The DOI matches its Crossref record; 6 of the 6 references it cites were found in a registry or an index.
Effects of Defects in Laser Additive Manufactured Ti-6Al-4V on Fatigue Properties
Open accessAbstract
Laser Additive Manufacturing (LAM) enables economical production of complex lightweight structures as well as patient individual implants. Due to these possibilities the additive manufacturing technology gains increasing importance in the aircraft and the medical industry. Yet these industries obtain high quality standards and demand predictability of material properties for static and dynamic load cases. However, especially fatigue and crack propagation properties are not sufficiently determined. Therefore this paper presents an analysis and simulation of crack propagation behavior considering Laser Additive Manufacturing specific defects, such as porosity and surface roughness. For the mechanical characterization of laser additive manufactured titanium alloy Ti-6Al-4V, crack propagation rates are experimentally determined and used for an analytical modeling and simulation of fatigue. Using experimental results from HCF tests and simulated data, the fatigue and crack resistance performance is analyzed considering material specific defects and surface roughness. The accumulated results enable the reliable prediction of the defects influence on fatigue life of laser additive manufactured titanium components.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Leuders, S., Thöne, M., Riemer, A., Niendorf, T., Tröster, T., Richard, H. A., & Maier, H. J. (2013) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2012.11.011 · Cited by 1,475
Metal Fatigue: Effects of Small Defects and Nonmetallic Inclusions
MURAKAMI, Y. (2002) · Cited by 1,150
Prediction of non propagating cracks
El Haddad, M. H., Topper, T. H., & Smith, K. N. (1979) · Engineering Fracture Mechanics · doi:10.1016/0013-7944(79)90081-x · Cited by 1,088
Laser Additive Manufacturing and Bionics: Redefining Lightweight Design
Emmelmann, C., Sander, P., Kranz, J., & Wycisk, E. (2011) · Physics Procedia · doi:10.1016/j.phpro.2011.03.046 · Cited by 222
Self-citationHigh Cycle Fatigue (HCF) Performance of Ti-6Al-4V Alloy Processed by Selective Laser Melting
Wycisk, E., Emmelmann, C., Siddique, S., & Walther, F. (2013) · Advanced Materials Research · doi:10.4028/www.scientific.net/amr.816-817.134 · Cited by 215
Self-citationMechanical Properties of Additive Manufactured Ti-6Al-4V Using Wire and Powder Based Processes
Brandl, E., Leyens, C., & Palm, F. (2011) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/26/1/012004 · Cited by 131
Cited by
Additive manufacturing (3D printing): A review of materials, methods, applications and challenges
Ngo, T. D., Kashani, A., Imbalzano, G., Nguyen, K. T. Q., & Hui, D. (2018) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2018.02.012 · Cited by 8,431
Additive manufacturing of metals
Herzog, D., Seyda, V., Wycisk, E., & Emmelmann, C. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.07.019 · Cited by 4,759
Self-citationThe metallurgy and processing science of metal additive manufacturing
Sames, W. J., List, F. A., Pannala, S., Dehoff, R. R., & Babu, S. S. (2016) · International Materials Reviews · doi:10.1080/09506608.2015.1116649 · Cited by 2,529
Additive manufacturing of Ti6Al4V alloy: A review
Liu, S., & Shin, Y. C. (2019) · Materials & Design · doi:10.1016/j.matdes.2018.107552 · Cited by 2,472
Sanaei, N., & Fatemi, A. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100724 · Cited by 1,029
Additive manufacturing of fatigue resistant materials: Challenges and opportunities
Yadollahi, A., & Shamsaei, N. (2017) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2017.01.001 · Cited by 1,023
Gong, H., Rafi, K., Gu, H., Janaki Ram, G. D., Starr, T., & Stucker, B. (2015) · Materials & Design · doi:10.1016/j.matdes.2015.07.147 · Cited by 940
Defect formation mechanisms in selective laser melting: a review
Zhang, B., Li, Y., & Bai, Q. (2017) · Chinese Journal of Mechanical Engineering · doi:10.1007/s10033-017-0121-5 · Cited by 924
Beretta, S., & Romano, S. (2017) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2016.06.020 · Cited by 635
Nguyen, H. D., Pramanik, A., Basak, A. K., Dong, Y., Prakash, C., Debnath, S., Shankar, S., Jawahir, I. S., Dixit, S., & Buddhi, D. (2022) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2022.04.055 · Cited by 634
Li, P., Warner, D. H., Fatemi, A., & Phan, N. (2016) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2015.12.003 · Cited by 546
Heat treatment for metal additive manufacturing
Laleh, M., Sadeghi, E., Revilla, R. I., Chao, Q., Haghdadi, N., Hughes, A. E., Xu, W., De Graeve, I., Qian, M., Gibson, I., et al. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2022.101051 · Cited by 538
Fatigue life of additively manufactured Ti–6Al–4V in the very high cycle fatigue regime
Günther, J., Krewerth, D., Lippmann, T., Leuders, S., Tröster, T., Weidner, A., Biermann, H., & Niendorf, T. (2017) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2016.05.018 · Cited by 475
Seifi, M., Gorelik, M., Waller, J., Hrabe, N., Shamsaei, N., Daniewicz, S., & Lewandowski, J. J. (2017) · JOM · doi:10.1007/s11837-017-2265-2 · Cited by 422
Fatigue performance of additive manufactured TiAl6V4 using electron and laser beam melting
Greitemeier, D., Palm, F., Syassen, F., & Melz, T. (2017) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2016.05.001 · Cited by 385
Surface roughness effects on the fatigue strength of additively manufactured Ti-6Al-4V
Pegues, J., Roach, M., Scott Williamson, R., & Shamsaei, N. (2018) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2018.07.013 · Cited by 378
Fracture and fatigue in additively manufactured metals
Becker, T. H., Kumar, P., & Ramamurty, U. (2021) · Acta Materialia · doi:10.1016/j.actamat.2021.117240 · Cited by 377
Methods and materials for additive manufacturing: A critical review on advancements and challenges
Bhuvanesh Kumar, M., & Sathiya, P. (2021) · Thin-Walled Structures · doi:10.1016/j.tws.2020.107228 · Cited by 372
Bagehorn, S., Wehr, J., & Maier, H. J. (2017) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2017.05.008 · Cited by 371
Defect structure process maps for laser powder bed fusion additive manufacturing
Gordon, J. V., Narra, S. P., Cunningham, R. W., Liu, H., Chen, H., Suter, R. M., Beuth, J. L., & Rollett, A. D. (2020) · Additive Manufacturing · doi:10.1016/j.addma.2020.101552 · Cited by 329
Surface modification of biomaterials and biomedical devices using additive manufacturing
Bose, S., Robertson, S. F., & Bandyopadhyay, A. (2018) · Acta Biomaterialia · doi:10.1016/j.actbio.2017.11.003 · Cited by 305
Zhan, Z., & Li, H. (2021) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2020.105941 · Cited by 305
Benedetti, M., Fontanari, V., Bandini, M., Zanini, F., & Carmignato, S. (2018) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2017.10.021 · Cited by 297
Fatemi, A., Molaei, R., Sharifimehr, S., Phan, N., & Shamsaei, N. (2017) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2017.03.044 · Cited by 282
Additive manufacturing and postprocessing of Ti-6Al-4V for superior mechanical properties
Qian, M., Xu, W., Brandt, M., & Tang, H. P. (2016) · MRS Bulletin · doi:10.1557/mrs.2016.215 · Cited by 275
Molaei, R., Fatemi, A., Sanaei, N., Pegues, J., Shamsaei, N., Shao, S., Li, P., Warner, D. H., & Phan, N. (2020) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2019.105363 · Cited by 264
Zerbst, U., Bruno, G., Buffière, J.-Y., Wegener, T., Niendorf, T., Wu, T., Zhang, X., Kashaev, N., Meneghetti, G., Hrabe, N., et al. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2021.100786 · Cited by 263
Smith, J., Xiong, W., Yan, W., Lin, S., Cheng, P., Kafka, O. L., Wagner, G. J., Cao, J., & Liu, W. K. (2016) · Computational Mechanics · doi:10.1007/s00466-015-1240-4 · Cited by 255
Zhan, Z., & Li, H. (2021) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2020.106089 · Cited by 176
du Plessis, A., & Beretta, S. (2020) · Additive Manufacturing · doi:10.1016/j.addma.2020.101424 · Cited by 169
A Review on the Processing of Aero-Turbine Blade Using 3D Print Techniques
Sinha, A., Swain, B., Behera, A., Mallick, P., Samal, S. K., Vishwanatha, H. M., & Behera, A. (2022) · Journal of Manufacturing and Materials Processing · doi:10.3390/jmmp6010016 · Cited by 98
Metadata
- Authors
- Wycisk, E., Solbach, A., Siddique, S., Herzog, D., Walther, F., & Emmelmann, C.
- Venue
- Physics Procedia
- Publisher
- Elsevier BV
- Published
- 2014
- Volume
- 56
- Pages
- 371-378
- ISSN
- 1875-3892 (ISSN-L)
- OpenAlex
- W2060092079
- Cited by
- 509
- References
- 6
- FWCI
- 20.26
- Type
- journal article
- Language
- en
- Open access
- diamond
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.