The DOI matches its Crossref record; 56 of the 56 references it cites were found in a registry or an index; none of the 56 sources its claims cite is checked for support yet.
Recent advances in modelling of frost formation for mechanical systems
Open accessAbstract
The physics underlying frost and ice formation has been extensively studied over the past few decades, with significant contributions to our understanding of this phenomenon. These insights have primarily been applied to engineering systems with refrigerated surfaces, such as refrigerators, freezers and heat pumps of various sizes. Despite considerable progress, the dynamic and complex mechanisms governing frost and ice formation remain an active area of research, as competing factors continue to challenge predictive accuracy. The increasing interest from stakeholders in reducing energy consumption and carbon footprints in mechanical systems further underscores the importance of advancing modelling and simulation capabilities in this domain. This article critically reviews recent advances in frost and ice formation modelling, with a focus on identifying key research gaps and opportunities for further exploration. This article is part of the theme issue ‘Heat and mass transfer in frost and ice’.
Overview
CoChat Summary
TL;DR
This review surveys three decades of frost-growth modelling for mechanical systems, covering physics-based, data-driven, and geometry/surface-treatment approaches. It finds that despite progress, models remain condition-specific, frost density prediction lags thickness prediction, and generic validated models are still lacking.
Key findings
- The review identifies persistent gaps: lack of generic widely applicable models/correlations, need for real-time validation of frost thickness and density, uneven frosting at ultra-low temperatures, and later-stage mechanisms; it states that Song & Dang’s 2018 gaps remain valid.
- Physics-based modelling advanced from Tao et al.’s two-period porous-media model, which introduced an effective mass diffusivity up to seven times the molecular diffusivity of water vapour in air, to air–frost full-domain CFD models that remain sensitive to mesh and empirical correlations.
- Data-driven models report high accuracy within limited ranges: Tahavvor’s ANN/fractal model agreed within 2% for frost density and 5% for frost thickness; Moradkhani et al. used 249 thickness and 54 density data points (80/20 train/test) and reported AAREs of 1.06% for thickness and 0.83% for density, with >99% of predictions within ±10%.
- Surface and geometry studies show effects such as about 10% shorter defrosting with superhydrophobic VMFE coatings, and CFRP fin frost thickness increases of 71.5% and 75.9% when surface temperature decreased from −10°C to −20°C at ambient 5°C and 10°C; generally frost thickness increases with higher air velocity, higher relative humidity, and lower cold surface temperature, while frost density increases with higher wall temperature and air velocity, with relative-humidity impact debatable.
Methods
- Design: critical/narrative review of frost-growth modelling methodologies for mechanical systems over the last three decades, organized into physics-based models, data-driven models, and geometric/surface characterizations.
- Data or sample: reviews representative experimental, analytical, numerical CFD, and machine-learning studies and correlations from the 1940s onward; no new experiments or primary data are collected.
- Main analysis: qualitative synthesis and comparison of model formulations, validation ranges, reported errors, and research gaps; no systematic review protocol or meta-analysis is described.
Limitations
- Paper-stated: reviewed models lack generic applicability; real-time validation of frost thickness/density is needed; data are limited at ultra-low temperatures and later frost stages; high-fidelity air–frost models face moving-boundary/mushy-zone tracking, mesh sensitivity, and extensive computational time; initial frost thickness and density are often guessed and adjusted.
- Paper-stated: data-driven models are limited to available experimental conditions and ranges, e.g. Moradkhani et al. caveat that agreement is limited to forced-convection data, and Abbas et al. report a preliminary correlation capturing 82% of data within a 30% error margin.
- Evident from the text: as a review, it is selective and focuses on mechanical-system applications and basic configurations, explicitly referring readers to other reviews for many experimental works; no systematic search or quantitative synthesis is reported.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures
![Figure 1. Two-period model predicting frost growth [1]: (a) porous-media model describing thermal and mass diffusion within the frost layer during the full growth period; (b) ice column model for initial growth period; (c) transition time between two periods based on simplified empirical observations: moist air temperature, T∞ , humidity ratio, W∞ , velocity, U∞ , heat and mass transfer coefficients, h, hm, cold plate temperature, Tc, ice column temperature, Tβ , ice column diameter, d, frost thickness, δ f , frost density, ρ f, frost effective thermal conductivity, keff and effective mass diffusivity, Deff . Reprinted from [10], with permission from Elsevier.](https://figures.cochat.ai/paper-figures/bc7b9040b27c4acc828ee639caf8c662/recent-advances-in-modelling-of-frost-formation-for-mechanical-systems-figure-1.jpg)
![Figure 2. Three-dimensional visualization of the frost layer at an instant in time with contours of temperature subject to turbulent flow [16,25]. The frost layer thickness varies along x and y. At point D on the frost surface, the thickness is given by Sf^(∗).The plate temperature is held constant at Tp^(∗), but the frost surface temperature varies in x and y. As shown in panel (b), the temperature increases linearly from the plate temperature to the frost surface temperature. The frost density also varies along x and y. However, along the z-direction, only an average frost density value is considered (i.e. no variation along z). Reprinted from [32], with permission from Elsevier.](https://figures.cochat.ai/paper-figures/5daa0df3f18f4c46844e57f67bda267f/recent-advances-in-modelling-of-frost-formation-for-mechanical-systems-figure-2.jpg)
![Figure 3. Frost growth on two parallel cold plates forming a channel airflow is modelled as in a symmetric domain where the airflow cross-section is subject to a finite height and an adiabatic thermal boundary condition at the top [42]. Reprinted from [3], with permission from Elsevier.](https://figures.cochat.ai/paper-figures/21003cd8c727486ab8853ee221600fb6/recent-advances-in-modelling-of-frost-formation-for-mechanical-systems-figure-3.jpg)
![Figure 4. Definition of (a) a square fin and (b) an annular fin, both subject to a cross flow of moist air [44]. Reprinted from [2], with permission from Elsevier.](https://figures.cochat.ai/paper-figures/a78d99ef8fa847eaa9265a2d16a3a390/recent-advances-in-modelling-of-frost-formation-for-mechanical-systems-figure-4.jpg)
![Figure 5. (a) A representative morphology of a micropillar patterned substrate via SEM and a sessile DI water droplet placed on such a substrate, indicating superhydrophobic characteristic [48,53]. (b) Definition of pitch L. Reprinted from [53], with permission from Elsevier.](https://figures.cochat.ai/paper-figures/a9996a6affe7445c8e1ec82759671c4e/recent-advances-in-modelling-of-frost-formation-for-mechanical-systems-figure-5.jpg)
![Figure 6. Three surfaces with different contact angles [49]. Reprinted from Applied Thermal Engineering [54], with permission from Elsevier.](https://figures.cochat.ai/paper-figures/7a9d58799e42480883a3fa91189a322f/recent-advances-in-modelling-of-frost-formation-for-mechanical-systems-figure-6.jpg)
![Figure 7. Frost growth on an AgI stripe patterned surface with (a) three different spacings, and (b) with a comparison between a flat surface and a patterned surface (400 micron metre spacing), showing a horizontal growth trend on strip patterned surface [50]. Reprinted from International Journal of Heat and Mass Transfer [55], with permission from Elsevier.](https://figures.cochat.ai/paper-figures/2385b90487864e14a132560cae09a5ed/recent-advances-in-modelling-of-frost-formation-for-mechanical-systems-figure-7.jpg)
Verification
Claims the paper makes
0 Valid · 8 Not valid · 40 Not checked · 44 Own results and interpretations
In the paper
“The model results compared well with experimental data within the ranges of supersaturation degree (0.0057−0.0090), dimensionless temperature (5.3–8.5) and Nu (29.3–40.6), which corresponded to the experimental relative humidities of 50% and 65%, cold surface temperature of −9 and −5°C, air temperature of 22°C and air velocity of 0.7 m/s-1.”
§ Recent advances in modelling of frost formation for mechanical systems > Physics-based models > Frost domain only models
What the sources say
- Not checked yetcites [20] Hermes CJL. 2012 An analytical solution to the problem of frost growth and densification on flat surfaces. Int. J. Heat Mass Transf. 55, 7346– 7351. (10.1016/j.ijheatmasstransfer.2012.06.070) source
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
In the paper
“This parameter must be guided by empirical correlations of frost density and thickness.”
§ Recent advances in modelling of frost formation for mechanical systems > Physics-based models > Frost domain only models
What the sources say
- Not checked yetcites [27] Negrelli S, Cardoso RP, Hermes CJL. 2016 A finite-volume diffusion-limited aggregation model for predicting the effective thermal conductivity of frost. Int. J. Heat Mass Transf. 101, 1263– 1272. (10.1016/j.ijheatmasstransfer.2016.05.135) source
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
In the paper
“The early growth period is relatively short compared with the overall impact of frost growth to heat and mass transfer by cooling surface, as discussed by Tao et al. [10].”
§ Recent advances in modelling of frost formation for mechanical systems > Physics-based models > Frost domain only models
What the sources say
- Not checked yetcites [10] Tao YX, Besant RW, Rezkallah KS. 1993 A mathematical model for predicting the densification and growth of frost on a flat plate. Int. J. Heat Mass Transf 36, 353– 363. (10.1016/0017-9310(93)80011-I) source
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
In the paper
“Tao et al. [10] developed a mathematical model based on porous media theory to predict the spatial and temporal variations of temperature, frost density and the rate of densification within a frost layer on a flat plate, as well as the time-dependent growth of frost thickness.”
§ Recent advances in modelling of frost formation for mechanical systems > Introduction
What the sources say
- Not checked yetcites [10] Tao YX, Besant RW, Rezkallah KS. 1993 A mathematical model for predicting the densification and growth of frost on a flat plate. Int. J. Heat Mass Transf 36, 353– 363. (10.1016/0017-9310(93)80011-I) source
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
In the paper
“Hermes [20] presented an algebraic first-principles simulation model based on macroscopic heat and mass balances in the frost layer.”
§ Recent advances in modelling of frost formation for mechanical systems > Physics-based models > Frost domain only models
What the sources say
- Not checked yetcites [20] Hermes CJL. 2012 An analytical solution to the problem of frost growth and densification on flat surfaces. Int. J. Heat Mass Transf. 55, 7346– 7351. (10.1016/j.ijheatmasstransfer.2012.06.070) source
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
22 more claims
Create a free account to see all 92 claims and to verify the 56 references still open.
- Probably not a substantial claim. 57
- It may state two separate claims as one. 20
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Recent advances in modelling of frost formation for mechanical systems > Physics-based models > Frost domain only models
“Note: Please see the reference [2] for the following detailed tables in [2]: Table 4 Frost thickness correlations from 1970s to 2010s. Table 5: Frost density correlations from 1970s to 2010s.”
§ Recent advances in modelling of frost formation for mechanical systems > Physics-based models > Frost domain only models
“frost thickness correlations from 1970s to 2010s, frost density correlations from 1970s to 2010s, frost thermal conductivity correlations from 1950s to 2010s, heat transfer coefficient correlations from 1950s to 2010s and mass transfer coefficient correlations from 1970s to 2010s in several tables of reference [11].”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
“About 6 years earlier, Lüer & Beer [48] published their detailed experimental results for the parallel plate configuration and the results from the physics-based model.”
§ Recent advances in modelling of frost formation for mechanical systems > Geometric and surface characterizations > Geometric configuration
Reported 6 · recomputed 16
Citations
Cites
Fox, A. J. (1972) · Journal of the Royal Statistical Society Series B: Statistical Methodology · doi:10.1111/j.2517-6161.1972.tb00912.x · Cited by 756
Ochoa-Tapia, J. A., & Whitaker, S. (1995) · International Journal of Heat and Mass Transfer · doi:10.1016/0017-9310(94)00347-x · Cited by 494
Low Ice Adhesion on Nano-Textured Superhydrophobic Surfaces under Supersaturated Conditions
Bengaluru Subramanyam, S., Kondrashov, V., Rühe, J., & Varanasi, K. K. (2016) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.6b01133 · Cited by 244
New model for frost growth rate
Na, B., & Webb, R. L. (2004) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2003.09.001 · Cited by 212 · cited 1×
“The physics of the model was essentially the same as that in Na et al. [47].”
Review on the measurement and calculation of frost characteristics
Song, M., & Dang, C. (2018) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.03.094 · Cited by 212 · cited 4×
“For more comprehensive, detailed lists, the reader is referred to the footnote of table 1 for the reference to Song and Dance’s work [13].”
InfluentialPrediction of the frost formation on a cold flat surface
Lee, K.-S., Jhee, S., & Yang, D.-K. (2003) · International Journal of Heat and Mass Transfer · doi:10.1016/s0017-9310(03)00195-9 · Cited by 190
A mathematical model for predicting the densification and growth of frost on a flat plate
Tao, Y.-X., Besant, R. W., & Rezkallah, K. S. (1993) · International Journal of Heat and Mass Transfer · doi:10.1016/0017-9310(93)80011-i · Cited by 183
Self-citationMechanisms of ice formation and propagation on superhydrophobic surfaces: A review
Azimi Yancheshme, A., Momen, G., & Jafari Aminabadi, R. (2020) · Advances in Colloid and Interface Science · doi:10.1016/j.cis.2020.102155 · Cited by 168
Dimensionless correlations of frost properties on a cold plate
Yang, D.-K., & Lee, K.-S. (2004) · International Journal of Refrigeration · doi:10.1016/s0140-7007(03)00118-x · Cited by 134
Zhao, Y., Guo, Q., Lin, T., & Cheng, P. (2020) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2020.120074 · Cited by 133
Frosting model for predicting macroscopic and local frost behaviors on a cold plate
Kim, D., Kim, C., & Lee, K.-S. (2015) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2014.11.048 · Cited by 103 · cited 1×
“There are many innovative methods that treat the moving interfacial condition between the frost and air [22– 24 Kim et al. [23] present a three-zone numerical model, which defines air, crust and frost as three discretized zones.”
State-of-the-art review of frost deposition on flat surfaces
Léoni, A., Mondot, M., Durier, F., Revellin, R., & Haberschill, P. (2016) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2016.04.004 · Cited by 103 · cited 5×
“Leoni et al. [11] compare this process with other similar definitions of the overall frost growth process.”
InfluentialAn analytical solution to the problem of frost growth and densification on flat surfaces
Hermes, C. J. L. (2012) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2012.06.070 · Cited by 103
Analysis of the frost growth on a flat plate by simple models of saturation and supersaturation
Lee, Y. B., & Ro, S. T. (2005) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2004.11.001 · Cited by 102 · cited 1×
“There were several studies focusing on supersaturation conditions in the air stream (fogging phenomena) when the frost layer grew [17,18,34,35].”
Transient two-dimensional model of frost formation on a fin-and-tube heat exchanger
Lenic, K., Trp, A., & Frankovic, B. (2009) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2008.06.005 · Cited by 92
Review Article: A Critical Review of Properties and Models for Frost Formation Analysis
Iragorry, J., Tao, Y.-X., & Jia, S. (2004) · HVAC&R Research · doi:10.1080/10789669.2004.10391111 · Cited by 89 · cited 3×
“Such applications include heating, ventilation, air conditioning and refrigeration systems, where frost accumulation on heat exchanger surfaces acts as an insulating layer, hindering heat transfer efficiency and increasing energy consumption [1–4].”
Self-citationA generalized simple model for predicting frost growth on cold flat plate
Wang, W., Guo, Q. C., Lu, W. P., Feng, Y. C., & Na, W. (2012) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2011.10.011 · Cited by 89 · cited 1×
“Wang et al. [26] conducted a similar, lumped model that is applicable across a wide range of frosting conditions, including air temperatures from −8°C to 25°C, cold plate temperatures from −16°C to −4°C, air humidities from 30% to 80%, and air velocities from 0.7 to 5 m/s -1 . a Please see the…”
InfluentialZhao, Y., Wang, R. Z., & Yang, C. (2017) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2016.12.112 · Cited by 78
Frost growth mechanism and its behavior under ultra-low temperature conditions
Jeong, H., Byun, S., Kim, D. R., & Lee, K.-S. (2021) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2021.120941 · Cited by 75 · cited 1×
“The model used a total of 249 data points for frost thickness and 54 data points for frost density from previous studies [7,40], with 80% used for training and 20% for testing using the following correlations for the frost thickness and frost density respectively, using five independent variables.…”
Modeling of frost formation over parallel cold plates considering a two-dimensional growth rate
Armengol, J. M., Salinas, C. T., Xamán, J., & Ismail, K. A. R. (2016) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2016.01.017 · Cited by 69 · cited 4×
“Armengol et al. [29] conducted a study using a two-dimensional approach for the growth rate, allowing frost elements to increase in both height and width.”
InfluentialFrost deposition in a parallel plate channel under laminar flow conditions
Lüer, A., & Beer, H. (2000) · International Journal of Thermal Sciences · doi:10.1016/s1290-0729(00)00193-8 · Cited by 64
Kim, C., Lee, J., & Lee, K.-S. (2017) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2017.07.130 · Cited by 63 · cited 1×
“There are many innovative methods that treat the moving interfacial condition between the frost and air [22– 24 Kim et al. [23] present a three-zone numerical model, which defines air, crust and frost as three discretized zones.”
Modeling of frost formation over parallel cold plates
Ismail, K. A. R., & Salinas, C. S. (1999) · International Journal of Refrigeration · doi:10.1016/s0140-7007(98)00069-3 · Cited by 61
Frost layer growth behavior under cryogenic conditions
Lee, J., Jeong, H., Kim, D. R., & Lee, K.-S. (2019) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2019.114333 · Cited by 60
Dimensionless correlations of frost properties on a cold cylinder surface
Kim, J.-S., Yang, D.-K., & Lee, K.-S. (2008) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2008.01.007 · Cited by 57
Modeling of frost layer growth considering frost porosity
Lee, J., Kim, J., Kim, D. R., & Lee, K.-S. (2018) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.05.098 · Cited by 57
(2022) · doi:10.1016/j.applthermaleng.2022.118416 · Cited by 54
Tahavvor, A. R., & Yaghoubi, M. A. (2010) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2010.06.004 · Cited by 38
Li, F., Wu, S., Ma, Z., Zhao, R., & Huang, D. (2022) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2022.118220 · Cited by 36 · cited 1×
“…could lead to significant impact on the engineering design of a frosting heat exchanger, in which the full growth of frost layer lasts hours before a defrosting cycle kicks in. Li et al. [54] presented a system-level study for an application of vertical-fin microchannel frosting evaporator (VMFE).”
An experimental study on frosting of laminar air flow on a cold surface with local cooling
Kwon, J.-T., Lim, H. J., Kwon, Y.-C., Koyama, S., Kim, D.-H., & Kondou, C. (2006) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2005.12.009 · Cited by 35
Negrelli, S., Cardoso, R. P., & Hermes, C. J. L. (2016) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2016.05.135 · Cited by 34
Moradkhani, M. A., Hosseini, S. H., Valizadeh, M., & Song, M. (2021) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2021.105667 · Cited by 34
Yu, F., Liu, Z., Li, Y., Chen, Y., & Li, Y. (2022) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2022.07.021 · Cited by 34
Moradkhani, M. A., Hosseini, S. H., Shangwen, L., & Song, M. (2022) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2022.119258 · Cited by 33
Chen, G., Deng, X., Zhang, G., & Yan, X. (2019) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.12.133 · Cited by 31 · cited 2×
“One of the representative studies was from Chen et al. [17] in which a fix-grid simulation method was applied by coupling the r o y a l s o c i e t y p u b l i s h i n g . o r g / j o u r n a l / r s t a P h il .”
Heat and mass transfer on a cylinder surface in cross flow under supersaturated frosting conditions
Mago, P. J., & Sherif, S. A. (2003) · International Journal of Refrigeration · doi:10.1016/s0140-7007(03)00076-8 · Cited by 31
Sarmiento, A. P., de Sá Sarmiento, F. I. P., Shooshtari, A., & Ohadi, M. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.123680 · Cited by 29
Fixed grid numerical modelling of frost growth and densification
Bartrons, E., Galione, P., & Segarra, C. D. P. (2018) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.10.080 · Cited by 26
Predictive models on the frost formation for plain surface - a review and comparative study
Li, S., & Wang, C. (2021) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2021.105670 · Cited by 26
A finite volume method to solve the frost growth using dynamic meshes
Bartrons, E., Oliet, C., Gutiérrez, E., Naseri, A., & Pérez-Segarra, C. D. (2018) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.03.104 · Cited by 24
Experimental investigation of frost formation on a horizontal cold cylinder under cross flow
Barzanoni, Y., Noorshams, O., Tabrizi, H. B., & Damangir, E. (2011) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2011.02.011 · Cited by 19
Farzaneh, M., Zgheib, N., Sherif, S. A., & Balachandar, S. (2022) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2022.123233 · Cited by 18
A physics-based model for frost buildup under turbulent flow using direct numerical simulations
Zgheib, N., Farzaneh, M., Balachandar, S., & Sherif, S. A. (2021) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2021.121915 · Cited by 17
Chen, Y., Liu, Z., Li, Y., Yu, F., & Li, Y. (2022) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2021.12.020 · Cited by 15
Modeling of the frost layer’s growth considering its melting and re-solidification
Wang, Z., Han, Z., Liang, Z., Deng, W., & Xu, Z. (2024) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2023.124777 · Cited by 13
Towards the pseudo-2D modeling of frost growth between cold parallel plates
Coulombe, A., Rahal, M., Fellouah, H., & Poncet, S. (2022) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2022.108031 · Cited by 12
Han, J. M., Park, S. H., Park, Y. G., Pandey, S., & Ha, M. Y. (2022) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2022.12.017 · Cited by 12
Okabe, T., Tang, J., Nishimura, K., & Shikazono, N. (2023) · Nanomaterials · doi:10.3390/nano13233035 · Cited by 11
Frost growth on silver iodide (AgI) stripe patterned surface under condensation frosting condition
Tang, J., Okabe, T., Nishimura, K., Ściążko, A., Zhang, H., & Shikazono, N. (2024) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2024.126237 · Cited by 11
Benítez, T., Sherif, S. A., & Benítez, J. (2019) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2019.02.005 · Cited by 9
Abbas, S., & Park, C. W. (2024) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2024.107333 · Cited by 8
Tahavvor, A. R. (2016) · Heat and Mass Transfer · doi:10.1007/s00231-016-1848-8 · Cited by 7
Olejniczak, D., & Nowacki, M. (2020) · Transportation Research Procedia · doi:10.1016/j.trpro.2020.11.005 · Cited by 5
Time acceleration methodology for rapid simulation of frost formation with experimental validation
Kim, D. W., Kwon, T. W., Hwang, H. B., Park, Y. G., Min, J. K., Balachandar, S., & Ha, M. Y. (2024) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2023.124861 · Cited by 5
Xu, X. Y., & Wang, W. (2024) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2024.125612 · Cited by 2
Densification model for ice layer growth on icing surfaces of aircraft
Tao, Y.-X., & Jiang, J. (1999) · 37th Aerospace Sciences Meeting and Exhibit · doi:10.2514/6.1999-98 · Cited by 1
Self-citation
Research works printed but not linked: 2
- Mao Y, Besant R, Rezkallah K. 1992 Measurement and correlations of frost properties with airflow over a flat plate. ASHRAE Trans. Symp 98, 65–78.
- Mao Y, Besant R. 2005 Measurement and correlations of frost properties with laminar airflow at room temperature over a flat plate. ASHRAE Trans. Symp 111, 739–745.
Cited by
Zhang, X., Chen, X., Zhang, G., Yang, Y., & Ni, L. (2026) · Energy · doi:10.1016/j.energy.2026.140524 · Cited by 4
Investigation of Frosting Performance on Air-Sourced Heat Pump Evaporator for Cold Climate
Alsotary, O., & Amano, R. S. (2026) · Journal of energy resources technology. · doi:10.1115/1.4071929
Ji, J., Li, T., Lan, X., & Xie, Y. (2026) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2026.129521
A Framework for Modeling Frost Formation Initiation on Metallic SurfacesPreprint
Ahmed, S. S., Tasmin, N., Ahmed, I., Das, S. T., & Shattique, M. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.7551783
A Framework for Modeling Frost Formation Initiation on Metallic SurfacesPreprint
Ahmed, S. S., Tasmin, N., Ahmed, I., Das, S. T., & Shattique, M. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.7551859
Metadata
- Authors
- Tao, Y.
- Affiliations
- Mechanical Engineering, Cleveland State University
- ORCID
- Tao, Yong
- Venue
- Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Publisher
- The Royal Society
- Published
- 2025-07-17
- Volume
- 383
- Issue
- 2301
- Pages
- 20240369-20240369
- ISSN
- 1364-503X (ISSN-L)
- 1471-2962
- PMC
- PMC12289215
- OpenAlex
- W4412488992
- Semantic Scholar
- eb5eb437ae2d6695f9aff30e1fa9201bb308d621
- Cited by
- 6
- References
- 56
- Citations by year
- 2026: 6
- FWCI
- 0.28
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Licence
- cc-by
- creativecommons.org/licenses/by/4.0/ (vor)
- creativecommons.org/licenses/by/4.0/ (tdm)
- Locations
- Philosophical Transactions of the Royal Society A Mathematical Physical and Engineering Sciences (publishedVersion, cc-by)
- PubMed Central (publishedVersion, cc-by)
- PubMed (publishedVersion)
- EngagedScholarship @ Cleveland State University (Cleveland State University) (submittedVersion, cc-by)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Refrigeration and Air Conditioning Technologies
- Physical Sciences › Engineering › Aerospace Engineering › Icing and De-icing Technologies
- Physical Sciences › Chemical Engineering › Filtration and Separation › Freezing and Crystallization Processes
- Keywords
- frost formation, ice formation, heat pumps, refrigerators, freezers, energy consumption, carbon footprint, heat and mass transfer, prediction accuracy
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-11-18, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-11-18 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.