Reducing the Cost of CO 2 Capture from Flue Gases Using Pressure Swing Adsorption
The DOI matches its Crossref record; 29 of the 31 references it cites were found in a registry or an index.
Abstract
Pressure swing adsorption (PSA) processes have been used extensively for gas separation, especially in the separation of hydrogen from CO 2, and in air purification. The objective of this paper is to examine the economic feasibility of pressure swing adsorption (PSA) for recovering CO 2 from postcombustion power plant flue gas. The analysis considers both high-pressure feed and vacuum desorption using commercial adsorbent 13X, which has a working capacity of 2.2 mol/kg and CO 2 /N 2 selectivity of 54. The results show that using vacuum desorption reduces the capture cost from US$57 to US$51 per ton of CO 2 avoided and is comparable in cost to CO 2 capture using conventional MEA absorption of US$49 per ton of CO 2 avoided. In this paper, a sensitivity analysis is also presented showing the effect on the capture cost with changes in process cycle; feed pressure and evacuation pressure; improvements the adsorbent characteristics; and selectivity and working capacity. The results show that a hypothetical adsorbent with a working capacity of 4.3 mol/kg and a CO 2 /N 2 selectivity of 150 can reduce the capture cost to US$30 per ton of CO 2 avoided.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“PSA process due to the simplicity as well as lower required energy is the most preferred one [52]”
From Biomass/Biochar carbon materials for CO2 capture and sequestration by cyclic adsorption processes: A review and prospects for future directions (2022) · cites this paper as [52]
Citations
Cites
Separation of CO2 from Flue Gas: A Review
Aaron, D., & Tsouris, C. (2005) · Separation Science and Technology · doi:10.1081/ss-200042244 · Cited by 1,525
(1995) · Filtration & Separation · doi:10.1016/s0015-1882(97)84188-2 · Cited by 1,169
Gas Separation by Adsorption Processes
Yang, R. (1988) · Chemical Engineering Science · doi:10.1016/0009-2509(88)80096-4 · Cited by 665
Chue, K. T., Kim, J. N., Yoo, Y. J., Cho, S. H., & Yang, R. T. (1995) · Industrial & Engineering Chemistry Research · doi:10.1021/ie00041a020 · Cited by 499
Concentration and recovery of carbon dioxide from flue gas by pressure swing adsorption
Kikkinides, E. S., Yang, R. T., & Cho, S. H. (1993) · Industrial & Engineering Chemistry Research · doi:10.1021/ie00023a038 · Cited by 369
An experimental adsorbent screening study for CO2 removal from N2
Harlick, P. J. E., & Tezel, F. H. (2004) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2004.07.035 · Cited by 355
Zhang, J., Webley, P. A., & Xiao, P. (2008) · Energy Conversion and Management · doi:10.1016/j.enconman.2007.06.007 · Cited by 298
Optimization of a Pressure-Swing Adsorption Process Using Zeolite 13X for CO2 Sequestration
Ko, D., Siriwardane, R., & Biegler, L. T. (2003) · Industrial & Engineering Chemistry Research · doi:10.1021/ie0204540 · Cited by 257
Reducing the Cost of CO2 Capture from Flue Gases Using Membrane Technology
Ho, M. T., Allinson, G. W., & Wiley, D. E. (2008) · Industrial & Engineering Chemistry Research · doi:10.1021/ie070541y · Cited by 256
Self-citationKinetic separation of methane—carbon dioxide mixture by adsorption on molecular sieve carbon
Kapoor, A., & Yang, R. T. (1989) · Chemical Engineering Science · doi:10.1016/0009-2509(89)80014-4 · Cited by 237
Research works printed but not linked: 7
- Reiner P., 1994, Carbon Dioxide Capture from Fossil Fuel Power Plants
- Ruthven D. M., 1984, Principles of Adsorption Processes
- Chou C., 2003, J. Chin. Inst. Chem. Eng., 34, 135
- Dave N. G., 2000, ACARP Report C7051
- Siriwardane, R.; Shen, M. S.; Fisher, E. P.; Poston, J. A.Adsorption and Desorption of CO 2 on Solid Sorbents. In Proceedings of the First Conference on Carbon Sequestration,Washington, DC, 2001.
- Chapel, D.; Mariz, C.; Ernest, J.Recovery of CO 2 from Flue Gases: Commercial Trend.Proceedings of Canadian Society of Chemical Engineers Annual Meeting, Saskatoon,Canada, 1999.
- Allinson, G.; Ho, M. T.; Neal, P. N.; Wiley, D. E.The Methodology used for Estimating the Costs of CCS.Proceedings of the Eighth International Conference on Greenhouse Gas Technologies (GHGT-8),Trondheim, Norway, 2006.
Cited by
Items 401–500 of 566
Adsorption Performance Indicator to Screen Carbon Adsorbents for Post-combustion CO2 Capture
Álvarez-Gutiérrez, N., Rubiera, F., Pevida, C., Jin, Y., Bae, J., & Su, S. (2017) · Energy Procedia · doi:10.1016/j.egypro.2017.03.1382 · Cited by 14
CO2 capture by adsorption: Research progress and technology demonstration
Pini, R., Petit, C., Danaci, D., Haghpanah, R., Luberti, M., Ribeiro, A. M., Subraveti, S. G., & Ward, A. (2026) · International journal of greenhouse gas control · doi:10.1016/j.ijggc.2026.104652 · Cited by 16
Anh, L. K., & Long, N. Q. (2024) · International Journal of Environmental Science and Technology · doi:10.1007/s13762-024-05667-9 · Cited by 14
“…has still been the most mature method (Rochelle 2009), adsorption can be more attractive because of simplicity in operation, lower energy needed for generation of CO 2 capture materials and producing no liquid waste like absorption solvents (Harrison 2005; Ho et al. 2008; Samanta et al. 2012).”
Nonlinear observer with adaptive grid allocation for a fixed-bed adsorption process
Won, W., & Lee, K. S. (2012) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2012.07.001 · Cited by 13
CO2 Capture Using Solid Sorbents
Shi, Y., Liu, Q., & He, Y. (2015) · Springer eBooks · doi:10.1007/978-1-4614-6431-0_83-1 · Cited by 18
One-Step Synthesis of an Ionic Covalent Organic Polymer for CO 2 Capture
Mohamed, S. I. G. P., Nguyen, T. D., Bavarian, M., & Nejati, S. (2022) · ACS Applied Polymer Materials · doi:10.1021/acsapm.2c01436 · Cited by 13
Yao, J., Ran, J., Srinivasakannan, C., Li, T., Li, Y., Li, S., Yin, S., & Zhang, L. (2022) · Chemical Engineering Journal · doi:10.1016/j.cej.2022.140620 · Cited by 13
Barua, A., Mehra, P., & Paul, A. (2023) · Results in Chemistry · doi:10.1016/j.rechem.2023.100807 · Cited by 16
Lu, J., Cao, H., & Li, J. (2020) · Energy · doi:10.1016/j.energy.2020.117604 · Cited by 13
CO2 capture from PCC power plants using solid sorbents: Bench scale study on synthetic gas
Ruiz, E., Sánchez, J. M., Maroño, M., & Otero, J. (2012) · Fuel · doi:10.1016/j.fuel.2012.06.111 · Cited by 13
Zid, S., Alcouffe, P., Zinet, M., & Espuche, É. (2022) · Polymers · doi:10.3390/polym14173489 · Cited by 12
Barla, R. J., Raghuvanshi, S., & Gupta, S. (2024) · Environmental Science and Pollution Research · doi:10.1007/s11356-024-33407-6 · Cited by 12
“…such as glycol, methanol, and dimethyl ether are used for flue gas separation because they are less corrosive and require less energy for regeneration; however, they have a lower capacity for different compound absorption and are temperature dependent (Ho et al. 2008; Songolzadeh et al. 2014).”
Ahmad, A. L., Zainuddin, M. I. F., Buddin, M. M. H. S., & Shafie, Z. M. H. M. (2022) · Arabian Journal for Science and Engineering · doi:10.1007/s13369-022-06698-5 · Cited by 12
“Pressure swing adsorption technology is among the well-known conventional methods used for CO2 removal from the flue gas in which requires a two-chamber for adsorption and desorption of the CO2 gas [4].”
MethodDeposition CO2 Capture Process Using a Free Piston Stirling Cooler
Song, C., Kitamura, Y., Li, S., & Lu, J. (2013) · Industrial & Engineering Chemistry Research · doi:10.1021/ie401026f · Cited by 12
Metal Organic Framework Mixed Matrix Membranes for CO2 Separation
Anastasiou, S., Bhoria, N., Pokhrel, J., & Karanikolos, G. N. (2016) · Abu Dhabi International Petroleum Exhibition & Conference (ADIPEC) · doi:10.2118/183264-ms · Cited by 12
Kim, S. H., Kim, J., Yeo, J.-G., & Yeo, Y. (2016) · Process Safety and Environmental Protection · doi:10.1016/j.cherd.2016.11.022 · Cited by 12
Vacuum pressure swing adsorption system for N2/CH4 separation under uncertainty
Han, Z., Xing, R. S., Zhang, D., Shen, Y., Fu, Q., Ding, Z., & Tian, C. (2018) · Process Safety and Environmental Protection · doi:10.1016/j.cherd.2018.12.017 · Cited by 12
CO2 Adsorption and Desorption for CO2 Enrichment at Low‐Concentrations Using Zeolite 13X
Bao, J., Zhao, J., & Bi, X. T. (2022) · Chemie Ingenieur Technik · doi:10.1002/cite.202200108 · Cited by 11
Supercapacitive swing adsorption of CO2: advances and future prospects
Khan, F. U., Bilal, M., Li, J., Xu, X., & Landskron, K. (2024) · Trends in Chemistry · doi:10.1016/j.trechm.2024.11.003 · Cited by 14
Nanoti, A., Dasgupta, S., Aarti, A., Biswas, N., Goswami, A. N., Garg, M. O., Divekar, S., & Pendem, C. (2012) · Industrial & Engineering Chemistry Research · doi:10.1021/ie300982d · Cited by 11
Panyarat, K., Surinwong, S., Prior, T. J., Konno, T., & Rujiwatra, A. (2017) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2017.06.003 · Cited by 11
Boer, D. G., Pour, Z. A., Langerak, J., Bakker, B., & Pescarmona, P. P. (2023) · Molecules · doi:10.3390/molecules28052198 · Cited by 12
“Among these, adsorption using solid sorbents is considered a very attractive separation technology because it is a straightforward process in which no liquid waste is generated [5,6].”
BackgroundCarbon Dioxide Adsorption by Metal Organic Frameworks (Synthesis, Testing and Modeling)
Sabouni, R. (2013) · Scholarship@Western (Western University) · Cited by 24
Dashti, H., & Lou, X. (2018) · The minerals, metals & materials series · doi:10.1007/978-3-319-72362-4_1 · Cited by 11
CO2 Capture Using Solid Sorbents
Shi, Y., Liu, Q., & He, Y. (2016) · Springer eBooks · doi:10.1007/978-3-319-14409-2_83 · Cited by 12
Ferreyra-Quiroz, M., Lira‐Barragán, L. F., El‐Halwagi, M. M., & Ponce‐Ortega, J. M. (2022) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.2c03880 · Cited by 10
He, C., Zhang, P., Ma, S., Zhang, Y., & Hu, T. (2023) · Dalton Transactions · doi:10.1039/d3dt01022h · Cited by 10
Natrella, G., Borgogna, A., Salladini, A., & Iaquaniello, G. (2021) · Cleaner Engineering and Technology · doi:10.1016/j.clet.2021.100280 · Cited by 14
A Structured Approach for Selecting Carbon Capture Process Models. A Case Study on Monoethanolamine
van der Spek, M. W., & Ramírez, A. (2014) · Energy Procedia · doi:10.1016/j.egypro.2014.11.137 · Cited by 10
Murakami, R., Shiota, K., Uchida, A., & Inagaki, F. (2024) · Green Chemistry · doi:10.1039/d4gc00736k · Cited by 13
Chaggar, P. K., Javan, K., Duarte, M. C., Darestani, M. T., & Markhali, B. P. (2025) · Environmental Science and Pollution Research · doi:10.1007/s11356-025-37222-5 · Cited by 13
“For H 2 -rich gas streams, higher pressure is required for separation of CO 2 (Ho et al. 2008).”
Danish, M., Parthasarthy, V., & Mesfer, M. K. A. (2021) · Carbon letters · doi:10.1007/s42823-021-00249-y · Cited by 9
Recent advances in software tools for adsorption science and engineering
Ga, S., & Chung, Y. G. (2022) · Molecular Systems Design & Engineering · doi:10.1039/d2me00036a · Cited by 10
Zhang, P., Ma, S., Zhang, Y., He, C., & Hu, T. (2024) · Dalton Transactions · doi:10.1039/d3dt03993e · Cited by 9
Effect of solvent on the CO 2 capture ability of polyester: A comparative study
Zulfiqar, S., & Sarwar, M. I. (2014) · Journal of Industrial and Engineering Chemistry · doi:10.1016/j.jiec.2014.06.008 · Cited by 9
Application of Polymeric Membrane in CO2 Capture from Post Combustion
Wang, S., & Han, X. (2012) · Advances in Chemical Engineering and Science · doi:10.4236/aces.2012.23039 · Cited by 9
“To improve membrane’s performance, pressure, vacuum and dual/multi stages of membrane are exerted or simulated to reach the competitive performance and minimum cost of CO2 capture [7,9-17].”
BackgroundResultГолых, Р. Н. (2017) · Journal of Applied Fluid Mechanics · doi:10.18869/acadpub.jafm.73.242.26605 · Cited by 9
“Thus, today, it is the most promising division sorption methods (Ho et al. 2008; Laugier et al. 2008; Scholes et al. 2013).”
BackgroundMetal organic frameworks-based mixed matrix membranes for gas separation
Khan, A. L., Habib, N., & Aslam, M. (2020) · Elsevier eBooks · doi:10.1016/b978-0-12-818821-7.00014-2 · Cited by 9
Hauchhum, L., Mahanta, P., & Wilde, J. D. (2015) · Transport in Porous Media · doi:10.1007/s11242-015-0569-7 · Cited by 12
Kim, H., Lee, J., Lee, S., Han, J., & Lee, I. (2015) · Korean Chemical Engineering Research · doi:10.9713/kcer.2015.53.1.31 · Cited by 9
Ferrarra, G., Ho, M. T., Lanzini, A., Leone, P., & Wiley, D. E. (2017) · Energy Procedia · doi:10.1016/j.egypro.2017.03.1782 · Cited by 9
Self-citationScibioh, M. A., & Viswanathan, B. (2018) · Elsevier eBooks · doi:10.1016/b978-0-444-63996-7.00003-1 · Cited by 11
Post‐Combustion Carbon Capture
Fan, X. (2015) · Wiley eBooks · doi:10.1002/9781118991978.hces024 · Cited by 9
A Guideline for Cross-Sector Coupling of Carbon Capture Technologies
Asgharian, H., Yahyaee, A., Yin, C., Liso, V., Nielsen, M. P., & Iov, F. (2024) · Gases · doi:10.3390/gases4040021 · Cited by 9
Wang, S., Wang, S., & Zhuo, Y. (2025) · Adsorption Science & Technology · doi:10.1177/02636174251385608 · Cited by 8
“Coal-fi red power plant fl ue gas has typically the characteristics of moderate temperature (50 – 60 °C), huge fl ow rate (about 500 m 3 /s for a 600 MW unit), low CO 2 content (10 – 15 vol.%), and humidi fi ed (6 – 10 vol.% moisture) (Ho et al., 2008; Sayari et al., 2011; Siegelman et al., 2021).”
Seo, Y., Park, S., Lee, G., Park, J., Oh, H., & Lee, E. (2025) · Bulletin of the Korean Chemical Society · doi:10.1002/bkcs.70077 · Cited by 8
Kakiuchi, T., Yajima, T., Shigaki, N., & Kawajiri, Y. (2022) · Adsorption · doi:10.1007/s10450-022-00371-x · Cited by 8
“reported that by introducing the pressure equalization step, the purity of the recovered gas is around 90%, which is almost 50% higher than classical PSA [25].”
BackgroundPorous sulfur-doped titanate as the support of tetraethylenepentamine for CO2 capture
Song, F., Zhong, Q., Chen, Q., Rong, X., & Wang, B. (2014) · Journal of CO2 Utilization · doi:10.1016/j.jcou.2014.11.005 · Cited by 8
Du, W., & Alkebsi, K. (2017) · International Symposium on Advanced Control of Industrial Processes · doi:10.1109/adconip.2017.7983816 · Cited by 8
“exist that can also be used to eradicate CO2 from different type of industrial outflows such as adsorption, cryogenic separations, absorption membranes etc [3-6].”
BackgroundPromoting further discussion of methanol and ammonia energy storage ecosystems
Boretti, A. A. (2023) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2023.10.251 · Cited by 9
Kan, X., Wang, J., & Dong, Y. (2024) · Chemical Communications · doi:10.1039/d4cc04439h · Cited by 7
Design and optimization of VSA process for post combustion carbon capture using NbOFFiVE-1-Ni
Wang, Q., Yang, W., Min, X., Wang, G., Wang, G., Zhao, B., Wang, L., & Sun, T. (2025) · Fuel · doi:10.1016/j.fuel.2025.135259 · Cited by 6
Advances in CO2 capture and conversion: the role of adsorbent materials
Li, W., Cui, H., Cai, W., Wen, N., Zhang, G., & Xu, Z. (2025) · Fuel · doi:10.1016/j.fuel.2025.136962 · Cited by 17
Wibowo, H., Ketwong, T., Cholwatthanatanakorn, N., Ding, L., & Areeprasert, C. (2024) · Waste Management · doi:10.1016/j.wasman.2024.01.029 · Cited by 9
Simulations of model metal-organic frameworks for the separation of carbon dioxide
Wells, B. A., Webley, P. A., & Chaffee, A. L. (2011) · Energy Procedia · doi:10.1016/j.egypro.2011.01.090 · Cited by 7
Song, Q.-Q., Jiang, Q., & Song, Z. (2015) · Petroleum Science · doi:10.1007/s12182-014-0001-x · Cited by 7
“(Ho et al. 2008; Martunus et al. 2012).”
Polyanionic cyano-fullerides for CO 2 capture: a DFT prediction
Anila, S., & Suresh, C. H. (2022) · Physical Chemistry Chemical Physics · doi:10.1039/d2cp03464f · Cited by 8
Binderless SAPO-34 beads for selective CO2 adsorption
Boer, D. G., Čiliak, D., Langerak, J., Bakker, B., & Pescarmona, P. P. (2023) · Sustainable Chemistry for Climate Action · doi:10.1016/j.scca.2023.100026 · Cited by 12
Current Status of Chemical Energy Storage Technologies
Jonathan, D., Dolci, F., Dominika, K., Rafael, O. C., & Eveline, W. R. (2020) · Joint Research Centre (European Commission) · doi:10.2760/280873 · Cited by 22
Rattanaya, T., Manmeen, A., Kongjan, P., Bunyakan, C., Reungsang, A., Prasertsit, K., Lombardi, L., & Jariyaboon, R. (2021) · Journal of Water Process Engineering · doi:10.1016/j.jwpe.2021.102405 · Cited by 7
Preparation of carbon molecular sieves and its impregnation with Co and Ni for CO2/N2 separation
Hemmat, M., Kelishami, A. R., & Vakili, M. H. (2017) · International Journal of Environmental Science and Technology · doi:10.1007/s13762-017-1526-5 · Cited by 7
“Porous solids offer an alternative method for CO2 separation from CO2/N2 mixture (Yang 1987;Kikkinides et al. 1993;Ruthven et al. 1993; Sircar et al. 1996; Siriwardane et al. 2001; Na et al. 2002; Ho et al. 2008).”
MethodSamal, P. P., & Krishnamurty, S. (2024) · The Journal of Physical Chemistry C · doi:10.1021/acs.jpcc.4c05835 · Cited by 6
Do, H., Ko, Y., Cho, M., & Lee, C. (2025) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2025.146839 · Cited by 6
Boer, D. G., van de Bovenkamp, H. H., Langerak, J., Bakker, B., & Pescarmona, P. P. (2024) · Energy Advances · doi:10.1039/d4ya00007b · Cited by 7
Chang, L.-H., & Yu, H.-Y. (2020) · Journal of the Taiwan Institute of Chemical Engineers · doi:10.1016/j.jtice.2020.12.019 · Cited by 6
A Comparative Study on CO2 Capture Efficiency Using Single and Blended Solvent
Hossain, M. S., Kumar, D., Azad, M. A. S., Azam, S. M. S., Amin, M. S. A., & Mozumder, M. S. I. (2023) · Process Integration and Optimization for Sustainability · doi:10.1007/s41660-023-00371-6 · Cited by 6
“It has a relatively high vapor pressure, causing high solvent carryover during the absorption and regeneration steps (Davy 2009; Ho et al. 2008).”
Kennedy, D. A., Carter, D., Wilson, S. M. W., Kruczek, B., & Tezel, F. H. (2017) · The Canadian Journal of Chemical Engineering · doi:10.1002/cjce.23095 · Cited by 7
Adsorption of Carbonyl Sulfide on Propylamine Tethered to Porous Silica
Bacsik, Z., & Hedin, N. (2018) · Langmuir · doi:10.1021/acs.langmuir.8b01371 · Cited by 6
Biogas Sweetening Technologies
Charisiou, N. D., Douvartzides, S. L., & Goula, M. A. (2021) · Wiley eBooks · doi:10.1002/9783527346523.ch7 · Cited by 6
Mammarella, D., Gallucci, K., & Giuliano, A. D. (2025) · ACS Omega · doi:10.1021/acsomega.5c00513 · Cited by 7
Hossain, M. R., Sun, Y., Ying, Y., Zheng, R., & Yan, M. (2025) · Waste Management & Research The Journal for a Sustainable Circular Economy · doi:10.1177/0734242x251361722 · Cited by 6
“All these make CO 2 accessible for mineralization processes, including using fly ash; these strategies assist in capturing or concentrating the CO 2 (Cousins et al., 2011; Ho et al., 2008).”
Continuous production of O2-free enriched CO2 from ambient air using moisture swing sorbents
Miyazaki, S., Yoshihara, M., Toyao, T., Maeno, Z., & Shimizu, K. (2023) · Next Nanotechnology · doi:10.1016/j.nxnano.2023.100029 · Cited by 4
Fluid flow analysis to describe the permeation process along the length of the porous tube
Najmi, H., El-Tabach, E., Gascoin, N., Chetehouna, K., Lamoot, L., & Falempin, F. H. (2017) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2017.08.132 · Cited by 6
Comparison of the most likely low-emission electricity production systems in Estonia
Baird, Z. S., Neshumayev, D., Järvik, O., & Powell, K. M. (2021) · PLoS ONE · doi:10.1371/journal.pone.0261780 · Cited by 4
Liu, X., Mingyang, Z., Chen, J., Hu, Z., Shuaifei, X., Mingxuan, T., & Zhang, C. (2022) · Green Sciences · doi:10.2478/pjct-2022-0018 · Cited by 5
CO2 hydrate slurry rheology, flow, and modeling: A comprehensive review
Bai, F., Chen, X., & Lu, Y. (2025) · Gas Science and Engineering · doi:10.1016/j.jgsce.2025.205748 · Cited by 4
Adsorption Mechanisms and AI‐Driven Discovery of Biomass‐Based CO 2 Sorbents
Hajiali, F., Chen, J., Zou, T., Renneckar, S. H., Gopaluni, R. B., Ellis, N., & Rojas, O. J. (2025) · Small · doi:10.1002/smll.202504877 · Cited by 7
Research on Pure Hydrogen Production Using a Fuel-Processing System Combined with a PSA System
Ko, S., & Lee, S.-Y. (2023) · Applied Sciences · doi:10.3390/app132111947 · Cited by 6
van Leeuwen, M. S., Plankensteiner, N., Maity, R., Gándara-Loe, J., Denayer, J. F. M., Ameloot, R., & Vereecken, P. M. (2024) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2024.113374 · Cited by 4
Kuchekar, S., Gaikwad, S., Kang, S. G., & Han, S. (2025) · Materials Chemistry and Physics · doi:10.1016/j.matchemphys.2025.131343 · Cited by 4
High Performance Membrane for Natural Gas Sweetening Plants
Khan, I. U., Othman, M. H. D., & Jilani, A. (2020) · Advances in Science, Technology & Innovation/Advances in science, technology & innovation · doi:10.1007/978-3-030-41295-1_5 · Cited by 5
Novel single-bed and twin-bed pressure swing adsorption systems
Thakur, R. S., Kaistha, N., & Rao, D. P. (2015) · Chemical Engineering and Processing - Process Intensification · doi:10.1016/j.cep.2015.06.003 · Cited by 4
Integrating carbon capture and storage with energy production from saline aquifers
Ganjdanesh, R. (2014) · Texas ScholarWorks (Texas Digital Library) · Cited by 4
Cai, J., Song, Y., Yu, Y., Chen, J., Wang, C., Ding, X., Yang, X., & Meng, J. (2025) · ACS Applied Polymer Materials · doi:10.1021/acsapm.5c01230 · Cited by 3
Mechanistic Insights Into Supercapacitive Swing Adsorption via Acid–Base Titrations
Khan, F. U., & Landskron, K. (2026) · Small · doi:10.1002/smll.73437 · Cited by 3
Wang, W. L., Zhang, Y. X., Liu, W., Wang, T., Fang, M. X., & Jiang, L. (2026) · Process Safety and Environmental Protection · doi:10.1016/j.cherd.2026.03.010 · Cited by 3
Optimization of Retrofit Decarbonization in Oil Refineries
Chattopadhyay, S., Gandhi, R., Grossmann, I. E., & Torres, A. I. (2024) · Systems and Control Transactions · doi:10.69997/sct.114841 · Cited by 3
Evaluating CO2 capture performance by adsorption using synthesized and commercial activated carbon
Danish, M., Parthasarthy, V., & Mesfer, M. K. A. (2021) · Separation Science and Technology · doi:10.1080/01496395.2021.1986070 · Cited by 3
Zhuo, S., Huang, Y., Hu, J., & Liu, H. (2010) · Frontiers of Chemical Science and Engineering · doi:10.1007/s11705-010-1007-6 · Cited by 3
Watabe, T., & Yogo, K. (2014) · Bulletin of the Chemical Society of Japan · doi:10.1246/bcsj.20130153 · Cited by 3
Khelifi, M. N., Saouli, O., Abdelouahed, L., Ledoux, A., Alam, M., Jeon, B., Ahn, H.-J., & Benguerba, Y. (2025) · Journal of CO2 Utilization · doi:10.1016/j.jcou.2025.103224 · Cited by 2
Xu, H., Bartling, S., Kondratenko, E. V., & Jentys, A. (2025) · ChemCatChem · doi:10.1002/cctc.202501297 · Cited by 2
Benchaabane, M.-E. A., Melouki, R., Bloch, E., Llewellyn, P. L., & Bourrelly, S. (2025) · Chemical Engineering Science · doi:10.1016/j.ces.2025.123181 · Cited by 2
Technology and policy options for achieving net zero steel manufacturing in the United States
Li, F. G. N., Bataille, C., Stiebert, S., Jafari, T., Balyk, O., & Glynn, J. D. M. (2026) · Energy Policy · doi:10.1016/j.enpol.2026.115124 · Cited by 2
Drünert, F., Rahmat, Y., Fleischmann, B., & Dietrich, R. (2026) · Glass Europe · doi:10.52825/glass-europe.v4i.2861 · Cited by 2
Sadeghalvad, B., Ebrahimi, H., & Azadmehr, A. (2022) · Elsevier eBooks · doi:10.1016/b978-0-323-89782-2.00012-0 · Cited by 5
Carbon Dioxide Capture in Metal-Organic Framework
Li, A., & Li, Y. (2022) · Highlights in Science Engineering and Technology · doi:10.54097/hset.v6i.955 · Cited by 2
Fu, D., Wang, Y., & Yu, S. (2023) · Minerals and Mineral Materials · doi:10.20517/mmm.2023.19 · Cited by 2
Parameter estimation and optimization of a PSA process for CO 2 capture
Won, W., Hwang, S., & Lee, K. S. (2011) · Cited by 2
CO2 and H2O Capture from High Humidity Flue Gas by Single Multi-Layer Vacuum Swing Adsorption Unit
Xu, D. Y., Guo, H. J., Liu, H. Q., Zhang, J., & Xiao, P. (2012) · Advanced materials research · doi:10.4028/www.scientific.net/amr.529.402 · Cited by 2
Metadata
- Authors
- Ho, M. T., Allinson, G. W., & Wiley, D. E.
- Affiliations
- UNSW Sydney (AU)
- Corresponding author
- Wiley, Dianne E.
- Venue
- Industrial & Engineering Chemistry Research
- Publisher
- American Chemical Society (ACS)
- Published
- 2008-06-17
- Volume
- 47
- Issue
- 14
- Pages
- 4883-4890
- ISSN
- 0888-5885 (ISSN-L)
- 1520-5045
- OpenAlex
- W2009040339
- Cited by
- 566
- References
- 31
- Citations by year
- 2026: 19 · 2025: 32 · 2024: 38 · 2023: 37 · 2022: 34 · 2021: 38 · 2020: 33 · 2019: 28 · 2018: 34 · 2017: 35 · 2016: 27 · 2015: 33 · 2014: 39 · 2013: 40 · 2012: 36
- FWCI
- 44.59
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Industrial & Engineering Chemistry Research (publishedVersion)
- Funders
- University of New South Wales
- Topics
- Physical Sciences › Chemical Engineering › Filtration and Separation › Carbon Dioxide Capture Technologies
- Physical Sciences › Environmental Science › Environmental Engineering › Industrial Gas Emission Control
- Physical Sciences › Environmental Science › Environmental Engineering › CO2 Sequestration and Geologic Interactions
- Keywords
- pressure swing adsorption, CO2 capture, post-combustion flue gas, vacuum desorption, zeolite 13X, capture cost, CO2/N2 selectivity, power plant emissions, sensitivity analysis
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.