A global snapshot of 3D concrete printing and the frontiers for development
Ma, G., Buswell, R., Leal da Silva, W. R., Wang, L., Xu, J., & Jones, S. Z. (2022) · Cement and Concrete Research · doi:10.1016/j.cemconres.2022.106774 · Cited by 280
Self-citationCements in the 21 st century: Challenges, perspectives, and opportunities
Biernacki, J. J., Bullard, J. W., Sant, G., Brown, K., Glasser, F. P., Jones, S., Ley, T., Livingston, R., Nicoleau, L., Olek, J., et al. (2017) · Journal of the American Ceramic Society · doi:10.1111/jace.14948 · Cited by 276
Souza, M. T., Ferreira, I. M., Guzi de Moraes, E., Senff, L., & Novaes de Oliveira, A. P. (2020) · Journal of Building Engineering · doi:10.1016/j.jobe.2020.101833 · Cited by 268
An investigation into the porosity of extrusion-based 3D printed concrete
Kruger, J., du Plessis, A., & van Zijl, G. (2021) · Additive Manufacturing · doi:10.1016/j.addma.2020.101740 · Cited by 263
Ye, J., Cui, C., Yu, J., Yu, K., & Dong, F. (2021) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2021.122586 · Cited by 262
3-D printing of concrete: Beyond horizons
Khan, M. S., Sanchez, F., & Zhou, H. (2020) · Cement and Concrete Research · doi:10.1016/j.cemconres.2020.106070 · Cited by 260
A process classification framework for defining and describing Digital Fabrication with Concrete
Buswell, R. A., da Silva, W. R. L., Bos, F. P., Schipper, H. R., Lowke, D., Hack, N., Kloft, H., Mechtcherine, V., Wangler, T., & Roussel, N. (2020) · Cement and Concrete Research · doi:10.1016/j.cemconres.2020.106068 · Cited by 254
Self-citationExtra-terrestrial construction processes – Advancements, opportunities and challenges
Lim, S., Prabhu, V. L., Anand, M., & Taylor, L. A. (2017) · Advances in Space Research · doi:10.1016/j.asr.2017.06.038 · Cited by 134
Self-citation
Metadata
- Authors
- Le, T. T., Austin, S. A., Lim, S., Buswell, R. A., Law, R., Gibb, A. G. F., & Thorpe, T.
- Venue
- Cement and Concrete Research
- Publisher
- Elsevier BV
- Published
- 2012-03
- Volume
- 42
- Issue
- 3
- Pages
- 558-566
- ISSN
- 0008-8846 (ISSN-L)
- OpenAlex
- W2009892931
- Cited by
- 1,020
- References
- 10
- FWCI
- 5.35
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.