Reducing the Cost of CO 2 Capture from Flue Gases Using Pressure Swing Adsorption
The DOI matches its Crossref record; 29 of the 31 references it cites were found in a registry or an index.
Abstract
Pressure swing adsorption (PSA) processes have been used extensively for gas separation, especially in the separation of hydrogen from CO 2, and in air purification. The objective of this paper is to examine the economic feasibility of pressure swing adsorption (PSA) for recovering CO 2 from postcombustion power plant flue gas. The analysis considers both high-pressure feed and vacuum desorption using commercial adsorbent 13X, which has a working capacity of 2.2 mol/kg and CO 2 /N 2 selectivity of 54. The results show that using vacuum desorption reduces the capture cost from US$57 to US$51 per ton of CO 2 avoided and is comparable in cost to CO 2 capture using conventional MEA absorption of US$49 per ton of CO 2 avoided. In this paper, a sensitivity analysis is also presented showing the effect on the capture cost with changes in process cycle; feed pressure and evacuation pressure; improvements the adsorbent characteristics; and selectivity and working capacity. The results show that a hypothetical adsorbent with a working capacity of 4.3 mol/kg and a CO 2 /N 2 selectivity of 150 can reduce the capture cost to US$30 per ton of CO 2 avoided.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“PSA process due to the simplicity as well as lower required energy is the most preferred one [52]”
From Biomass/Biochar carbon materials for CO2 capture and sequestration by cyclic adsorption processes: A review and prospects for future directions (2022) · cites this paper as [52]
Citations
Cites
Separation of CO2 from Flue Gas: A Review
Aaron, D., & Tsouris, C. (2005) · Separation Science and Technology · doi:10.1081/ss-200042244 · Cited by 1,525
(1995) · Filtration & Separation · doi:10.1016/s0015-1882(97)84188-2 · Cited by 1,169
Gas Separation by Adsorption Processes
Yang, R. (1988) · Chemical Engineering Science · doi:10.1016/0009-2509(88)80096-4 · Cited by 665
Chue, K. T., Kim, J. N., Yoo, Y. J., Cho, S. H., & Yang, R. T. (1995) · Industrial & Engineering Chemistry Research · doi:10.1021/ie00041a020 · Cited by 499
Concentration and recovery of carbon dioxide from flue gas by pressure swing adsorption
Kikkinides, E. S., Yang, R. T., & Cho, S. H. (1993) · Industrial & Engineering Chemistry Research · doi:10.1021/ie00023a038 · Cited by 369
An experimental adsorbent screening study for CO2 removal from N2
Harlick, P. J. E., & Tezel, F. H. (2004) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2004.07.035 · Cited by 355
Zhang, J., Webley, P. A., & Xiao, P. (2008) · Energy Conversion and Management · doi:10.1016/j.enconman.2007.06.007 · Cited by 298
Optimization of a Pressure-Swing Adsorption Process Using Zeolite 13X for CO2 Sequestration
Ko, D., Siriwardane, R., & Biegler, L. T. (2003) · Industrial & Engineering Chemistry Research · doi:10.1021/ie0204540 · Cited by 257
Reducing the Cost of CO2 Capture from Flue Gases Using Membrane Technology
Ho, M. T., Allinson, G. W., & Wiley, D. E. (2008) · Industrial & Engineering Chemistry Research · doi:10.1021/ie070541y · Cited by 256
Self-citationKinetic separation of methane—carbon dioxide mixture by adsorption on molecular sieve carbon
Kapoor, A., & Yang, R. T. (1989) · Chemical Engineering Science · doi:10.1016/0009-2509(89)80014-4 · Cited by 237
Research works printed but not linked: 7
- Reiner P., 1994, Carbon Dioxide Capture from Fossil Fuel Power Plants
- Ruthven D. M., 1984, Principles of Adsorption Processes
- Chou C., 2003, J. Chin. Inst. Chem. Eng., 34, 135
- Dave N. G., 2000, ACARP Report C7051
- Siriwardane, R.; Shen, M. S.; Fisher, E. P.; Poston, J. A.Adsorption and Desorption of CO 2 on Solid Sorbents. In Proceedings of the First Conference on Carbon Sequestration,Washington, DC, 2001.
- Chapel, D.; Mariz, C.; Ernest, J.Recovery of CO 2 from Flue Gases: Commercial Trend.Proceedings of Canadian Society of Chemical Engineers Annual Meeting, Saskatoon,Canada, 1999.
- Allinson, G.; Ho, M. T.; Neal, P. N.; Wiley, D. E.The Methodology used for Estimating the Costs of CCS.Proceedings of the Eighth International Conference on Greenhouse Gas Technologies (GHGT-8),Trondheim, Norway, 2006.
Cited by
Items 301–400 of 566
Chen, X., Wang, J., Ren, T., Li, Z., Du, T., Lu, X., Liu, L., Wang, Y., Xu, D. Y., Chang, C., et al. (2022) · Separation and Purification Technology · doi:10.1016/j.seppur.2022.122837 · Cited by 36
Rigdon, W. A., Omasta, T. J., Lewis, C. A., Hickner, M. A., Varcoe, J. R., Renner, J., Ayers, K. E., & Mustain, W. E. (2016) · Journal of Electrochemical Energy Conversion and Storage · doi:10.1115/1.4033411 · Cited by 36
Zhan, G., Bai, L., Wu, B., Cao, F., Duan, Y., Chang, F., Shang, D., Bai, Y., Li, Z., Zhang, X., et al. (2021) · Chemical Engineering Journal · doi:10.1016/j.cej.2021.129104 · Cited by 35
Enhanced mass transfer on hierarchical porous pure silica zeolite used for gas separation
Yang, J., Yuan, N., Xu, M., Liu, J., Li, J., & Deng, S. (2018) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2018.02.030 · Cited by 35
Keawkumay, C., Krukkratoke, P., Youngjan, S., Osakoo, N., Deekamwong, K., Khemthong, P., Phanthasri, J., Prayoonpokarach, S., & Wittayakun, J. (2024) · RSC Advances · doi:10.1039/d4ra02207f · Cited by 39
Xu, X., Dong, J., Xiao, X., Zhao, X., & Zhang, Q. (2021) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.0c08779 · Cited by 34
Pre-combustion CO2 capture by transition metal ions embedded in phthalocyanine sheets
Lü, K., Zhou, J., Zhou, L., Chen, X. S., Chan, S. H., & Sun, Q. (2012) · The Journal of Chemical Physics · doi:10.1063/1.4729471 · Cited by 34
Evaluation of the cyclic capacity of low-cost carbon adsorbents for post-combustion CO2 capture
Plaza, M. G., Pevida, C., Pis, J. J., & Rubiera, F. (2011) · Energy Procedia · doi:10.1016/j.egypro.2011.01.178 · Cited by 33
“Adsorption is a well developed separation technology with potential to reduce the cost of post-combustion capture compared to amine scrubbing [1-5].”
BackgroundGuido, G. D. (2023) · Process Safety and Environmental Protection · doi:10.1016/j.cherd.2023.10.011 · Cited by 33
Techno-economic assessment of industrial CO2 storage in depleted shale gas reservoirs
Tayari, F., Blumsack, S., Dilmore, R. M., & Mohaghegh, S. D. (2015) · Journal of Unconventional Oil and Gas Resources · doi:10.1016/j.juogr.2015.05.001 · Cited by 33
“…et al. (2001) 33–72 PC/FGD 21–62 IGCC Holloway (2008) 18–72 Power plant Finkenrath (2011) 43–62 Not specified Heddle et al. (2003) 14.55 Not specified Ho et al. (2008) 57 Not specified Rubin (2005) 29–44 PCa 11–32 IGCCb 28–57 NGCCc a Pulverized coal combustion. b Coal-based Integrated…”
BackgroundInfluentialGolmakani, A., Fatemi, S., & Tamnanloo, J. (2015) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.5b02690 · Cited by 33
Hajari, A., Atanga, M. A., Hartvigsen, J., Rownaghi, A. A., & Rezaei, F. (2017) · Energy & Fuels · doi:10.1021/acs.energyfuels.6b02881 · Cited by 33
Food wastes derived adsorbents for carbon dioxide and benzene gas sorption
Opatokun, S. A., Prabhu, A., Shoaibi, A. A., Srinivasakannan, C., & Strezov, V. (2016) · Chemosphere · doi:10.1016/j.chemosphere.2016.10.083 · Cited by 35
Design of a Pressure Swing Adsorption Process for Postcombustion CO2 Capture
Pirngruber, G. D., & Leinekugel‐le‐Cocq, D. (2013) · Industrial & Engineering Chemistry Research · doi:10.1021/ie400015a · Cited by 33
Bahamon, D., Ogungbenro, A. E., Khaleel, M., Abu-Zahra, M. R. M., & Vega, L. F. (2020) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.9b05542 · Cited by 31
2.5-dimensional covalent organic frameworks
Kitano, T., Goto, S., Wang, X., Kamihara, T., Sei, Y., Kondo, Y., Sannomiya, T., Uekusa, H., & Murakami, Y. (2025) · Nature Communications · doi:10.1038/s41467-024-55729-2 · Cited by 31
Development of zeolite adsorbent with low water sensitivity for CO2 capture
Hu, P., Oishi, R., Ya, H., Yonezawa, Y., Matsukura, M., Iyoki, K., Okubo, T., & Wakihara, T. (2025) · Chemical Engineering Journal · doi:10.1016/j.cej.2025.161054 · Cited by 36
Characteristics of oat hull based biosorbent for natural gas dehydration in a PSA process
Ghanbari, S., & Niu, C. H. (2019) · Journal of Natural Gas Science and Engineering · doi:10.1016/j.jngse.2018.11.014 · Cited by 29
An overview and outlook on gas adsorption: for the enrichment of low concentration coalbed methane
Liu, H., Ding, W. J., Zhou, F., Yang, G., & Du, Y. (2019) · Separation Science and Technology · doi:10.1080/01496395.2019.1585454 · Cited by 31
“Reproduced from Ho et al.([108]) with permission from American Chemical Society.”
MethodHayashi, E., Thomas, M. L., Hashimoto, K., Tsuzuki, S., Ito, A., & Watanabe, M. (2019) · ACS Applied Polymer Materials · doi:10.1021/acsapm.9b00383 · Cited by 30
Influence of regeneration conditions on cyclic CO2 adsorption on NaA zeolite at high pressures
de Oliveira, L. H., Pereira, M. V. A., Meneguin, J. G., de Barros, M. A. S. D., do Nascimento, J. F., & Arroyo, P. A. (2022) · Journal of CO2 Utilization · doi:10.1016/j.jcou.2022.102296 · Cited by 33
Liang, Z., Marshall, M., Ng, C. H., & Chaffee, A. L. (2013) · Energy & Fuels · doi:10.1021/ef402212t · Cited by 30
Siloxanes capture by ionic liquids: Solvent selection and process evaluation
Santiago, R., Moya, C., & Palomar, J. F. (2020) · Chemical Engineering Journal · doi:10.1016/j.cej.2020.126078 · Cited by 29
Girimonte, R., Testa, F., Turano, M., Leone, G., Gallo, M., & Golemme, G. (2022) · Processes · doi:10.3390/pr10020422 · Cited by 33
Santos, S. C. G., Pedrosa, A. M. G., Souza, M. J. B., Cecilia, J. A., & Rodríguez-Castellón, E. (2015) · Materials Research Bulletin · doi:10.1016/j.materresbull.2015.05.037 · Cited by 30
Ejector integration for the cost effective design of the SelexolTM process
Ashrafi, O., Bashiri, H., Esmaeili, A., Sapoundjiev, H., & Navarri, P. (2018) · Energy · doi:10.1016/j.energy.2018.08.053 · Cited by 28
Zentou, H., Aliyu, M., Abdalla, M. A., Abdelaziz, O. Y., Hoque, B., Alloush, A. M., Tayeb, I. M., Patchigolla, K., & Abdelnaby, M. M. (2024) · The Chemical Record · doi:10.1002/tcr.202400188 · Cited by 49
Madugula, A. C. S., Sachde, D., Hovorka, S., Meckel, T. A., & Benson, T. J. (2021) · Chemical Engineering Journal Advances · doi:10.1016/j.ceja.2021.100162 · Cited by 32
A study on natural clinoptilolite for CO 2 /N 2 gas separation
Karousos, D. S., Sapalidis, A. A., Kouvelos, E. P., Romanos, G. E., & Kanellopoulos, N. K. (2015) · Separation Science and Technology · doi:10.1080/01496395.2015.1085880 · Cited by 32
“Using commercial zeolite 13X total cost is 51$/ton CO2 and this is achieved solely by application of vacuum desorption (5).”
BackgroundMethodTechnology Evolution in Membrane-Based CCS
Míguez, J. L., Porteiro, J., Pérez-Orozco, R., & Gómez, M. A. (2018) · Energies · doi:10.3390/en11113153 · Cited by 30
“[104,105] analyzed pressure swing adsorption and membrane costs.”
BackgroundHan, Y., Meng, L., Liu, Y., Li, H., Li, H., Zhou, Y., Wu, M., & Han, Z. (2023) · Separation and Purification Technology · doi:10.1016/j.seppur.2023.123642 · Cited by 28
Evaluation of carbon dioxide–nitrogen separation through fixed bed measurements and simulations
Rios, R. B., Correia, L. S., Bastos-Neto, M., Torres, A. E. B., Hatimondi, S. A., Ribeiro, A. M., Rodrigues, A. E., Cavalcante, C. L., & Azevedo, D. C. S. (2014) · Adsorption · doi:10.1007/s10450-014-9639-3 · Cited by 30
“…the feasibility of using a Gemini -5 landfill gas CO2/CH4 PSA separation plant for CO2 capture from power plant flue gases, Zhang et al. (2008) and Ho et al. (2008) concluded that a vacuum swing cycle is economically preferred to a pressure swing cycle for CO2 capture from low pressure flue gas…”
BackgroundInfluentialRiboldi, L., Bolland, O., Ngoy, J. M., & Wagner, N. J. (2014) · Energy Procedia · doi:10.1016/j.egypro.2014.11.248 · Cited by 27
Huang, Q., & Eić, M. (2012) · Separation and Purification Technology · doi:10.1016/j.seppur.2012.10.040 · Cited by 27
Liu, X., Wang, W., Wang, M., & Wang, P. (2014) · Energy & Fuels · doi:10.1021/ef402272k · Cited by 27
He, C., Wang, Y., Chen, Y., Wang, X., Yang, J., Li, L., & Li, J. (2021) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2021.111096 · Cited by 26
Llano-Restrepo, M. (2010) · Fluid Phase Equilibria · doi:10.1016/j.fluid.2010.03.013 · Cited by 26
Dynamic properties in CO 2 adsorption on amine-modified MCM-41
Gao, F., Zhou, J., Bian, Z., Jing, C., Hu, J., & Liu, H. (2013) · Proceedings of the Institution of Mechanical Engineers Part E Journal of Process Mechanical Engineering · doi:10.1177/0954408912469491 · Cited by 27
“Equation (5) can be simplified as equation (6)”
BackgroundInfluentialCompetitive Adsorption of Moisture and SO2 for Carbon Dioxide Capture by Zeolites FAU 13X and LTA 5A
Yang, X., Wang, Q., Chen, J., Liu, H., Xu, L., & Rao, M. (2024) · Processes · doi:10.3390/pr12081547 · Cited by 30
Zhang, Z., Palakkal, A. S., Wu, X., Jiang, J., & Jiang, Z. (2025) · Environmental Science & Technology · doi:10.1021/acs.est.5c00768 · Cited by 25
Surface modification induced enhanced CO 2 sorption in cucurbit[6]uril, an organic porous material
Mohan, M., Suzuki, T., Nair, A. K., Pillai, S., Warrier, K. G. K., Hareesh, U. S., Nair, B. N., & Gale, J. D. (2017) · Physical Chemistry Chemical Physics · doi:10.1039/c7cp03866f · Cited by 25
Performance analysis of solar-assisted CO2 adsorption capture system based on dynamic simulation
Chen, B., Deng, S., Zhao, L., Li, S., Wu, K., Chen, L., Zhao, J., Yuan, X., & Liang, Y. (2020) · Solar Energy · doi:10.1016/j.solener.2020.09.017 · Cited by 25
Fischer, M., & Bell, R. G. (2013) · The Journal of Physical Chemistry C · doi:10.1021/jp405507y · Cited by 24
Development of nanoemulsion CO2 absorbents for mass transfer performance enhancement
Kim, S., Jeong, M., Lee, J. W., Kim, S. Y., Choi, C. K., & Kang, Y. T. (2018) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2018.03.012 · Cited by 25
Realpe, N., Lezcano, G., Kulkarni, S. R., Sayas, S., Morlanés, N., Rakib, M., Aldilaijan, R., Solami, B., Gascón, J., & Castaño, P. (2024) · Applied Energy · doi:10.1016/j.apenergy.2024.124244 · Cited by 23
Ganjdanesh, R., Pope, G. A., & Sepehrnoori, K. (2015) · International journal of greenhouse gas control · doi:10.1016/j.ijggc.2015.01.004 · Cited by 23
Geometry variation in porous covalent triazine polymer (CTP) for CO 2 adsorption
Lee, S.-P., Mellon, N. B., Shariff, A. M., & Lévêque, J. (2018) · New Journal of Chemistry · doi:10.1039/c8nj00638e · Cited by 23
Electrochemical flow systems enable renewable energy industrial chain of CO2 reduction
Hung, S. (2020) · Pure and Applied Chemistry · doi:10.1515/pac-2020-0705 · Cited by 23
Pishva, S., & Hassanajili, S. (2021) · Journal of Industrial and Engineering Chemistry · doi:10.1016/j.jiec.2021.11.046 · Cited by 24
Tara, N., Shamair, Z., Habib, N., Craven, M., Bilad, M. R., Usman, M., Tu, X., & Khan, A. L. (2021) · Process Safety and Environmental Protection · doi:10.1016/j.cherd.2021.12.007 · Cited by 23
Wu, W., Niu, H., Lai, S., Liu, C., Zhou, L., & Huang, X. (2022) · Polymer · doi:10.1016/j.polymer.2022.125273 · Cited by 23
In silico engineering of ion-exchanged zeolites for high-performance carbon capture in PSA processes
Deng, Z., Gopalan, A., & Sarkisov, L. (2023) · Chemical Engineering Journal · doi:10.1016/j.cej.2023.141597 · Cited by 25
Enhanced CO2 removal in hollow fiber membrane contactors using amine-based nanofluids
Gargari, S. F., & Mirfendereski, S. M. (2023) · Journal of Industrial and Engineering Chemistry · doi:10.1016/j.jiec.2023.07.070 · Cited by 23
Mu, W., Huang, X. L., Zhong, R., Xia, W., Liu, J., & Zou, R. (2015) · CrystEngComm · doi:10.1039/c4ce02073a · Cited by 23
Song, C., Kansha, Y., Ishizuka, M., Fu, Q., & Tsutsumi, A. (2015) · Chemical Engineering and Processing - Process Intensification · doi:10.1016/j.cep.2015.03.008 · Cited by 25
Won, W., & Lee, K. S. (2010) · Chemical Engineering Journal · doi:10.1016/j.cej.2010.10.067 · Cited by 23
Optimized Hollow Fiber Sorbents and Pressure Swing Adsorption Process for H 2 Recovery
Ohs, B., Lohaus, J., Marten, D., Hannemann, R., Krieger, A., & Weßling, M. (2018) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.7b05368 · Cited by 23
Santiago, R. G., Siqueira, R. M., Alves, C. A., Vilarrasa‐García, E., Maia, D. A. S., Bastos-Neto, M., & Azevedo, D. C. S. (2019) · Adsorption · doi:10.1007/s10450-019-00112-7 · Cited by 25
Wadi, B., Golmakani, A., Manovic, V. M., & Nabavi, S. A. (2021) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.1c02416 · Cited by 23
MOF adsorbents for flue gas separation: Comparison of material ranking approaches
Altıntaş, Ç., & Keskın, S. (2022) · Chemical Engineering Research and Design · doi:10.1016/j.cherd.2022.01.030 · Cited by 21
Flexible Operation Scheduling of a Power Plant Integrated with PCC Processes under Market Dynamics
Khalilpour, K. R. (2014) · Industrial & Engineering Chemistry Research · doi:10.1021/ie404225q · Cited by 22
Álvarez-Gutiérrez, N., Gil, M. V., Rubiera, F., & Pevida, C. (2018) · Journal of CO2 Utilization · doi:10.1016/j.jcou.2018.10.001 · Cited by 21
“The following assumptions are considered in the calculations [30,40]: 175”
BackgroundInfluentialHabibollahzade, A., Mehrabadi, Z. K., & Houshfar, E. (2021) · International Journal of Energy Research · doi:10.1002/er.6532 · Cited by 22
Kantor, I. D., Betancourt‐Torcat, A., Elkamel, A., Fowler, M. W., & Almansoori, A. S. (2015) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2015.03.017 · Cited by 29
Barelli, L., Bidini, G., Ottaviano, A., & Perla, M. (2020) · Journal of Energy Storage · doi:10.1016/j.est.2020.101471 · Cited by 21
Highly Selective Zeolite Topologies for Flue Gas Separation
Gómez‐Álvarez, P., & Calero, S. (2016) · Chemistry – A European Journal · doi:10.1002/chem.201604009 · Cited by 21
Carbon capture via electrochemically mediated alkaline absorption: Lab-scale continuous operation
Shi, M., Castaño, S. V., Shu, Q., Tedesco, M., Kuntke, P., Hamelers, H. V. M., & Fosbøl, P. L. (2024) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2024.143767 · Cited by 22
Biomass as a source of adsorbents for CO2 capture
Karimi, M., Rodrigues, A. E., & Silva, J. A. C. (2021) · Elsevier eBooks · doi:10.1016/b978-0-12-821601-9.00010-8 · Cited by 24
Temperature Effects in Flexible Adsorption Processes for Amorphous Microporous Polymers
Morgan, W. J., Anstine, D. M., & Colina, C. M. (2022) · The Journal of Physical Chemistry B · doi:10.1021/acs.jpcb.2c04543 · Cited by 21
Kwon, S., Fan, M., DaCosta, H. F. M., Russell, A. G., Berchtold, K. A., & Dubey, M. K. (2010) · Elsevier eBooks · doi:10.1016/b978-0-8155-2049-8.10010-5 · Cited by 26
Marks, S. D., Riascos-Rodríguez, K., Arrieta-Pérez, R. R., Yakovenko, A. A., Exley, J., Evans, P. G., & Hernández‐Maldonado, A. J. (2020) · Journal of Materials Chemistry A · doi:10.1039/d0ta03298k · Cited by 20
Tena, A., Marcos-Fernández, Á. A., Lozano, Á. E., de Abajo, J., Palacio, L., Prádanos, P., & Hernández, A. (2013) · Chemical Engineering Science · doi:10.1016/j.ces.2013.08.043 · Cited by 20
“A first instance analysis could lead to conclude that chemical adsorption processes are more interesting because they can give high purity at a relatively low price (Ho et al., 2008; Merkel et al., 2010; Oexmann et al., 2008; Qin et al., 2010).”
ZSM-5/Silicalite-1 core-shell beads as CO2 adsorbents with increased hydrophobicity
Boer, D. G., Pour, Z. A., Poli, S., Langerak, J., Bakker, B., & Pescarmona, P. P. (2023) · Materials Today Chemistry · doi:10.1016/j.mtchem.2023.101621 · Cited by 20
Minardi, E. R., Chakraborty, S., Calabrò, V., Curcio, S., & Drioli, E. (2014) · RSC Advances · doi:10.1039/c4ra11819g · Cited by 19
Aluminophosphate monoliths with high CO 2 -over-N 2 selectivity and CO 2 capture capacity
Akhtar, F., Keshavarzi, N., Shakarova, D., Cheung, O. Y. H., Hedin, N., & Bergström, L. (2014) · RSC Advances · doi:10.1039/c4ra05009f · Cited by 19
Liu, A., Lu, G., Fan, X., & Lau, C. H. (2023) · Journal of Materials Chemistry A · doi:10.1039/d3ta04553f · Cited by 18
A review of biogas upgrading technologies: key emphasis on electrochemical systems
Mohammadpour, H., Cheng, K. Y., Pivrikas, A., & Ho, G. (2024) · Water Science & Technology · doi:10.2166/wst.2024.394 · Cited by 19
Probing the potential of polyester for CO2 capture
Zulfiqar, S., & Sarwar, M. I. (2014) · Journal of Environmental Sciences · doi:10.1016/j.jes.2014.05.007 · Cited by 18
Materials challenges in carbon-mitigation technologies
Espinal, L., & Morreale, B. D. (2012) · MRS Bulletin · doi:10.1557/mrs.2012.10 · Cited by 21
Computational evaluation of aluminophosphate zeotypes for CO 2 /N 2 separation
Fischer, M. (2017) · Physical Chemistry Chemical Physics · doi:10.1039/c7cp03841k · Cited by 18
Bhoria, N., Pokhrel, J., Anastasiou, S., Reddy, K. S. K., Romanos, G. E., & Karanikolos, G. N. (2020) · Materials Today Proceedings · doi:10.1016/j.matpr.2020.07.466 · Cited by 18
Characterization of a high-performance biosorbent for natural gas dehydration
Ghanbari, S., & Niu, C. H. (2018) · Energy & Fuels · doi:10.1021/acs.energyfuels.8b02665 · Cited by 17
Rahimalimamaghani, A., Ramezani, R., Tanaka, D. A. P., & Gallucci, F. (2023) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.3c00719 · Cited by 17
Khalid, H. M., Mujahid, A., Ali, A., Khan, A. L., Saleem, M., & Santos, R. M. (2024) · International Journal of Energy Research · doi:10.1155/2024/2107340 · Cited by 17
Mathematical modeling of CO2 membrane absorption system using ionic liquid solutions
Darabi, M., & Pahlavanzadeh, H. (2019) · Chemical Engineering and Processing - Process Intensification · doi:10.1016/j.cep.2019.107743 · Cited by 17
Wu, X., & Jiang, J. (2024) · Chemical Science · doi:10.1039/d4sc05616g · Cited by 19
Tatsumichi, T., Okuno, R., Hashimoto, H., Namiki, N., & Maeno, Z. (2024) · Green Chemistry · doi:10.1039/d4gc03218g · Cited by 16
CO2 adsorption by swing technologies and challenges on industrialization
Fouladi, N., Makarem, M. A., Sedghamiz, M. A., & Rahimpour, H. R. (2020) · Elsevier eBooks · doi:10.1016/b978-0-12-819657-1.00011-6 · Cited by 18
Electrothermal Carbon Capture and Utilization─A Review
Patil, S. C., Fahim, S. T. M., Lee, J. H., & Gilliard‐AbdulAziz, K. L. (2024) · ACS Energy Letters · doi:10.1021/acsenergylett.4c02851 · Cited by 18
On the water stability of ionic liquids/Cu-BTC composites: an experimental study
Xia, X., Li, W. H., & Li, S. (2019) · Journal of Nanoparticle Research · doi:10.1007/s11051-019-4475-8 · Cited by 15
Kim, S., Kim, M., & Kim, J. (2019) · JOURNAL OF CHEMICAL ENGINEERING OF JAPAN · doi:10.1252/jcej.18we153 · Cited by 15
Wang, T., Yao, H., Song, N., Yang, Y., Shi, K., & Guan, S. (2020) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.9b06141 · Cited by 15
Thiruvenkatachari, R., Su, S., Yu, X. X., & Jin, Y. (2015) · International journal of greenhouse gas control · doi:10.1016/j.ijggc.2015.08.018 · Cited by 15
Fischer, M., & Bell, R. G. (2012) · Zeitschrift für Kristallographie - Crystalline Materials · doi:10.1524/zkri.2012.1562 · Cited by 15
Pahlavanzadeh, H., Darabi, M., Ghaleh, V. R., & Bakhtiari, O. (2020) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.0c02242 · Cited by 15
Maharana, A. K., Sarkar, S. K., Mukherjee, S., Sarkar, R., Rambabu, G., Sugamata, K., & Das, S. (2025) · Journal of Materials Chemistry A · doi:10.1039/d5ta01351h · Cited by 14
Chattopadhyay, S., Karthikeyan, K., Gandhi, R., Grossmann, I. E., & Torres, A. I. (2025) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.4c04995 · Cited by 14
Towards functionalized graphene/polymer monolithic structures for selective CO2 capture
Barbarin, I., Πολιτάκος, Ν., Serrano, L., Cecilia, J. A., Sánz, O., & Tomovská, R. (2022) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2022.111907 · Cited by 14
Reviewing the progress toward an ammonia energy storage ecosystem
Boretti, A. A. (2024) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2024.03.029 · Cited by 15
Ghougassian, P. G., Lopez, J. A. P., Manousiouthakis, V. I., & Smirniotis, P. G. (2014) · International journal of greenhouse gas control · doi:10.1016/j.ijggc.2013.12.004 · Cited by 14
Metadata
- Authors
- Ho, M. T., Allinson, G. W., & Wiley, D. E.
- Affiliations
- UNSW Sydney (AU)
- Corresponding author
- Wiley, Dianne E.
- Venue
- Industrial & Engineering Chemistry Research
- Publisher
- American Chemical Society (ACS)
- Published
- 2008-06-17
- Volume
- 47
- Issue
- 14
- Pages
- 4883-4890
- ISSN
- 0888-5885 (ISSN-L)
- 1520-5045
- OpenAlex
- W2009040339
- Cited by
- 566
- References
- 31
- Citations by year
- 2026: 19 · 2025: 32 · 2024: 38 · 2023: 37 · 2022: 34 · 2021: 38 · 2020: 33 · 2019: 28 · 2018: 34 · 2017: 35 · 2016: 27 · 2015: 33 · 2014: 39 · 2013: 40 · 2012: 36
- FWCI
- 44.59
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Industrial & Engineering Chemistry Research (publishedVersion)
- Funders
- University of New South Wales
- Topics
- Physical Sciences › Chemical Engineering › Filtration and Separation › Carbon Dioxide Capture Technologies
- Physical Sciences › Environmental Science › Environmental Engineering › Industrial Gas Emission Control
- Physical Sciences › Environmental Science › Environmental Engineering › CO2 Sequestration and Geologic Interactions
- Keywords
- pressure swing adsorption, CO2 capture, post-combustion flue gas, vacuum desorption, zeolite 13X, capture cost, CO2/N2 selectivity, power plant emissions, sensitivity analysis
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.