Compensation Topologies in IPT Systems: Standards, Requirements, Classification, Analysis, Comparison and Application
Open accessThe DOI matches its Crossref record; 85 of the 85 references it cites were found in a registry or an index.
Abstract
Wireless power transfer devices are becoming more relevant and widespread. Therefore, an article is devoted to a review, analysis and comparison of compensation topologies for an inductive power transfer. A new classification of topologies is developed. A lot of attention is paid to the problems of the physical fundamentals of compensation work, standards, safety, and five main topology requirements. It is determined, that topologies with the series primary compensating are the most effective in the IPT for charging devices among the four classical schemes. The series-parallel solution is recommended in case of the low output voltage, minimum size of a secondary side coil is achievable. The series-series solution does not depend on the magnetic coupling coefficient and the load on the resonance frequency. For the convenience of displaying and understanding the information, the comparison results are listed in the tables, graphs and dependencies. The main suitable topologies for a certain application are defined. The given conclusions provide a “one-stop” information source and a selection guide on the application of compensation topologies both in terms of devices and in terms of power level that is the main value of this paper. During literature analysis and recent trends in the market for wireless power transmission devices, the main possible further ways of developing topologies are underlined. First of all, it concerns increasing the frequency of resonance of compensation topologies, the use of multilevel / multi-pulse / multicoils structures, the study of existing high-frequency semiconductors and the development of the semiconductor and magnetic materials.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Greiner, W. (1998) · Theoretical Physics · doi:10.1007/978-1-4612-0587-6 · Cited by 6,657
Wireless Power Transfer via Strongly Coupled Magnetic Resonances
Kurs, A., Karalis, A., Moffatt, R., Joannopoulos, J. D., Fisher, P., & Soljačić, M. (2007) · Science · doi:10.1126/science.1143254 · Cited by 5,576 · cited 3×
“But a real impetus to the development of WPT with compensation was a well-known study in Massachusetts Institute Of Technology (MIT) in 2007 [37].”
BackgroundMethodGUIDELINES FOR LIMITING EXPOSURE TO TIME-VARYING ELECTRIC AND MAGNETIC FIELDS (1 Hz TO 100 kHz)
(2010) · Health Physics · doi:10.1097/hp.0b013e3181f06c86 · Cited by 2,164
Design Considerations for a Contactless Electric Vehicle Battery Charger
Wang, C.-S., Stielau, O. H., & Covic, G. A. (2005) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2005.855672 · Cited by 1,487 · cited 5×
“A smaller primary capacitance is always required for PS topology and the change becomes larger with better coupling or higher secondary quality factor [50].”
BackgroundInfluentialA Critical Review of Recent Progress in Mid-Range Wireless Power Transfer
Hui, S. Y. R., Zhong, W., & Lee, C. K. (2014) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2013.2249670 · Cited by 1,465 · cited 1×
“It is logical to assume that the more coils will be, the more complex the system will be, because the number of mutual inductances and the influence will be proportional to each [123].”
BackgroundWang, C.-S., Covic, G. A., & Stielau, O. H. (2004) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2003.822038 · Cited by 1,213 · cited 9×
“This phenomenon is caused by the input impedance (Zi) that may vary roughly from capacitive to inductive depending on secondary quality factor (Qs) and this may cause unstable operating modes [28] (Fig.”
BackgroundInfluentialA Double-Sided LCC Compensation Network and Its Tuning Method for Wireless Power Transfer
Li, S., Li, W., Deng, J., Nguyen, T. D., & Mi, C. C. (2015) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2014.2347006 · Cited by 1,091 · cited 4×
“The high-order compensation topologies such as the LCC and LCL have become more and more popular due to the better comprehensive performance [100], [102], [108]–[110].”
BackgroundInfluentialCompensation Topologies of High-Power Wireless Power Transfer Systems
Zhang, W., & Mi, C. C. (2016) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2015.2454292 · Cited by 992 · cited 10×
“High efficiency can be achieved by soft switching of semiconductors [10].”
BackgroundInfluentialWireless Power Transfer for Vehicular Applications: Overview and Challenges
Patil, D., McDonough, M. K., Miller, J. M., Fahimi, B., & Balsara, P. T. (2018) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2017.2780627 · Cited by 991 · cited 10×
“In order to protect the driver and passengers in electric vehicles, metal protective screens can be installed [7], [21].”
BackgroundInfluentialWireless Charging Technologies: Fundamentals, Standards, and Network Applications
Lu, X., Wang, P., Niyato, D., Kim, D. I., & Han, Z. (2016) · IEEE Communications Surveys & Tutorials · doi:10.1109/comst.2015.2499783 · Cited by 968 · cited 7×
“A very detailed study of this issue and the abovementioned applications has been conducted [4].”
BackgroundMethodInfluentialCannon, B. L., Hoburg, J. F., Stancil, D. D., & Goldstein, S. C. (2009) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2009.2017195 · Cited by 924 · cited 1×
“sible distance between the coils increases and thus the efficiency of the transferred power decreases less slowly [9].”
BackgroundA Bidirectional Inductive Power Interface for Electric Vehicles in V2G Systems
Madawala, U. K., & Thrimawithana, D. J. (2011) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2011.2114312 · Cited by 813 · cited 1×
“The SIMO is also used for Maglev train with the series compensation on the primary side [130]; for the bidirectional Vehicle-To-Grid (V2G) systems multilevel IPT converters with 3 coils LCL compensation [131] and the load-isolation WPT with the 3-coil SSS compensation [132].”
MethodOptimal Design of ICPT Systems Applied to Electric Vehicle Battery Charge
Sallan, J., Villa, J. L., Llombart, A., & Sanz, J. F. (2009) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2009.2015359 · Cited by 734 · cited 4×
“At low-power levels, where the wire section is not a relevant parameter, PS and PP compensations make it possible working at a slightly larger distance with the same operating frequency [55].”
BackgroundMethodInfluentialLi, H., Li, J., Wang, K., Chen, W., & Yang, X. (2015) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2014.2349534 · Cited by 592 · cited 2×
“The SS compensation is used and intensively investigated at different resonance frequencies from kilohertz [49], [58]–[69] to megahertz [70]–[72], and power from several watts [62], [72], [73] to tens of kilowatts [21], [55], [74].”
BackgroundMethodStability and control of inductivelycoupled power transfer systems
Boys, J. T., Covic, G. A., & Green, A. W. (2000) · IEE Proceedings - Electric Power Applications · doi:10.1049/ip-epa:20000017 · Cited by 559 · cited 2×
“In [28] it is noted, that PP topology has been chosen since it is commonly used for high-power industrial [53].”
BackgroundZhang, W., Wong, S.-C., Tse, C. K., & Chen, Q. (2014) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2013.2249112 · Cited by 505 · cited 1×
“In [10], [68], and [86]–[88] it is pointed that both the SS and SP compensations achieve CC/CV charging by choosing a suitable system operating frequency.”
BackgroundHui, S. Y. R., & Ho, W. W. C. (2005) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2005.846550 · Cited by 501 · cited 1×
“Free-positioning approach can be applied based on the three-layer coil array structure [129].”
MethodA contactless electrical energy transmission system for portable-telephone battery chargers
Jang, Y., & Jovanovic, M. M. (2003) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2003.812472 · Cited by 484
Qu, X., Han, H., Wong, S.-C., Tse, C. K., & Chen, W. (2015) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2015.2396471 · Cited by 474 · cited 1×
“pensation [137]), electric buses, with the description and analytical expressions, the compensation and geometry of coils, efficiency, and others is given [2], [50], [138].”
BackgroundHigh-Misalignment Tolerant Compensation Topology For ICPT Systems
Villa, J. L., Sallan, J., Sanz Osorio, J. F., & Llombart, A. (2012) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2011.2161055 · Cited by 467 · cited 6×
“Total impedance for the four basic topologies [56] and load independent output condition [10].”
BackgroundInfluentialDiekhans, T., & De Doncker, R. W. (2015) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2015.2393912 · Cited by 421 · cited 2×
“can achieve the CV characteristic [97], and the S-S-LCC compensated three-coil WPT system can achieve the CC characteristic.”
BackgroundOverview of wireless power transfer technologies for electric vehicle battery charging
Musavi, F., & Eberle, W. (2014) · IET Power Electronics · doi:10.1049/iet-pel.2013.0047 · Cited by 417 · cited 1×
“pensation [137]), electric buses, with the description and analytical expressions, the compensation and geometry of coils, efficiency, and others is given [2], [50], [138].”
BackgroundBosshard, R., Kolar, J. W., Muhlethaler, J., Stevanovic, I., Wunsch, B., & Canales, F. (2015) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2014.2311302 · Cited by 411
Zhang, W., Wong, S.-C., Tse, C. K., & Chen, Q. (2014) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2013.2273364 · Cited by 406 · cited 4×
“The transfer function for: a)SS topology; b)SP topology [84].”
BackgroundMethodInfluentialComparison Study on SS and Double-Sided LCC Compensation Topologies for EV/PHEV Wireless Chargers
Li, W., Zhao, H., Deng, J., Li, S., & Mi, C. C. (2016) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2015.2479938 · Cited by 375 · cited 3×
“The voltage and current stresses on the series capacitors and main coils of the double-sided LCC compensation topology are smaller than SS compensation topology [106].”
BackgroundMethodInfluentialBerger, A., Agostinelli, M., Vesti, S., Oliver, J. A., Cobos, J. A., & Huemer, M. (2015) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2015.2410216 · Cited by 365 · cited 1×
“The SS compensation is used and intensively investigated at different resonance frequencies from kilohertz [49], [58]–[69] to megahertz [70]–[72], and power from several watts [62], [72], [73] to tens of kilowatts [21], [55], [74].”
MethodGeneral Analysis on the Use of Tesla's Resonators in Domino Forms for Wireless Power Transfer
Zhong, W., Lee, C. K., & Hui, S. Y. R. (2013) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2011.2171176 · Cited by 362 · cited 1×
“The Domino resonator systems are a reproduction of Nikola Tesla’s experiments [152].”
MethodLi, W., Zhao, H., Li, S., Deng, J., Kan, T., & Mi, C. C. (2015) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2014.2384003 · Cited by 331 · cited 3×
“This compensation has the independence of the coupling coefficient and load conditions [100], [101].”
BackgroundKan, T., Nguyen, T.-D., White, J. C., Malhan, R. K., & Mi, C. C. (2017) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2016.2552060 · Cited by 330 · cited 8×
“17c) [11], [81], [105], [77], [98], [99], [147] and other low-power transport devices.”
BackgroundMethodInfluentialDesign of loosely coupled inductive power transfer systems
Stielau, O. H., & Covic, G. A. (2002) · PowerCon 2000. 2000 International Conference on Power System Technology. Proceedings (Cat. No.00EX409) · doi:10.1109/icpst.2000.900036 · Cited by 328
Joun, G. B., & Cho, B. H. (1998) · IEEE Transactions on Power Electronics · doi:10.1109/63.728328 · Cited by 291
Contactless Energy Transfer System With FPGA-Controlled Resonant Converter
Moradewicz, A. J., & Kazmierkowski, M. P. (2010) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2010.2051395 · Cited by 270 · cited 5×
“for a strong magnetic coupling [8], [42], [50].”
BackgroundInfluentialA Comparative Study of Power Supply Architectures in Wireless EV Charging Systems
Esteban, B., Sid-Ahmed, M., & Kar, N. C. (2015) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2015.2440256 · Cited by 256 · cited 1×
“LCL-LCL, LCC-LCC) maintain high efficiency over their full range of coupling and loading [96].”
BackgroundReview of Near-Field Wireless Power and Communication for Biomedical Applications
Kim, H.-J., Hirayama, H., Kim, S., Han, K. J., Zhang, R., & Choi, J.-W. (2017) · IEEE Access · doi:10.1109/access.2017.2757267 · Cited by 252 · cited 1×
“For portable or implantable and biomedical applications in most cases, the SP or SS topology is used commonly [153], [154].”
BackgroundMai, R., Chen, Y., Li, Y., Zhang, Y., Cao, G., & He, Z. Y. (2017) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2017.2654360 · Cited by 249 · cited 3×
“There may be charging stations for charging multiple bicycles at different power levels with the LCL and CLC compensation [98], [99].”
BackgroundLee, S.-H., & Lorenz, R. D. (2011) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2011.2168555 · Cited by 247 · cited 1×
“The compensations with a parallel capacitor on the primary side are rarely used [46], [47] due to the large input impedance, the complexity of the calculations, dependence on the coupling coefficient and load, and other disadvantages.”
BackgroundAnalysis, Design, and Control of a Transcutaneous Power Regulator for Artificial Hearts
Chen, Q., Wong, S. C., Tse, C. K., & Ruan, X. (2009) · IEEE Transactions on Biomedical Circuits and Systems · doi:10.1109/tbcas.2008.2006492 · Cited by 244 · cited 1×
“Preferably these are medical implants [29], [155].”
Power-Factor-Corrected Single-Stage Inductive Charger for Electric Vehicle Batteries
Egan, M. G., O'Sullivan, D. L., Hayes, J. G., Willers, M. J., & Henze, C. P. (2007) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2007.892996 · Cited by 202
Inductive power transfer for electric vehicle charging: Technical challenges and tradeoffs
Bosshard, R., & Kolar, J. W. (2016) · IEEE Power Electronics Magazine · doi:10.1109/mpel.2016.2583839 · Cited by 201 · cited 3×
“In this case, the road surface is fitted with transmission coils, and in the vehicle floor is embedded a receiving coil [21], [57].”
BackgroundMethodInductively coupled power transfer (ICPT) for electric vehicle charging – A review
Kalwar, K. A., Aamir, M., & Mekhilef, S. (2015) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2015.03.040 · Cited by 191 · cited 1×
“ing [145] in view of the benefits described in Section IV.”
BackgroundA Parallel Topology for Inductive Power Transfer Power Supplies
Hao, H., Covic, G. A., & Boys, J. T. (2014) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2013.2262714 · Cited by 190
An Overview of Resonant Circuits for Wireless Power Transfer
Jiang, C., Chau, K. T., Liu, C., & Lee, C. H. T. (2017) · Energies · doi:10.3390/en10070894 · Cited by 186
Comparative Analysis of Two-Coil and Three-Coil Structures for Wireless Power Transfer
Zhang, J., Yuan, X., Wang, C., & He, Y. (2017) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2016.2526780 · Cited by 186 · cited 1×
“advantages of the three-coil system are the maximum energy efficiency, the energy efficiency stiffness against load variations and the reduced EMF emission induced by the coil misalignments [124], [125].”
BackgroundWireless power transfer inspired by the modern trends in electromagnetics
Song, M., Belov, P., & Kapitanova, P. (2017) · Applied Physics Reviews · doi:10.1063/1.4981396 · Cited by 172 · cited 2×
“Some examples of using IPT with a resonant coupling: a) stationary charging for EV [21]; b) wireless dynamic charging of EV (roadway powered) [161]; c) bicycle charger [147]; d) powering multiple wireless devices revealing a practical living room environment [24]; e)mobile charger [158]; f) electric toothbrush charger…”
BackgroundMethodDesign of a Single-Stage Inductive-Power-Transfer Converter for Efficient EV Battery Charging
Huang, Z., Wong, S.-C., & Tse, C. K. (2017) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2016.2631596 · Cited by 171 · cited 1×
“For the wireless charging of electric vehicles for the operation in the current LIO mode, using the SS compensation, and for operation in the voltage LIO mode it is the SP [84], [85].”
MethodAbou Houran, M., Yang, X., & Chen, W. (2018) · Electronics · doi:10.3390/electronics7110296 · Cited by 170
The design of a contact-less energy transfer system for a people mover system
Covic, G. A., Elliott, G., Stielau, O. H., Green, R. M., & Boys, J. T. (2002) · PowerCon 2000. 2000 International Conference on Power System Technology. Proceedings (Cat. No.00EX409) · doi:10.1109/icpst.2000.900035 · Cited by 165 · cited 1×
“In public transport systems [141] the secondary systems are electrically isolated and move along a long track.”
BackgroundA new approach to power supplies for robots
Esser, A., & Skudelny, H.-C. (1991) · IEEE Transactions on Industry Applications · doi:10.1109/28.90341 · Cited by 164 · cited 1×
“In such cases, rotary coils are often used to have more degrees of freedom in the mechanism [42], [149].”
BackgroundLi, Y., Xu, Q., Lin, T., Hu, J., He, Z., & Mai, R. (2018) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2018.2808698 · Cited by 158 · cited 2×
“The double-sided LCC compensation is the most popular as it can reduce the current stress in the inverter, has a high efficiency, high misalignment tolerance and load independence characteristics [11], [101]–[103].”
BackgroundMethodPulse Density Modulated ZVS Full-Bridge Converters for Wireless Power Transfer Systems
Li, H., Wang, K., Fang, J., & Tang, Y. K. (2018) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2018.2812213 · Cited by 154 · cited 1×
“The SS compensation is used and intensively investigated at different resonance frequencies from kilohertz [49], [58]–[69] to megahertz [70]–[72], and power from several watts [62], [72], [73] to tens of kilowatts [21], [55], [74].”
MethodZhang, W., Wong, S., Tse, C. K., & Chen, Q. (2014) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2014.2348558 · Cited by 142
Large air-gap coupler for inductive charger [for electric vehicles]
Sakamoto, H., Harada, K., Washimiya, S., Takehara, K., Matsuo, Y., & Nakao, F. (1999) · IEEE Transactions on Magnetics · doi:10.1109/20.800578 · Cited by 133 · cited 1×
“Initially, mainly purely inductive methods of WPT for charging electric cars were considered [31]–[36].”
MethodChen, Y., Kou, Z., Zhang, Y., He, Z. Y., Mai, R., & Cao, G. (2017) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2017.2782269 · Cited by 126 · cited 3×
“There may be charging stations for charging multiple bicycles at different power levels with the LCL and CLC compensation [98], [99].”
BackgroundComparative evaluation of control methods for Inductive Power Transfer
Bosshard, R., Badstuebner, U., Kolar, J. W., & Stevanović, I. (2012) · International Conference on Renewable Energy Research and Applications (ICRERA) · doi:10.1109/icrera.2012.6477400 · Cited by 120 · cited 1×
“Respectively, at the same time, a larger primary capacity needed [50], [75], [76].”
BackgroundAn Optimized Track Length in Roadway Inductive Power Transfer Systems
Zhang, W., Wong, S., Tse, C. K., & Chen, Q. (2014) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2014.2301460 · Cited by 114 · cited 2×
“it requires the current source input to avoid any instantaneous change in the voltage [51].”
BackgroundFu, M., Tang, Z., & Ma, C. (2018) · IEEE Transactions on Industrial Informatics · doi:10.1109/tii.2018.2833209 · Cited by 102 · cited 3×
“the parallel compensation, SP or PP [52].”
BackgroundInfluentialSliding transformers for linear contactless power delivery
Barnard, J. M., Ferreira, J. A., & van Wyk, J. D. (1997) · IEEE Transactions on Industrial Electronics · doi:10.1109/41.649938 · Cited by 91 · cited 2×
“The important advantages of the S-compensation include less component count and the complexity of the WPT system with an increased power transfer capability and less distortion on the primary current compared with the SS topology.”
MethodHou, J., Chen, Q., Ren, X., Ruan, X., Wong, S., & Tse, C. K. (2014) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2014.2320524 · Cited by 88 · cited 2×
“The S/SP type compensation can realize a good output stability and low circulating losses under the condition of wide parameters variations [117].”
BackgroundMultiple Output Inductive Charger for Electric Vehicles
Vu, V.-B., Phan, V.-T., Dahidah, M., & Pickert, V. (2018) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2018.2882945 · Cited by 82 · cited 2×
“topologies and may reach efficiency more than 95% [19], [121], [122].”
BackgroundMethodOuyang, Z., Sen, G., Thomsen, O. C., & Andersen, M. A. E. (2012) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2012.2186777 · Cited by 81
Contactless inductive power pickup system for Maglev applications
Song, B.-M., Kratz, R., & Gurol, S. (2003) · IEEE Industry Applications Society Annual Meeting (IAS) · doi:10.1109/ias.2002.1043746 · Cited by 67 · cited 2×
“The supply system of Maglev train is developed in [130].”
BackgroundMethodSamanta, S., & Rathore, A. K. (2016) · IET Power Electronics · doi:10.1049/iet-pel.2015.0775 · Cited by 65 · cited 3×
“and inductive methods from renewable energy sources [48] – used the PS topology, [150], [151] - a contactless underwater power delivery.”
BackgroundMethodProbabilistically Robust SWIPT for Secrecy MISOME Systems
Khandaker, M. R. A., Wong, K., Zhang, Y., & Zheng, Z. (2016) · IEEE Transactions on Information Forensics and Security · doi:10.1109/tifs.2016.2611478 · Cited by 61 · cited 2×
“Such systems are used to transmit not only the energy but also information [128].”
BackgroundA 3D Wireless Charging Cylinder With Stable Rotating Magnetic Field for Multi-Load Application
Han, H., Mao, Z., Zhu, Q., Su, M., & Hu, A. P. (2019) · IEEE Access · doi:10.1109/access.2019.2903831 · Cited by 54 · cited 1×
“The MIMO is used for increasing the magnetic communication range [134].”
MethodAdvances in inductively coupled power transfer technology for rail transit
Shi, L., Yin, Z., Jiang, L., & Li, Y. (2017) · CES Transactions on Electrical Machines and Systems · doi:10.23919/tems.2017.8241360 · Cited by 51 · cited 1×
“Speaking about a high power, it can be EVs, buses, trains [136].”
BackgroundA voltage ratio-based efficiency control method for 3 kW wireless power transmission
Ishihara, H., Moritsuka, F., Kudo, H., Obayashi, S., Itakura, T., Matsushita, A., Mochikawa, H., & Otaka, S. (2014) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec.2014.6803476 · Cited by 50 · cited 1×
“The SS compensation is used and intensively investigated at different resonance frequencies from kilohertz [49], [58]–[69] to megahertz [70]–[72], and power from several watts [62], [72], [73] to tens of kilowatts [21], [55], [74].”
MethodShi, W., Deng, J., Wang, Z., & Cheng, X. (2018) · IEEE Access · doi:10.1109/access.2018.2811179 · Cited by 47 · cited 1×
“The high-order compensation topologies such as the LCC and LCL have become more and more popular due to the better comprehensive performance [100], [102], [108]–[110].”
BackgroundAnalysis and control of S/SP compensation contactless resonant converter with constant voltage gain
Hou, J., Chen, Q., Yan, K., Ren, X., Wong, S., & Tse, C. K. (2013) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2013.6647030 · Cited by 46 · cited 2×
“In [10], [68], and [86]–[88] it is pointed that both the SS and SP compensations achieve CC/CV charging by choosing a suitable system operating frequency.”
BackgroundChen, C., Zhou, H. L., Deng, Q., Hu, W., Yanjuan, Y., Lu, X., & Lai, J. (2018) · IEEE Access · doi:10.1109/access.2018.2875413 · Cited by 45 · cited 1×
“In [10], [68], and [86]–[88] it is pointed that both the SS and SP compensations achieve CC/CV charging by choosing a suitable system operating frequency.”
BackgroundOptimizing Wireless Power Transfer From Multiple Transmit Coils
Arakawa, T., Goguri, S., Krogmeier, J. V., Kruger, A., Love, D. J., Mudumbai, R., & Swabey, M. A. (2018) · IEEE Access · doi:10.1109/access.2018.2825290 · Cited by 45 · cited 1×
“advantages of the three-coil system are the maximum energy efficiency, the energy efficiency stiffness against load variations and the reduced EMF emission induced by the coil misalignments [124], [125].”
BackgroundINDUCTIVE POWER TRANSFER TO AN ELECTRIC VEHICLE
Lashkari, K., Shladover, S. E., & Lechner, E. H. (1986) · Cited by 43
A Witricity-Based High-Power Device for Wireless Charging of Electric Vehicles
Dai, Z., Wang, J., Long, M., & Huang, H. J. (2017) · Energies · doi:10.3390/en10030323 · Cited by 43
Active resonance wireless power transfer system using phase shift control strategy
Zhao, C., Wang, Z., Du, J., Wu, J., Zong, S., & He, X. (2014) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec.2014.6803480 · Cited by 40
System Modeling and Switching Control Strategy of Wireless Power Transfer System
Jiang, J., Song, K., Li, Z., Zhu, C., & Zhang, Q. (2018) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2018.2804910 · Cited by 37
Analysis of efficiency improvement in wireless power transfer system
Liu, X., Wang, T., Yang, X., & Tang, H. (2017) · IET Power Electronics · doi:10.1049/iet-pel.2017.0029 · Cited by 36 · cited 1×
“The SS compensation is used and intensively investigated at different resonance frequencies from kilohertz [49], [58]–[69] to megahertz [70]–[72], and power from several watts [62], [72], [73] to tens of kilowatts [21], [55], [74].”
MethodLC/CL compensation topology and efficiency‐based optimisation method for wireless power transfer
Yao, Y., Liu, X., Wang, Y., & Xu, D. (2018) · IET Power Electronics · doi:10.1049/iet-pel.2017.0875 · Cited by 36 · cited 1×
“Efficiency of LC-LC topology may reach 92% [112].”
BackgroundMeng, X., Qiu, D., Lin, M., Tang, S. C., & Zhang, B. (2018) · IEEE Access · doi:10.1109/access.2018.2886424 · Cited by 35 · cited 1×
“The high-order compensation topologies such as the LCC and LCL have become more and more popular due to the better comprehensive performance [100], [102], [108]–[110].”
BackgroundLoad-Isolation Wireless Power Transfer With K-Inverter for Multiple-Receiver Applications
Kuang, J., Luo, B., Zhang, Y., Hu, Y., & Wu, Y. (2018) · IEEE Access · doi:10.1109/access.2018.2824334 · Cited by 25 · cited 1×
“The SIMO is also used for Maglev train with the series compensation on the primary side [130]; for the bidirectional Vehicle-To-Grid (V2G) systems multilevel IPT converters with 3 coils LCL compensation [131] and the load-isolation WPT with the 3-coil SSS compensation [132].”
MethodA graphical analysis on compensation designs of large-gap CPT systems for EV charging applications
Li, C., Zhao, X., Liao, C., & Wang, L. (2018) · CES Transactions on Electrical Machines and Systems · doi:10.30941/cestems.2018.00029 · Cited by 25 · cited 1×
“the EVs, but as experimental prototypes [140].”
Jamal, N., Saat, S., & Shukor, A. Z. (2013) · IEEE International Conference on Control System, Computing and Engineering · doi:10.1109/iccsce.2013.6719954 · Cited by 24 · cited 1×
“The paper [90] compares 4 main topologies with 9 cases, also in the cases where there is only a primary or a secondary compensation.”
BackgroundLiu, X., Liu, J., Wang, J., Wang, C., & Yuan, X. (2017) · Energies · doi:10.3390/en11010007 · Cited by 21
Jamal, N., Saat, S., Yusop, Y. B., Zaid, T., & Isa, A. A. M. (2015) · International Journal of Power Electronics and Drive Systems/International Journal of Electrical and Computer Engineering · doi:10.11591/ijpeds.v6.i2.pp274-281 · Cited by 21 · cited 1×
“Also at 1 MHz the SS topology provides a higher power transfer than the SP [91], [92], but the SP has a slightly better efficiency.”
BackgroundHong, H., Yang, D., & Won, S. (2017) · IEEE International Conference on Energy Internet (ICEI) · doi:10.1109/icei.2017.46 · Cited by 17 · cited 2×
“Comparison of dependences on mutual inductance for basic topologies: a) transfered power; b) efficiency [54].”
BackgroundLCL — LCCL voltage source inverter with phase shift control for wireless EV charger
Hatchavanich, N., Konghirun, M., & Sangswang, A. (2017) · IEEE International Conference on Power Electronics and Drive Systems (PEDS) · doi:10.1109/peds.2017.8289137 · Cited by 14 · cited 4×
“On the other hand, the large high-frequency current through a series capacitor will get the high capacitor voltage [104].”
BackgroundMethodInfluentialA novel wireless power charging system for electric bike application
Zhao, H., Shu, W., Li, D., & Li, S. (2015) · IEEE PELS Workshop on Emerging Technologies: Wireless Power Transfer · doi:10.1109/wow.2015.7132811 · Cited by 13 · cited 2×
“17c) [11], [81], [105], [77], [98], [99], [147] and other low-power transport devices.”
Method
Cited by
Inductive Wireless Power Transfer Charging for Electric Vehicles—A Review
Mahesh, A., Chokkalingam, B., & Mihet-Popa, L. (2021) · IEEE Access · doi:10.1109/access.2021.3116678 · Cited by 513
“Comparison of modified compensation topologies [140].”
MethodInfluential
Metadata
- Authors
- Shevchenko, V., Husev, O., Strzelecki, R., Pakhaliuk, B., Poliakov, N., & Strzelecka, N.
- Venue
- IEEE Access
- Published
- 2019
- Volume
- 7
- Pages
- 120559-120580
- ISSN
- 2169-3536 (ISSN-L)
- OpenAlex
- W2970480986
- Cited by
- 242
- References
- 85
- FWCI
- 7.23
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.