Effect of pore size on carbon dioxide sorption by carbide derived carbon
The DOI matches its Crossref record; 38 of the 38 references it cites were found in a registry or an index.
Abstract
CO2 sorption at atmospheric and sub-atmospheric pressures is a key step towards carbon capture and sequestration (CCS) and materials capable of fast and efficient CO2 uptake are currently being studied extensively. Carbide-derived carbons (CDCs) show a very high sorption capacity for CO2 of up to 7.1 mol/kg at 0 °C and ambient pressure. This value is significantly higher than other carbon materials. Systematic experimental investigation of a large number of different CDCs derived from nano- and micrometer sized precursors with and without activation show a linear correlation between the CO2 uptake at a certain pressure and the pore volume. However, CO2 sorption is not limited by the total pore volume but only by pores smaller than a certain diameter. At 1 bar, pores smaller than 0.8 nm contribute the most to the CO2 uptake and at 0.1 bar pores smaller or equal to 0.5 nm are preferred. With lower total pressure, smaller pores contribute more to the measured amount of adsorbed CO2. The prediction of the CO2 uptake based on the pore volume for pores of a certain diameter is much more accurate than predictions based on the mean pore size or the specific surface area. This study provides guidelines for the design of materials with an improved ability to remove carbon dioxide from the environment at atmospheric and lower pressures.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“it has been reported that the narrow micropores play a decisive role in CO2 adsorption capacity [20-23].”
From Preparation of Microporous Carbon from Sargassum horneri by Hydrothermal Carbonization and KOH Activation for CO2 Capture (2018) · cites this paper as [22]
Citations
Cites
Adsorption of Gases in Multimolecular Layers
Brunauer, S., Emmett, P. H., & Teller, E. (1938) · Journal of the American Chemical Society · doi:10.1021/ja01269a023 · Cited by 28,156
Amine Scrubbing for CO 2 Capture
Rochelle, G. T. (2009) · Science · doi:10.1126/science.1176731 · Cited by 4,440
Anomalous Increase in Carbon Capacitance at Pore Sizes Less Than 1 Nanometer
Chmiola, J., Yushin, G., Gogotsi, Y., Portet, C., Simon, P., & Taberna, P. L. (2006) · Science · doi:10.1126/science.1132195 · Cited by 4,022
Self-citationRecommendations for the characterization of porous solids (Technical Report)
Rouquerol, J., Avnir, D., Fairbridge, C. W., Everett, D. H., Haynes, J. M., Pernicone, N., Ramsay, J. D. F., Sing, K. S. W., & Unger, K. K. (1994) · Pure and Applied Chemistry · doi:10.1351/pac199466081739 · Cited by 3,984
Adsorbent Materials for Carbon Dioxide Capture from Large Anthropogenic Point Sources
Choi, S., Drese, J. H., & Jones, C. W. (2009) · ChemSusChem · doi:10.1002/cssc.200900036 · Cited by 2,596
Caskey, S. R., Wong-Foy, A. G., & Matzger, A. J. (2008) · Journal of the American Chemical Society · doi:10.1021/ja8036096 · Cited by 1,815
Is the bet equation applicable to microporous adsorbents?
(2007) · Studies in Surface Science and Catalysis · doi:10.1016/s0167-2991(07)80008-5 · Cited by 1,147
The reaction of CO2 with ethanolamines
Danckwerts, P. V. (1979) · Chemical Engineering Science · doi:10.1016/0009-2509(79)85087-3 · Cited by 1,116
Yazaydın, A. Ö., Snurr, R. Q., Park, T.-H., Koh, K., Liu, J., LeVan, M. D., Benin, A. I., Jakubczak, P., Lanuza, M., Galloway, D. B., et al. (2009) · Journal of the American Chemical Society · doi:10.1021/ja9057234 · Cited by 907
Dietzel, P. D. C., Besikiotis, V., & Blom, R. (2009) · Journal of Materials Chemistry · doi:10.1039/b911242a · Cited by 689
Cited by
Items 601–679 of 679
Porous Carbon Materials for Carbon Dioxide Capture
Liu, Z. M., Fu, C., Qi, T., Zhou, H., Hao, G., Guo, Y., & Hu, G. (2026) · Carbon Energy · doi:10.1002/cey2.70229 · Cited by 6
Ultramicroporous N-doped carbons prepared by KHC2O4 activation for CO2 adsorption
Yin, Y., Wang, Y., Li, Z. S., Liu, Y. C., Zhao, L., Demir, M., Zaid, A., Wang, L., & Hu, X. (2026) · Journal of environmental chemical engineering · doi:10.1016/j.jece.2026.124231 · Cited by 4
Cobalt‐catalyzed tunable carbon microstructures from halogenated SiC preceramic precursors
Tamayo, A., Rodriguez, M. A., Rubio, F., & Rubio, J. (2022) · Journal of the American Ceramic Society · doi:10.1111/jace.18436 · Cited by 4
The role of biogenic waste composition on pyrolysis: Part I – Char properties
Gil, Á. N., Fonts, Ì., Ruiz, J., Ceamanos, J., Gil-Lalaguna, N., Murillo, M. B., & Gea, G. (2025) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2025.107778 · Cited by 7
Hussin, F., Hatta, N. S. M., Lam, S. E., & Aroua, M. K. (2025) · Greenhouse Gases Science and Technology · doi:10.1002/ghg.2377 · Cited by 3
Daud, N. K., Abdullah, H., & Ismail, N. A. (2026) · BULLETIN OF CHEMICAL REACTION ENGINEERING AND CATALYSIS · doi:10.9767/bcrec.20658 · Cited by 3
“Since nitrogen adsorption at cryogenic temperature is diffusion-sensitive [30], even partial pore obstruction can substantially reduce the measured surface area.”
Upcycling polyethylene into self-supported carbon nanofibers for efficient CO2 capture
Garduque, R. G., Qiao, Y., & Wang, J. (2026) · Carbon · doi:10.1016/j.carbon.2026.121576 · Cited by 3
Engineering sub-nanometer pore networks in biomass-derived carbons for CF4 adsorption
Wang, Y., Hao, Z., Zhao, M., Jiang, Y., Xiao, Q., Zhao, L., Demir, M., Şimşek, U. B., Wang, L., & Hu, X. (2026) · Chemical Engineering Science · doi:10.1016/j.ces.2026.124196 · Cited by 3
The role of biogenic waste composition on pyrolysis: Part II – Char CO2 adsorption capacity
Gil, Á. N., Fonts, Ì., Ruiz, J., Ceamanos, J., Gil-Lalaguna, N., Ábrego, J., & Gea, G. (2025) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2025.107775 · Cited by 4
Gorai, T., Thanasekar, C., Kumar, P., Babu, A., Kurungot, S., & Vinod, C. P. (2025) · Chemistry - A European Journal · doi:10.1002/chem.202500873 · Cited by 3
Alkali-metal-carbonate-based CO2 Adsorbents
Kanoh, H., & Luo, H. (2018) · Royal Society of Chemistry eBooks · doi:10.1039/9781788013352-00206 · Cited by 3
Kim, M. H., Choi, S. O., & Choo, S. T. (2019) · Carbon letters · doi:10.1007/s42823-019-00055-7 · Cited by 3
Brute force determination of the optimum pore sizes for CO 2 uptake in turbostratic carbons
Blankenship, L. S., Albeladi, N., Alkhaldi, T., Madkhali, A., & Mokaya, R. (2022) · Energy Advances · doi:10.1039/d2ya00149g · Cited by 5
Functionalized and improved polymeric adsorbents
Penchah, H. R. (2023) · Elsevier eBooks · doi:10.1016/b978-0-323-99746-1.00008-2 · Cited by 3
Carbon dioxide storage and separation using Ca-decorated C48B12 fullerene: A DFT study
Mouselchi, B., Esrafili, M. D., & Bahrami, A. (2024) · Results in Chemistry · doi:10.1016/j.rechem.2024.101792 · Cited by 3
Feng, X., Long, H., Yue, C., Qiu, S., Tang, Q., & Liu, L. (2025) · Nuclear Engineering and Technology · doi:10.1016/j.net.2025.103704 · Cited by 2
Pham, H. K., Phuong, M., & Srinivasan, M. (2025) · Sustainable materials and technologies · doi:10.1016/j.susmat.2025.e01801 · Cited by 2
Asawarungruengchai, P., Sakulaue, P., Deshsorn, K., Iamprasertkun, P., Kaothanthong, N., & Nueangnoraj, K. (2026) · Journal of CO2 Utilization · doi:10.1016/j.jcou.2026.103316 · Cited by 3
Mn-Based Single Atoms and Nanocrystal Carbon Aerogels for CO 2 Capture and Energy Storage
Skaria, J. M., Rao, S., Sabri, Y. M., Sankarankutty, A. K., & Sarathchandran, C. (2026) · ACS Applied Nano Materials · doi:10.1021/acsanm.5c04928 · Cited by 2
Guo, D., Feng, D., Zhang, Y., Zhang, Y., Zhao, Y., Gao, J., & Sun, S. (2026) · The Innovation Energy · doi:10.59717/j.xinn-energy.2026.100131 · Cited by 2
Khan, M. F. H., Ahmed, I., Shovon, S. M., Akash, F. A., Leon, T. I., Rahman, A., & Chanda, R. K. (2026) · International Journal of Green Energy · doi:10.1080/15435075.2026.2637734 · Cited by 4
“Therefore, the abundance of ultra-micropores is more critical to the adsorption capacity than the total pore volume or surface area (Montoya et al. 2003; Presser et al. 2011; Wickramaratne and Jaroniec 2013).”
Momeni, M., Haddadi, S. A., Soltanian, S., Zamani, S. M., Mekonnen, T. H., Chen, A., & Dutta, A. (2026) · Journal of Environmental Management · doi:10.1016/j.jenvman.2026.131011 · Cited by 2
Işınkaralar, K. (2022) · Sakarya University Journal of Science · doi:10.16984/saufenbilder.1051342 · Cited by 2
Effect of Porous Carbons’ Intrinsic Parameters on the Pressure Swing Adsorption of CO2 from Biogas
Wilson, S. M. W., & Barrette, S. (2022) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.2c01657 · Cited by 2
Yao, Y., Zhuo, H., Xu, J., Yang, X., & Huang, Y. (2024) · RSC Advances · doi:10.1039/d3ra08430b · Cited by 2
Purification and upgrade of biogas using biomass-derived adsorbents: Review
Mulu, E., M’Arimi, M. M., & Rose, R. C. (2022) · CRC Press eBooks · doi:10.1201/9781003221968-38 · Cited by 3
Kausar, H., Bacsik, Z., & Hedin, N. (2022) · Materials Chemistry and Physics · doi:10.1016/j.matchemphys.2022.127283 · Cited by 3
Engineering Biochar-Based Materials for Carbon Dioxide Adsorption and Separation
Gao, S., Shee, J., Chen, W., Xu, L., Dong, C., & Song, B. (2023) · Biofuels and biorefineries · doi:10.1007/978-981-99-4580-1_8 · Cited by 1
Zinc-Decorated and Nitrogen-Functionalized Hierarchical Porous Carbons for Carbon Dioxide Capture
Chiang, Y., Chin, W.-T., & Chu, I.-C. (2025) · Applied Sciences · doi:10.3390/app15105743 · Cited by 1
“In particular, porous carbons characterized with micropores [4,5] and heteroatom surface functional groups [6,7] have been recommended for CO 2 capture.”
Zuo, J., Sun, F., Qu, Z., Yang, C.-W., Xie, L., Zhang, Y., Li, X., & Li, J. (2025) · Carbon Capture Science & Technology · doi:10.1016/j.ccst.2025.100445 · Cited by 7
Ultramicroporous carbon materials preparation via one-step pyrolysis of biomass
Ren, X., Gao, Y., He, W., Yang, S., & Yin, G. (2025) · Chemical Engineering Science · doi:10.1016/j.ces.2025.122820 · Cited by 1
Absor, M. A. U., Lukmantoro, A., Sari, F. D., Hamidah, N. L., & Darmawan, A. (2025) · Surfaces and Interfaces · doi:10.1016/j.surfin.2025.108296 · Cited by 5
Influence of ultramicroporosity and surface chemistry on dynamic CO2 capture in activated carbons
Gooijer, S., Goosen, P., Díaz-Maroto, C. G., Moreno, I., Calero, S., Fermoso, J., & Vicent‐Luna, J. M. (2026) · Separation and Purification Technology · doi:10.1016/j.seppur.2026.140098 · Cited by 1
“[5, 6] Beyond textural properties, the bulk composition of the carbons also reveals relevant differences between both materials.”
Yin, Y., Xu, Y., Ye, Z., Liu, Y., Hu, X., Jiang, Y., Zhao, L., Demir, M., Mesfer, M. K. A., Xiao, Q., et al. (2026) · Fuel · doi:10.1016/j.fuel.2026.140742 · Cited by 1
Integrated frameworks: Rational sorbent selection for efficient CO₂ capture
Ali, A., Moradian, J. M., Rasheed, T., Vasudev, V., Tahir, M. H., Haq, F., Keerio, H. A., Guo, L. Q., & Zhang, S. (2026) · Journal of environmental chemical engineering · doi:10.1016/j.jece.2026.124623 · Cited by 2
NMR Characterization of Super-capacitors
Wang, H., & Griffin, J. M. (2021) · Royal Society of Chemistry eBooks · doi:10.1039/9781839160097-00391 · Cited by 1
CO2 capture from the atmospheric air using nanomaterials
Al‐Hinaai, M. M. (2022) · Elsevier eBooks · doi:10.1016/b978-0-323-89782-2.00015-6 · Cited by 1
Technologies to Capture CO$_2$ directly from Ambient AirPreprint
Lee, G. A., Shi, X., & Park, A. A. (2022) · arXiv (Cornell University) · doi:10.48550/arxiv.2211.00791 · Cited by 3
Gas-Adsorbing Nanoporous Carbons
Lozano‐Castelló, D., Suárez‐García, F., Alcañiz-Monge, J., Cazorla‐Amorós, D., & Linares-Solano, A. (2018) · CRC Press eBooks · doi:10.1201/9781315371337-21 · Cited by 2
Heo, Y., Zhang, Y., Rhee, K. Y., Park, S., & Hui, D. (2018) · Composites Part B Engineering · doi:10.1016/j.compositesb.2018.04.040
Koyuncu, D. D. E., Yaşyerli, S., & Yaşyerli, N. (2020) · Pamukkale University Journal of Engineering Sciences · doi:10.5505/pajes.2019.33858
“[18] Presser V, McDonough J, Yeon S-H, Gogotsi Y.”
Backgrounddos Santos, D. S. (2019) · University of Birmingham Institutional Research Archive (University of Birmingham) · Cited by 1
Gas-Adsorbing Nanoporous Carbons
Lozano‐Castelló, D., Suárez‐García, F., Alcañiz-Monge, J., Cazorla‐Amorós, D., & Linares-Solano, A. (2016) · CRC Press eBooks · doi:10.1201/b19568-26
Ding, J., Xue, H., Xu, Y., Song, L., Gong, H. R., Fan, X., Chang, K., Huang, X., Wang, T., & He, J. (2021) · SSRN Electronic Journal · doi:10.2139/ssrn.3974814
Pornaroontham, P. (2018) · Chula Digiverse · doi:10.58837/chula.the.2018.85
Design of Porous Carbon Adsorbents from Ethylene Glycol for Selective CO 2 Adsorption
Zaman, A. C., & Üstündağ, C. B. (2024) · ChemistrySelect · doi:10.1002/slct.202302378
Lin, Z., Li, Y., & He, X. (2024) · Elsevier eBooks · doi:10.1016/b978-0-323-99311-1.00014-3
Xie, X., Meng, S., Gan, F., Dai, Z., He, J., Chang, Y., Jiang, X., & Jin, Z. (2024) · SSRN Electronic Journal · doi:10.2139/ssrn.4796013
Gas adsorption and storage of nanofibers and their composites
Dávila-Guzmán, N. E., Loredo‐Cancino, M., Pioquinto-García, S., & Rico-Barragán, A. A. (2024) · Elsevier eBooks · doi:10.1016/b978-0-443-14128-7.00015-8
Engineering microporous humins derived from glucosamine for CO2 adsorption
Wang, S., Zhang, H., Shao, Z., & Liu, L. (2025) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2025.108346
Optimization of adsorption capacity for CO2/N2 mixture via RSM and machine learning
Khan, M. F. A. M., & Ghaemi, A. (2025) · Chemical Engineering Journal Advances · doi:10.1016/j.ceja.2025.100957
Online monitoring of gas-liquid dispersion in a tubular reactor using passive acoustic emission
Della Vecchia, L. (2024) · AMS Laurea Institutional Research Repository (University of Bologna)
Nitrogen doping of porous carbons derived from CaCO3 nanofluids for enhanced CO2 adsorption.
Xiao, H., Li, M., Qin, Y., Tong, Z., & Lishuo, L. (2026) · Separation and Purification Technology · doi:10.1016/j.seppur.2026.136961
Enhancing CO₂ adsorption of activated carbon via nitrogen doping: Synthesis and characterization
Azizov, E. M., Feyziyeva, S., Guliyeva, N. A., Israfilov, N. V., Louis, B., & Pronkin, S. (2026) · Total environment engineering. · doi:10.1016/j.teengi.2026.100069
Programmable hourglass nanochannels in thermally rearranged copolyimides for advanced gas separation
Wang, H., Zhang, Y., Li, H., Luo, S., & Wei, X. (2026) · Separation and Purification Technology · doi:10.1016/j.seppur.2026.137141
Kumar, R., Sree Harsha Bharadwaj, H., Ranganathan, R., & Ghoroi, C. (2026) · Surfaces and Interfaces · doi:10.1016/j.surfin.2026.108833 · Cited by 2
Innovative biobased materials in carbon capture technologies
Kumar, S., Sonowal, K., Dutta, A., Singh, S. B., Tchummegne, I. K., Dharanikota, N. P. S. K., & Mandal, B. (2026) · Elsevier eBooks · doi:10.1016/b978-0-443-36538-6.00010-3 · Cited by 1
Adsorption of CO 2 on Vermiculite‐Derived Samples
Wal, K., Lorenc-Grabowska, E., Cybińska, J., & Rutkowski, P. (2026) · ChemPhysChem · doi:10.1002/cphc.202500596
Wal, K. (2025) · Prace Naukowe Uniwersytetu Ekonomicznego we Wrocławiu
Élaboration de matériaux carbonés par carbonisation eutecticothermale
Bessière, G. (2014) · theses.fr (ABES) · doi:10.70675/9b97475cz79d3z4bc9z8f11z57c60e3ed8b5
Adsorption and Separation of Carbon Dioxide for Biomethane Production : The Use of Activated Carbons
Mancilla, J. D. P. (2019) · theses.fr (ABES) · doi:10.70675/b609e51bz6846z4f0czb766z39383a5a6ee7 · Cited by 3
Bakara, I. U., Nurhafizah, M. D., Azahar, A. A., & Noorashrina, H. A. (2026) · Comments on Inorganic Chemistry · doi:10.1080/02603594.2026.2655687
Metal phosphonates for CO2 capture and conversion
Taddei, M. (2026) · Elsevier eBooks · doi:10.1016/b978-0-443-44447-0.00007-5
Qiu, F., Cui, C., Ma, M., Lu, W., Feng, H., Wang, J., Gao, C., Yao, H., & Qian, W. (2026) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.6c06118
Abbaspour, N., Korus, A., Gholizadeh, T., Kuloglija, S., Jagiełło, J., Harasek, M., Szlęk, A., & Winter, F. (2026) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2026.109745
Development of Shale Inhibitors for Water Based Fluids: Synthesis, and Evaluation Studies
IBRAHIM, M. (2020) · Research Publication Repository of King Fahd University of Petroleum and Minerals (King Fahd University of Petroleum and Minerals)
Ma, W., Huang, G. Q., Wang, Z., Chen, Y., Yu, J., Shen, Q., Zhou, X. Y., Yang, K., Tan, A., & Wang, Y. (2026) · Journal of Power Sources · doi:10.1016/j.jpowsour.2026.240976
Lignin-derived carbon materials for a sustainable CO2 economy
Kirali, A. A. B., Manickavasagam, G., Oh, W.-D., & He, C. (2026) · npj Materials Sustainability · doi:10.1038/s44296-026-00118-7
Pina, V. G. S. S., Vallés, A. C., Mateu-Campos, J., & Zanatta, M. (2026) · Energy & Fuels · doi:10.1021/acs.energyfuels.6c02910
Cheng, S., Yu, J., Tian, H., Liu, L., Huang, J., & Bai, Y. (2026) · Separation and Purification Technology · doi:10.1016/j.seppur.2026.140244
Hitesh, V. V., Palak, J. P., Pradeep, V., & Khushbu, G. P. (2026) · Clean energy and sustainability · doi:10.70322/ces.2026.10020
Active Learning-Guided Optimization of Moisture Swing Adsorption for Direct Air Capture
Yu, P., Zhang, K., Shi, X., Zheng, Z., & Zhang, H. J. (2026) · Environmental Science & Technology · doi:10.1021/acs.est.6c07244
Maruccia, E. (2022) · PORTO@Iris · Cited by 1
Phayutcharoenkun, P., Rajendran, C., Akindoye, S. B., Ponnan, S., Phan, A. N., Arpornwichanop, A., & Prasertcharoensuk, P. (2026) · RSC Advances · doi:10.1039/d6ra07411a
Yukun, J. I., Yang, C., Han, X., Li, X., Cui, X., Yang, Y., Hu, C., He, L., Jia, B., & Vandeginste, V. (2026) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2026.148653
Nitrogen-doped activated carbon from palmyrah kernel shell biomass for efficient CO2 capture
Ilamurugan, V., & Ali, B. M. J. (2026) · Environmental Science and Pollution Research · doi:10.1007/s11356-026-38332-4
Marvi, M. H., Mohseni, M. M., Rashidi, A., & Taheri, A. (2026) · Bioresource Technology Reports · doi:10.1016/j.biteb.2026.103204
Sustainable Valorization of Drinking Water Treatment Sludge: A Review
Bensaddik, M., Bensitel, N., Yaacoubi, C. E., Hammoudani, Y. E., Azar, F.-Z., & Kasmi, A. E. (2026) · Sustainability · doi:10.3390/su182211592
Ngo, H. L., Nguyễn, T. N., Tùng, N. T., Truong, C. C., Truong, B. N., Nguyen, T.-A. N., Bui, T. H., & Nguyen, T. H. (2026) · RSC Advances · doi:10.1039/d6ra08327g
Metadata
- Authors
- Presser, V., McDonough, J., Yeon, S.-H., & Gogotsi, Y.
- Affiliations
- Drexel University (US)
- Korea Institute of Energy Research (KR)
- Corresponding author
- Gogotsi, Yury
- Venue
- Energy & Environmental Science
- Publisher
- Royal Society of Chemistry (RSC)
- Published
- 2011
- Volume
- 4
- Issue
- 8
- Pages
- 3059
- ISSN
- 1754-5692 (ISSN-L)
- 1754-5706
- OpenAlex
- W2170455260
- Cited by
- 668
- References
- 38
- Citations by year
- 2026: 36 · 2025: 43 · 2024: 39 · 2023: 42 · 2022: 65 · 2021: 47 · 2020: 43 · 2019: 57 · 2018: 56 · 2017: 57 · 2016: 55 · 2015: 47 · 2014: 35 · 2013: 31 · 2012: 13
- FWCI
- 45.92
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Energy & Environmental Science (publishedVersion)
- Topics
- Physical Sciences › Chemical Engineering › Filtration and Separation › Carbon Dioxide Capture Technologies
- Physical Sciences › Environmental Science › Environmental Engineering › CO2 Sequestration and Geologic Interactions
- Physical Sciences › Chemistry › Physical and Theoretical Chemistry › Adsorption, diffusion, and thermodynamic properties of materials
- Keywords
- carbide-derived carbon, CO2 sorption, pore size, carbon capture and storage, sub-atmospheric pressure, pore volume, micropores, activation, specific surface area, CO2 adsorption capacity
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.