Multifunctional Wearable Device Based on Flexible and Conductive Carbon Sponge/Polydimethylsiloxane Composite
The DOI matches its Crossref record; 35 of the 35 references it cites were found in a registry or an index.
Abstract
Wearable devices that can be used to monitor personal health, track human motions, and provide thermotherapy, etc., are highly desired in personalized healthcare. In this work, a multifunctional wearable "wrist band" which works as both heater for thermotherapy and sensor for personal health and motion monitoring is fabricated from a flexible and conductive carbon sponge/polydimethylsiloxane (CS/PDMS) composite. The key functional material of the wrist band, namely, the conductive CS, is synthesized from waste paper by a freeze-drying and high-temperature pyrolysis process. When the wrist band works as a heater under 15 V, a stable temperature difference of 20 °C is achieved between the wrist band and the ambient. When the wrist band serves as a wearable strain sensor, the wrist band exhibits fast and repeatable response and excellent durability within the strain range of 0-20% and the working frequency of 0.01-10 Hz. Finally, the typical applications of the multifunctional wearable wrist band, as a heater for thermotherapy and a sensor for blood pulse, breathe, and walk monitoring, are demonstrated. Due to its low cost, high flexibility, moderate conductivity, and excellent strain sensibility, the as-prepared wearable device based on the CS/PDMS composite is promising to be applied for the provision of personal healthcare.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“On the skin, respiratory waves and pulses can also contribute to slight stretches, which can be captured by sensitive strainers for health monitoring during rehabilitation.[94,202,203]”
From Flexible Electronics and Devices as Human–Machine Interfaces for Medical Robotics (2022) · cites this paper as [203]
In the citing paper
“Despite these issues, prosthetic actuation has repeatedly been shown to enhance rehabilitation recovery through assisted motion actuation[458] and heat therapy[203] after paralysis, muscle injury, or loss of limb.[459]”
From Flexible Electronics and Devices as Human–Machine Interfaces for Medical Robotics (2022) · cites this paper as [203]
Citations
Cites
Highly sensitive flexible pressure sensors with microstructured rubber dielectric layers
Mannsfeld, S. C. B., Tee, B. C.-K., Stoltenberg, R. M., Chen, C. V. H.-H., Barman, S., Muir, B. V. O., Sokolov, A. N., Reese, C., & Bao, Z. (2010) · Nature Materials · doi:10.1038/nmat2834 · Cited by 3,291
A review of wearable sensors and systems with application in rehabilitation
Patel, S., Park, H., Bonato, P., Chan, L., & Rodgers, M. (2012) · Journal of NeuroEngineering and Rehabilitation · doi:10.1186/1743-0003-9-21 · Cited by 2,396
Highly Stretchable and Sensitive Strain Sensor Based on Silver Nanowire–Elastomer Nanocomposite
Amjadi, M., Pichitpajongkit, A., Lee, S., Ryu, S., & Park, I. (2014) · ACS Nano · doi:10.1021/nn501204t · Cited by 2,350
A wearable and highly sensitive pressure sensor with ultrathin gold nanowires
Gong, S., Schwalb, W., Wang, Y., Chen, Y., Tang, Y., Si, J., Shirinzadeh, B., & Cheng, W. (2014) · Nature Communications · doi:10.1038/ncomms4132 · Cited by 2,064
Multifunctional wearable devices for diagnosis and therapy of movement disorders
Son, D., Lee, J., Qiao, S., Ghaffari, R., Kim, J., Lee, J. E., Song, C., Kim, S. J., Lee, D. J., Jun, S. W., et al. (2014) · Nature Nanotechnology · doi:10.1038/nnano.2014.38 · Cited by 1,462
Monitoring of Vital Signs with Flexible and Wearable Medical Devices
Khan, Y., Ostfeld, A. E., Lochner, C. M., Pierre, A., & Arias, A. C. (2016) · Advanced Materials · doi:10.1002/adma.201504366 · Cited by 1,408
Advances of flexible pressure sensors toward artificial intelligence and health care applications
Zang, Y., Zhang, F., Di, C.-A., & Zhu, D. (2015) · Materials Horizons · doi:10.1039/c4mh00147h · Cited by 1,272
Yao, H., Ge, J., Wang, C., Wang, X., Hu, W., Zheng, Z., Ni, Y., & Yu, S. (2013) · Advanced Materials · doi:10.1002/adma.201303041 · Cited by 1,137
Wearable and Highly Sensitive Graphene Strain Sensors for Human Motion Monitoring
Wang, Y., Wang, L., Yang, T., Li, X., Zang, X., Zhu, M., Wang, K., Wu, D., & Zhu, H. (2014) · Advanced Functional Materials · doi:10.1002/adfm.201400379 · Cited by 1,085
Wearable multifunctional sensors using printed stretchable conductors made of silver nanowires
Yao, S., & Zhu, Y. (2014) · Nanoscale · doi:10.1039/c3nr05496a · Cited by 1,028
Highly Stretchable and Transparent Metal Nanowire Heater for Wearable Electronics Applications
Hong, S., Lee, H., Lee, J., Kwon, J., Han, S., Suh, Y. D., Cho, H., Shin, J., Yeo, J., & Ko, S. H. (2015) · Advanced Materials · doi:10.1002/adma.201500917 · Cited by 788
Extremely Elastic Wearable Carbon Nanotube Fiber Strain Sensor for Monitoring of Human Motion
Ryu, S., Lee, P., Chou, J. B., Xu, R., Zhao, R., Hart, A. J., & Kim, S.-G. (2015) · ACS Nano · doi:10.1021/acsnano.5b00599 · Cited by 770
Nanomaterial‐Enabled Stretchable Conductors: Strategies, Materials and Devices
Yao, S., & Zhu, Y. (2015) · Advanced Materials · doi:10.1002/adma.201404446 · Cited by 695
Kim, K. K., Hong, S., Cho, H. M., Lee, J., Suh, Y. D., Ham, J., & Ko, S. H. (2015) · Nano Letters · doi:10.1021/acs.nanolett.5b01505 · Cited by 626
Ag Nanowire Reinforced Highly Stretchable Conductive Fibers for Wearable Electronics
Lee, S., Shin, S., Lee, S., Seo, J., Lee, J., Son, S., Cho, H. J., Algadi, H., Al‐Sayari, S., Kim, D. E., et al. (2015) · Advanced Functional Materials · doi:10.1002/adfm.201500628 · Cited by 605
Choi, S., Park, J., Hyun, W., Kim, J., Kim, J., Lee, Y. B., Song, C., Hwang, H. J., Kim, J. H., Hyeon, T., et al. (2015) · ACS Nano · doi:10.1021/acsnano.5b02790 · Cited by 568
A Graphene-Based Resistive Pressure Sensor with Record-High Sensitivity in a Wide Pressure Range
Tian, H., Shu, Y., Wang, X.-F., Mohammad, M. A., Bie, Z., Xie, Q.-Y., Li, C., Mi, W.-T., Yang, Y., & Ren, T.-L. (2015) · Scientific Reports · doi:10.1038/srep08603 · Cited by 524
Cellulose Aerogel from Paper Waste for Crude Oil Spill Cleaning
Nguyen, S. T., Feng, J., Le, N. T., Le, A. T. T., Hoang, N., Tan, V. B. C., & Duong, H. M. (2013) · Industrial & Engineering Chemistry Research · doi:10.1021/ie4032567 · Cited by 380
Xu, X., Zhou, J., Nagaraju, D. H., Jiang, L., Marinov, V. R., Lubineau, G., Alshareef, H. N., & Oh, M. (2015) · Advanced Functional Materials · doi:10.1002/adfm.201500538 · Cited by 324
Li, Y., Samad, Y. A., Polychronopoulou, K., Alhassan, S. M., & Liao, K. (2014) · J. Mater. Chem. A · doi:10.1039/c4ta00839a · Cited by 291
Self-citationSamad, Y. A., Li, Y., Schiffer, A., Alhassan, S. M., & Liao, K. (2015) · Small · doi:10.1002/smll.201403532 · Cited by 231
Self-citationMaterial approaches to stretchable strain sensors
Park, J., You, I., Shin, S., & Jeong, U. (2015) · ChemPhysChem · doi:10.1002/cphc.201402810 · Cited by 216
A carbon nanotube/polymer strain sensor with linear and anti-symmetric piezoresistivity
Yin, G., Hu, N., Karube, Y., Liu, Y., Li, Y., & Fukunaga, H. (2011) · Journal of Composite Materials · doi:10.1177/0021998310393296 · Cited by 206
Self-citationNovel Graphene Foam Composite with Adjustable Sensitivity for Sensor Applications
Samad, Y. A., Li, Y., Alhassan, S. M., & Liao, K. (2015) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.5b01608 · Cited by 200
Self-citationWang, B., Fang, X., Sun, H., He, S., Ren, J., Zhang, Y., & Peng, H. (2015) · Advanced Materials · doi:10.1002/adma.201503441 · Cited by 197
Li, Y.-Q., Samad, Y. A., Polychronopoulou, K., & Liao, K. (2015) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.5b00340 · Cited by 194
Self-citationA hierarchically structured graphene foam and its potential as a large-scale strain-gauge sensor
Kuang, J., Liu, L., Gao, Y., Zhou, D., Chen, Z., Han, B., & Zhang, Z. (2013) · Nanoscale · doi:10.1039/c3nr03379a · Cited by 185
From cotton to wearable pressure sensor
Li, Y., Samad, Y. A., & Liao, K. (2015) · Journal of Materials Chemistry A · doi:10.1039/c4ta05810k · Cited by 184
Self-citationGuo, Y., Li, K., Hou, C., Li, Y., Zhang, Q., & Wang, H. (2016) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.5b11622 · Cited by 162
Self-citationJur, J. S., Sweet, W. J., Oldham, C. J., & Parsons, G. N. (2011) · Advanced Functional Materials · doi:10.1002/adfm.201001756 · Cited by 140
Arnheim's principles of athletic training : a competency-based approach
Prentice, W. E., & Arnheim, D. D. (2002) · Pepperdine Digital Commons (Pepperdine University) · Cited by 119
Highly reproducible printable graphite strain gauges for flexible devices
Bessonov, A. A., Kirikova, M. N., Haque, S., Gartseev, I. B., & Bailey, M. J. A. (2013) · Sensors and Actuators A Physical · doi:10.1016/j.sna.2013.11.034 · Cited by 108
Thermotherapy in dermatologic infections
Doherty, C. B., Doherty, S. D., & Rosen, T. (2010) · Journal of the American Academy of Dermatology · doi:10.1016/j.jaad.2009.09.055 · Cited by 58
Oberoi, S., Sonawane, D., & Kumar, P. (2016) · Composites Science and Technology · doi:10.1016/j.compscitech.2016.03.006 · Cited by 15
Strain rate sensitivity of toughened epoxy
Chaudhary, S., Iqbal, N., Mangla, V., Kumar, D., & Roy, P. K. (2015) · Iranian Polymer Journal · doi:10.1007/s13726-015-0375-7 · Cited by 13
Cited by
PDMS with designer functionalities—Properties, modifications strategies, and applications
Wolf, M. P., Salieb-Beugelaar, G. B., & Hunziker, P. (2018) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2018.06.001 · Cited by 853
Electrically conductive polymer composites for smart flexible strain sensors: a critical review
Liu, H., Li, Q., Zhang, S., Yin, R., Liu, X., He, Y., Dai, K., Shan, C., Guo, J., Liu, C., et al. (2018) · Journal of Materials Chemistry C · doi:10.1039/c8tc04079f · Cited by 709
Flexible Hybrid Electronics for Digital Healthcare
Ma, Y., Zhang, Y., Cai, S., Han, Z., Liu, X., Wang, F., Cao, Y., Wang, Z., Li, H., Chen, Y., et al. (2020) · Advanced Materials · doi:10.1002/adma.201902062 · Cited by 620
Flexible Electronics and Devices as Human–Machine Interfaces for Medical Robotics
Heng, W., Solomon, S., & Gao, W. (2022) · Advanced Materials · doi:10.1002/adma.202107902 · Cited by 609
Liu, Y.-J., Cao, W.-T., Ma, M.-G., & Wan, P. (2017) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.7b07639 · Cited by 544
Metadata
- Authors
- Li, Y.-Q., Zhu, W.-B., Yu, X.-G., Huang, P., Fu, S.-Y., Hu, N., & Liao, K.
- Affiliations
- Chongqing University (CN)
- Khalifa University of Science and Technology (AE)
- Corresponding author
- Fu, Shao-Yun
- Liao, Kin
- Venue
- ACS Applied Materials & Interfaces
- Publisher
- American Chemical Society (ACS)
- Published
- 2016-11-29
- Volume
- 8
- Issue
- 48
- Pages
- 33189-33196
- ISSN
- 1944-8244 (ISSN-L)
- 1944-8252
- OpenAlex
- W2551486358
- Semantic Scholar
- 5f8deb33b7b73b9c6cbe5faa355471927b1fd897
- Cited by
- 207
- References
- 35
- Citations by year
- 2026: 7 · 2025: 10 · 2024: 17 · 2023: 16 · 2022: 34 · 2021: 40 · 2020: 17 · 2019: 25 · 2018: 29 · 2017: 12
- FWCI
- 10.60
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- ACS Applied Materials & Interfaces (publishedVersion)
- PubMed (publishedVersion)
- Funders
- Khalifa University of Science, Technology and Research (210038)
- National Natural Science Foundation of China (11372104, 11572321, 51373187, 51573200)
- Topics
- Physical Sciences › Engineering › Biomedical Engineering › Advanced Sensor and Energy Harvesting Materials
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Nanomaterials and Printing Technologies
- Physical Sciences › Engineering › Biomedical Engineering › Non-Invasive Vital Sign Monitoring
- Keywords
- wearable devices, carbon sponge, polydimethylsiloxane composites, conductive materials, freeze-drying, wearable heaters, heat therapy, wearable strain sensors, respiratory monitoring, gait monitoring, health monitoring, flexible electronics
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.