Reliability of Power Electronic Systems for EV/HEV Applications
Open accessThe DOI matches its Crossref record; 85 of the 88 references it cites were found in a registry or an index; 4 of the 45 sources its claims cite were checked for support.
Abstract
The electrification of the transportation sector is moving on at a fast pace. All car manufacturers have strong programs to electrify their car fleet to fulfill the demands of society and customers by offering carbon-neutral technologies to bring goods and persons from one location to another. Power electronics technology is, in this evolution, essential and also in a rapid development technology-wise. Some of the introduced technologies are quite mature, and the systems designed must have high reliability as they can be quite complicated from an electrical perspective. Therefore, this article focuses on the reliability of the used power electronic systems applied in electric vehicles (EVs) and hybrid EVs (HEVs). It introduces the reliability requirements and challenges given for the power electronics applied in EV/HEV applications. Then, the advances in power electronic components to address the reliability challenges are introduced as they individually contribute to the overall system reliability. The reliability-oriented design methodology is also discussed, including two examples: an EV onboard charger and the drive train inverter. Finally, an outlook in terms of research opportunities in power electronics reliability related to EV/HEVs is provided. It can be concluded that many topics are already well handled in terms of reliability, but issues related to complete new technology introduction are important to keep the focus on.
Overview
CoChat Summary
TL;DR
This article reviews reliability requirements, challenges, component advances, and reliability-oriented design for power electronics in EV/HEV applications. It demonstrates mission-profile-based lifetime assessment for a traction inverter and an onboard charger, finding very low predicted failure probabilities before a 600,000-km service target but noting substantial modeling uncertainties.
Key findings
- Automotive reliability requirements are severe: expected operating life >10 years, ambient temperature range −55 °C to 150 °C, and zero acceptable failure rate; temperature is the major stressor (55% of stress conditions in Table 1), with active thermal cycles ΔTj ≥ 100 °C.
- In the drive-train case, a 75-kW PMSM/330-V battery/400-A, 650-V IGBT module under an EUDC profile gives B0.001 lifetimes of approximately 500,000–1,300,000 km for the transistor and 600,000–1,500,000 km for the diode (90% CI); at the 600,000-km target, failure probability is approximately 0.0004% for the transistor, 0.0002% for the diode, and 0.004% for the entire power module.
- In the OBC case, a 560-µF/400-V dc-link capacitor in a 3.3-kW single-phase OBC has a B1 lifetime of approximately 500,000–2,500,000 km (90% CI), with approximately 0.025% probability of failure before 600,000 km.
- Component advances include reports that SiC MOSFETs with conventional packaging have lower power cycling capability than Si IGBTs, next-generation automotive modules expected to reach 175 °C, and CeraLink capacitors maintaining performance up to 150 °C.
Methods
- The article is a review plus case studies using a six-step mission-profile-based reliability assessment: driving cycle and ambient conditions → mechanical power → electrical loading → electrothermal modeling → empirical lifetime models → reliability block diagram system-level reliability.
- Case studies cover an EV drive train (75-kW PMSM, 330-V battery, 400-A/650-V IGBT module, EUDC mission profile) and a 3.3-kW single-phase OBC (560-µF/400-V dc-link capacitor, standard charging profile), using Rainflow counting, the LESIT lifetime model, Weibull shape parameter β = 3, Monte Carlo simulation with 5% lifetime-coefficient variation, and 90% confidence intervals.
- Thermal modeling uses junction-to-case temperature only; the coolant temperature is assumed to be 75 °C because outer thermal-network information was limited.
Limitations
- Stated: reliability results are subject to uncertainties from environmental mission profiles, electrothermal modeling, and lifetime models, and the error margins can significantly reduce confidence in predicted lifetime; due to high uncertainty, the metrics are used for relative benchmarking rather than as direct lifetime indicators.
- Stated: vibration, dust, and contamination are not considered because of a lack of empirical lifetime models; software failures and battery technology are excluded, and the focus is limited to thermal-related wear-out of power semiconductors and capacitors.
- Stated/evident: the lack of publicly available empirical lifetime models for automotive-qualified IGBT modules led to use of the LESIT model at B10 lifetime with 50% confidence and extrapolation to lower failure probabilities; modeling only junction-to-case temperature with an assumed 75 °C coolant further limits thermal representation.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures




![Fig. 5 R&D and lifetime requirements in EV/HEV. (a) Power electronics R&D development roadmap for electric-based vehicles based on the reports in [38] and [39]. (b) Automotive lifetime requirements based on [39], * [40], ** [38], and *** [41].](https://figures.cochat.ai/paper-figures/16b2b895451544858b0fc9e372c6aefa/reliability-of-power-electronic-systems-for-ev-hev-applications-figure-5.png)
![Fig. 6 Advances in packaging elements for power modules [18].](https://figures.cochat.ai/paper-figures/41a8f71cf76147d9b1432b384fc74271/reliability-of-power-electronic-systems-for-ev-hev-applications-figure-6.png)

![Fig. 8 Typical operational mission profiles for the two subassemblies. (a) Electric vehicle driving cycle [80]. (b) Scaled-down power demand for an EV OBC (based on [81]).](https://figures.cochat.ai/paper-figures/68c177e618b44bcb9d952857c7b98b4a/reliability-of-power-electronic-systems-for-ev-hev-applications-figure-8.png)










Verification
Claims the paper makes
1 Valid · 9 Not valid · 32 Not checked · 46 Own results and interpretations
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“Besides, the ambient temperature under the hood could be as high as 100 ◦ C with high humidity [77].”
What the sources say
- Could not verifycites [77] matched to “Electric-Vehicle Power Converters Model-Based Design-for-Reliability” (2018) sourceExperimental — accuracy not yet measured
The Thermal Model section treats ambient temperature as a constant model input, but does not describe conditions under a vehicle hood. Searches for 100°C ambient temperature, under-hood conditions, and humidity found no passage supporting the claimed temperature or humidity. (LLM, conf=0.74)
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“Therefore, advanced cooling technologies, such as spray cooling and jet impingement, are developed to meet the demands of the automotive industry [79].”
What the sources say
- Could not verifycites [79] matched to “Mission Profile Based System-Level Reliability Analysis of DC/DC Converters for a Backup Power Application” (2018) sourceExperimental — accuracy not yet measured
The Introduction discusses temperature-related reliability, and Section II mentions a coolant loop for a telecom backup fuel-cell system; neither addresses automotive cooling technologies. Searches for spray cooling, jet impingement, and automotive thermal management found no passage supporting the claim. Page numbers were unavailable in our copy. (LLM, conf=0.76)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“the dc-link capacitor of the OBC has a 1% probability of failure between 500 000 and 2 500 000 km, with a 90% confidence interval.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 2 assumptions not shown here.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“However, as shown in Table 2, there is a lack of qualification standards for power semiconductor modules.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
None of the sources cited for this claim have been checked yet.
In the paper
“As can be seen from the table, temperature stress is a major stressor that destroys power electronic components.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
33 more claims
Create a free account to see all 88 claims and to verify the 2 references still open.
- Probably not a substantial claim. 42
- It may state two separate claims as one. 16
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ III. A D V A N C E S I N P O W E R E L E C T R O N I C C O M P O N E N T S T O A D D R E S S R E L I A B I L I T Y C H A L L E N G E S · p. 7
“this article focuses on the advances in power modules and capacitors only in Section III”
§ C. Cooling Assemblies and Concepts · p. 9
“## C. Cooling Assemblies and Concepts”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ B. Reliability Analysis of an Electric Vehicle Case Study · p. 10
“The overall topology configurations of the electrical drive train main inverter and the onboard EV charger for the two selected subassemblies are shown in Figs. 3 and 5, respectively.”
§ A. Power Modules · p. 8
“Fig. 5. R&D and lifetime requirements in EV/HEV.”
Citations
Cites
An Industry-Based Survey of Reliability in Power Electronic Converters
Yang, S., Bryant, A., Mawby, P., Xiang, D., Ran, L., & Tavner, P. (2011) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2011.2124436 · Cited by 2,019
Handbook of software reliability engineering
Lyu, M. R.-T. (1996) · McGraw-Hill, Inc. eBooks · Cited by 1,592
Electrical Machines and Drives for Electric, Hybrid, and Fuel Cell Vehicles
Zhu, Z. Q., & Howe, D. (2007) · Proceedings of the IEEE · doi:10.1109/jproc.2006.892482 · Cited by 1,547 · cited 1×
“Intensive research and development are currently going on enhancing PM EMs and adopting different types of EMs in order to further improve the performance of future electric-based vehicles [48].”
MethodEmadi, A., Lee, Y. J., & Rajashekara, K. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.922768 · Cited by 1,461 · cited 1×
“Notably, different possible configurations for the power train in EV/HEV can be found in the automotive market [25]–[28].”
BackgroundReliability of Capacitors for DC-Link Applications in Power Electronic Converters—An Overview
Wang, H., & Blaabjerg, F. (2014) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2014.2308357 · Cited by 1,384 · cited 3×
“Besides active components, the capacitor reliability is also essential to understand and take into consideration when doing reliability analysis for the complete system [20].”
BackgroundInfluentialSelf-citationModern Electric, Hybrid Electric, and Fuel Cell Vehicles: Fundamentals, Theory, and Design
Ehsani, M., Gao, Y., Gay, S. E., & Emadi, A. (2004) · CRC Press eBooks · doi:10.1201/9781420037739 · Cited by 1,248
Closed-loop optimization of fast-charging protocols for batteries with machine learning
Attia, P. M., Grover, A., Jin, N., Severson, K. A., Markov, T. M., Liao, Y.-H., Chen, M. H., Cheong, B., Perkins, N., Yang, Z., et al. (2020) · Nature · doi:10.1038/s41586-020-1994-5 · Cited by 1,180
Toward Reliable Power Electronics: Challenges, Design Tools, and Opportunities
Wang, H., Liserre, M., & Blaabjerg, F. (2013) · IEEE Industrial Electronics Magazine · doi:10.1109/mie.2013.2252958 · Cited by 916 · cited 1×
“knowledge base (physics of failure), a design stage (DfR and robustness validation), and an operational phase (intelligent control and condition monitoring) [10]–[12].”
BackgroundSelf-citationThe Essence of Three-Phase PFC Rectifier Systems—Part I
Kolar, J. W., & Friedli, T. (2013) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2012.2197867 · Cited by 788 · cited 1×
“Notably, depending on the topology, the HV dc bus voltage will be different [32], [33].”
BackgroundPractical Reliability Engineering
O'Connor, P. D. T., & Kleyner, A. (2011) · Wiley eBooks · doi:10.1002/9781119961260 · Cited by 783
Research works printed but not linked: 32
- Frede Blaabjerg (Fellow, IEEE) received the Ph.D. degree in electrical engineering from Aalborg University, Aalborg, Denmark, in 1995.
- He was with ABB-Scandia, Randers, Denmark, from 1987 to 1988. He became an Assistant Professor in 1992, an Associate Professor in 1996, and a Full Professor of power electronics and drives in 1998 at Aal- converters for aircraft applications,' IEEE Trans. Aerosp. Electron. Syst. , vol. 48, no. 2, pp. 1249-1263, Apr. 2012.
- 2018, The Roadmap Report Towards 2040 A Guide to Automotive Propulsion Technologies
- 2018, Shaping Future Electromobility With Semiconductor Innovations
- 2015, Handbook for Robustness Validation of Semiconductor Devices in Automotive Applications
- ehsani, 2018, Modern Electric Hybrid Electric and Fuel Cell Vehicles
- drexhage, 2016, Effect of humidity and condensation on power electronics systems
- 2013, Electric and Electronic Components in Motor Vehicles up to 3 5t
- 2020, Electric vehicle outlook 2020
- 2013, Failure Mechanism Based Stress Test Qualification for Discrete Semiconductors in Automotive Applications REV D1
- 2017, Electrical and electronics technical team roadmap
- 2008, Vorlesung Qualtat und Zuverlassigkeit von Fahrzeug e/e Hardware an der tu Berlin
- 2010, Stress Test Qualification for Passive Components
- 2013, Zvei Die Elektroindustrie Handbook for Robustness Validation of Automotive Electrical/Electronic Modules
- allouche, 2020, Hitachi DSC Power Module From Audi e-Tron Inverter
- christmann, 2009, Reliability of power modules in hybrid vehicles, Proc PCIM Eur, 359
- 2019, Qualification of Power Modules for Use in Power Electron Converter Units in Motor Vehicles
- ishihara, 2012, New transfer-mold power module series for automotive power-train inverters, Proc PCIM Eur, 1408
- ishihara, 2014, New compact-package power modules for electric and hybrid vehicles (J1 series), Proc PCIM Eur, 1093
- kimura, 2014, High-power-density inverter technology for hybrid and electric vehicle applications, Hitachi Rev, 63, 41
- knappik, 2019, The advantages of 48-volt vehicle electronics, Veh Technol
- Standard Practices for Cycle Counting in Fatigue Analysis , ASTM Int., A. C. E. Fatigue Fract., West Conshohocken, PA, USA, 2005.
- M. Musallam and C. M. Johnson, 'An efficient implementation of the rainflow counting borg University, where he became a Villum Investigator in 2017. He is also honoris causa at Universitatea Politehnica Timisoara (UPT), Romania, and the Tallinna University of Technology (TTU), Tallinn, Estonia. He has published more than 600 journal articles in the fields of power electronics and its applications. He is a coauthor of four monographs and editor of ten books in power electronics and its applications. His current research interests include power electronics and its applications, such as in wind turbines, PV systems, reliability, harmonics, and adjustable speed drives.
- Dr. Blaabjerg received 32 IEEE Prize Paper Awards, the IEEE Power Electronics Society (PELS) Distinguished Service Award in 2009, the EPE-PEMC Council Award in 2010, the IEEE William E. Newell Power Electronics Award in 2014, the Villum Kann Rasmussen Research Award in 2014, the Global Energy Prize in 2019, and the 2020 IEEE Edison Medal. He was nominated in 2014-2019 by Thomson Reuters to be between the most 250 cited researchers in engineering in the world. He was the Editor-in-Chief of IEEE TRANSACTIONS ON POWER ELECTRONICS from 2006 to 2012. He was a Distinguished Lecturer of the IEEE Power Electronics Society from 2005 to 2007 and the IEEE Industry Applications Society from 2010 to 2011 and 2017 to 2018. From 2019 to 2020, he has served as the President of the IEEE Power Electronics Society. He is also the Vice-President of the Danish Academy of Technical Sciences. algorithm for life consumption estimation,' IEEE Trans. Rel. , vol. 61, no. 4, pp. 978-986, Dec. 2012.
- Huai Wang (Senior Member, IEEE) received the B.E. degree in electrical engineering from the Huazhong University of Science and Technology, Wuhan, China, in 2007, and the Ph.D. degree in power electronics from the City University of Hong Kong, Hong Kong, in 2012.
- A. Wintrich, U. Nicolai, W . Tursky, and T. Reimann, Application Manual Power Semiconductors , 2nd ed. Ilmenau, Germany: Semikron International GmbH, 2015.
- Dr. Wang received the Richard M. Bass Outstanding Young Power Electronics Engineer Award from the IEEE Power Electronics Society in 2016 and the Green Talents Award from the German Federal Ministry of Education and Research in 2014. He is also the Chair of the IEEE Power Electronics Society (PELS)/Industrial Application Society (IAS)/Industrial Electronics Society (IES) Chapter in Denmark. He also serves as an Associate Editor for Electronics Letters (IET), IEEE JOURNAL OF EMERGING AND SELECTED TOPICS IN POWER ELECTRONICS, and IEEE TRANSACTIONS ON POWER ELECTRONICS.
- Ionut Vernica (Member, IEEE) received the B.Sc. degree in electrical engineering from the Politehnica University of Bucharest, Bucharest, Romania, in 2014, and the M.Sc. and Ph.D. degrees in energy engineering from Aalborg University, Aalborg, Denmark, in 2016 and 2019, respectively.
- Bochen Liu (Member, IEEE) received the B.S. and M.S. degrees in electrical engineering and power electronics from Southeast University, Nanjing, China, in 2014 and 2017, respectively. He is currently working toward the Ph.D. degree in power electronics at Aalborg University, Aalborg, Denmark.
- He was a Student Visitor with the University of Cambridge, Cambridge, U.K., in 2020.
- Pooya Davari (Senior Member, IEEE) received the B.Sc. and M.Sc. degrees in electronic engineering from the University of Mazandaran (Noushirvani), Babolsar, Iran, in 2004 and 2008, respectively, and the Ph.D. degree in power electronics from the Queensland University of Technology (QUT), Brisbane, QLD, Australia, in 2013.
- Dr. Davari is a member of the International Scientific Committee (ISC) of EPE (ECCE Europe) and the Joint Working Group Six and Working Group Eight at the IEC Standardization TC77A. He was a recipient of a research grant from the Danish Council of Independent Research (DFF-FTP) in 2016 and the 2020 IEEE EMC Society Young Professional Award for his contribution to EMI and Harmonic Mitigation and Modeling in Power Electronic Applications. He has served as a Guest Associate Editor for IET Power Electronics , IEEE ACCESS, International Journal of Electronics , and Journal of Applied Sciences . He is also an Associate Editor of Journal of Power Electronics , an Associate Editor of Electronics Letters (IET), and an Editorial Board Member of EPE Journal and Journal of Applied Sciences . He is also the Editor-in-Chief of Circuit World .
Cited by
Items 101–200 of 241
An Active Discharge Scheme for DC-Bus Capacitors in EV Powertrain
Sezer, M. M., Norwood, D., Geiger, J., Hava, A. M., & Akin, B. (2025) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2025.3590734 · Cited by 4
“T HE powertrain of an electric vehicle (EV) is a sophisticated system that converts electrical energy from the battery into mechanical energy to drive the wheels [1].”
Gao, C., Li, S., Yao, Q., Li, Y., Liu, J., Tian, T., Wang, L., Wu, S., & Ye, H. (2024) · International Conference on Electronic Packaging Technology (ICEPT) · doi:10.1109/icept63120.2024.10668777 · Cited by 5
“In the field of power electronics, the power module plays a key role in the stable operation of the system, and its reliability is crucial for the smooth functioning of the entire system[3], [4], [5].”
BackgroundLifetime Estimation of GaN based DC-DC Converter of Electric Vehicle Application
Saha, S., & Das, M. (2022) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon49645.2022.9968457 · Cited by 5
“It is necessary for semiconductor devices to meet the life expectancy requirements for an EV component (a traction inverter, and a DC-DC converter) of 300,000 km/15 years [4,5].”
BackgroundParameter identification of DC–DC converter based on dendrite net under fluctuating input voltages
Jiang, Y., Liu, Y., & Yang, Z. (2023) · IET Power Electronics · doi:10.1049/pel2.12529 · Cited by 4
Yeo, S. M., Yow, H. K., & Yeoh, K. H. (2023) · IEEE Transactions on Components Packaging and Manufacturing Technology · doi:10.1109/tcpmt.2023.3293114 · Cited by 4
Adăscăliţei, C., Marțiș, R. A., Karaisas, P., & Martis, C. S. (2024) · Machines · doi:10.3390/machines12060361 · Cited by 8
Novel Adaptive Energy Management Technique for Multi-Port Fast EV Chargers
Sharida, A., Kamal, N. F., Bayhan, S., Abu‐Rub, H., & Feslı, U. (2024) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2024.3409896 · Cited by 3
A System-Level Design for Reliability of Integrated Motor Drives
Atashin, S. A., Peyghami, S., Davari, P., Chopade, A. R., Hanigovszki, N., & Blaabjerg, F. (2024) · International Conference on Electrical Machines (ICEM) · doi:10.1109/icem60801.2024.10700144 · Cited by 5
“Power switches and their body diodes, the microcontroller unit (MCU), and also the DC link capacitor have the most effect due to the heat and vibration of the EM [5], [6].”
BackgroundSelf-citationReliability research of thyristors for HVDC transmission system
Xu, Y., Pang, L., Xie, T., et al. (2024) · Scientific Reports · doi:10.1038/s41598-024-77351-4 · Cited by 4
Murillo-Yarce, D., Colvero, G. D., Gómez, A. A., Díaz, J. T., Rodríguez, A., & Vázquez, A. (2025) · Electronics · doi:10.3390/electronics14020215 · Cited by 5
de Sousa, R. O., Barros, R. C. D., Amorim, W. C. S., Cupertino, A. F., Pereira, H. A., & Morais, L. M. F. (2025) · Eletrônica de Potência · doi:10.18618/rep.e202532 · Cited by 4
“A significant portion of this expansion is driven by power electronics technology, which enables the efficient control of power flow [1], [2].”
Multi-Objective Parametric Analysis of EV Traction Inverter between Reliability and Efficiency
Gill, L., Rashkin, L., Yates, L., Neely, J. C., & Kaplar, R. (2023) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec43580.2023.10131644 · Cited by 5
“This paper provides an extension of the previous work of the multi-objective genetic algorithm implementation for power conversion systems in [19], [20] with a mission-profile driven and reliability-oriented design process outlined in [21].”
Thermal simulation of a 7kW interleaved module for fast automotive charger
Anoldo, L., Piccione, G. G., Mauromicale, G., Sitta, A., Fazio, E., Calabretta, M., Lionetto, A., Messina, A. A., Guardo, M. D., & Patanè, S. (2021) · IEEE International Conference on Environment and Electrical Engineering and IEEE Industrial and Commercial Power Systems Europe (EEEIC / I&CPS Europe) · doi:10.1109/eeeic/icpseurope51590.2021.9584683 · Cited by 4
Comparative Analysis of Ideal Energy Requirements in EV Powertrains
Demir, U., Ehsani, M., Demir, P., et al. (2025) · Iranian Journal of Science and Technology Transactions of Electrical Engineering · doi:10.1007/s40998-025-00809-2 · Cited by 3
“The improvements obtained reduce energy transfer losses, and the achieved maximum effi-ciency reaches 95% (Emadi et al. 2008; Blaabjerg et al. 2021; Hannan et al. 2019; Status and Trends 2020).”
Murillo-Yarce, D., Colvero, G. D., Lamar, D. G., Rodríguez, A., & Vázquez, A. (2024) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec48139.2024.10509320 · Cited by 5
“Electric vehicle (EV) has been a major focus of interest in recent years, due to the widespread effort to develop transportation methods with a reduced environmental footprint [1], [2].”
BackgroundProcess-induced influences on epoxy-based encapsulated reliability of high power modules
Lee, C., Chen, M.-T., & Chuang, J. (2025) · International Journal of Mechanical Sciences · doi:10.1016/j.ijmecsci.2025.110394 · Cited by 13
Lead-Free BiSnAg Soldering Process for Voidless Semiconductor Packaging
Yeo, S. M., Yow, H. K., & Yeoh, K. H. (2023) · IEEE Transactions on Components Packaging and Manufacturing Technology · doi:10.1109/tcpmt.2023.3299334 · Cited by 3
Ma, M., Wang, N., Wang, H., Guo, W., & Wang, H. (2023) · IET Power Electronics · doi:10.1049/pel2.12569 · Cited by 3
Self-citationTIMs for transfer molded power modules: Characterization, reliability, and modeling
Sitta, A., Mauromicale, G., Malgioglio, G. L., et al. (2023) · Microelectronics Reliability · doi:10.1016/j.microrel.2023.115162 · Cited by 3
In-Circuit Assessment of the Long-Term Reliability of E-Mode GaN HEMTs
Capasso, G., Zanuccoli, M., Tallarico, A. N., & Fiegna, C. (2023) · IEEE Transactions on Electron Devices · doi:10.1109/ted.2023.3318865 · Cited by 3
“Power semiconductor devices are the most prone-to-failure components in power converters [4].”
BackgroundModified Rainflow Algorithm for Lifetime Estimation of Semiconductors Devices
de Sousa, R. O., Barros, R. C. D., Amorim, W. C. S., et al. (2023) · doi:10.1109/spec56436.2023.10408046 · Cited by 3
“Consequently, the electrical power system is continuously expanding, mostly enabled by the power electronics technology’s ability to efficiently control the power flow [1].”
BackgroundBhanuchandar, A., & Murthy, B. K. (2023) · IEEE India Council International Conference (INDICON) · doi:10.1109/indicon59947.2023.10440745 · Cited by 3
“To attenuate these drawbacks, the multilevel converters are very useful and they reduce power filer size and need only a low voltage rating of switches [9].”
BackgroundDirect Connection of EV Fast Charging Station to Medium Voltage AC Grid
Azimi, E., & Wei, Q. (2024) · International Power Electronics and Motion Control Conference (EPE-PEMC) · doi:10.1109/ipemc-ecceasia60879.2024.10567669 · Cited by 4
“Electrification can dramatically reduce fuel usage, greenhouse emissions, and noise levels [1].”
BackgroundSundararajan, P., Siddique, M. D., Sahani, M., et al. (2024) · IEEE International Symposium on Power Electronics for Distributed Generation Systems (PEDG) · doi:10.1109/pedg61800.2024.10667455 · Cited by 3
“Power electronic converters play a crucial role in the modern-day energy and transportation sector aiding the transition towards better efficiency and sustainability [1]-[2].”
BackgroundKlints, A. K., Bogdanovs, A., & Zarembo, J. (2022) · IEEE International Scientific Conference on Power and Electrical Engineering of Riga Technical University (RTUCON) · doi:10.1109/rtucon56726.2022.9978854 · Cited by 3
“Also, the most important guideline is design of an effective cooling system overall to achieve higher power density [2], [7].”
BackgroundNguyen, V. H., Do, X.-D., Blaquière, Y., et al. (2022) · IEEE Interregional NEWCAS Conference (NEWCAS) · doi:10.1109/newcas52662.2022.9842223 · Cited by 3
Zhaksylyk, A., Hasan, M. M., Chakraborty, S., et al. (2022) · Proceedings of the Annual Conference of the IEEE Industrial Electronics Society · doi:10.1109/iecon49645.2022.9968778 · Cited by 3
“Many developed nations are committing to significantly limit the number of internal combustion engine (ICE) vehicles, and have the majority of new cars electrified [2].”
BackgroundPI_BPNN controller for transient response improvement of LLC resonant converter
Kim, H., Kim, J., Chin, T., Choi, H., & Cho, Y. (2023) · Journal of Power Electronics · doi:10.1007/s43236-023-00608-0 · Cited by 3
“5a. Analyses of the operating regions of LLC converters can be found in [1–4].”
BackgroundHan, D.-G., Lee, D.-H., & Yoon, J. (2024) · Journal of Welding and Joining · doi:10.5781/jwj.2024.42.2.3 · Cited by 2
Salem, A., Darras, B. M., & Nazzal, M. A. (2025) · Energies · doi:10.3390/en18061527 · Cited by 4
“PCBs containing higher percentages of precious metals contribute to safer EVs with better-performing battery management systems (BMS), faster charging, and efficient charge distribution [8].”
Thermal Evaluation of PSFB Converters Under Constant Current and Pulsed Current Charging Strategies
Karakus, B., & Akboy, E. (2025) · IEEE International Conference on Compatibility, Power Electronics and Power Engineering · doi:10.1109/cpe-powereng63314.2025.11027237 · Cited by 2
“Therefore, governments, industry, and academia support fast adoption of EVs [1].”
Multi-Objective Design Optimization of EV Inverter for Efficiency, Volume, and Reliability
Gill, L., Neely, J. C., Yates, L., Kaplar, R., & Michaels, A. J. (2025) · IEEE Transportation Electrification Conference and Expo · doi:10.1109/itec63604.2025.11098054 · Cited by 2
“In essence, improving efficiency leads to reduced power losses and can extend driving range or reliability [5].”
Toward Ethical AI in Power Electronics: How Engineering Practice and Roles Must Adapt
Lin, F., Wilson, P., Li, X., & Mantooth, A. (2026) · IEEE Power Electronics Magazine · doi:10.1109/mpel.2025.3646734 · Cited by 2
“Power electronics is a technology that has vital importance in many cases, being an essential technology used in mission-critical systems such as electric transportation and microgrids, where failures can result in consequences that are not only costly but also potentially catastrophic [2].”
Electric Vehicle Fast Charging Technologies and Grid Integration—A Comprehensive Review
Sharida, A., Kamal, N. F., Bayhan, S., & Abu-Rub, P. D. H. (2025) · Proceedings of the IEEE · doi:10.1109/jproc.2026.3677611 · Cited by 4
Utilizing Electroluminescence of Silicon IGBTs for Junction Temperature Sensing
Ruppert, L. A., Wirsen, B., Kalker, S., & Doncker, R. W. D. (2023) · International Conference on Power Electronics and ECCE Asia (ICPE-ECCE Asia) · doi:10.23919/icpe2023-ecceasia54778.2023.10213620 · Cited by 3
Hybrid Modulation for Balancing Thermal Dissipation in Dual Active Bridge Converters
Liu, B., Davari, P., & Blaabjerg, F. (2023) · European Conference on Power Electronics and Applications · doi:10.23919/epe23ecceeurope58414.2023.10264301 · Cited by 2
“The former plays a more important role in the wear-out failures due to the nonconstant thermal expansion coefficients between different material layers, and the latter is more likely to cause catastrophic damage to the power device during transient or short-term operation [2, 3], especially when the ambient temperatur…”
BackgroundSelf-citationData Loggers for High-Temperature Industrial Environments
Cecchi, R., Catania, A., Sbrana, C., et al. (2024) · IEEE Access · doi:10.1109/access.2024.3509581 · Cited by 2
Digital Twin Model of High-frequency Transformer Applied in Flyback Converter for Fault Diagnosis
Licheng, Z., Song, J., & Wang, Z. (2024) · International Symposium on Electrical, Electronics and Information Engineering (ISEEIE) · doi:10.1109/iseeie62461.2024.00027 · Cited by 2
“Recent progresses on the embedded artificial intelligence (AI) technology accelerate researches on the online health monitoring [4], which has good application prospects for the power supplies with high reliability requirements, such as electric automobile and aviation[5].”
Raghavendra Rao, N. S., Chitra, A., Krishnachaitanya, D., et al. (2025) · IEEE Access · doi:10.1109/access.2025.3540458 · Cited by 2
A Review of Reliability Evaluation Methods for Electric Vehicle Charging Infrastructure
Mlindelwa, S., Chowdhury, S. D., & Lencwe, M. J. (2025) · Southern African Universities Power Engineering Conference (SAUPEC) · doi:10.1109/saupec65723.2025.10944318 · Cited by 3
“It is assumed in series reliability models that when each component fails, the entire system fails [26].”
Kanakri, H. M., dos Santos, E. C., & Rizkalla, M. (2025) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec48143.2025.10977543 · Cited by 2
“However, capacitors are susceptible to wear-out mechanisms and failure modes, which can result in increased monitoring and replacement costs for systems utilizing them [7].”
Shirly, A. R. D., & Suganyadevi, M. V. (2025) · Iranian Journal of Science and Technology Transactions of Electrical Engineering · doi:10.1007/s40998-025-00907-1 · Cited by 2
“At the core of these solar-powered EVs is the BLDC motor, which is well-suited for use in electric vehicles due to its high efficiency, durabil - ity, and quiet operation (Blaabjerg et al. 2020 ; Kraiem et al. 2021 ; Wang et al. 2022 ).”
Comparative Study Between the Ćuk and the LLC Converter in Photovoltaic Applications
Hasan, M. N., & Polom, T. A. (2021) · IEEE International Conference on Compatibility, Power Electronics and Power Engineering · doi:10.1109/cpe-powereng50821.2021.9501087 · Cited by 2
FEPPCON XI – Part II: Reliability of Power Electronic Systems
Wang, H., PECHT, M. G., Mertens, A., DeDoncker, R. W., & Blaabjerg, F. (2023) · IEEE Power Electronics Magazine · doi:10.1109/mpel.2023.3236463 · Cited by 2
“March 2023 z IEEE POWER ELECTRONICS MAGAZINE 51 electronics-based power systems were considered as two of the most critical applications in the next decade regarding the degree of challenge to designers and reliability engineers [9], reliability requirements, and market size.”
BackgroundSelf-citationModel Predictive Control for Scalable Power Converters with Reconfigurable Architecture
Zhou, L., Fahmy, Y., Jahnes, M., & Preindl, M. (2023) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce53617.2023.10362419 · Cited by 2
An Outlook on Power Electronics Reliability and Reliability Monitoring
Martin, H., Smits, E. C. P., Poelma, R. H., van Driel, W. D., & Zhang, G. (2024) · Springer eBooks · doi:10.1007/978-3-031-59361-1_10 · Cited by 2
Reliability Improvement of Power Devices for Electric Vehicle Traction
Adnan, S. M., Haque, A., & K, V. S. B. (2021) · IEEE International Conference on Computing, Power and Communication Technologies (IC2PCT) · doi:10.1109/gucon50781.2021.9573816 · Cited by 2
“It is fundamental to make a decent cooling framework so that segment's temperature never surpasses its predetermined most extreme voltage [1], [8].”
BackgroundSalim, M., & Safarzadeh, O. (2024) · IET Generation Transmission & Distribution · doi:10.1049/gtd2.13318 · Cited by 1
Digital Twin of Power Modules based on Physics Informed Machine Learning
Hu, B., Mu, W., Zhu, H. J., et al. (2024) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce55643.2024.10861878 · Cited by 1
A Novel Thermal Modeling Analysis for Liquid-Cooled High-Power EV Chargers
Bradford, P., Zade, A., Gurudiwan, S., & Wang, H. (2024) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce55643.2024.10861307 · Cited by 1
Self-citationSachs, C., Gliese, F., & Neuburger, M. (2025) · Proceedings in Technology Transfer · doi:10.1007/978-3-031-79093-5_6 · Cited by 1
Real-Time Lifetime Prediction of Semiconductor Devices Using Hardware-in-the-Loop
Gill, L., Seo, G., & Michaels, A. J. (2024) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon55916.2024.10905496 · Cited by 1
“It calculates cumulative damage over time [14] and leverages these calculations to estimate the device’s mean time to failure [15]–[17].”
A Hybrid Cuk PFC Converter for 48 V – 12 Ah Battery Charging Application
Al-Hysam, A., Ihsan, M. A., Eram, A. F., et al. (2024) · International Conference on Sustainable Technologies for Industry 5.0 (STI) · doi:10.1109/sti64222.2024.10951125 · Cited by 1
Wu, Y., Choksi, K., Defaz, S., et al. (2025) · IEEE Transactions on Electromagnetic Compatibility · doi:10.1109/temc.2025.3571381 · Cited by 1
Nikzadfar, K., Stone, T., Caine, J., Abbasian, M., Babaie, M., Goswami, R., Ghanami, N., Sheikh, M., & Azadi, M. (2025) · Energy, environment, and sustainability · doi:10.1007/978-981-96-6624-9_4 · Cited by 2
Automatic Charging E-Vehicle Using Electrical Generator
Tamilselvi, S., Jansi, S., Janani, M., & Thirumurugan, S. (2025) · International Conference on Circuit, Power and Computing Technologies · doi:10.1109/iccpct65132.2025.11176617 · Cited by 1
Comparative Analysis of TSD and NTC-Based Temperature Measurement for Power Semiconductor Modules
Agirrezabala, E., Cancho, A. P., Garcia, M. L., Larrañaga, I. A., & Garrido, D. (2025) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon58223.2025.11221266 · Cited by 1
“Power electronics, particularly power converters, are being used more often in applications that require efficient and reliable generation, transportation, or consumption of electric power [3].”
Alatise, O. M., Gonzalez, J. A. O., Jahdi, S., et al. (2025) · doi:10.1109/ecce58356.2025.11259761 · Cited by 1
“…which typically incudes large amplitude power spikes at high frequency as the vehicle undergoes full power acceleration, cruising and braking [3] Furthermore, power flow through the EV traction converter is bi-directional since power flows from the battery to the motor through the…”
Online Monitoring Method for Bond-Wires Lift-Off of IGBT Based on Turn-Off Gate Voltage Valley
Yang, K., Xu, P., Song, W., Tan, H., Chen, J., & Liu, B. (2025) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2025.3646296 · Cited by 1
“I NSULATED gate bipolar transistors (IGBTs) have become the cornerstone devices in modern industrial applications, ranging from motor drives, renewable energy systems, and industrial automation [1], [2].”
Self-citationAn Online Bond-Wires Lift-off Monitoring Method for IGBT Without Effect of Operation Conditions
Yang, K., Xu, P., Song, W., Tan, H., Chen, J., & Liu, B. (2026) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2026.3658746 · Cited by 3
Self-citationGrid-Integrated EV Charging with Hybrid Filters for Enhanced Harmonic Suppression
Sumalatha, S., & Obulesu, Y. P. (2026) · Smart Grids and Sustainable Energy · doi:10.1007/s40866-025-00315-8 · Cited by 1
A Non-Ecap Wide Range Bidirectional OBC With Multifunction Circuit
Tran, H. N., Nguyen, L. H. B., Vo, M. V., & Nguyen, T. D. (2026) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2026.3680312 · Cited by 1
“Reliability is a key concern for EV power converters, with OBC expected to provide 15 years of service lifetime [24].”
Schmalzl, S., von Bonin, M., Frey, M., Gauterin, F., & Braun, M. (2026) · Energy Reports · doi:10.1016/j.egyr.2026.109349 · Cited by 2
Dynamic Thermal Design of an Active Power Cycling Test Bench for SiC MOSFETs
Nitzsche, M., Ziegler, P., Michelberger, A., Barón, K. M., Ruthardt, J., & Roth‐Stielow, J. (2021) · European Conference on Power Electronics and Applications · doi:10.23919/epe21ecceeurope50061.2021.9570564 · Cited by 1
Sundararajan, P., Siddique, M. D., & Panda, S. K. (2023) · International Conference on Power Electronics and ECCE Asia (ICPE-ECCE Asia) · doi:10.23919/icpe2023-ecceasia54778.2023.10213963 · Cited by 1
“transportation industry from fossil fuels-based vehicles to electric vehicles (EV) [2]-[4].”
BackgroundComputationally Efficient Dynamic Thermal Modeling Based on Dictionary Learning Reconstruction
Zhang, X., Zhang, Y., Zhou, D., Wu, X., & Wang, H. (2023) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2023.3317249 · Cited by 1
Self-citationWei, X., Jin, L., Yao, B., Peng, Y., & Wang, H. (2023) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2023.3339848 · Cited by 3
“…operating power, the power semiconductor devices in the current traction inverter are commonly insulated gate bipolar transistors (IGBTs), which are expected to be replaced by silicon carbide (SiC) and gallium nitride (GaN) devices in the future to further reduce power loss and system size [3].”
BackgroundSelf-citationReliability assessment and accelerated life testing in a metalworking plant
Wofuru-Nyenke, O. K. (2024) · Future Technology · doi:10.55670/fpll.futech.3.3.1 · Cited by 1
Beyond-Nominal Operation of GaN-Based Converters for High-Power Density Applications
Hussain, A., Sado, K. A., Perez, D., & Booth, K. (2024) · IEEE Transportation Electrification Conference and Expo · doi:10.1109/itec60657.2024.10598924 · Cited by 1
“Therefore, the reliability of power converters should be given priority in the design process [4].”
BackgroundFault Prediction Algorithm of IGBT Devices Based on Bidirectional GRU Network Model
Yang, P., Li, H., Han, X., et al. (2024) · International Conference on Electronic Communication and Artificial Intelligence (ICECAI) · doi:10.1109/icecai62591.2024.10675302 · Cited by 1
Implementation of Interleaved DC-DC Converter for Fast Charging Stations using Microgrid System
Kumar, P. S., & Barik, S. K. (2024) · doi:10.1109/iccigst60741.2024.10717608 · Cited by 1
Buck Converter Parameters Design Using Artificial Intelligence-Based Genetic Algorithm
Laksheta, K., Sidik, Y. F., & Wijaya, F. D. (2024) · doi:10.1109/icitee62483.2024.10808195 · Cited by 1
Figueiredo, Y. P., Vitorino, M. A., & Friebe, J. (2024) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce55643.2024.10861506 · Cited by 2
Choi, N.-Y., Kim, S. J., & Zhang, S.-U. (2025) · Energies · doi:10.3390/en18102457 · Cited by 1
Anam, A., Kersten, A., Xu, Y., et al. (2025) · International Conference on Electrical Drives and Power Electronics (EDPE) · doi:10.1109/edpe66853.2025.11224067 · Cited by 1
“Lifetime modeling (reliability) of power electronics is a known topic from different applications, such as solar power [8], wind power [9] or battery electric vehicles [10].”
Vinod, M., Kishan, D., Harishchandrappa, N., et al. (2021) · IEEE International Power and Renewable Energy Conference (IPRECON) · doi:10.1109/iprecon52453.2021.9640965 · Cited by 1
Pan, W., Li, D., & Yang, X. (2023) · IEEE International Conference on Electronic Technology, Communication and Information (ICETCI) · doi:10.1109/icetci57876.2023.10176876 · Cited by 1
Wenk, M., Zimann, F. J., Mayer, R., et al. (2026) · Eletrônica de Potência · doi:10.18618/rep.e202614 · Cited by 1
“Supporting this transformation, various sectors have developed to address diverse requirements, encompassing not only manufacturing but also the maintenance and servicing of these vehicles [12].”
Electric Vehicle in Smart Grid Integrated Photovoltaic Environment with Storage SystemPreprint
MANISSEGARANE, S., & Rajan, C. A. (2023) · Research Square · doi:10.21203/rs.3.rs-2585963/v1 · Cited by 1
Power Converters for Hybrid Electric Vehicles
Gayathri, M. N. (2021) · Advances in mechatronics and mechanical engineering (AMME) book series · doi:10.4018/978-1-7998-7626-7.ch007
Impact of Operational Factors on the Lifetime of Power Semiconductor Devices in Electric Vehicles
Arya, A., Chanekar, A. A., Endla, N. K., Verma, A. K., & Anand, S. (2022) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon49645.2022.9968712
“The work presented in [9] emphasizes on the importance of reliability oriented design of power converters for EV applications.”
Background2022 Index Proceedings of the IEEE Vol. 108-110
(2022) · Proceedings of the IEEE · doi:10.1109/jproc.2023.3234419
The Proposed Artificial-Intelligence-Based Design (AI-D) for Circuit Parameters of Power Converters
Zhang, X., Li, X., Ma, H., Jingjing, H., & Zeng, Z. (2023) · Springer eBooks · doi:10.1007/978-981-99-0459-4_4
Zhang, X., Li, X., Ma, H., Jingjing, H., & Zeng, Z. (2023) · Springer eBooks · doi:10.1007/978-981-99-0459-4_1
Flexibility Probabilistic Prediction and Stochastic Optimal Dispatching of Electric Vehicle Clusters
Zhao, J., Xu, B., Zhang, P., et al. (2023) · Asia Conference on Power and Electrical Engineering (ACPEE) · doi:10.1109/acpee56931.2023.10135711
“Therefore, governments have actively promoted its rapid development through economic support, policy incentive, and regulatory compulsion [3].”
BackgroundSelf-citationWang, N., Ma, M., Chen, Q., & Wang, H. (2023) · IEEE International Electrical and Energy Conference (CIEEC) · doi:10.1109/cieec58067.2023.10166350
Self-citationAutomated Controller Hardware-In-The-Loop Testbed for EV Charger Resilience Analysis
Starke, M. R., Kim, N., Dean, B., Campbell, S. L., & Chinthavali, M. S. (2023) · IEEE Transportation Electrification Conference and Expo · doi:10.1109/itec55900.2023.10186993
“Furthermore, other components such as capacitors, control boards, and contactors can also have failures that can lead to converter system non-operation [27].”
Background2023 Index Proceedings of the IEEE Vol.111
(2023) · Proceedings of the IEEE · doi:10.1109/jproc.2023.3345570
Design of High Power On Board Charger used for Charging of Electric Vehicle
Khorge, S., Gawande, S. P., Chaturvedi, P., Bonde, A. D., Sheikh, S., & Deshmukh, S. M. (2023) · IEEE International Conference on Smart Technologies for Power, Energy and Control (STPEC) · doi:10.1109/stpec59253.2023.10431125
“1 below illustrates a block diagram of typical electrical power system architecture that can be found in general electric based vehicle [9].”
BackgroundWei, X., Wang, Z., Yao, B., Liu, J., Peng, Y., & Wang, H. (2024) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec48139.2024.10509442 · Cited by 1
“To achieve high operating power, current automotive power semiconductor module commonly uses insulated-gate bipolar transistors (IGBTs), which are expected to be replaced by silicon carbide (SiC) and gallium nitride (GaN) devices in the future to further reduce power loss and system size [19]–[21].”
BackgroundSelf-citationZheng, R., Chen, L., Wang, C., et al. (2024) · Asia Conference on Power and Electrical Engineering (ACPEE) · doi:10.1109/acpee60788.2024.10532540
“The example based on the IEEE33-node distribution network system, nodes 8 and 12 are configured with photovoltaic and wind turbines, nodes 9, 18 and 31 are configured with reactive power compensation devices, nodes 3, 14 and 29 are set as demand response resources for electric storage, and nodes 6,…”
BackgroundMethodSelf-citationCapacitor-Less Buck Converter Using Integrated Planar Electromagnetic Components
Kanakri, H. M., dos Santos, E. C., & Rizkalla, M. (2024) · IEEE Transportation Electrification Conference and Expo · doi:10.1109/itec60657.2024.10599023
“The power electronic converters utilized in electric vehicles (EVs) and hybrid EVs (HEVs) necessitate high degree of reliability [20].”
BackgroundMethodInfluentialSingh, S., Dwivedi, D., Soni, S., Saket, R. K., & Kothari, D. P. (2024) · Wiley eBooks · doi:10.1002/9781394226771.ch22
Automatized Multi-objective Optimization for Reliability of Power Electronics
Debreceni, T., Darázs, B. D., Freitag, C., & Garai, B. (2024) · Electronic System-Integration Technology Conference (ESTC) · doi:10.1109/estc60143.2024.10712033
“From the passives in the HV power loop, the DC-link capacitors are the most sensitive and reliability-critical components [2], [5], [7], [18], [19], [21].”
BackgroundModelling of PV Based Electric Vehicle Charger with V2G Capability
Rao, G. S., Pabbathi, P., & Devadasu, G. (2024) · International Conference on Computational Intelligence for Green and Sustainable Technologies (ICCIGST) · doi:10.1109/iccigst60741.2024.10717577
“The literature [14] has presented a single stage converter with a basic design and few components, but operating the drive motor efficiently presents challenges for the single stage converter.”
BackgroundEXPLORING ELECTROMECHANICAL SYSTEMS IN THE DEVELOPMENT OF NEXT-GENERATION ELECTRIC POWERTRAINS
STOZHOK, O. O. (2024) · Вісник Херсонського національного технічного університету · doi:10.35546/kntu2078-4481.2024.3.17
“[4, 7, 10, 13] In contemporary electric vehicles, the application of these thermal management techniques is critical to the overall performance and durability of the powertrain.”
Comprehensive analysis on electric vehicle technology
Gawande, S. P., Khorge, S., Srivastava, R. K., Dhapodkar, N., & Deshmukh, S. M. (2024) · AIP conference proceedings · doi:10.1063/5.0240210
Reliability Assessment of Power Modules Across Mission Phases in Electric Aircraft Propulsion
Kugener, J., & Kazula, S. (2024) · IEEE International Conference on Electrical Systems for Aircraft, Railway, Ship Propulsion and Road Vehicles & International Transportation Electrification Conference (ESARS-ITEC) · doi:10.1109/esars-itec60450.2024.10819907 · Cited by 1
A mobile charging pile deployment strategy based on Stackelberg game
Huang, X., Wen, P., Duan, J., et al. (2024) · International Conference on New Energy and Power Engineering (ICNEPE) · doi:10.1109/icnepe64067.2024.10860499
Metadata
- Authors
- Blaabjerg, F., Wang, H., Vernica, I., Liu, B., & Davari, P.
- Affiliations
- Aalborg University (DK)
- Venue
- Proceedings of the IEEE
- Published
- 2021-06
- Volume
- 109
- Issue
- 6
- Pages
- 1060-1076
- ISSN
- 0018-9219 (ISSN-L)
- 1558-2256
- OpenAlex
- W3095570029
- Cited by
- 249
- References
- 88
- Citations by year
- 2026: 35 · 2025: 57 · 2024: 67 · 2023: 52 · 2022: 23 · 2021: 15
- FWCI
- 7.72
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Locations
- Proceedings of the IEEE (publishedVersion, cc-by)
- VBN Forskningsportal (Aalborg Universitet) (publishedVersion, cc-by)
- Funders
- VILLUM FONDEN under the VILLUM Investigators (00016591)
- Innovation Fund Denmark through the Advanced Power Electronic Technology and Tools Project
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Silicon Carbide Semiconductor Technologies
- Physical Sciences › Engineering › Automotive Engineering › Electric and Hybrid Vehicle Technologies
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Electric Power Systems and Control
- Keywords
- power electronics reliability, electric vehicles, hybrid electric vehicles, reliability requirements, power electronic components, reliability-oriented design, on-board charger, inverter, vehicle electrification
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.