Enzymatic Hydrolysis Combined with Mechanical Shearing and High-Pressure Homogenization for Nanoscale Cellulose Fibrils and Strong Gels
The DOI matches its Crossref record; 23 of the 23 references it cites were found in a registry or an index.
Abstract
Toward exploiting the attractive mechanical properties of cellulose I nanoelements, a novel route is demonstrated, which combines enzymatic hydrolysis and mechanical shearing. Previously, an aggressive acid hydrolysis and sonication of cellulose I containing fibers was shown to lead to a network of weakly hydrogen-bonded rodlike cellulose elements typically with a low aspect ratio. On the other hand, high mechanical shearing resulted in longer and entangled nanoscale cellulose elements leading to stronger networks and gels. Nevertheless, a widespread use of the latter concept has been hindered because of lack of feasible methods of preparation, suggesting a combination of mild hydrolysis and shearing to disintegrate cellulose I containing fibers into high aspect ratio cellulose I nanoscale elements. In this work, mild enzymatic hydrolysis has been introduced and combined with mechanical shearing and a high-pressure homogenization, leading to a controlled fibrillation down to nanoscale and a network of long and highly entangled cellulose I elements. The resulting strong aqueous gels exhibit more than 5 orders of magnitude tunable storage modulus G' upon changing the concentration. Cryotransmission electron microscopy, atomic force microscopy, and cross-polarization/magic-angle spinning (CP/MAS) 13C NMR suggest that the cellulose I structural elements obtained are dominated by two fractions, one with lateral dimension of 5-6 nm and one with lateral dimensions of about 10-20 nm. The thicker diameter regions may act as the junction zones for the networks. The resulting material will herein be referred to as MFC (microfibrillated cellulose). Dynamical rheology showed that the aqueous suspensions behaved as gels in the whole investigated concentration range 0.125-5.9% w/w, G' ranging from 1.5 Pa to 105 Pa. The maximum G' was high, about 2 orders of magnitude larger than typically observed for the corresponding nonentangled low aspect ratio cellulose I gels, and G' scales with concentration with the power of approximately three. The described preparation method of MFC allows control over the final properties that opens novel applications in materials science, for example, as reinforcement in composites and as templates for surface modification.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“Compared to the more aggressive acid hydrolysis treatment, the enzymatic treatment yielded longer and highly entangled nanoscale fibrils.”
From Cellulosic Bionanocomposites: A Review of Preparation, Properties and Applications (2010) · cites this paper as [84]
In the citing paper
“Finally, the enzymatic step leads to reduced energy consumption allowing widespread use of the material”
From Cellulosic Bionanocomposites: A Review of Preparation, Properties and Applications (2010) · cites this paper as [84]
In the citing paper
“They demonstrated that the enzymatic hydrolysis step avoids blocking problems during the homogenization treatment.”
From Cellulosic Bionanocomposites: A Review of Preparation, Properties and Applications (2010) · cites this paper as [84]
In the citing paper
“Xylanases are hydrolytic enzymes that modify the random amorphous compounds (hemicelluloses) present in the plant fiber.”
From Cellulose nanofibers produced from banana peel by chemical and enzymatic treatment (2014) · cites this paper as Pääkko et al., 2007
In the citing paper
“They can also initiate the random hydrolysis of the b-1,4 non-reducing terminal regions located between the glycosidic linkages of the glucose units (Hubbe, Rojas, Lucia, & Sain, 2008;Pääkko et al., 2007).”
From Cellulose nanofibers produced from banana peel by chemical and enzymatic treatment (2014) · cites this paper as Pääkko et al., 2007
1 more claim about this paper
Create a free account to see every claim other papers make about this one.
Citations
Cites
Scaling concepts in polymer physics
Gordon, M. (1981) · Polymer · doi:10.1016/0032-3861(81)90183-x · Cited by 10,288
Scaling Concepts in Polymer Physics
de Gennes, P. G., & Witten, T. A. (1980) · Physics Today · doi:10.1063/1.2914118 · Cited by 9,348
Numerical Recipes: The Art of Scientific Computing
Ziegel, E. (1987) · Technometrics · doi:10.1080/00401706.1987.10488304 · Cited by 6,702
Saito, T., Nishiyama, Y., Putaux, J.-L., Vignon, M., & Isogai, A. (2006) · Biomacromolecules · doi:10.1021/bm060154s · Cited by 1,796
Native cellulose: A composite of two distinct crystalline forms
Atalla, R. H., & VanderHart, D. L. (1984) · Science · doi:10.1126/science.223.4633.283 · Cited by 1,196
Natural Fibers, Biopolymers, and Biocomposites: An Introduction
Mohanty, A., Misra, M., Drzal, L., Selke, S., Harte, B., & Hinrichsen, G. (2005) · Natural Fibers, Biopolymers, and Biocomposites · doi:10.1201/9780203508206.ch1 · Cited by 976
Dynamics of concentrated polymer systems. Part 3.—The constitutive equation
Doi, M., & Edwards, S. F. (1978) · J. Chem. Soc., Faraday Trans. 2 · doi:10.1039/f29787401818 · Cited by 615
Assignment of non-crystalline forms in cellulose I by CP/MAS 13C NMR spectroscopy
Wickholm, K., Larsson, P. T., & Iversen, T. (1998) · Carbohydrate Research · doi:10.1016/s0008-6215(98)00236-5 · Cited by 423
Self-citationA CP/MAS13C NMR investigation of molecular ordering in celluloses
Larsson, P. T., Wickholm, K., & Iversen, T. (1997) · Carbohydrate Research · doi:10.1016/s0008-6215(97)00130-4 · Cited by 399
Self-citationChemical Modification of Lignocellulosic Materials
(2017) · Routledge eBooks · doi:10.1201/9781315139142 · Cited by 339
Research works printed but not linked: 28
- Hult E. L., 2001, Polymer, 42, 3314
- Hult E. L., 2002, Holzforschung, 56, 184
- Liu H., 2002, Part B: Polym. Phys
- Kim C.-W., 2006, Polymer, 47, 5107
- Fleming K., 2001, ChemEur. J., 7, 1835
- Lima M. M. D., 2004, Macromol. Rapid Commun., 25, 787
- Araki J., 1998, Physicochem. Eng. Aspects
- Turbak A. F., 1983, Appl. Polym. Symp.
- Herrick F. W., 1983, Appl. Polym. Symp.
- Nakagaito A. N., 2004, Process
- Berglund L. A., 2005, Natural Fibers, Biopolymers, and Biocomposites
- Nakagaito A. N., 2005, Process
- Nakagaito A. N., 2005, Process
- Henriksson M., 2007, Eur. Polym. J.
- Ono H., 2004, Polym. J., 36, 694
- Tatsumi D., 2002, J. Soc. Rheol., Jpn., 30, 32
- Rudraraju V. S., 2005, Int. J. Pharm., 292, 61
- Rudraraju V. S., 2005, Int. J. Pharm., 292, 73
- Lowys M.-P., 2001, Food Hydrocolloids, 15, 32
- Ono H., 1998, Cellulose, 5, 247
- Ono H., 2001, Trans. Mater. Res. Soc. Jpn., 26, 572
- Engström A.-C., 2006, Biomacromolecules, 7, 2031
- Hausalo T., 1999, Pulp and Paper Testing, 63
- Hiltunen E., 1999, Pulp and Paper Testing, 135
- Katz K., 1984, Sven. Papperstid., 87, R48
- Guenet J.-M., 2000, J. Rheol., 44, 960
- Sahimi M., 1998, Phys. Rep., 306, 395
- Soft Matter Physics, 1999, Springer-Verlag: Berlin
Cited by
Cellulose nanomaterials review: structure, properties and nanocomposites
Moon, R. J., Martini, A., Nairn, J., Simonsen, J., & Youngblood, J. (2011) · Chemical Society Reviews · doi:10.1039/c0cs00108b · Cited by 6,756
Nanocelluloses: A New Family of Nature‐Based Materials
Klemm, D., Kramer, F., Moritz, S., Lindström, T., Ankerfors, M., Gray, D., & Dorris, A. (2011) · Angewandte Chemie International Edition · doi:10.1002/anie.201001273 · Cited by 4,465
Self-citationTEMPO-oxidized cellulose nanofibers
Isogai, A., Saito, T., & Fukuzumi, H. (2011) · Nanoscale · doi:10.1039/c0nr00583e · Cited by 3,179
Microfibrillated cellulose and new nanocomposite materials: a review
Siró, I., & Plackett, D. (2010) · Cellulose · doi:10.1007/s10570-010-9405-y · Cited by 2,883
“The manufacture of MFC is now generally performed by a mechanical treatment consisting of refining and high pressure homogenizing process steps (Nakagaito and Yano 2005; Pääkkö et al. 2007; Stenstad et al. 2008).”
MethodReview: current international research into cellulose nanofibres and nanocomposites
Eichhorn, S. J., Dufresne, A., Aranguren, M., Marcovich, N. E., Capadona, J. R., Rowan, S. J., Weder, C., Thielemans, W., Roman, M., Renneckar, S., et al. (2010) · Journal of Materials Science · doi:10.1007/s10853-009-3874-0 · Cited by 2,418
Lavoine, N., Desloges, I., Dufresne, A., & Bras, J. (2012) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2012.05.026 · Cited by 1,791
Nanocellulose, a Versatile Green Platform: From Biosources to Materials and Their Applications
Thomas, B., Raj, M. C., B, A. K., H, R. M., Joy, J., Moores, A., Drisko, G. L., & Sanchez, C. (2018) · Chemical Reviews · doi:10.1021/acs.chemrev.7b00627 · Cited by 1,714
Production of cellulose nanofibrils: A review of recent advances
Nechyporchuk, O., Belgacem, M. N., & Bras, J. (2016) · Industrial Crops and Products · doi:10.1016/j.indcrop.2016.02.016 · Cited by 1,687
Nanocellulose: a new ageless bionanomaterial
Dufresne, A. (2013) · Materials Today · doi:10.1016/j.mattod.2013.06.004 · Cited by 1,685
Green composites from sustainable cellulose nanofibrils: A review
Abdul Khalil, H. P. S., Bhat, A. H., & Ireana Yusra, A. F. (2012) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2011.08.078 · Cited by 1,573
Key advances in the chemical modification of nanocelluloses
Habibi, Y. (2014) · Chem. Soc. Rev. · doi:10.1039/c3cs60204d · Cited by 1,561
Wood-Derived Materials for Green Electronics, Biological Devices, and Energy Applications
Zhu, H., Luo, W., Ciesielski, P. N., Fang, Z., Zhu, J. Y., Henriksson, G., Himmel, M. E., & Hu, L. (2016) · Chemical Reviews · doi:10.1021/acs.chemrev.6b00225 · Cited by 1,532
Markstedt, K., Mantas, A., Tournier, I., Martínez Ávila, H., Hägg, D., & Gatenholm, P. (2015) · Biomacromolecules · doi:10.1021/acs.biomac.5b00188 · Cited by 1,528
Abdul Khalil, H. P. S., Davoudpour, Y., Islam, M. N., Mustapha, A., Sudesh, K., Dungani, R., & Jawaid, M. (2014) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2013.08.069 · Cited by 1,333
“Pääkkö et al. (2007) applied mild enzymatic hydrolysis combined with refining and homogenization to produce NFC from bleached softwood pulp.”
MethodReview of Hydrogels and Aerogels Containing Nanocellulose
De France, K. J., Hoare, T., & Cranston, E. D. (2017) · Chemistry of Materials · doi:10.1021/acs.chemmater.7b00531 · Cited by 1,344
Cellulosic Bionanocomposites: A Review of Preparation, Properties and Applications
Siqueira, G., Bras, J., & Dufresne, A. (2010) · Polymers · doi:10.3390/polym2040728 · Cited by 1,328
Cellulose Nanopaper Structures of High Toughness
Henriksson, M., Berglund, L. A., Isaksson, P., Lindström, T., & Nishino, T. (2008) · Biomacromolecules · doi:10.1021/bm800038n · Cited by 1,299
Self-citationPolylactide (PLA)-based nanocomposites
Raquez, J.-M., Habibi, Y., Murariu, M., & Dubois, P. (2013) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2013.05.014 · Cited by 1,209
Production of nanocrystalline cellulose from lignocellulosic biomass: Technology and applications
Brinchi, L., Cotana, F., Fortunati, E., & Kenny, J. M. (2013) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2013.01.033 · Cited by 1,121
Current characterization methods for cellulose nanomaterials
Foster, E. J., Moon, R. J., Agarwal, U. P., Bortner, M. J., Bras, J., Camarero-Espinosa, S., Chan, K. J., Clift, M. J. D., Cranston, E. D., Eichhorn, S. J., et al. (2018) · Chemical Society Reviews · doi:10.1039/c6cs00895j · Cited by 1,021
Chen, W., Yu, H., Liu, Y., Chen, P., Zhang, M., & Hai, Y. (2011) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2010.10.040 · Cited by 971
Cellulose nanocrystals: synthesis, functional properties, and applications
George, J., & S N, S. (2015) · Nanotechnology, Science and Applications · doi:10.2147/nsa.s64386 · Cited by 953
“A new concept to prepare cellulose nanomaterials was reported, whereby enzymatic hydrolysis was used in combination with mechanical shearing and high-pressure homogenization, leading to a controlled fibrillation down to the nanoscale, to produce cellulose nanomaterials with a diameter of ∼5–6 nm.(33) Bacterial CNCs we…”
Cellulose nanocrystals and cellulose nanofibrils based hydrogels for biomedical applications
Du, H., Liu, W., Zhang, M., Si, C., Zhang, X., & Li, B. (2019) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2019.01.020 · Cited by 949
Klemm, D., Cranston, E. D., Fischer, D., Gama, M., Kedzior, S. A., Kralisch, D., Kramer, F., Kondo, T., Lindström, T., Nietzsche, S., et al. (2018) · Materials Today · doi:10.1016/j.mattod.2018.02.001 · Cited by 936
Self-citationCellulosic nanocomposites: a review
(2008) · BioResources · doi:10.15376/biores.3.3.929-980 · Cited by 901
“High intensity ultrasonic treatments (Lima et al. 2004; Bondeson et al. 2006a; Cheng et al. 2007; Paakko et al. 2007; Wang et al. 2008) generally have been reported to yield shorter, less fibrillar particles of nano-cellulose in some cases (Paakko et al. 2007; Wang et al. 2008), though thin…”
BackgroundMethodInfluentialObtaining Cellulose Nanofibers with a Uniform Width of 15 nm from Wood
Abe, K., Iwamoto, S., & Yano, H. (2007) · Biomacromolecules · doi:10.1021/bm700624p · Cited by 885
Wågberg, L., Decher, G., Norgren, M., Lindström, T., Ankerfors, M., & Axnäs, K. (2008) · Langmuir · doi:10.1021/la702481v · Cited by 867
Self-citationJonoobi, M., Oladi, R., Davoudpour, Y., Oksman, K., Dufresne, A., Hamzeh, Y., & Davoodi, R. (2015) · Cellulose · doi:10.1007/s10570-015-0551-0 · Cited by 847
Cellulose: A Review of Water Interactions, Applications in Composites, and Water Treatment
Etale, A., Onyianta, A. J., Turner, S. R., & Eichhorn, S. J. (2023) · Chemical Reviews · doi:10.1021/acs.chemrev.2c00477 · Cited by 817
Kargarzadeh, H., Ahmad, I., Abdullah, I., Dufresne, A., Zainudin, S. Y., & Sheltami, R. M. (2012) · Cellulose · doi:10.1007/s10570-012-9684-6 · Cited by 838
Hydrophobic Nanocellulose Aerogels as Floating, Sustainable, Reusable, and Recyclable Oil Absorbents
Korhonen, J. T., Kettunen, M., Ras, R. H. A., & Ikkala, O. (2011) · ACS Applied Materials & Interfaces · doi:10.1021/am200475b · Cited by 817
Self-citationCellulose nanowhiskers: promising materials for advanced applications
Eichhorn, S. J. (2011) · Soft Matter · doi:10.1039/c0sm00142b · Cited by 782
Nanocellulose: a promising nanomaterial for advanced electrochemical energy storage
Chen, W., Yu, H., Lee, S.-Y., Wei, T., Li, J., & Fan, Z. (2018) · Chemical Society Reviews · doi:10.1039/c7cs00790f · Cited by 766
Extraction of nanocellulose fibrils from lignocellulosic fibres: A novel approach
Abraham, E., Deepa, B., Pothan, L. A., Jacob, M., Thomas, S., Cvelbar, U., & Anandjiwala, R. (2011) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2011.06.034 · Cited by 751
Progress of Polymers from Renewable Resources: Furans, Vegetable Oils, and Polysaccharides
Gandini, A., Lacerda, T. M., Carvalho, A. J. F., & Trovatti, E. (2016) · Chemical Reviews · doi:10.1021/acs.chemrev.5b00264 · Cited by 756
Oxygen and oil barrier properties of microfibrillated cellulose films and coatings
Aulin, C., Gällstedt, M., & Lindström, T. (2010) · Cellulose · doi:10.1007/s10570-009-9393-y · Cited by 749
Self-citationRecent advances in surface-modified cellulose nanofibrils
Rol, F., Belgacem, M. N., Gandini, A., & Bras, J. (2019) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2018.09.002 · Cited by 698
Advanced Materials through Assembly of Nanocelluloses
Kontturi, E., Laaksonen, P., Linder, M. B., Nonappa, Gröschel, A. H., Rojas, O. J., & Ikkala, O. (2018) · Advanced Materials · doi:10.1002/adma.201703779 · Cited by 664
Self-citationNanofibrillated Cellulose Surface Modification: A Review
Missoum, K., Belgacem, M., & Bras, J. (2013) · Materials · doi:10.3390/ma6051745 · Cited by 658
“Between two refining steps, [14] performed an enzymatic treatment with endoglucanase before passing the pulp slurry through the microfluidizer which promotes cell wall delamination, and thus prevents the z-shaped chamber in the microfluidizer from blocking or clogging.”
BackgroundMethodPääkkö, M., Vapaavuori, J., Silvennoinen, R., Kosonen, H., Ankerfors, M., Lindström, T., Berglund, L. A., & Ikkala, O. (2008) · Soft Matter · doi:10.1039/b810371b · Cited by 660
Self-citationSacui, I. A., Nieuwendaal, R. C., Burnett, D. J., Stranick, S. J., Jorfi, M., Weder, C., Foster, E. J., Olsson, R. T., & Gilman, J. W. (2014) · ACS Applied Materials & Interfaces · doi:10.1021/am500359f · Cited by 647
Preparation and characterization of cellulose nanocrystals from rice straw
Lu, P., & Hsieh, Y.-L. (2012) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2011.08.022 · Cited by 635
Bacterial cellulose in biomedical applications: A review
Picheth, G. F., Pirich, C. L., Sierakowski, M. R., Woehl, M. A., Sakakibara, C. N., de Souza, C. F., Martin, A. A., da Silva, R., & de Freitas, R. A. (2017) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2017.05.171 · Cited by 624
Biomass-Derived Sponge-like Carbonaceous Hydrogels and Aerogels for Supercapacitors
Wu, X.-L., Wen, T., Guo, H.-L., Yang, S., Wang, X., & Xu, A.-W. (2013) · ACS Nano · doi:10.1021/nn400566d · Cited by 630
“5 kPa which is much higher than that of the CNTs hydrogel,(25,26) graphene hydrogel,(16,24) carbonaceous fiber hydrogel,(1) andnanocellular hydrogel.(27) Cyclic stress strain curves show that both the hydrogel and aerogel”
BackgroundNanocellulose properties and applications in colloids and interfaces
Salas, C., Nypelö, T., Rodriguez-Abreu, C., Carrillo, C., & Rojas, O. J. (2014) · Current Opinion in Colloid & Interface Science · doi:10.1016/j.cocis.2014.10.003 · Cited by 612
Zhang, Z., Sèbe, G., Rentsch, D., Zimmermann, T., & Tingaut, P. (2014) · Chemistry of Materials · doi:10.1021/cm5004164 · Cited by 613
Wood-based nanotechnologies toward sustainability
Jiang, F., Li, T., Li, Y., Zhang, Y., Gong, A., Dai, J., Hitz, E., Luo, W., & Hu, L. (2018) · Advanced Materials · doi:10.1002/adma.201703453 · Cited by 599
Strength and barrier properties of MFC films
Syverud, K., & Stenius, P. (2009) · Cellulose · doi:10.1007/s10570-008-9244-2 · Cited by 592
Cationic surface functionalization of cellulose nanocrystals
Hasani, M., Cranston, E. D., Westman, G., & Gray, D. G. (2008) · Soft Matter · doi:10.1039/b806789a · Cited by 568
Starch-based nano-biocomposites
Xie, F., Pollet, E., Halley, P. J., & Avérous, L. (2013) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2013.05.002 · Cited by 550
Chen, W., Yu, H., Liu, Y., Hai, Y., Zhang, M., & Chen, P. (2011) · Cellulose · doi:10.1007/s10570-011-9497-z · Cited by 541
Rojo, E., Peresin, M. S., Sampson, W. W., Hoeger, I. C., Vartiainen, J., Laine, J., & Rojas, O. J. (2015) · Green Chemistry · doi:10.1039/c4gc02398f · Cited by 530
Self-citationHydrodynamic alignment and assembly of nanofibrils resulting in strong cellulose filaments
Håkansson, K. M. O., Fall, A. B., Lundell, F., Yu, S., Krywka, C., Roth, S. V., Santoro, G., Kvick, M., Prahl Wittberg, L., Wågberg, L., et al. (2014) · Nature Communications · doi:10.1038/ncomms5018 · Cited by 523
Nanocellulose in Thin Films, Coatings, and Plies for Packaging Applications: A Review
Hubbe, M. A., Ferrer, A., Tyagi, P., Yin, Y., Salas, C., Pal, L., & Rojas, O. J. (2017) · BioResources · doi:10.15376/biores.12.1.2143-2233 · Cited by 508
Advances in cellulose nanomaterials
Kargarzadeh, H., Mariano, M., Gopakumar, D., Ahmad, I., Thomas, S., Dufresne, A., Huang, J., & Lin, N. (2018) · Cellulose · doi:10.1007/s10570-018-1723-5 · Cited by 508
“For example, by combining mechanical treatment with chemical or enzymatic treatments, it is possible to decrease the energy consumption from 20,000–30,000 kWh/ton to around 1000 kWh/ton (Pääkkö et al. 2007).”
MethodStrong and Tough Cellulose Nanopaper with High Specific Surface Area and Porosity
Sehaqui, H., Zhou, Q., Ikkala, O., & Berglund, L. A. (2011) · Biomacromolecules · doi:10.1021/bm2008907 · Cited by 510
Self-citation“Smart” Materials Based on Cellulose: A Review of the Preparations, Properties, and Applications
Qiu, X., & Hu, S. (2013) · Materials · doi:10.3390/ma6030738 · Cited by 509
“homogenization [110], and the prepared aqueous gel was used to prepare nanocellulose aerogels by vacuum freeze-drying method [111].”
MethodThe Effect of Hemicelluloses on Wood Pulp Nanofibrillation and Nanofiber Network Characteristics
Iwamoto, S., Abe, K., & Yano, H. (2008) · Biomacromolecules · doi:10.1021/bm701157n · Cited by 505
Relationship between Length and Degree of Polymerization of TEMPO-Oxidized Cellulose Nanofibrils
Shinoda, R., Saito, T., Okita, Y., & Isogai, A. (2012) · Biomacromolecules · doi:10.1021/bm2017542 · Cited by 497
Chitin nanofibers: preparations, modifications, and applications
Ifuku, S., & Saimoto, H. (2012) · Nanoscale · doi:10.1039/c2nr30383c · Cited by 490
Cartilage Tissue Engineering by the 3D Bioprinting of iPS Cells in a Nanocellulose/Alginate Bioink
Nguyen, D., Hägg, D. A., Forsman, A., Ekholm, J., Nimkingratana, P., Brantsing, C., Kalogeropoulos, T., Zaunz, S., Concaro, S., Brittberg, M., et al. (2017) · Scientific Reports · doi:10.1038/s41598-017-00690-y · Cited by 484
Cellulose Nanoparticles: Structure–Morphology–Rheology Relationships
Li, M.-C., Wu, Q., Song, K., Lee, S., Qing, Y., & Wu, Y. (2015) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.5b00144 · Cited by 487
Biopolymer nanofibrils: Structure, modeling, preparation, and applications
Ling, S., Chen, W., Fan, Y., Zheng, K., Jin, K., Yu, H., Buehler, M. J., & Kaplan, D. L. (2018) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2018.06.004 · Cited by 463
Sehaqui, H., Salajková, M., Zhou, Q., & Berglund, L. A. (2010) · Soft Matter · doi:10.1039/b927505c · Cited by 462
Wood nanocelluloses: fundamentals and applications as new bio-based nanomaterials
Isogai, A. (2013) · Journal of Wood Science · doi:10.1007/s10086-013-1365-z · Cited by 443
Olivera, S., Muralidhara, H. B., Venkatesh, K., Guna, V. K., Gopalakrishna, K., & Kumar K., Y. (2016) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2016.08.017 · Cited by 447
Nanofibrillated cellulose: surface modification and potential applications
Kalia, S., Boufi, S., Celli, A., & Kango, S. (2014) · Colloid and Polymer Science · doi:10.1007/s00396-013-3112-9 · Cited by 443
Plant-derived nanostructures: types and applications
Mohammadinejad, R., Karimi, S., Iravani, S., & Varma, R. S. (2016) · Green Chemistry · doi:10.1039/c5gc01403d · Cited by 437
Osong, S. H., Norgren, S., & Engstrand, P. (2016) · Cellulose · doi:10.1007/s10570-015-0798-5 · Cited by 434
“A number of researchers have studied enzymatic pretreatment as an approach to producing MFC and NFC (Gonzalez et al. 2013; Ankerfors et al. 2013b; Martin-Sampedro et al. 2012; Henriksson et al. 2008; Ahola et al. 2008a; Pääkkö et al. 2007; Henriksson et al. 2007; Lindström et al. 2007).”
BackgroundMethodInfluentialGhanadpour, M., Carosio, F., Larsson, P. T., & Wågberg, L. (2015) · Biomacromolecules · doi:10.1021/acs.biomac.5b01117 · Cited by 435
Self-citationNanocellulose: Recent Fundamental Advances and Emerging Biological and Biomimicking Applications
Heise, K., Kontturi, E., Allahverdiyeva, Y., Tammelin, T., Linder, M. B., Nonappa, & Ikkala, O. (2021) · Advanced Materials · doi:10.1002/adma.202004349 · Cited by 425
Self-citationNanofibrillated cellulose from TEMPO-oxidized eucalyptus fibres: Effect of the carboxyl content
Besbes, I., Alila, S., & Boufi, S. (2011) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2010.12.052 · Cited by 421
Thermal stabilization of TEMPO-oxidized cellulose
Fukuzumi, H., Saito, T., Okita, Y., & Isogai, A. (2010) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2010.06.015 · Cited by 421
Nanofibrillar cellulose hydrogel promotes three-dimensional liver cell culture
Bhattacharya, M., Malinen, M. M., Lauren, P., Lou, Y.-R., Kuisma, S. W., Kanninen, L., Lille, M., Corlu, A., GuGuen-Guillouzo, C., Ikkala, O., et al. (2012) · Journal of Controlled Release · doi:10.1016/j.jconrel.2012.06.039 · Cited by 412
“Native plant derived nanofibers can be isolated from plant cell walls using intensive mechanical shearing combined with chemical and enzymatic pre-treatments or TEMPO oxidation [20,22,23].”
BackgroundSelf-citationCassava bagasse cellulose nanofibrils reinforced thermoplastic cassava starch
Teixeira, E. D. M., Pasquini, D., Curvelo, A. A. S., Corradini, E., Belgacem, M. N., & Dufresne, A. (2009) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2009.04.034 · Cited by 403
Fast Preparation Procedure for Large, Flat Cellulose and Cellulose/Inorganic Nanopaper Structures
Sehaqui, H., Liu, A., Zhou, Q., & Berglund, L. A. (2010) · Biomacromolecules · doi:10.1021/bm100490s · Cited by 400
Zheng, Q., Cai, Z., & Gong, S. (2014) · J. Mater. Chem. A · doi:10.1039/c3ta14642a · Cited by 393
Cellulose nanofibers from white and naturally colored cotton fibers
de Morais Teixeira, E., Corrêa, A. C., Manzoli, A., de Lima Leite, F., de Oliveira, C. R., & Mattoso, L. H. C. (2010) · Cellulose · doi:10.1007/s10570-010-9403-0 · Cited by 381
Chen, Y., Liu, C., Chang, P. R., Cao, X., & Anderson, D. P. (2009) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2008.11.030 · Cited by 384
Design and applications of man-made biomimetic fibrillar hydrogels
Prince, E., & Kumacheva, E. (2019) · Nature Reviews Materials · doi:10.1038/s41578-018-0077-9 · Cited by 379
Polymeric gels and hydrogels for biomedical and pharmaceutical applications
Jagur‐Grodzinski, J. (2010) · Polymers for Advanced Technologies · doi:10.1002/pat.1504 · Cited by 383
Abe, K., & Yano, H. (2009) · Cellulose · doi:10.1007/s10570-009-9334-9 · Cited by 380
Basic effects of pulp refining on fiber properties—A review
Gharehkhani, S., Sadeghinezhad, E., Kazi, S. N., Yarmand, H., Badarudin, A., Safaei, M. R., & Zubir, M. N. M. (2015) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2014.08.047 · Cited by 367
Cellulose Nanoparticles as Modifiers for Rheology and Fluid Loss in Bentonite Water-based Fluids
Li, M.-C., Wu, Q., Song, K., Qing, Y., & Wu, Y. (2015) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.5b00498 · Cited by 373
Isolation, preparation, and characterization of nanofibers from oil palm empty-fruit-bunch (OPEFB)
Fahma, F., Iwamoto, S., Hori, N., Iwata, T., & Takemura, A. (2010) · Cellulose · doi:10.1007/s10570-010-9436-4 · Cited by 372
“The DP values of the nanofibers were larger than for microcrystalline cellulose extracted from Avicell (DP = 100) ( Mormann and Michel 2002 ).”
BackgroundInfluentialAulin, C., Ahola, S., Josefsson, P., Nishino, T., Hirose, Y., Österberg, M., & Wågberg, L. (2009) · Langmuir · doi:10.1021/la900323n · Cited by 363
Self-citationUltra porous nanocellulose aerogels as separation medium for mixtures of oil/water liquids
Cervin, N. T., Aulin, C., Larsson, P. T., & Wågberg, L. (2012) · Cellulose · doi:10.1007/s10570-011-9629-5 · Cited by 363
Self-citationChinga-Carrasco, G. (2011) · Nanoscale Research Letters · doi:10.1186/1556-276x-6-417 · Cited by 359
“pre-treating the cellulose fibres enzymatically [31] or chemically [32,33].”
MethodCellulose nanofibers produced from banana peel by chemical and enzymatic treatment
Tibolla, H., Pelissari, F. M., & Menegalli, F. C. (2014) · LWT - Food Science and Technology · doi:10.1016/j.lwt.2014.04.011 · Cited by 358
Cellulose Nanofiber Orientation in Nanopaper and Nanocomposites by Cold Drawing
Sehaqui, H., Ezekiel Mushi, N., Morimune, S., Salajkova, M., Nishino, T., & Berglund, L. A. (2012) · ACS Applied Materials & Interfaces · doi:10.1021/am2016766 · Cited by 351
Cellulose: Structure and Properties
Heinze, T. (2015) · Advances in Polymer Science · doi:10.1007/12_2015_319 · Cited by 300
“10) [48].”
BackgroundInfluentialTaipale, T., Österberg, M., Nykänen, A., Ruokolainen, J., & Laine, J. (2010) · Cellulose · doi:10.1007/s10570-010-9431-9 · Cited by 348
Self-citationSvagan, A. J., Samir, M. A. S. A., & Berglund, L. A. (2008) · Advanced Materials · doi:10.1002/adma.200701215 · Cited by 347
Self-aligned integration of native cellulose nanofibrils towards producing diverse bulk materials
Saito, T., Uematsu, T., Kimura, S., Enomae, T., & Isogai, A. (2011) · Soft Matter · doi:10.1039/c1sm06050c · Cited by 344
Industrial and crop wastes: A new source for nanocellulose biorefinery
García, A., Gandini, A., Labidi, J., Belgacem, N., & Bras, J. (2016) · Industrial Crops and Products · doi:10.1016/j.indcrop.2016.06.004 · Cited by 334
A Fast Method to Produce Strong NFC Films as a Platform for Barrier and Functional Materials
Österberg, M., Vartiainen, J., Lucenius, J., Hippi, U., Seppälä, J., Serimaa, R., & Laine, J. (2013) · ACS Applied Materials & Interfaces · doi:10.1021/am401046x · Cited by 336
Self-citationStructure and Mechanical Properties of Wet-Spun Fibers Made from Natural Cellulose Nanofibers
Iwamoto, S., Isogai, A., & Iwata, T. (2011) · Biomacromolecules · doi:10.1021/bm101510r · Cited by 337
da Silva, A. S., Espinheira, R. P., Teixeira, R. S. S., de Souza, M. F., Ferreira-Leitão, V., & Bon, E. P. S. (2020) · Biotechnology for Biofuels · doi:10.1186/s13068-020-01697-w · Cited by 322
Stelte, W., & Sanadi, A. R. (2009) · Industrial & Engineering Chemistry Research · doi:10.1021/ie9011672 · Cited by 331
Liimatainen, H., Visanko, M., Sirviö, J. A., Hormi, O. E. O., & Niinimaki, J. (2012) · Biomacromolecules · doi:10.1021/bm300319m · Cited by 329
Metadata
- Authors
- Pääkkö, M., Ankerfors, M., Kosonen, H., Nykänen, A., Ahola, S., Österberg, M., Ruokolainen, J., Laine, J., Larsson, P. T., Ikkala, O., & Lindström, T.
- Affiliations
- Trinity College Dublin (IE)
- Corresponding author
- Ikkala, O.
- Lindström, T.
- Venue
- Biomacromolecules
- Publisher
- American Chemical Society (ACS)
- Published
- 2007-05-03
- Volume
- 8
- Issue
- 6
- Pages
- 1934-1941
- ISSN
- 1525-7797 (ISSN-L)
- 1526-4602
- OpenAlex
- W2001245625
- Cited by
- 1,962
- References
- 23
- Citations by year
- 2026: 54 · 2025: 65 · 2024: 65 · 2023: 99 · 2022: 130 · 2021: 127 · 2020: 164 · 2019: 145 · 2018: 144 · 2017: 178 · 2016: 126 · 2015: 146 · 2014: 133 · 2013: 105 · 2012: 93
- FWCI
- 17.59
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Biomacromolecules (publishedVersion)
- PubMed (publishedVersion)
- Funders
- VINNOVA
- Topics
- Physical Sciences › Materials Science › Biomaterials › Advanced Cellulose Research Studies
- Life Sciences › Agricultural and Biological Sciences › Food Science › Polysaccharides Composition and Applications
- Life Sciences › Agricultural and Biological Sciences › Plant Science › Polysaccharides and Plant Cell Walls
- Keywords
- microfibrillated cellulose, enzymatic hydrolysis, mechanical shearing, high-pressure homogenization, cellulose fibrillation, cellulose gels, storage modulus, cellulose reinforcement
- MeSH terms
- Cellulose, Gels, Hydrogen-Ion Concentration, Hydrolysis, Magnetic Resonance Spectroscopy, Rheology, Stress, Mechanical, Temperature, Viscosity, Wood, Microscopy, Atomic Force, Cryoelectron Microscopy, Microscopy, Electron, Transmission, Macromolecular Substances, Nanoparticles
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.