Effect of pore size on carbon dioxide sorption by carbide derived carbon
The DOI matches its Crossref record; 38 of the 38 references it cites were found in a registry or an index.
Abstract
CO2 sorption at atmospheric and sub-atmospheric pressures is a key step towards carbon capture and sequestration (CCS) and materials capable of fast and efficient CO2 uptake are currently being studied extensively. Carbide-derived carbons (CDCs) show a very high sorption capacity for CO2 of up to 7.1 mol/kg at 0 °C and ambient pressure. This value is significantly higher than other carbon materials. Systematic experimental investigation of a large number of different CDCs derived from nano- and micrometer sized precursors with and without activation show a linear correlation between the CO2 uptake at a certain pressure and the pore volume. However, CO2 sorption is not limited by the total pore volume but only by pores smaller than a certain diameter. At 1 bar, pores smaller than 0.8 nm contribute the most to the CO2 uptake and at 0.1 bar pores smaller or equal to 0.5 nm are preferred. With lower total pressure, smaller pores contribute more to the measured amount of adsorbed CO2. The prediction of the CO2 uptake based on the pore volume for pores of a certain diameter is much more accurate than predictions based on the mean pore size or the specific surface area. This study provides guidelines for the design of materials with an improved ability to remove carbon dioxide from the environment at atmospheric and lower pressures.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“it has been reported that the narrow micropores play a decisive role in CO2 adsorption capacity [20-23].”
From Preparation of Microporous Carbon from Sargassum horneri by Hydrothermal Carbonization and KOH Activation for CO2 Capture (2018) · cites this paper as [22]
Citations
Cites
Adsorption of Gases in Multimolecular Layers
Brunauer, S., Emmett, P. H., & Teller, E. (1938) · Journal of the American Chemical Society · doi:10.1021/ja01269a023 · Cited by 28,156
Amine Scrubbing for CO 2 Capture
Rochelle, G. T. (2009) · Science · doi:10.1126/science.1176731 · Cited by 4,440
Anomalous Increase in Carbon Capacitance at Pore Sizes Less Than 1 Nanometer
Chmiola, J., Yushin, G., Gogotsi, Y., Portet, C., Simon, P., & Taberna, P. L. (2006) · Science · doi:10.1126/science.1132195 · Cited by 4,022
Self-citationRecommendations for the characterization of porous solids (Technical Report)
Rouquerol, J., Avnir, D., Fairbridge, C. W., Everett, D. H., Haynes, J. M., Pernicone, N., Ramsay, J. D. F., Sing, K. S. W., & Unger, K. K. (1994) · Pure and Applied Chemistry · doi:10.1351/pac199466081739 · Cited by 3,984
Adsorbent Materials for Carbon Dioxide Capture from Large Anthropogenic Point Sources
Choi, S., Drese, J. H., & Jones, C. W. (2009) · ChemSusChem · doi:10.1002/cssc.200900036 · Cited by 2,596
Caskey, S. R., Wong-Foy, A. G., & Matzger, A. J. (2008) · Journal of the American Chemical Society · doi:10.1021/ja8036096 · Cited by 1,815
Is the bet equation applicable to microporous adsorbents?
(2007) · Studies in Surface Science and Catalysis · doi:10.1016/s0167-2991(07)80008-5 · Cited by 1,147
The reaction of CO2 with ethanolamines
Danckwerts, P. V. (1979) · Chemical Engineering Science · doi:10.1016/0009-2509(79)85087-3 · Cited by 1,116
Yazaydın, A. Ö., Snurr, R. Q., Park, T.-H., Koh, K., Liu, J., LeVan, M. D., Benin, A. I., Jakubczak, P., Lanuza, M., Galloway, D. B., et al. (2009) · Journal of the American Chemical Society · doi:10.1021/ja9057234 · Cited by 907
Dietzel, P. D. C., Besikiotis, V., & Blom, R. (2009) · Journal of Materials Chemistry · doi:10.1039/b911242a · Cited by 689
Cited by
Items 401–500 of 679
Zaman, A. C., & Karaaslan, O. F. (2021) · Materials Chemistry and Physics · doi:10.1016/j.matchemphys.2021.125288 · Cited by 29
Quasielastic neutron scattering study of water confined in carbon nanopores
Chathoth, S. M., Mamontov, E., Kolesnikov, A. I., Gogotsi, Y. G., & Wesolowski, D. J. (2011) · Europhysics Letters (EPL) · doi:10.1209/0295-5075/95/56001 · Cited by 27
Self-citationPotential of Silicon Carbide-Derived Carbon for Carbon Capture
Bhatia, S. K., & Nguyen, T. X. (2011) · Industrial & Engineering Chemistry Research · doi:10.1021/ie201094d · Cited by 27
Grau-Marín, D., Silvestre‐Albero, J., Jardim, E. D. O., Jagiełło, J., Betz, W. R., & Peña, L. E. (2019) · Carbon · doi:10.1016/j.carbon.2019.10.035 · Cited by 27
Cheng, X., Qie, Z., Xiang, H., Liu, Z., Zong, L., He, W., Pi, X., Alhassawi, H., Cao, P., Yang, G., et al. (2025) · Scientific Reports · doi:10.1038/s41598-025-13430-4 · Cited by 26
Aggarwal, P., Umar, F., & Paul, A. (2025) · ACS Applied Nano Materials · doi:10.1021/acsanm.5c03047 · Cited by 27
Utilizing transient breakthroughs for evaluating the potential of Kureha carbon for CO2 capture
Yu, H., Wang, X., Xu, C., Chen, D., Zhu, W., & Krishna, R. (2015) · Chemical Engineering Journal · doi:10.1016/j.cej.2015.01.091 · Cited by 28
Sanz-Pérez, E. S., Arencibia, A., Sanz, R., & Calleja, G. (2015) · RSC Advances · doi:10.1039/c5ra19105j · Cited by 28
Fundamentals in CO2 capture of Na2CO3 under a moist condition
Luo, H., & Kanoh, H. (2017) · Journal of Energy Chemistry · doi:10.1016/j.jechem.2017.08.005 · Cited by 26
Fabrication of Hierarchical N-doped Carbon Nanotubes for CO2 Adsorption
Wang, H., Xu, C., Zhou, Y., Zhao, W., Zhong, J., Huang, W., & Chen, R. (2019) · NANO · doi:10.1142/s1793292019500723 · Cited by 26
Facile synthesis of microporous carbon xerogels for highly selective CO2 adsorption
Wang, S., Xu, Y., Miao, J., Liu, M., Ren, B., Zhang, L., & Liu, Z. (2020) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2020.120023 · Cited by 27
Biochar Lifecycle Contribution to Carbon Neutrality: Key Factors and Regulatory Mechanisms
Yu, A., Yu, J., Pang, Y., Tang, J., Wang, J., Wu, N., & Tang, L. (2025) · Environmental Science & Technology · doi:10.1021/acs.est.5c07816 · Cited by 27
Yao, P., Zhang, J., Qiu, Y., Zheng, Q., Zhang, H., Yan, J., & Li, X. (2021) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.1c00743 · Cited by 27
The influence of the synthesis pH on the morphology and adsorption properties of carbon spheres
Sobczuk, K. S., Pełech, I., Narkiewicz, U., Staciwa, P., Sibera, D., & Moszyński, D. (2022) · Applied Surface Science · doi:10.1016/j.apsusc.2022.155196 · Cited by 25
Liu, Z., Du, Z., Xing, W., & Yan, Z. (2013) · Materials Letters · doi:10.1016/j.matlet.2013.12.021 · Cited by 25
Oschatz, M., Zeiger, M., Jäckel, N., Strubel, P., Borchardt, L., Reinhold, R., Nickel, W., Eckert, J., Presser, V., & Kaskel, S. (2015) · Journal of Materials Chemistry A · doi:10.1039/c5ta03730a · Cited by 25
Self-citationXiao, Q., Wen, J., Guo, Y., Hu, J., Wang, J., Zhang, F., Tu, G., Zhong, Y., & Zhu, W. (2016) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.6b03494 · Cited by 25
Arif, A. F., Kobayashi, Y., Schneider, E. M., Hess, S. C., Balgis, R., Izawa, T., Iwasaki, H., Taniguchi, S., Ogi, T., Okuyama, K., et al. (2017) · Langmuir · doi:10.1021/acs.langmuir.7b01353 · Cited by 25
Primary amine modulated synthesis of two-dimensional porous nanocarbons with tunable ultramicropores
Zhang, L., Li, W., Tang, L., Wang, Q., Hu, Q., Zhang, Y., & Lu, A. (2018) · Journal of Materials Chemistry A · doi:10.1039/c8ta09545k · Cited by 25
Li, M., Liu, J., Deng, S., Liu, Q., Qi, N., & Chen, Z. (2021) · ACS Applied Energy Materials · doi:10.1021/acsaem.1c01297 · Cited by 28
Chen, H., Guo, Y., Zhou, K. C., Wang, J., Zeng, Z., & Li, L. (2023) · Separation and Purification Technology · doi:10.1016/j.seppur.2023.123993 · Cited by 25
CO2 adsorption on crystalline graphitic nanostructures
Casco, M. E., Morelos‐Gómez, A., Vega-Díaz, S. M., Cruz‐Silva, R., Tristán-López, F., Muramatsu, H., Hayashi, T., Escandell, M. M., Terrones, M., Endo, M., et al. (2014) · Journal of CO2 Utilization · doi:10.1016/j.jcou.2014.01.001 · Cited by 24
On the Gas Storage Properties of 3D Porous Carbons Derived from Hyper-Crosslinked Polymers
Gatti, G., Errahali, M., Tei, L., Cossi, M., & Marchese, L. (2019) · Polymers · doi:10.3390/polym11040588 · Cited by 23
Liu, X., Liu, J., Sun, C., Liu, H., Wang, W., Smith, E. F., Jiang, L., Chen, X., & Snape, C. E. (2020) · Journal of Materials Chemistry A · doi:10.1039/d0ta01417f · Cited by 25
Varghese, S. M., Chowdhury, A. R., Arnepalli, D. N., & Gangavarapu, R. R. (2023) · Carbon Trends · doi:10.1016/j.cartre.2023.100250 · Cited by 23
Zhang, Z., Zhang, L., Gao, Q., Sun, N., & Wei, W. (2023) · Journal of CO2 Utilization · doi:10.1016/j.jcou.2023.102570 · Cited by 23
Jin, Z., Xu, Y., Sun, Q., & Lu, A. (2015) · Small · doi:10.1002/smll.201501692 · Cited by 23
Importance of Micropore–Mesopore Interfaces in Carbon Dioxide Capture by Carbon‐Based Materials
Durá, G., Budarin, V. L., Castro‐Osma, J. A., Shuttleworth, P. S., Quek, S. C. Z., Clark, J. H., & NORTH, M. J. (2016) · Angewandte Chemie · doi:10.1002/ange.201602226 · Cited by 23
Recent advances for CO2 mineralization in biochar-amended cementitious composites
Roy, S., Sreenivasan, H., Sarmah, A. K., Baniasadi, H., & Bordoloi, S. (2025) · Resources Conservation and Recycling · doi:10.1016/j.resconrec.2025.108141 · Cited by 28
Burrow, J. N., Eichler, J. E., Wang, Y., Calabro, D. C., & Mullins, C. B. (2022) · Journal of Materials Chemistry A · doi:10.1039/d2ta05911h · Cited by 25
Agar‐Derived Nitrogen‐Doped Porous Carbon for CO 2 Adsorption
Xu, J., Cui, H., Shi, J., Yan, N., Liu, Y., & Li, D. (2018) · ChemistrySelect · doi:10.1002/slct.201802031 · Cited by 22
Carbon beads with a well-defined pore structure derived from ion-exchange resin beads
He, P., Haw, K., Yan, S., Tang, L., Fang, Q., Qiu, S., & Valtchev, V. (2019) · Journal of Materials Chemistry A · doi:10.1039/c9ta04069b · Cited by 22
Hierarchical porous polystyrene-based activated carbon spheres for CO2 capture
Ren, X., Zhang, C., Kou, L., Wang, R., Wang, Y., & Li, R. (2021) · Environmental Science and Pollution Research · doi:10.1007/s11356-021-16561-z · Cited by 22
Rensch, T., Chantrain, V., Sander, M., Grätz, S., & Borchardt, L. (2022) · ChemSusChem · doi:10.1002/cssc.202200651 · Cited by 22
Kwac, K., Lee, J. H., Choi, J. W., & Jung, Y. (2016) · The Journal of Physical Chemistry C · doi:10.1021/acs.jpcc.5b12404 · Cited by 22
Adsorption of carbon dioxide on TEPA-modified TiO 2 /titanate composite nanorods
Kapica‐Kozar, J., Michalkiewicz, B., Wróbel, R. J., Mozia, S. H., Piróg, E., Kusiak‐Nejman, E., Serafin, J., Morawski, A. W., & Narkiewicz, U. (2017) · New Journal of Chemistry · doi:10.1039/c7nj01549f · Cited by 22
Wang, J., Yin, Y., Liu, X., Liu, Y., Xiao, Q., Zhao, L., Demir, M., Şimşek, U. B., Wang, L., & Hu, X. (2026) · Langmuir · doi:10.1021/acs.langmuir.5c05574 · Cited by 21
Extension of Kelvin equation to CO 2 adsorption in activated carbon
Yin, G., Liu, Q., Liu, Z., & Wu, W. (2018) · Fuel Processing Technology · doi:10.1016/j.fuproc.2018.02.006 · Cited by 21
Zheng, L., Li, W. B., & Chen, J. (2018) · RSC Advances · doi:10.1039/c8ra04367a · Cited by 21
Ghimire, P. P., Dassanayake, A. C., Wickramaratne, N. P., & Jaroniec, M. (2019) · Journal of Colloid and Interface Science · doi:10.1016/j.jcis.2019.04.059 · Cited by 21
Lin, W., Cai, Z., Lv, X., Xiao, Q., Chen, K., Li, H., & Wang, C. (2019) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.9b02872 · Cited by 21
Shi, W., Zhang, Q., Liu, S., Su, S., Chang, B., & Yang, B. (2021) · Journal of Colloid and Interface Science · doi:10.1016/j.jcis.2021.04.146 · Cited by 21
Ding, J., Xue, H., Xiao, R., Xu, Y., Song, L., Gong, H. R., Fan, X., Chang, K., Huang, X., Wang, T., et al. (2022) · Nanoscale · doi:10.1039/d1nr08354f · Cited by 21
Wu, D., Li, Z., Zhong, M., Kowalewski, T., & Matyjaszewski, K. A. (2014) · Angewandte Chemie · doi:10.1002/ange.201309836 · Cited by 21
Reljic, S., Escandell, M. M., & Silvestre‐Albero, J. (2022) · C – Journal of Carbon Research · doi:10.3390/c8030041 · Cited by 21
Wang, M., Fu, J., Zhu, J., Yan, Y. P., & Xu, Q. J. (2015) · RSC Advances · doi:10.1039/c5ra02823j · Cited by 22
CO 2 Capture Using Nitrogen-Doped Porous Carbons Derived from Waste Printed Circuit Boards
Liu, Y., Zhang, J., Lin, S., Shimizu, G. K. H., & Sundararaj, U. (2024) · ACS Sustainable Resource Management · doi:10.1021/acssusresmgt.4c00417 · Cited by 22
Fu, N., Yu, J., Liu, R., Wang, X., & Yang, Z. (2019) · Journal of Colloid and Interface Science · doi:10.1016/j.jcis.2019.12.127 · Cited by 20
Nanocast nitrogen-containing ordered mesoporous carbons from glucosamine for selective CO2 capture
Maruccia, E., Lourenço, M. A. O., Priamushko, T., Bartoli, M., Bocchini, S., Pirri, C. F., Saracco, G., Kleitz, F., & Gerbaldi, C. (2021) · Materials Today Sustainability · doi:10.1016/j.mtsust.2021.100089 · Cited by 20
Hu, M., Liu, J., Kong, J., Jia, P., Qi, N., Wu, Y., Chen, Z., Xu, S. N., & Li, N. (2022) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2022.111770 · Cited by 20
Wu, R., Hang, Y., Li, J., & Bao, A. (2022) · Surface and Interface Analysis · doi:10.1002/sia.7101 · Cited by 21
“Presser et al.29 studied the influence of the pore size of microporous carbon on CO2 absorption and proved that the average pore diameter and total pore volume are not the decisive factors for the absorption of CO2 by the microporous carbon adsorbent, and the pore volume of micropores less than 1 nm is the key to the…”
BackgroundScalable preparation of nitrogen-enriched carbon microspheres for efficient CO 2 capture
Wang, M., Wang, J., Qiao, W., Ling, L., & Long, D. (2014) · RSC Advances · doi:10.1039/c4ra11647j · Cited by 20
Zhou, J. P., Wang, X., & Xing, W. (2018) · Royal Society of Chemistry eBooks · doi:10.1039/9781788013352-00001 · Cited by 29
Pei, C., Ben, T., Guo, H. J., Xu, J., Deng, F., Xiang, Z., Cao, D., & Qiu, S. (2013) · Philosophical Transactions of the Royal Society A Mathematical Physical and Engineering Sciences · doi:10.1098/rsta.2012.0312 · Cited by 20
“(iii) Low-pressure carbon dioxide storage in JUC-Z4 and JUC-Z5 Recently, reports revealed that a suitable pore size less than 1 nm was preferred to be sufficiently commensurate with the kinetic diameter of a CO2 molecule in the case of CO2 capture at ambient condition [34].”
BackgroundThermal and Electrical Conductivity of Amorphous and Graphitized Carbide‐Derived Carbon Monoliths
Kern, A. M., Zierath, B., Haertlé, J., Fey, T., & Etzold, B. J. M. (2016) · Chemical Engineering & Technology · doi:10.1002/ceat.201600011 · Cited by 20
Dyjak, S., Kiciński, W., Norek, M., Dyjak, M., & Cudziło, S. (2018) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2018.06.037 · Cited by 20
Khodabakhshi, S., Taddei, M., Rudd, J. A., McPherson, M. J., Niu, Y., Palmer, R. E., Barron, A. R., & Andreoli, E. (2020) · Carbon · doi:10.1016/j.carbon.2020.11.080 · Cited by 20
Hao, W., Björnerbäck, F., Trushkina, Y., Bengoechea, M. O., Salazar‐Alvarez, G., Barth, T., & Hedin, N. (2017) · Energy Procedia · doi:10.1016/j.egypro.2017.08.033 · Cited by 20
RetractedComparative Analysis of CO2 Adsorption Performance of Bamboo and Orange Peel Biochars
Kwon, C. W., Tae, S., & Mandal, S. (2025) · Molecules · doi:10.3390/molecules30071607 · Cited by 20
Jin, Y., Lin, H., Liu, Y., An, H., & Lee, J. S. (2025) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2025.115782 · Cited by 20
Jha, R. K., Bhunia, H., & Basu, S. (2023) · Chemical Engineering Science · doi:10.1016/j.ces.2023.119572 · Cited by 19
Hierarchical porous carbon beads for selective CO2 capture
Jung, S.-Y., Lee, J.-R., Won, Y., Lee, D., Park, Y. C., Bae, Y., & Kim, H. (2021) · Journal of CO2 Utilization · doi:10.1016/j.jcou.2021.101659 · Cited by 19
The Application of Hollow Carbon Nanofibers Prepared by Electrospinning to Carbon Dioxide Capture
Chiang, Y., Chin, W.-T., & Huang, C.-C. (2021) · Polymers · doi:10.3390/polym13193275 · Cited by 19
Synthesis and characterization of activated carbon from Delonix regia seeds for CO2 adsorption
Bhatta, L. K. G., Venkatesh, K., Kiran, N., Gundanna, S. K., & Bhatta, U. M. (2021) · Energy and Climate Change · doi:10.1016/j.egycc.2021.100064 · Cited by 19
Li, J., Kossmann, J., Zeng, K., Zhang, K., Wang, B., Weinberger, C., Antonietti, M., Odziomek, M., & López‐Salas, N. (2023) · Angewandte Chemie · doi:10.1002/ange.202217808 · Cited by 24
Sun, J., Yan, W., Liu, X., Tao, H., Xiong, Y., Tian, S., Feng, J., Huang, Z., & Zhao, Z. (2024) · Chemical Engineering Journal · doi:10.1016/j.cej.2024.151583 · Cited by 18
Alhwaige, A. A., Ishida, H., & Qutubuddin, S. (2024) · ACS Applied Engineering Materials · doi:10.1021/acsaenm.4c00232 · Cited by 19
Liu, Y., Chen, Y., Tian, L., & Hu, R. (2016) · Journal of Porous Materials · doi:10.1007/s10934-016-0294-9 · Cited by 19
Jiang, Y., Tan, P., Qi, S., Liu, X., Yan, J., Fan, F., & Sun, L. (2019) · Angewandte Chemie · doi:10.1002/ange.201900141 · Cited by 18
Płatek‐Mielczarek, A., Conder, J., Fic, K., & Ghimbeu, C. M. (2022) · Journal of Power Sources · doi:10.1016/j.jpowsour.2022.231714 · Cited by 18
Zhang, F., Liu, B., Ni, Z., Zhang, X., Shao, Y., Zhang, F., Sun, K., Fan, R., & Jia, D. (2022) · Carbon · doi:10.1016/j.carbon.2022.08.057 · Cited by 18
Zhang, L., Li, W., Liu, H. S., Wang, Q., Tang, L., Hu, Q., Xu, W., Qiao, W., Lu, Z., & Lu, A. (2018) · Angewandte Chemie · doi:10.1002/ange.201712913 · Cited by 18
Sultana, A. I., Chambers, C., Ahmed, M. M. N., Pathirathna, P., & Reza, T. (2022) · Nanomaterials · doi:10.3390/nano12203575 · Cited by 17
“[71] derived positive correlation (R2 of 0.”
BackgroundResearch progress on the preparation of bamboo-based activated carbon for CO2 adsorption
Wang, B., Xie, Q., Sha, Y.-T., Liu, J., & Liang, D.-C. (2025) · New Carbon Materials · doi:10.1016/s1872-5805(25)60956-5 · Cited by 18
Oschatz, M., & Walczak, R. (2018) · C – Journal of Carbon Research · doi:10.3390/c4040056 · Cited by 17
“researched in many fields such as selective gas capture [75], gas storage [65,140], ion adsorption”
BackgroundCO2 Capture over Activated Carbon Derived from Pulverized Semi-Coke
Jing, J., Zhao, Z., Zhang, X., Feng, J., & Li, W. (2022) · Separations · doi:10.3390/separations9070174 · Cited by 17
“33 nm; when the pore size of adsorbent was 2–3 times the molecular kinetic diameter of CO2, the adsorbent presented good CO2 sorption performance [34].”
BackgroundShi, W., Zhao, Z., Jiang, A., Yukun, M., Yan, Y., Yang, B., & Chang, B. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.110636 · Cited by 17
Toward Tailoring Metal–Organic Frameworks for Photocatalytic Reduction of CO2 to Fuels
Chang, X.-L., Yan, T., & Pan, W. (2024) · Crystal Growth & Design · doi:10.1021/acs.cgd.3c01293 · Cited by 19
Bai, Y., Li, Y., Li, M., Lin, X., Cai, C., He, H., & Liu, S. (2024) · Industrial Crops and Products · doi:10.1016/j.indcrop.2024.119183 · Cited by 17
Reljic, S., Broto‐Ribas, A., Collados, C. C., Jardim, E. D. O., Maspoch, D., Imaz, I., & Silvestre‐Albero, J. (2020) · Chemistry - A European Journal · doi:10.1002/chem.202002473 · Cited by 17
Li, H., Li, C., Budarin, V. L., Clark, J. H., NORTH, M. J., Wang, J., & Wu, X. (2022) · Green Chemistry · doi:10.1039/d1gc03715c · Cited by 17
Liu, Z., Zhu, Y., Du, Z., Xing, W., Komarneni, S., & Yan, Z. (2015) · Journal of Porous Materials · doi:10.1007/s10934-015-0065-z · Cited by 18
Utilization of spent dregs for the production of activated carbon for CO2 adsorption
Serafin, J. (2017) · Green Sciences · doi:10.1515/pjct-2017-0026 · Cited by 17
CO2 Capture Performance of Na2CO3/γ-Al2O3 Sorbent Modified with Organic Acid
Xu, Z., Ma, J., Chen, X., Wang, C., Tao, Z., Liu, D., & Liang, C. (2024) · Energy & Fuels · doi:10.1021/acs.energyfuels.4c00402 · Cited by 16
Zhao, J., Zhang, S., Zhang, X., Zhou, W., Zhao, Q. L., Wu, F., & Xing, B. (2024) · The Science of The Total Environment · doi:10.1016/j.scitotenv.2024.173471 · Cited by 16
Facile Synthesis of Nitrogen-doped Porous Carbon for Selective CO2 Capture
He, J., To, J. W. F., Mei, J., Bao, Z., & Wilcox, J. L. (2014) · Energy Procedia · doi:10.1016/j.egypro.2014.11.233 · Cited by 16
“It is worth noting that the ultramicropores play an important role in CO2 capture as they largely correspond with the CO2 adsorption capacity in carbon materials [9-11].”
BackgroundShi, X., Gong, J., Kierzek, K., Michalkiewicz, B., Zhang, S., Chu, P. K.-H., Chen, X., Tang, T., & Mijowska, E. (2019) · New Journal of Chemistry · doi:10.1039/c9nj01542f · Cited by 16
Hydrogen and carbon dioxide uptake on scalable and inexpensive microporous carbon foams
Kusdhany, M. I. M., Ma, Z., Mufundirwa, A., Li, H., Sasaki, K., Hayashi, A., & Lyth, S. M. (2022) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2022.112141 · Cited by 16
Development of composite activated carbon from mango and almond seed shells for CO2 capture
Aimikhe, V. J., Anyebe, M. S., & Ibezim-Ezeani, M. U. (2022) · Biomass Conversion and Biorefinery · doi:10.1007/s13399-022-03665-w · Cited by 17
“Notably, adsorbents with the maximum specific surface area or pore volume do not necessarily result in maximum CO 2 adsorption [68].”
Yalçınkaya, T. T., Çay, A., Akduman, Ç., Kumbasar, E. P. A., & Yanık, J. (2024) · Journal of Applied Polymer Science · doi:10.1002/app.55475 · Cited by 15
Xie, X., Meng, S., Gan, F., Dai, Z., He, J., Chang, Y., Jiang, X., & Jin, Z. (2024) · Applied Energy · doi:10.1016/j.apenergy.2024.124327 · Cited by 15
Carbon Dioxide Adsorption over Activated Biocarbons Derived from Lemon Peel
Kiełbasa, K., Siemak, J., Sreńscek-Nazzal, J., Bestani, B., Roy, B., & Michalkiewicz, B. (2024) · Molecules · doi:10.3390/molecules29174183 · Cited by 15
ZnO/Carbon Spheres with Excellent Regenerability for Post-Combustion CO2 Capture
Pełech, I., Sibera, D., Staciwa, P., Kusiak‐Nejman, E., Kapica‐Kozar, J., Wanag, A., Narkiewicz, U., & Morawski, A. W. (2021) · Materials · doi:10.3390/ma14216478 · Cited by 15
Tunable and selective formation of micropores and mesopores in carbide-derived carbon
Seo, M. S., Kim, J. H., Kim, J., Han, J., Kang, S., Ihm, J., & Kim, D. O. (2013) · Carbon · doi:10.1016/j.carbon.2013.04.041 · Cited by 15
Impact on CO2 Uptake of MWCNT after Acid Treatment Study
Zgrzebnicki, M., Krauze, N., Gęsikiewicz-Puchalska, A., Kapica‐Kozar, J., Piróg, E., Jędrzejewska, A., Michalkiewicz, B., Narkiewicz, U., Morawski, A. W., & Wróbel, R. J. (2017) · Journal of Nanomaterials · doi:10.1155/2017/7359591 · Cited by 15
“8 nm, are crucial for the CO2 sorption capacity, due to accessibility of those pores for carbon dioxide particles [34].”
BackgroundGyroidal Porous Carbon Activated with NH3 or CO2 as Lithium−Sulfur Battery Cathodes
Krüner, B., Dörr, T. S., Shim, H., Sann, J., Janek, J., & Presser, V. (2018) · Batteries & Supercaps · doi:10.1002/batt.201800013 · Cited by 15
Self-citationLiang, L., Zhou, M., Tan, C., Tian, X., & Li, K. (2018) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2018.05.050 · Cited by 15
Pressureless and Low-Pressure Synthesis of Microporous Carbon Spheres Applied to CO2 Adsorption
Pełech, I., Sibera, D., Staciwa, P., Narkiewicz, U., & Cormia, R. D. (2020) · Molecules · doi:10.3390/molecules25225328 · Cited by 15
Nanoporous Carbons with Tuned Porosity
Ania, C. O., & Raymundo‐Piñero, E. (2019) · Green energy and technology · doi:10.1007/978-981-13-3504-4_5 · Cited by 16
“It has been reported from one side that a heat treatment under H2 at temperatures around 200-600°C is effective for opening the clogged pores and to increase the pore volume and from the other, a chemical or physical activation can be performed over the CDC for increasing the pore volume and specific surface area [182…”
BackgroundEtzi, M., Sartoretti, E., Bensaid, S., Allione, M., Ferraris, S., Castellino, M., & Armandi, M. (2025) · Chemical Engineering Journal · doi:10.1016/j.cej.2025.167166 · Cited by 14
Metadata
- Authors
- Presser, V., McDonough, J., Yeon, S.-H., & Gogotsi, Y.
- Affiliations
- Drexel University (US)
- Korea Institute of Energy Research (KR)
- Corresponding author
- Gogotsi, Yury
- Venue
- Energy & Environmental Science
- Publisher
- Royal Society of Chemistry (RSC)
- Published
- 2011
- Volume
- 4
- Issue
- 8
- Pages
- 3059
- ISSN
- 1754-5692 (ISSN-L)
- 1754-5706
- OpenAlex
- W2170455260
- Cited by
- 668
- References
- 38
- Citations by year
- 2026: 36 · 2025: 43 · 2024: 39 · 2023: 42 · 2022: 65 · 2021: 47 · 2020: 43 · 2019: 57 · 2018: 56 · 2017: 57 · 2016: 55 · 2015: 47 · 2014: 35 · 2013: 31 · 2012: 13
- FWCI
- 45.92
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Energy & Environmental Science (publishedVersion)
- Topics
- Physical Sciences › Chemical Engineering › Filtration and Separation › Carbon Dioxide Capture Technologies
- Physical Sciences › Environmental Science › Environmental Engineering › CO2 Sequestration and Geologic Interactions
- Physical Sciences › Chemistry › Physical and Theoretical Chemistry › Adsorption, diffusion, and thermodynamic properties of materials
- Keywords
- carbide-derived carbon, CO2 sorption, pore size, carbon capture and storage, sub-atmospheric pressure, pore volume, micropores, activation, specific surface area, CO2 adsorption capacity
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.