Reducing the Cost of CO 2 Capture from Flue Gases Using Pressure Swing Adsorption
The DOI matches its Crossref record; 29 of the 31 references it cites were found in a registry or an index.
Abstract
Pressure swing adsorption (PSA) processes have been used extensively for gas separation, especially in the separation of hydrogen from CO 2, and in air purification. The objective of this paper is to examine the economic feasibility of pressure swing adsorption (PSA) for recovering CO 2 from postcombustion power plant flue gas. The analysis considers both high-pressure feed and vacuum desorption using commercial adsorbent 13X, which has a working capacity of 2.2 mol/kg and CO 2 /N 2 selectivity of 54. The results show that using vacuum desorption reduces the capture cost from US$57 to US$51 per ton of CO 2 avoided and is comparable in cost to CO 2 capture using conventional MEA absorption of US$49 per ton of CO 2 avoided. In this paper, a sensitivity analysis is also presented showing the effect on the capture cost with changes in process cycle; feed pressure and evacuation pressure; improvements the adsorbent characteristics; and selectivity and working capacity. The results show that a hypothetical adsorbent with a working capacity of 4.3 mol/kg and a CO 2 /N 2 selectivity of 150 can reduce the capture cost to US$30 per ton of CO 2 avoided.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“PSA process due to the simplicity as well as lower required energy is the most preferred one [52]”
From Biomass/Biochar carbon materials for CO2 capture and sequestration by cyclic adsorption processes: A review and prospects for future directions (2022) · cites this paper as [52]
Citations
Cites
Separation of CO2 from Flue Gas: A Review
Aaron, D., & Tsouris, C. (2005) · Separation Science and Technology · doi:10.1081/ss-200042244 · Cited by 1,525
(1995) · Filtration & Separation · doi:10.1016/s0015-1882(97)84188-2 · Cited by 1,169
Gas Separation by Adsorption Processes
Yang, R. (1988) · Chemical Engineering Science · doi:10.1016/0009-2509(88)80096-4 · Cited by 665
Chue, K. T., Kim, J. N., Yoo, Y. J., Cho, S. H., & Yang, R. T. (1995) · Industrial & Engineering Chemistry Research · doi:10.1021/ie00041a020 · Cited by 499
Concentration and recovery of carbon dioxide from flue gas by pressure swing adsorption
Kikkinides, E. S., Yang, R. T., & Cho, S. H. (1993) · Industrial & Engineering Chemistry Research · doi:10.1021/ie00023a038 · Cited by 369
An experimental adsorbent screening study for CO2 removal from N2
Harlick, P. J. E., & Tezel, F. H. (2004) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2004.07.035 · Cited by 355
Zhang, J., Webley, P. A., & Xiao, P. (2008) · Energy Conversion and Management · doi:10.1016/j.enconman.2007.06.007 · Cited by 298
Optimization of a Pressure-Swing Adsorption Process Using Zeolite 13X for CO2 Sequestration
Ko, D., Siriwardane, R., & Biegler, L. T. (2003) · Industrial & Engineering Chemistry Research · doi:10.1021/ie0204540 · Cited by 257
Reducing the Cost of CO2 Capture from Flue Gases Using Membrane Technology
Ho, M. T., Allinson, G. W., & Wiley, D. E. (2008) · Industrial & Engineering Chemistry Research · doi:10.1021/ie070541y · Cited by 256
Self-citationKinetic separation of methane—carbon dioxide mixture by adsorption on molecular sieve carbon
Kapoor, A., & Yang, R. T. (1989) · Chemical Engineering Science · doi:10.1016/0009-2509(89)80014-4 · Cited by 237
Research works printed but not linked: 7
- Reiner P., 1994, Carbon Dioxide Capture from Fossil Fuel Power Plants
- Ruthven D. M., 1984, Principles of Adsorption Processes
- Chou C., 2003, J. Chin. Inst. Chem. Eng., 34, 135
- Dave N. G., 2000, ACARP Report C7051
- Siriwardane, R.; Shen, M. S.; Fisher, E. P.; Poston, J. A.Adsorption and Desorption of CO 2 on Solid Sorbents. In Proceedings of the First Conference on Carbon Sequestration,Washington, DC, 2001.
- Chapel, D.; Mariz, C.; Ernest, J.Recovery of CO 2 from Flue Gases: Commercial Trend.Proceedings of Canadian Society of Chemical Engineers Annual Meeting, Saskatoon,Canada, 1999.
- Allinson, G.; Ho, M. T.; Neal, P. N.; Wiley, D. E.The Methodology used for Estimating the Costs of CCS.Proceedings of the Eighth International Conference on Greenhouse Gas Technologies (GHGT-8),Trondheim, Norway, 2006.
Cited by
Items 201–300 of 566
Li, J., Hou, Y., Wang, P., & Yang, B. (2018) · Energies · doi:10.3390/en12010023 · Cited by 74
“[52] 2008 Reducing the cost of CO2 capture from flue gases using pressure swing adsorption 270”
Pressure swing adsorption properties of activated carbon for methanol, acetone and toluene
Zhou, C., Zhou, K. C., Li, H., Xu, X., Liu, B., Li, H., Zeng, Z., Ma, W., & Li, L. (2020) · Chemical Engineering Journal · doi:10.1016/j.cej.2020.127384 · Cited by 67
Sáenz-Cavazos, P. A., Hunter‐Sellars, E., Iacomi, P., McIntyre, S. R., Danaci, D., & Williams, D. R. (2023) · Frontiers in Energy Research · doi:10.3389/fenrg.2023.1167043 · Cited by 72
Akhtar, F., & Bergström, L. (2011) · Journal of the American Ceramic Society · doi:10.1111/j.1551-2916.2010.04044.x · Cited by 65
Mukhtar, A., Saqib, S., Mellon, N. B., Rafiq, S., Babar, M., Ullah, S., Muhammad, N., Khan, A. L., Ayoub, M., Ibrahim, M., et al. (2020) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2020.123999 · Cited by 63
He, C., Wang, Y., Chen, Y., Wang, X., Yang, J., Li, L., & Li, J. (2020) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.0c16575 · Cited by 63
Energy analysis of the cryogenic CO2 capture process based on Stirling coolers
Song, C., Kitamura, Y., & Li, S. (2013) · Energy · doi:10.1016/j.energy.2013.10.087 · Cited by 65
“Although research in CO2 capture technologies has made remarkable progress, the energy penalty for existing technologies is still high (around 50 $ per ton of CO2 avoided) [13].”
BackgroundPal, A., Chand, S., Elahi, S. M., & Das, M. C. (2017) · Dalton Transactions · doi:10.1039/c7dt03341a · Cited by 63
Structural Control of Uniform MOF-74 Microcrystals for the Study of Adsorption Kinetics
Wu, C., Chou, L., Long, L., Si, X., Lo, W., Tsung, C., & Li, T. (2019) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.9b13965 · Cited by 64
Intensification of CO2 absorption using MDEA-based nanofluid in a hollow fibre membrane contactor
Cao, Y., Rehman, Z. U., Ghasem, N. M., Al-Marzouqi, M. H., Abdullatif, N., Nakhjiri, A. T., Ghadiri, M., Rezakazemi, M., Marjani, A., Pishnamazi, M., et al. (2021) · Scientific Reports · doi:10.1038/s41598-021-82304-2 · Cited by 63
“Velocity field is computed using27: (3) ∂CCO2 ∂t = −∇NCO2 + RCO2”
Potential of ultramicroporous metal–organic frameworks in CO 2 clean-up
Shalini, S., Nandi, S., Justin, A., Maity, R., & Vaidhyanathan, R. (2018) · Chemical Communications · doi:10.1039/c8cc03233e · Cited by 63
He, C., Wang, Y., Chen, Y., Wang, X., Yang, J., Li, L., & Li, J. (2020) · Chemical Engineering Journal · doi:10.1016/j.cej.2020.126428 · Cited by 61
Economic Comparison of Three Gas Separation Technologies for CO2 Capture from Power Plant Flue Gas
Yang, H., Fan, S., Lang, X., Wang, Y., & Nie, J. (2011) · Chinese Journal of Chemical Engineering · doi:10.1016/s1004-9541(11)60031-1 · Cited by 60
Ullah, R., Atilhan, M., Aparício, S., Canlier, A., & Yavuz, C. T. (2015) · International journal of greenhouse gas control · doi:10.1016/j.ijggc.2015.09.013 · Cited by 60
Iyer, S. S., Bajaj, I., Balasubramanian, P., & Hasan, M. M. F. (2017) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.7b01688 · Cited by 60
Large‐scale optimization strategies for pressure swing adsorption cycle synthesis
Dowling, A. W., Vetukuri, S. R. R., & Biegler, L. T. (2012) · AIChE Journal · doi:10.1002/aic.13928 · Cited by 59
“This pattern would repeat until either (1) the maximum number of IPOPT iterations were reached; (2) the numerical integrator reached the maximum number of integration steps per PSA cycle, returned erroneous results and subsequently causing either the IPOPT line search or restoration phase to fail; or (3) IPOPT converg…”
BackgroundColloidal processing and CO2 capture performance of sacrificially templated zeolite monoliths
Akhtar, F., Andersson, L., Keshavarzi, N., & Bergström, L. (2012) · Applied Energy · doi:10.1016/j.apenergy.2011.12.064 · Cited by 62
“Recently, the adsorption driven technologies have been proposed for CO2 capture from power plant flue gas at much reduced energy penalty [12–14].”
BackgroundHydrogen production from food wastes and gas post-treatment by CO2 adsorption
Redondas, V., Gómez, X., García, S., Pevida, C., Rubiera, F., Morán, A., & Pis, J. J. (2011) · Waste Management · doi:10.1016/j.wasman.2011.09.003 · Cited by 59
Porous organic frameworks for carbon dioxide capture and storage
Kundu, N., & Sarkar, S. (2021) · Journal of environmental chemical engineering · doi:10.1016/j.jece.2021.105090 · Cited by 62
Influence of oxidation upon the CO2 capture performance of a phenolic-resin-derived carbon
Plaza, M. G., Thurecht, K. J., Pevida, C., Rubiera, F., Pis, J. J., Snape, C. E., & Drage, T. C. (2013) · Fuel Processing Technology · doi:10.1016/j.fuproc.2013.01.011 · Cited by 58
Liu, H., Wang, J., Chen, G., Liu, B., Dandekar, A. Y., Wang, B., Zhang, X., Sun, C., & Ma, Q.-L. (2014) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2014.03.094 · Cited by 58
Khoshraftar, Z., Ghaemi, A., & Hemmati, A. (2024) · Scientific Reports · doi:10.1038/s41598-024-55836-6 · Cited by 63
Jo, D. H., Jung, H., Shin, D. K., Lee, C. H., & Kim, S. H. (2014) · Separation and Purification Technology · doi:10.1016/j.seppur.2014.01.048 · Cited by 56
Xu, C., Ruan, C., Li, Y., Lindh, J., & Strømme, M. (2017) · Advanced Sustainable Systems · doi:10.1002/adsu.201700147 · Cited by 61
Protic/aprotic ionic liquids for effective CO2 separation using supported ionic liquid membrane
Swati, I. K., Sohaib, Q., Cao, S., Younas, M., Liú, D., Gui, J., & Rezakazemi, M. (2020) · Chemosphere · doi:10.1016/j.chemosphere.2020.128894 · Cited by 56
Solar-assisted pressure-temperature swing adsorption for CO2 capture: Effect of adsorbent materials
Zhao, R., Zhao, L., Wang, S., Deng, S., Li, H., & Yu, Z. (2018) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2018.06.004 · Cited by 56
Delgado, M. R., & Areán, C. O. (2011) · Energy · doi:10.1016/j.energy.2011.06.033 · Cited by 56
“Among them, porous solids constitute a main line of research [15,16].”
BackgroundPotentials and limitations of direct air capturing in the built environment
Baus, L., & Nehr, S. (2021) · Building and Environment · doi:10.1016/j.buildenv.2021.108629 · Cited by 60
Sun, J., Li, H., Liu, Q., Zhong, W., & Dong, W. (2025) · Chemical Engineering Journal · doi:10.1016/j.cej.2025.165890 · Cited by 70
Nguyen, N. T. T., Furukawa, H., Gándara, F., Hoàng, N. T., Cordova, K. E., & Yaghi, O. M. (2014) · Angewandte Chemie · doi:10.1002/ange.201403980 · Cited by 54
Reversible CO 2 Capture and On-Demand Release by an Acidity-Matched Organic Photoswitch
Alfaraidi, A. M., Kudisch, B. J., Ni, N., Thomas, J., George, T. Y., Rajabimoghadam, K., Jiang, H. J., Nocera, D. G., Aziz, M. J., & Liu, R. Y. (2023) · Journal of the American Chemical Society · doi:10.1021/jacs.3c08471 · Cited by 57
Aziz, B., Zhao, G., & Hedin, N. (2011) · Langmuir · doi:10.1021/la104629m · Cited by 54
Mesfer, M. K. A. (2020) · Environmental Science and Pollution Research · doi:10.1007/s11356-020-07934-x · Cited by 54
Metal-organic framework based carbon capture and purification technologies for clean environment
Mukherjee, S., Kumar, A., & Zaworotko, M. J. (2019) · Elsevier eBooks · doi:10.1016/b978-0-12-814633-0.00003-x · Cited by 56
Sharma, S., Balestra, S. R. G., Baur, R., Agarwal, U., Zuidema, E., Rigutto, M. S., Calero, S., Vlugt, T. J. H., & Dubbeldam, D. (2023) · Molecular Simulation · doi:10.1080/08927022.2023.2202757 · Cited by 60
Du, J., Cao, H., Li, Y., Yang, Z., Eslamimanesh, A., Fakhroleslam, M., Mansouri, S. S., & Shen, W. (2023) · Chemical Engineering Science · doi:10.1016/j.ces.2023.119379 · Cited by 58
Nalaparaju, A., Khurana, M., Farooq, S., Karimi, I. A., & Jiang, J. (2014) · Chemical Engineering Science · doi:10.1016/j.ces.2014.09.054 · Cited by 52
Evaluation of MIL-47(V) for CO 2 -Related Applications
Llewellyn, P. L., Bourrelly, S., Vagner, C., Heymans, N., Leclerc, H., Ghoufi, A., Bazin, P., Vimont, A., Daturi, M., Devic, T., et al. (2012) · The Journal of Physical Chemistry C · doi:10.1021/jp308525k · Cited by 51
A techno-economic evaluation of anaerobic biogas producing systems in developing countries
Morgan, H. M., Xie, W., Liang, J., Mao, H., Lei, H., Ruan, R. R., & Bu, Q. (2017) · Bioresource Technology · doi:10.1016/j.biortech.2017.12.013 · Cited by 55
CO 2 conversion in non-thermal plasma and plasma/g-C 3 N 4 catalyst hybrid processes
Lu, N., Sun, D., Zhang, C., Jiang, N., Shang, K., Bao, X., Li, J., & Wu, Y. (2018) · Journal of Physics D Applied Physics · doi:10.1088/1361-6463/aaa919 · Cited by 51
Carbon dioxide capture in the presence of water by an amine-based crosslinked porous polymer
Abdelnaby, M. M., Alloush, A. M., Qasem, N. A. A., Al‐Maythalony, B. A., Mansour, R. B., Cordova, K. E., & Hamouz, O. C. S. A. (2018) · Journal of Materials Chemistry A · doi:10.1039/c8ta00012c · Cited by 55
Dasgupta, S., Biswas, N., Aarti, A., Gode, N. G., Divekar, S., Nanoti, A., & Goswami, A. N. (2011) · International journal of greenhouse gas control · doi:10.1016/j.ijggc.2011.10.007 · Cited by 50
“In this context adsorption processes using Pressure r Vacuum Swing Adsorption (PSA/VSA), are attracting interest as nergy requirements are lower (Ho et al., 2008).”
MethodEfficiency of hydrogen recovery from reformate with a polymer electrolyte hydrogen pump
Abdulla, A., Laney, K., Padilla, M., Sundaresan, S., & Benziger, J. B. (2010) · AIChE Journal · doi:10.1002/aic.12406 · Cited by 50
Jung, W., Park, J., Won, W., & Lee, K. S. (2018) · Energy · doi:10.1016/j.energy.2018.03.022 · Cited by 51
Optimization and analysis of a VPSA process for N2/CH4 separation
Yang, H., Yin, C., Jiang, B., & Zhang, D. (2014) · Separation and Purification Technology · doi:10.1016/j.seppur.2014.07.047 · Cited by 49
“conducted a sensitivity analysis to show the influence of the process cycle, operation pressure, and adsorbent characteristics on the cost of CO2 capture [11].”
BackgroundZanobetti, F., Pio, G., Bucelli, M., Miani, L., Jafarzadeh, S., & Cozzani, V. (2024) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2024.143343 · Cited by 53
CO2 adsorbent pellets produced from pine sawdust: Effect of coal tar pitch addition
Plaza, M. G., Durán, I., Rubiera, F., & Pevida, C. (2015) · Applied Energy · doi:10.1016/j.apenergy.2014.12.090 · Cited by 48
“Adsorption separation processes seek to reduce the energy penalty of the capture step compared to the amine scrubbing alternative [16-18].”
BackgroundXu, D. Y., Zhang, J., Li, G., Xiao, P., Webley, P. A., & Yu-chun, Z. (2011) · Journal of Fuel Chemistry and Technology · doi:10.1016/s1872-5813(11)60016-9 · Cited by 49
Prats, H., Bahamón, D., Alonso, G., Giménez, X., Gamallo, P., & Sayós, R. (2017) · Journal of CO2 Utilization · doi:10.1016/j.jcou.2017.03.007 · Cited by 49
Zhao, X., & You, F. (2020) · AIChE Journal · doi:10.1002/aic.17127 · Cited by 48
Green coffee based CO2 adsorbent with high performance in postcombustion conditions
Plaza, M. G., González, A. S., Pevida, C., & Rubiera, F. (2015) · Fuel · doi:10.1016/j.fuel.2014.10.014 · Cited by 47
“Moreover, the minimum pressure achieved during the here presented cycles (5-10 kPa) is relatively large, and has been proposed as the optimal value to minimize the cost of postcombustion CO2 capture [9].”
BackgroundChanges in Porous Parameters of the Ion Exchanged X Zeolite and Their Effect on CO2 Adsorption
Gęsikiewicz-Puchalska, A., Zgrzebnicki, M., Michalkiewicz, B., Kałamaga, A., Narkiewicz, U., Morawski, A. W., & Wróbel, R. J. (2021) · Molecules · doi:10.3390/molecules26247520 · Cited by 50
“Adsorption with solid sorbents followed by underground storage, so-called carbon capture and storage (CCS), is one of the most promising options to reduce CO2 emission [9].”
BackgroundA Systematic Review of Amino Acid-Based Adsorbents for CO2 Capture
Hatta, N. S. M., Aroua, M. K., Hussin, F., & Gew, L. T. (2022) · Energies · doi:10.3390/en15103753 · Cited by 47
Park, J.-W., Heo, S., Yeo, J.-G., Lee, S., Kim, J., & Lee, J. H. (2025) · Membranes · doi:10.3390/membranes15070200 · Cited by 52
Pith based spherical activated carbon for CO2 removal from flue gases
Wang, Z., Zhan, L., Ge, M., Xie, F., Wang, Y., Qiao, W., Liang, X., & Ling, L. (2011) · Chemical Engineering Science · doi:10.1016/j.ces.2011.06.070 · Cited by 48
Bazhenov, S. D., Леонидович, Б. И., Bakhtin, D. S., Rybakova, A. N., Khotimskiy, V. S., Molchanov, S. P., & Volkov, V. V. (2016) · Green Energy & Environment · doi:10.1016/j.gee.2016.10.002 · Cited by 46
Jeong, S., Kim, D., Shin, S., Moon, D., Cho, S. J., & Lah, M. S. (2014) · Chemistry of Materials · doi:10.1021/cm404239s · Cited by 45
Ahmed, E., Deep, A., Kwon, E. E., Brown, R. J. C., & Kim, K. (2016) · Scientific Reports · doi:10.1038/srep31283 · Cited by 45
A novel process for direct solvent regeneration via solar thermal energy for carbon capture
Khalilpour, K. R., Milani, D., Qadir, A., Chiesa, M., & Abbas, A. (2016) · Renewable Energy · doi:10.1016/j.renene.2016.12.001 · Cited by 45
Mixed Matrix Membranes Based on Metal–Organic Frameworks with Tunable Pore Size for CO 2 Separation
Fan, L., Kang, Z., Shen, Y., Wang, S., Zhao, H., Sun, H., Hu, X., Sun, H., Wang, R., & Sun, D. (2018) · Crystal Growth & Design · doi:10.1021/acs.cgd.8b00307 · Cited by 45
Matito-Martos, I., Sepulveda, C., Gómez-Serrano, C., Acién, F. G., Perez-Carbajo, J., Delgado, J. A., Águeda, V. I., Ania, C. O., Parra, J. B., Calero, S., et al. (2020) · Chemical Engineering Journal · doi:10.1016/j.cej.2020.128020 · Cited by 46
A green approach towards sorption of CO2 on waste derived biochar
Kumar, A., Singh, E., Mishra, R., Lo, S., & Kumar, S. (2022) · Environmental Research · doi:10.1016/j.envres.2022.113954 · Cited by 46
Polymerized Ionic Liquid Sorbents for CO2 Separation
Samadi, A., Kemmerlin, R. K., & Husson, S. M. (2010) · Energy & Fuels · doi:10.1021/ef101027s · Cited by 44
Characterization and Performance of Direct Air Capture Sorbent
Elfving, J., Bajamundi, C., & Kauppinen, J. (2017) · Energy Procedia · doi:10.1016/j.egypro.2017.03.1746 · Cited by 50
Khalilpour, K. R., Abbas, A., Lai, Z., & Pinnau, I. (2011) · AIChE Journal · doi:10.1002/aic.12699 · Cited by 44
Are we missing something when evaluating adsorbents for CO 2 capture at the system level?
Balogun, H. A., Bahamón, D., AlMenhali, S., Vega, L. F., & AlHajaj, A. (2021) · Energy & Environmental Science · doi:10.1039/d1ee01677f · Cited by 45
Amidoxime porous polymers for CO2 capture
Zulfiqar, S., Awan, S., Karadaş, F., Atilhan, M., Yavuz, C. T., & Sarwar, M. I. (2013) · RSC Advances · doi:10.1039/c3ra42433b · Cited by 43
Gil, R. R., Ruíz, B., Lozano, M. S., & Fuente, E. (2014) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2014.09.001 · Cited by 43
Economic process design for separation of CO2 from the off-gas in ironmaking and steelmaking plants
Kim, H., Lee, J., Lee, S., Lee, I., Park, J.-H., & Han, J. (2015) · Energy · doi:10.1016/j.energy.2015.05.093 · Cited by 43
Review of Carbon Capture and Methane Production from Carbon Dioxide
Akpasi, S. O., & Isa, Y. M. (2022) · Atmosphere · doi:10.3390/atmos13121958 · Cited by 44
Li, J., & Hitch, M. (2015) · Minerals · doi:10.3390/min5020259 · Cited by 42
“1 bar) [13].”
Xu, X., Wang, J.-J., Dong, J., Li, H., Zhang, Q., & Zhao, X. Z. (2020) · Journal of Membrane Science · doi:10.1016/j.memsci.2020.117967 · Cited by 42
Influence of Water Vapor on CO2 Adsorption Using a Biomass-Based Carbon
Plaza, M. G., González, A. S., Pevida, C., & Rubiera, F. (2014) · Industrial & Engineering Chemistry Research · doi:10.1021/ie500342q · Cited by 41
Microchannel zeolite 13X adsorbent with high CO2 separation performance
Hedlund, J., García, G., Balsamo, M., Zhou, M. Y., & Mouzon, J. (2021) · Separation and Purification Technology · doi:10.1016/j.seppur.2021.119483 · Cited by 44
Cheung, O. Y. H., Wardecki, D., Bacsik, Z., Vasiliev, P., McCusker, L. B., & Hedin, N. (2016) · Physical Chemistry Chemical Physics · doi:10.1039/c6cp02443b · Cited by 41
Synthesis of bare and functionalized porous adsorbent materials for CO2 capture
Olajire, A. A. (2017) · Greenhouse Gases Science and Technology · doi:10.1002/ghg.1657 · Cited by 43
On the development of Vacuum Swing adsorption (VSA) technology for post-combustion CO2 capture
Andersen, A., Divekar, S., Dasgupta, S., Cavka, J. H., Aarti, Nanoti, A., Spjelkavik, A., Goswami, A. N., Garg, M. O., & Blom, R. (2013) · Energy Procedia · doi:10.1016/j.egypro.2013.05.082 · Cited by 41
“In this context adsorption processes using Pressure or Vacuum Swing Adsorption (PSA/VSA) are attracting interest as energy requirements are lower [1][2].”
MethodExceptional CO2Adsorbing Materials under Different Conditions
Nandi, M., & Uyama, H. (2014) · The Chemical Record · doi:10.1002/tcr.201402062 · Cited by 40
Ghosh, S., Sevilla, M., Fuertes, A. B., Andreoli, E., Ho, J., & Barron, A. R. (2016) · Journal of Materials Chemistry A · doi:10.1039/c6ta04936b · Cited by 42
Assessment of Artificial Photosynthetic Systems for Integrated Carbon Capture and Conversion
Prajapati, A., & Singh, M. R. (2019) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.8b04969 · Cited by 40
Alsuhaibani, A. S., Afzal, S., Challiwala, M. S., Elbashir, N. O., & El‐Halwagi, M. M. (2019) · Catalysis Today · doi:10.1016/j.cattod.2019.03.070 · Cited by 40
A Microporous Organic Copolymer for Selective CO 2 Capture under Humid Conditions
Abdelnaby, M. M., Qasem, N. A. A., Al‐Maythalony, B. A., Cordova, K. E., & Hamouz, O. C. S. A. (2019) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.9b02334 · Cited by 41
García, S., Gil, M. V., Pis, J. J., Rubiera, F., & Pevida, C. (2012) · International journal of greenhouse gas control · doi:10.1016/j.ijggc.2012.10.018 · Cited by 42
“For PSA processes operating under vacuum desorption conditions, the pressure ratio was shown to play a critical role in the CO2 recovery and the purity of the weakly adsorbed product (Ho et al., 2008).”
BackgroundTian, J., Shen, Y., Zhang, D., & Tang, Z. (2021) · Journal of environmental chemical engineering · doi:10.1016/j.jece.2021.106037 · Cited by 37
A review on removal CO2, SO2, and H2S from flue gases using zeolite based adsorbents
Zewdie, D. T., Bizualem, Y. D., & Nurie, A. G. (2024) · Discover Applied Sciences · doi:10.1007/s42452-024-05989-w · Cited by 44
“According to the analysis, COA amounted to $51/ton of CO 2 averted [228].”
Kumari, S., Gusain, M., Lamba, B. Y., & Kumar, S. (2025) · Journal of Materials Chemistry A · doi:10.1039/d5ta02338f · Cited by 41
Fan, Y., Kalyanaraman, J., Labreche, Y., Rezaei, F., Lively, R. P., Realff, M. J., Koros, W. J., Jones, C. W., & Kawajiri, Y. (2015) · Industrial & Engineering Chemistry Research · doi:10.1021/ie504603h · Cited by 39
Edens, S. J., McGrath, M. J., Guo, S., Du, Z., Zhou, H., Zhong, L., Shi, Z., Wan, J., Bennett, T. D., Qiao, A., et al. (2023) · Advanced Science · doi:10.1002/advs.202206437 · Cited by 41
“1 Zeolite 13X cost for literature example([51]) VSA adsorber vessel volume = 630 m3”
BackgroundSupported ionic liquids for air purification
Ramos, V. C., Han, W., Zhang, X., Zhang, S., & Yeung, K. L. (2020) · Current Opinion in Green and Sustainable Chemistry · doi:10.1016/j.cogsc.2020.100391 · Cited by 40
Review of oil palm-derived activated carbon for CO2 capture
Lai, J. Y., Ngu, L. H., Hashim, S. S., Chew, J. J., & Sunarso, J. (2021) · Carbon letters · doi:10.1007/s42823-020-00206-1 · Cited by 40
Challa, P., Paleti, G., Madduluri, V. R., Gadamani, S. B., Pothu, R., Burri, D. R., Boddula, R., Perupogu, V., & Kamaraju, S. R. R. (2022) · Catalysis Surveys from Asia · doi:10.1007/s10563-021-09352-6 · Cited by 38
Zhao, Y., Ge, H. L., Miao, Y., Chen, J., & Cai, W. (2019) · Catalysis Today · doi:10.1016/j.cattod.2019.12.016 · Cited by 37
Zhou, J., Zhao, H., Li, J., Zhu, Y., Hu, J., Liu, H., & Hu, Y. (2013) · Solid State Sciences · doi:10.1016/j.solidstatesciences.2013.07.008 · Cited by 37
Post-combustion CO2 capture adsorbents from spent coffee grounds
González, A. S., Plaza, M. G., Pis, J. J., Rubiera, F., & Pevida, C. (2013) · Energy Procedia · doi:10.1016/j.egypro.2013.05.094 · Cited by 37
A multi-scale approach for the discovery of zeolites for hydrogen sulfide removal
Liu, T., First, E. L., Hasan, M. M. F., & Floudas, C. A. (2016) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2016.03.015 · Cited by 37
Recent advances on the modeling and optimization of CO2 capture processes
Chatziasteriou, C. C., Kikkinides, E. S., & Georgiadis, M. C. (2022) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2022.107938 · Cited by 37
Seyyedattar, M., & Zendehboudi, S. (2025) · Fuel · doi:10.1016/j.fuel.2025.137276 · Cited by 42
Reducing energy consumption of advanced PTSA CO2 capture process―Experimental and numerical study
Song, C., Kansha, Y., Fu, Q., Ishizuka, M., & Tsutsumi, A. (2016) · Journal of the Taiwan Institute of Chemical Engineers · doi:10.1016/j.jtice.2015.12.006 · Cited by 37
Alamia, A., Òsk Gardarsdòttir, S., Larsson, A., Normann, F., & Thunman, H. (2017) · Energy Technology · doi:10.1002/ente.201600719 · Cited by 36
Metadata
- Authors
- Ho, M. T., Allinson, G. W., & Wiley, D. E.
- Affiliations
- UNSW Sydney (AU)
- Corresponding author
- Wiley, Dianne E.
- Venue
- Industrial & Engineering Chemistry Research
- Publisher
- American Chemical Society (ACS)
- Published
- 2008-06-17
- Volume
- 47
- Issue
- 14
- Pages
- 4883-4890
- ISSN
- 0888-5885 (ISSN-L)
- 1520-5045
- OpenAlex
- W2009040339
- Cited by
- 566
- References
- 31
- Citations by year
- 2026: 19 · 2025: 32 · 2024: 38 · 2023: 37 · 2022: 34 · 2021: 38 · 2020: 33 · 2019: 28 · 2018: 34 · 2017: 35 · 2016: 27 · 2015: 33 · 2014: 39 · 2013: 40 · 2012: 36
- FWCI
- 44.59
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Industrial & Engineering Chemistry Research (publishedVersion)
- Funders
- University of New South Wales
- Topics
- Physical Sciences › Chemical Engineering › Filtration and Separation › Carbon Dioxide Capture Technologies
- Physical Sciences › Environmental Science › Environmental Engineering › Industrial Gas Emission Control
- Physical Sciences › Environmental Science › Environmental Engineering › CO2 Sequestration and Geologic Interactions
- Keywords
- pressure swing adsorption, CO2 capture, post-combustion flue gas, vacuum desorption, zeolite 13X, capture cost, CO2/N2 selectivity, power plant emissions, sensitivity analysis
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.