Enzymatic Hydrolysis Combined with Mechanical Shearing and High-Pressure Homogenization for Nanoscale Cellulose Fibrils and Strong Gels
The DOI matches its Crossref record; 23 of the 23 references it cites were found in a registry or an index.
Abstract
Toward exploiting the attractive mechanical properties of cellulose I nanoelements, a novel route is demonstrated, which combines enzymatic hydrolysis and mechanical shearing. Previously, an aggressive acid hydrolysis and sonication of cellulose I containing fibers was shown to lead to a network of weakly hydrogen-bonded rodlike cellulose elements typically with a low aspect ratio. On the other hand, high mechanical shearing resulted in longer and entangled nanoscale cellulose elements leading to stronger networks and gels. Nevertheless, a widespread use of the latter concept has been hindered because of lack of feasible methods of preparation, suggesting a combination of mild hydrolysis and shearing to disintegrate cellulose I containing fibers into high aspect ratio cellulose I nanoscale elements. In this work, mild enzymatic hydrolysis has been introduced and combined with mechanical shearing and a high-pressure homogenization, leading to a controlled fibrillation down to nanoscale and a network of long and highly entangled cellulose I elements. The resulting strong aqueous gels exhibit more than 5 orders of magnitude tunable storage modulus G' upon changing the concentration. Cryotransmission electron microscopy, atomic force microscopy, and cross-polarization/magic-angle spinning (CP/MAS) 13C NMR suggest that the cellulose I structural elements obtained are dominated by two fractions, one with lateral dimension of 5-6 nm and one with lateral dimensions of about 10-20 nm. The thicker diameter regions may act as the junction zones for the networks. The resulting material will herein be referred to as MFC (microfibrillated cellulose). Dynamical rheology showed that the aqueous suspensions behaved as gels in the whole investigated concentration range 0.125-5.9% w/w, G' ranging from 1.5 Pa to 105 Pa. The maximum G' was high, about 2 orders of magnitude larger than typically observed for the corresponding nonentangled low aspect ratio cellulose I gels, and G' scales with concentration with the power of approximately three. The described preparation method of MFC allows control over the final properties that opens novel applications in materials science, for example, as reinforcement in composites and as templates for surface modification.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“Compared to the more aggressive acid hydrolysis treatment, the enzymatic treatment yielded longer and highly entangled nanoscale fibrils.”
From Cellulosic Bionanocomposites: A Review of Preparation, Properties and Applications (2010) · cites this paper as [84]
In the citing paper
“Finally, the enzymatic step leads to reduced energy consumption allowing widespread use of the material”
From Cellulosic Bionanocomposites: A Review of Preparation, Properties and Applications (2010) · cites this paper as [84]
In the citing paper
“They demonstrated that the enzymatic hydrolysis step avoids blocking problems during the homogenization treatment.”
From Cellulosic Bionanocomposites: A Review of Preparation, Properties and Applications (2010) · cites this paper as [84]
In the citing paper
“Xylanases are hydrolytic enzymes that modify the random amorphous compounds (hemicelluloses) present in the plant fiber.”
From Cellulose nanofibers produced from banana peel by chemical and enzymatic treatment (2014) · cites this paper as Pääkko et al., 2007
In the citing paper
“They can also initiate the random hydrolysis of the b-1,4 non-reducing terminal regions located between the glycosidic linkages of the glucose units (Hubbe, Rojas, Lucia, & Sain, 2008;Pääkko et al., 2007).”
From Cellulose nanofibers produced from banana peel by chemical and enzymatic treatment (2014) · cites this paper as Pääkko et al., 2007
1 more claim about this paper
Create a free account to see every claim other papers make about this one.
Citations
Cites
Scaling concepts in polymer physics
Gordon, M. (1981) · Polymer · doi:10.1016/0032-3861(81)90183-x · Cited by 10,288
Scaling Concepts in Polymer Physics
de Gennes, P. G., & Witten, T. A. (1980) · Physics Today · doi:10.1063/1.2914118 · Cited by 9,348
Numerical Recipes: The Art of Scientific Computing
Ziegel, E. (1987) · Technometrics · doi:10.1080/00401706.1987.10488304 · Cited by 6,702
Saito, T., Nishiyama, Y., Putaux, J.-L., Vignon, M., & Isogai, A. (2006) · Biomacromolecules · doi:10.1021/bm060154s · Cited by 1,796
Native cellulose: A composite of two distinct crystalline forms
Atalla, R. H., & VanderHart, D. L. (1984) · Science · doi:10.1126/science.223.4633.283 · Cited by 1,196
Natural Fibers, Biopolymers, and Biocomposites: An Introduction
Mohanty, A., Misra, M., Drzal, L., Selke, S., Harte, B., & Hinrichsen, G. (2005) · Natural Fibers, Biopolymers, and Biocomposites · doi:10.1201/9780203508206.ch1 · Cited by 976
Dynamics of concentrated polymer systems. Part 3.—The constitutive equation
Doi, M., & Edwards, S. F. (1978) · J. Chem. Soc., Faraday Trans. 2 · doi:10.1039/f29787401818 · Cited by 615
Assignment of non-crystalline forms in cellulose I by CP/MAS 13C NMR spectroscopy
Wickholm, K., Larsson, P. T., & Iversen, T. (1998) · Carbohydrate Research · doi:10.1016/s0008-6215(98)00236-5 · Cited by 423
Self-citationA CP/MAS13C NMR investigation of molecular ordering in celluloses
Larsson, P. T., Wickholm, K., & Iversen, T. (1997) · Carbohydrate Research · doi:10.1016/s0008-6215(97)00130-4 · Cited by 399
Self-citationChemical Modification of Lignocellulosic Materials
(2017) · Routledge eBooks · doi:10.1201/9781315139142 · Cited by 339
Research works printed but not linked: 28
- Hult E. L., 2001, Polymer, 42, 3314
- Hult E. L., 2002, Holzforschung, 56, 184
- Liu H., 2002, Part B: Polym. Phys
- Kim C.-W., 2006, Polymer, 47, 5107
- Fleming K., 2001, ChemEur. J., 7, 1835
- Lima M. M. D., 2004, Macromol. Rapid Commun., 25, 787
- Araki J., 1998, Physicochem. Eng. Aspects
- Turbak A. F., 1983, Appl. Polym. Symp.
- Herrick F. W., 1983, Appl. Polym. Symp.
- Nakagaito A. N., 2004, Process
- Berglund L. A., 2005, Natural Fibers, Biopolymers, and Biocomposites
- Nakagaito A. N., 2005, Process
- Nakagaito A. N., 2005, Process
- Henriksson M., 2007, Eur. Polym. J.
- Ono H., 2004, Polym. J., 36, 694
- Tatsumi D., 2002, J. Soc. Rheol., Jpn., 30, 32
- Rudraraju V. S., 2005, Int. J. Pharm., 292, 61
- Rudraraju V. S., 2005, Int. J. Pharm., 292, 73
- Lowys M.-P., 2001, Food Hydrocolloids, 15, 32
- Ono H., 1998, Cellulose, 5, 247
- Ono H., 2001, Trans. Mater. Res. Soc. Jpn., 26, 572
- Engström A.-C., 2006, Biomacromolecules, 7, 2031
- Hausalo T., 1999, Pulp and Paper Testing, 63
- Hiltunen E., 1999, Pulp and Paper Testing, 135
- Katz K., 1984, Sven. Papperstid., 87, R48
- Guenet J.-M., 2000, J. Rheol., 44, 960
- Sahimi M., 1998, Phys. Rep., 306, 395
- Soft Matter Physics, 1999, Springer-Verlag: Berlin
Cited by
Items 401–500 of 1,002
Pretreatment-dependent surface chemistry of wood nanocellulose for pH-sensitive hydrogels
Chinga‐Carrasco, G., & Syverud, K. (2014) · Journal of Biomaterials Applications · doi:10.1177/0885328214531511 · Cited by 111
“Pre-treatments, which are applied to facilitate the fibrillation of cellulose fibres, involve mechanical, enzymatic and chemical pre-treatments.(1,2,10) Mechanical and enzymatic pre-treatments preserve the surface chemistry of cellulose fibres, i.”
MethodVersatile Gas-Phase Reactions for Surface to Bulk Esterification of Cellulose Microfibrils Aerogels
Fumagalli, M., Ouhab, D., Molina-Boisseau, S., & Heux, L. (2013) · Biomacromolecules · doi:10.1021/bm400864z · Cited by 123
Using Commercial Enzymes to Produce Cellulose Nanofibers from Soybean Straw
Martelli‐Tosi, M., Torricillas, M. D. S., Martins, M. A., ASSIS, O. B. G., & Tapia‐Blácido, D. R. (2016) · Journal of Nanomaterials · doi:10.1155/2016/8106814 · Cited by 114
“Some authors have focused on the preparation of microfibrillated cellulose [16, 17].”
BackgroundEffect of precipitated calcium carbonate—Cellulose nanofibrils composite filler on paper properties
He, M. H., Cho, B., & Won, J. M. (2015) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2015.09.069 · Cited by 112
Al‐Sabah, A., Burnell, S. E. A., Simões, I. N., Jessop, Z. M., Badiei, N., Blain, E. J., & Whitaker, I. S. (2019) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2019.02.057 · Cited by 107
Overview of nanocellulose as additives in paper processing and paper products
Li, A., Xu, D., Luo, L., Zhou, Y., Wen, Y. F., Leng, X., Dai, D., Zhou, Y., Ahmad, H., Rao, J., et al. (2021) · Nanotechnology Reviews · doi:10.1515/ntrev-2021-0023 · Cited by 116
Preparation of cross-linked cellulose nanofibril aerogel with water absorbency and shape recovery
Kim, C. H., Youn, H. J., & Lee, H. L. (2015) · Cellulose · doi:10.1007/s10570-015-0745-5 · Cited by 107
“Another promising application of CNF is to prepare cellulose aerogel (Pääkkö et al. 2008).”
BackgroundTemperature stability of nanocellulose dispersions
Heggset, E. B., Chinga‐Carrasco, G., & Syverud, K. (2016) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2016.09.077 · Cited by 110
Nanocellulosic materials as bioinks for 3D bioprinting
Piras, C. C., Fernández‐Prieto, S., & Borggraeve, W. M. D. (2017) · Biomaterials Science · doi:10.1039/c7bm00510e · Cited by 110
Isolation of cellulose nanofibrils from Triodia pungens via different mechanical methods
Amiralian, N., Annamalai, P. K., Memmott, P. C., & Martin, D. J. (2015) · Cellulose · doi:10.1007/s10570-015-0688-x · Cited by 108
Syverud, K., Xhanari, K., Chinga‐Carrasco, G., Yu, Y., & Stenius, P. J. (2010) · Journal of Nanoparticle Research · doi:10.1007/s11051-010-0077-1 · Cited by 124
Rosilo, H., Kontturi, E., Seitsonen, J. J. T., Kolehmainen, E. T., & Ikkala, O. T. (2013) · Biomacromolecules · doi:10.1021/bm400185z · Cited by 111
Self-citationPahimanolis, N., Hippi, U., Johansson, L., Saarinen, T., Houbenov, N., Ruokolainen, J., & Seppälä, J. V. (2011) · Cellulose · doi:10.1007/s10570-011-9573-4 · Cited by 121
“increasing shear rate and, at rest, a gel-like behavior with storage modulus G0 being higher than loss modulus G00 (Agoda-Tandjawa et al. 2010; Pääkkö et al. 2007).”
BackgroundSelf-citationComposites of nanofibrillated cellulose with clay minerals: A review
Alves, L., Ferraz, E., & Gamelas, J. A. F. (2019) · Advances in Colloid and Interface Science · doi:10.1016/j.cis.2019.101994 · Cited by 113
Padzil, F. N. M., Lee, S. H., Ainun, Z. M. A., Lee, C. H., & Abdullah, L. C. (2020) · Materials · doi:10.3390/ma13051245 · Cited by 122
“’s (2007) research group was the first group to show that a CNF hydrogel was possible at low concentration, followed with enzymatic and homogenization treatments [47].”
BackgroundJiménez-Saelices, C., Seantier, B., Cathala, B., & Grohens, Y. (2017) · Journal of Sol-Gel Science and Technology · doi:10.1007/s10971-017-4451-7 · Cited by 104
Assembling and Redispersibility of Rice Straw Nanocellulose: Effect of tert-Butanol
Jiang, F., & Hsieh, Y. (2014) · ACS Applied Materials & Interfaces · doi:10.1021/am505626a · Cited by 104
Nanocellulose Mechanically Isolated from Amorpha fruticosa Linn.
Zhuo, X., Liu, C., Pan, R., Dong, X., & Li, Y. (2017) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.7b00478 · Cited by 102
Basu, A., Heitz, K., Strømme, M., Welch, K., & Ferraz, N. (2017) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2017.10.085 · Cited by 103
Tamo, A. K., Doench, I., Deffo, G., Jiokeng, S. L. Z., Doungmo, G., Fotsop, C. G., Temgoua, R. C. T., Montembault, A., Serghei, A., Njanja, E., et al. (2025) · Journal of Materials Chemistry A · doi:10.1039/d5ta02900g · Cited by 120
Effect of polymer adsorption on cellulose nanofibril water binding capacity and aggregation
Ahola, S., Myllytie, P., Österberg, M., Teerinen, T., & Laine, J. (2008) · BioResources · doi:10.15376/biores.3.4.1315-1328 · Cited by 99
“High aspect ratio and specific surface area combined with high strength and flexibility are characteristic for cellulose nanofibrils (Pääkkö et al. 2007).”
BackgroundMethodInfluentialSelf-citationPlappert, S. F., Nédélec, J., Rennhofer, H., Lichtenegger, H. C., & Liebner, F. W. (2017) · Chemistry of Materials · doi:10.1021/acs.chemmater.7b00787 · Cited by 106
Production of cellulose nanocrystals via a scalable mechanical method
Amin, K. N. M., Annamalai, P. K., Morrow, I. C., & Martin, D. J. (2015) · RSC Advances · doi:10.1039/c5ra06862b · Cited by 107
Hiraoki, R., Ono, Y., Saito, T., & Isogai, A. (2015) · Biomacromolecules · doi:10.1021/bm501857c · Cited by 104
Lam, N. T., Chollakup, R., Smitthipong, W., Nimchua, T., & Sukyai, P. (2017) · Industrial Crops and Products · doi:10.1016/j.indcrop.2017.02.031 · Cited by 101
Huang, Z., Zhang, H., Guo, M., Zhao, M., Liu, Y., Zhang, D., Terrones, M., & Wang, Y. (2022) · Carbon · doi:10.1016/j.carbon.2022.03.056 · Cited by 99
Multifunctional Coating Films by Layer-by-Layer Deposition of Cellulose and Chitin Nanofibrils
Qi, Z.-D., Saito, T., Fan, Y., & Isogai, A. (2012) · Biomacromolecules · doi:10.1021/bm201659b · Cited by 102
Holocellulose Nanofibers of High Molar Mass and Small Diameter for High-Strength Nanopaper
Galland, S., Berthold, F., Prakobna, K., & Berglund, L. A. (2015) · Biomacromolecules · doi:10.1021/acs.biomac.5b00678 · Cited by 106
Doench, I., Torres-Ramos, M., Montembault, A., Oliveira, P. F., Halimi, C., Viguier, É., Heux, L., Siadous, R., Thiré, R. M. D. S. M., & Osorio‐Madrazo, A. (2018) · Polymers · doi:10.3390/polym10111202 · Cited by 102
“[47], i ic a ec a o-e z atic rol sis lea es lo nanoscale fibrils preserving the native cellulose I crystalline allomorph with partly amorphous regions, which nanofibrils are able to inherently entangle.”
BackgroundMethodInfluentialdos Santos, S. F., Tonoli, G. H. D., Mejia, J., Fiorelli, J., & Savastano, H. (2015) · Materiales de Construcción · doi:10.3989/mc.2015.05514 · Cited by 116
Masruchin, N., Park, B., Causin, V., & Um, I. C. (2015) · Cellulose · doi:10.1007/s10570-015-0624-0 · Cited by 107
“In general, CNW, shaped as rod-like whiskers, are isolated from woody cellulose by acid hydrolysis, which removes the amorphous region of the cellulose to isolate the crystalline CNW component (Renneckar et al. 2006; Paakko et al. 2007).”
BackgroundIndividual cotton cellulose nanofibers: pretreatment and fibrillation technique
Chen, W., Abe, K., Uetani, K., Yu, H., Li, P., & Yano, H. (2014) · Cellulose · doi:10.1007/s10570-014-0172-z · Cited by 99
“Since hemicelluloses are removed from cellulose pulp with difficulty, even upon alkali (Iwamoto et al. 2008), acid (Chen et al. 2011b), or enzyme (Pääkkö et al. 2007) treatments, the production of high purity CNFs remains a significant challenge.”
Sehaqui, H., Morimune, S., Nishino, T., & Berglund, L. A. (2012) · Biomacromolecules · doi:10.1021/bm301105s · Cited by 105
Nanocellulosen: eine neue Familie naturbasierter Materialien
Klemm, D., Kramer, F., Moritz, S., Lindström, T., Ankerfors, M., Gray, D. G., & Dorris, A. (2011) · Angewandte Chemie · doi:10.1002/ange.201001273 · Cited by 98
Self-citationStimuli-Responsive Polysaccharide Hydrogels for Biomedical Applications: a Review
Gholamali, I. (2019) · Regenerative Engineering and Translational Medicine · doi:10.1007/s40883-019-00134-1 · Cited by 105
“Further, BC displays many advantages over cellulose obtained from different sources that might require enzymatic [40], mechanical [41], mixed [42], and expen-”
BackgroundHighly absorbent cellulose nanofibrils aerogels prepared by supercritical drying
Darpentigny, C., Nonglaton, G., Bras, J., & Jean, B. (2019) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2019.115560 · Cited by 99
Nanocellulose from agro-waste: a comprehensive review of extraction methods and applications
Padhi, S., Singh, A., & Routray, W. (2023) · Reviews in Environmental Science and Bio/Technology · doi:10.1007/s11157-023-09643-6 · Cited by 108
Celluloses and Polyoses/Hemicelluloses
Heinze, T. J., & Liebert, T. F. (2012) · Elsevier eBooks · doi:10.1016/b978-0-444-53349-4.00255-7 · Cited by 111
Extraction and characterization of cellulose whiskers from commercial cotton fibers
Martins, M. A., Teixeira, E. M., Corrêa, A. C., Ferreira, M., & Mattoso, L. H. C. (2011) · Journal of Materials Science · doi:10.1007/s10853-011-5767-2 · Cited by 106
Drying and redispersion of plant cellulose nanofibers for industrial applications: a review
Posada, P., Velásquez-Cock, J. A., Hoyos, C. G., Serpa, A., Lyulin, S. V., Kenny, J. M., Gañán, P. F., Castro, C. I., & Zuluaga, R. (2020) · Cellulose · doi:10.1007/s10570-020-03348-7 · Cited by 101
Transparent, water-stable, cellulose nanofiber-based packaging film with a low oxygen permeability
Kim, J., Choi, B., & Jin, J. (2020) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2020.116823 · Cited by 100
Application of Nanotechnology in Wood-Based Products Industry: A Review
Jasmani, L., Rusli, R., Khadiran, T., Jalil, R., & Adnan, S. (2020) · Nanoscale Research Letters · doi:10.1186/s11671-020-03438-2 · Cited by 101
Mechanochemical Transformations of Biomass into Functional Materials
Hajiali, F., Jin, T., Yang, G., Santos, M., Lam, E., & Moores, A. (2022) · ChemSusChem · doi:10.1002/cssc.202102535 · Cited by 99
Harvesting energy from extreme environmental conditions with cellulosic triboelectric materials
Shao, Y., Luo, B., Liu, T., Cai, C., Meng, X., Wang, S., & Nie, S. (2023) · Materials Today · doi:10.1016/j.mattod.2023.04.006 · Cited by 99
Characterization of highly accessible cellulose microfibers generated by wet stirred media milling
Liimatainen, H., Sirviö, J. A., Haapala, A., Hormi, O. E. O., & Niinimäki, J. (2010) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2010.11.007 · Cited by 97
Vapour-driven Marangoni propulsion: continuous, prolonged and tunable motion
Jin, H., Marmur, A., Ikkala, O. T., & Ras, R. H. A. (2012) · Chemical Science · doi:10.1039/c2sc20355c · Cited by 95
Self-citationTanaka, R., Saito, T., Hondo, H., & Isogai, A. (2015) · Biomacromolecules · doi:10.1021/acs.biomac.5b00539 · Cited by 102
The effect of MFC on the pressability and paper properties of TMP and GCC based sheets
Hii, C., Gregersen, Ø. W., Chinga‐Carrasco, G., & Eriksen, Ø. (2012) · Nordic Pulp & Paper Research Journal · doi:10.3183/npprj-2012-27-02-p388-396 · Cited by 107
“MFC has been prepared by mechanically disintegrating cellulose fibres through homogenization (Turbak et al. 1983; Herrick et al. 1983; Pääkkö et al. 2007; Syverud et al. 2011), grinding (Iwamoto et al. 2005; Iwamoto et al. 2007; Eriksen et al. 2008; Abe, Yano 2009), fluidization (Taipale et al.…”
BackgroundMethodInfluentialNovel Trends in Lyotropic Liquid Crystals
Dierking, I., & Neto, A. M. F. (2020) · Crystals · doi:10.3390/cryst10070604 · Cited by 108
“CNCs are stiff, lath-like nanoparticles, with a typical diameter as small as ~6 nm, depending on the preparation method [63], and a length of about 100 nm.”
BackgroundNanocellulose-based hydrogels as versatile drug delivery vehicles: A review
He, P., Dai, L., Wei, J., Zhu, X., Li, J., Chen, Z., & Ni, Y. (2022) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2022.09.214 · Cited by 100
Emenike, E. C., Iwuozor, K. O., Saliu, O. D., Ramontja, J., & Adeniyi, A. G. (2023) · Carbohydrate Polymer Technologies and Applications · doi:10.1016/j.carpta.2023.100337 · Cited by 129
Chalak, A., Villares, A., Moreau, C., Haon, M., Grisel, S., d’Orlando, A., Herpoël-Gimbert, I., Labourel, A., Cathala, B., & Berrin, J.-G. (2019) · Biotechnology for Biofuels · doi:10.1186/s13068-019-1548-y · Cited by 94
“Removal of the CBM attached to cellulases dramatically decreases the activity on insoluble substrates but not on soluble substrates [37, 42, 43].”
BackgroundCrystallinity-Independent yet Modification-Dependent True Density of Nanocellulose
Daicho, K., Kobayashi, K., Fujisawa, S., & Saito, T. (2019) · Biomacromolecules · doi:10.1021/acs.biomac.9b01584 · Cited by 103
Wang, S., Ma, H., Ge, S., Rezakazemi, M., & Han, J. (2025) · Materials Science and Engineering R Reports · doi:10.1016/j.mser.2025.100925 · Cited by 95
Onyianta, A. J., Dorris, M., & Williams, R. (2017) · Cellulose · doi:10.1007/s10570-017-1631-0 · Cited by 100
Surface treatment of cellulose nanocrystals (CNC): effects on dispersion rheology
Sahlin, K., Forsgren, L., Moberg, T., Bernin, D., Rigdahl, M., & Westman, G. (2017) · Cellulose · doi:10.1007/s10570-017-1582-5 · Cited by 98
Zhou, Q., Malm, E., Nilsson, H., Larsson, P. T., Iversen, T., Berglund, L. A., & Bulone, V. (2009) · Soft Matter · doi:10.1039/b907838j · Cited by 101
Self-citationThe structure and mechanics of nanofibrillar cellulose foams
Ali, Z. M., & Gibson, L. J. (2012) · Soft Matter · doi:10.1039/c2sm27197d · Cited by 102
“Due to the high aspect ratio, a very dilute suspension is needed in order to avoid gelation due to formation of an NFC network; the rheology of such suspensions has been studied by Paakko et al. (2007).”
BackgroundProduction and Characterization of Cellulose Nanofibers from Wood Pulp
Siddiqui, N., Mills, R. H., Gardner, D. J., & Bousfield, D. W. (2011) · Journal of Adhesion Science and Technology · doi:10.1163/016942410x525975 · Cited by 100
TEMPO-Oxidized Nanofibrillated Cellulose as a High Density Carrier for Bioactive Molecules
Weishaupt, R., Siqueira, G. D. F., Schubert, M., Tingaut, P., Maniura‐Weber, K., Zimmermann, T., Thöny‐Meyer, L., Faccio, G., & Ihssen, J. (2015) · Biomacromolecules · doi:10.1021/acs.biomac.5b01100 · Cited by 103
Green synthesis of cellulose nanofibers using immobilized cellulase
Yassin, M. A., Gad, A. A. M., Ghanem, A. F. M., & Rehim, M. H. A. (2018) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2018.10.040 · Cited by 91
Zheng, Q., Javadi, A., Sabo, R. C., Cai, Z., & Gong, S. (2013) · RSC Advances · doi:10.1039/c3ra42321b · Cited by 95
Properties of Nanocelluloses and Their Application as Rheology Modifier in Paper Coating
Liu, C., Du, H., Lv, D., Wang, X., Zhang, Y., Yu, G., Li, B., Mu, X., Peng, H. H., & Liu, H. (2017) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.7b01804 · Cited by 92
Fall, A. B., Lindström, S. B., Sprakel, J. H. B., & Wågberg, L. (2012) · Soft Matter · doi:10.1039/c2sm27223g · Cited by 90
High Solid Content Production of Nanofibrillar Cellulose via Continuous Extrusion
Baati, R., Magnin, A., & Boufi, S. (2017) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.6b02673 · Cited by 90
Arantes, V., Dias, I. K. R., Berto, G. L., Pereira, B., Marotti, B. D. S., & Nogueira, C. F. O. (2020) · Cellulose · doi:10.1007/s10570-020-03332-1 · Cited by 99
Exploring Large Ductility in Cellulose Nanopaper Combining High Toughness and Strength
Chen, F., Xiang, W., Sawada, D., Bai, L., Hummel, M., Sixta, H., & Budtova, T. (2020) · ACS Nano · doi:10.1021/acsnano.0c02302 · Cited by 90
Nanofibrillated cellulose/carboxymethyl cellulose composite with improved wet strength
Pahimanolis, N., Salminen, A., Penttilä, P. A., Korhonen, J. T., Johansson, L., Ruokolainen, J., Serimaa, R. E., & Seppälä, J. V. (2013) · Cellulose · doi:10.1007/s10570-013-9923-5 · Cited by 92
“All suspensions have a typical decreasing viscosity with increasing shear rate and, at rest, a gel-like behavior with storage modulus G0 being higher than loss modulus G00 (Pääkkö et al. 2007; Agoda-Tandjawa et al. 2010).”
BackgroundSelf-citationGamelas, J. A. F., Pedrosa, J. F. S., Lourenço, A. F., Mutjé, P., González, I., Chinga‐Carrasco, G., Singh, G., & Ferreira, P. J. (2015) · Micron · doi:10.1016/j.micron.2015.02.003 · Cited by 110
Lavoine, N., Bras, J., & Desloges, I. (2013) · Journal of Applied Polymer Science · doi:10.1002/app.40106 · Cited by 105
Alkaline treatment combined with enzymatic hydrolysis for efficient cellulose nanofibrils production
Banvillet, G., Déprès, G., Belgacem, M. N., & Bras, J. (2020) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2020.117383 · Cited by 95
Salehi, E., Khajavian, M., Sahebjamee, N., Mahmoudi, M., Drioli, E., & Matsuura, T. (2022) · Desalination · doi:10.1016/j.desal.2022.115565 · Cited by 90
Wu, J., Zhang, K., Girouard, N., & Meredith, J. C. (2014) · Biomacromolecules · doi:10.1021/bm501416q · Cited by 90
Ang, S., Haritos, V. S., & Batchelor, W. J. (2019) · Cellulose · doi:10.1007/s10570-019-02400-5 · Cited by 99
Kontturi, E., & Vuorinen, T. (2008) · Cellulose · doi:10.1007/s10570-008-9235-3 · Cited by 104
Assessing the combined benefits of clay and nanofibrillated cellulose in layered TMP-based sheets
Mörseburg, K., & Chinga‐Carrasco, G. (2009) · Cellulose · doi:10.1007/s10570-009-9290-4 · Cited by 106
Hybrid Supramolecular and Colloidal Hydrogels that Bridge Multiple Length Scales
Janeček, E., McKee, J. R., Tan, C. S. Y., Nykänen, A., Kettunen, M., Laine, J., Ikkala, O. T., & Scherman, O. A. (2015) · Angewandte Chemie International Edition · doi:10.1002/anie.201410570 · Cited by 91
Self-citationBakkari, M. E., Bindiganavile, V., Goncalves, J., & Boluk, Y. (2018) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2018.09.036 · Cited by 100
Effect of lignin and hemicellulose on the properties of lignocellulose nanofibril suspensions
Albornoz-Palma, G., Ching, D., Valerio, O., Mendonça, R. T., & Pereira, M. Á. (2020) · Cellulose · doi:10.1007/s10570-020-03304-5 · Cited by 91
Cranston, E. D., Eita, M., Johansson, E. E., Netrval, J., Salajková, M., Arwin, H., & Wågberg, L. (2011) · Biomacromolecules · doi:10.1021/bm101330w · Cited by 92
Rheological characterization of high concentrated MFC gel from kenaf unbleached pulp
Charani, P. R., Firouzabadi, M. D., Afra, E., & Shakeri, A. (2013) · Cellulose · doi:10.1007/s10570-013-9862-1 · Cited by 101
“…elastic behavior dominates, i.e., G0 G00, G0 & x0, and G00 & x0, and these relationships can be achieved by dispersing a sufficiently high concentration of physical or chemical network forming polymers within a solvent medium (Ross-Murphy 1994; Almdal et al. 1992; Burchard and Ross-Murphy 1990).”
A xylanase-aided enzymatic pretreatment facilitates cellulose nanofibrillation
Long, L., Tian, D., Hu, J., Wang, F., & Saddler, J. N. (2017) · Bioresource Technology · doi:10.1016/j.biortech.2017.07.037 · Cited by 93
Potential of municipal solid waste paper as raw material for production of cellulose nanofibres
Hietala, M., Kalle, V., Berglund, L., Soini, J., & Oksman, K. (2018) · Waste Management · doi:10.1016/j.wasman.2018.09.033 · Cited by 87
Wu, W. H., Tassi, N. G., Zhu, H., Fang, Z., & Hu, L. (2015) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.5b09249 · Cited by 90
Lytic polysaccharide monooxygenases (LPMOs) facilitate cellulose nanofibrils production
Moreau, C., Tapin‐Lingua, S., Grisel, S., Herpoël‐Gimbert, I., Gall, S. L., Meyer, V., Petit‐Conil, M., Berrin, J., Cathala, B., & Villares, A. (2019) · Biotechnology for Biofuels · doi:10.1186/s13068-019-1501-0 · Cited by 97
Comparison Of Mechanical And Chemical Nanocellulose As Additives To Reinforce Recycled Cardboard
Sanchez-Salvador, J. L., Balea, A., Monte, M. C., Negro, C., Miller, M., Olson, J. A., & Blanco, Á. (2020) · Scientific Reports · doi:10.1038/s41598-020-60507-3 · Cited by 93
Tamo, A. K., Doench, I., Walter, L., Montembault, A., Sudre, G., David, L., Helguera, A. M., Selig, M., Rolauffs, B., Bernstein, A., et al. (2021) · Polymers · doi:10.3390/polym13101663 · Cited by 92
“T e relatively high value of this la ter could be related to th drying during TEM sample pre aration, which might induce partial fibril aggregation [74].”
BackgroundMethodInfluentialNanocrystalline cellulose extracted from bast fibers: Preparation, characterization, and application
Shen, P., Tang, Q., Chen, X., & Li, Z. (2022) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2022.119462 · Cited by 95
Nanocellulose: An amazing nanomaterial with diverse applications in food science
Zhang, F., Shen, R., Li, N., Yang, X., & Lin, D. (2022) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2022.120497 · Cited by 92
Extraction and Characterization of Nanocellulose from Corn Stover
Costa, L. A. S., Assis, D. D. J., Gomes, G. V. P., da Silva, J. B. A., Fonsêca, A. F., & Druzian, J. I. (2015) · Materials Today Proceedings · doi:10.1016/j.matpr.2015.04.045 · Cited by 97
Hassan, M. L., Hassan, E. A., & Oksman, K. (2010) · Journal of Materials Science · doi:10.1007/s10853-010-4992-4 · Cited by 94
Wang, M., Olszewska, A., Walther, A., Malho, J., Schacher, F. H., Ruokolainen, J., Ankerfors, M., Laine, J., Berglund, L. A., Österberg, M., et al. (2011) · Biomacromolecules · doi:10.1021/bm101561m · Cited by 97
Self-citationModification of insoluble dietary fibres in soya bean okara and their physicochemical properties
Huang, S., He, Y., Zou, Y., & Liu, Z. (2015) · International Journal of Food Science & Technology · doi:10.1111/ijfs.12929 · Cited by 89
Sajab, M. S., Chia, C. H., Chan, C. H., Zakaria, S., Kaco, H., Chook, S. W., Chin, S. X., & Noor, A. M. (2016) · RSC Advances · doi:10.1039/c5ra26193g · Cited by 86
Recent advances in wood-based electrode materials for supercapacitors
Wei, S. M., Wan, C., & Wu, Y. (2023) · Green Chemistry · doi:10.1039/d2gc04271a · Cited by 88
Cellulose derivatives as environmentally-friendly additives in water-based drilling fluids: A review
Khan, M. A., Li, M., Lv, K., Sun, J., Liu, C., Liu, X., Shen, H., Dai, L., & Lalji, S. M. (2024) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2024.122355 · Cited by 94
Nanofibrillated cellulose surface grafting in ionic liquid
Missoum, K., Belgacem, M. N., Barnes, J., Brochier-Salon, M.-C., & Bras, J. (2012) · Soft Matter · doi:10.1039/c2sm25691f · Cited by 93
Chen, W., Li, Q., Cao, J., Li, P., Li, J., Zhang, J., Luo, S., & Yu, H. (2014) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2014.10.024 · Cited by 85
Obtaining nanocomposites of polyamide 6 and cellulose whiskers via extrusion and injection molding
Corrêa, A. C., Teixeira, E. D. M., Carmona, V. B., Teodoro, K. B. R., Ribeiro, C., Mattoso, L. H. C., & Marconcini, J. M. (2013) · Cellulose · doi:10.1007/s10570-013-0132-z · Cited by 83
Nanocellulose obtained from residues of peach palm extraction (Bactris gasipaes)
Franco, T. S., Potulski, D. C., Viana, L. M. M., de Andrade, E. F., de Andrade, A. S., & de Muñiz, G. I. B. (2019) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2019.04.035 · Cited by 91
Metadata
- Authors
- Pääkkö, M., Ankerfors, M., Kosonen, H., Nykänen, A., Ahola, S., Österberg, M., Ruokolainen, J., Laine, J., Larsson, P. T., Ikkala, O., & Lindström, T.
- Affiliations
- Trinity College Dublin (IE)
- Corresponding author
- Ikkala, O.
- Lindström, T.
- Venue
- Biomacromolecules
- Publisher
- American Chemical Society (ACS)
- Published
- 2007-05-03
- Volume
- 8
- Issue
- 6
- Pages
- 1934-1941
- ISSN
- 1525-7797 (ISSN-L)
- 1526-4602
- OpenAlex
- W2001245625
- Cited by
- 1,962
- References
- 23
- Citations by year
- 2026: 54 · 2025: 65 · 2024: 65 · 2023: 99 · 2022: 130 · 2021: 127 · 2020: 164 · 2019: 145 · 2018: 144 · 2017: 178 · 2016: 126 · 2015: 146 · 2014: 133 · 2013: 105 · 2012: 93
- FWCI
- 17.59
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Biomacromolecules (publishedVersion)
- PubMed (publishedVersion)
- Funders
- VINNOVA
- Topics
- Physical Sciences › Materials Science › Biomaterials › Advanced Cellulose Research Studies
- Life Sciences › Agricultural and Biological Sciences › Food Science › Polysaccharides Composition and Applications
- Life Sciences › Agricultural and Biological Sciences › Plant Science › Polysaccharides and Plant Cell Walls
- Keywords
- microfibrillated cellulose, enzymatic hydrolysis, mechanical shearing, high-pressure homogenization, cellulose fibrillation, cellulose gels, storage modulus, cellulose reinforcement
- MeSH terms
- Cellulose, Gels, Hydrogen-Ion Concentration, Hydrolysis, Magnetic Resonance Spectroscopy, Rheology, Stress, Mechanical, Temperature, Viscosity, Wood, Microscopy, Atomic Force, Cryoelectron Microscopy, Microscopy, Electron, Transmission, Macromolecular Substances, Nanoparticles
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.