Reliability of Power Electronic Systems for EV/HEV Applications
Open accessThe DOI matches its Crossref record; 85 of the 88 references it cites were found in a registry or an index; 4 of the 45 sources its claims cite were checked for support.
Abstract
The electrification of the transportation sector is moving on at a fast pace. All car manufacturers have strong programs to electrify their car fleet to fulfill the demands of society and customers by offering carbon-neutral technologies to bring goods and persons from one location to another. Power electronics technology is, in this evolution, essential and also in a rapid development technology-wise. Some of the introduced technologies are quite mature, and the systems designed must have high reliability as they can be quite complicated from an electrical perspective. Therefore, this article focuses on the reliability of the used power electronic systems applied in electric vehicles (EVs) and hybrid EVs (HEVs). It introduces the reliability requirements and challenges given for the power electronics applied in EV/HEV applications. Then, the advances in power electronic components to address the reliability challenges are introduced as they individually contribute to the overall system reliability. The reliability-oriented design methodology is also discussed, including two examples: an EV onboard charger and the drive train inverter. Finally, an outlook in terms of research opportunities in power electronics reliability related to EV/HEVs is provided. It can be concluded that many topics are already well handled in terms of reliability, but issues related to complete new technology introduction are important to keep the focus on.
Overview
CoChat Summary
TL;DR
This article reviews reliability requirements, challenges, component advances, and reliability-oriented design for power electronics in EV/HEV applications. It demonstrates mission-profile-based lifetime assessment for a traction inverter and an onboard charger, finding very low predicted failure probabilities before a 600,000-km service target but noting substantial modeling uncertainties.
Key findings
- Automotive reliability requirements are severe: expected operating life >10 years, ambient temperature range −55 °C to 150 °C, and zero acceptable failure rate; temperature is the major stressor (55% of stress conditions in Table 1), with active thermal cycles ΔTj ≥ 100 °C.
- In the drive-train case, a 75-kW PMSM/330-V battery/400-A, 650-V IGBT module under an EUDC profile gives B0.001 lifetimes of approximately 500,000–1,300,000 km for the transistor and 600,000–1,500,000 km for the diode (90% CI); at the 600,000-km target, failure probability is approximately 0.0004% for the transistor, 0.0002% for the diode, and 0.004% for the entire power module.
- In the OBC case, a 560-µF/400-V dc-link capacitor in a 3.3-kW single-phase OBC has a B1 lifetime of approximately 500,000–2,500,000 km (90% CI), with approximately 0.025% probability of failure before 600,000 km.
- Component advances include reports that SiC MOSFETs with conventional packaging have lower power cycling capability than Si IGBTs, next-generation automotive modules expected to reach 175 °C, and CeraLink capacitors maintaining performance up to 150 °C.
Methods
- The article is a review plus case studies using a six-step mission-profile-based reliability assessment: driving cycle and ambient conditions → mechanical power → electrical loading → electrothermal modeling → empirical lifetime models → reliability block diagram system-level reliability.
- Case studies cover an EV drive train (75-kW PMSM, 330-V battery, 400-A/650-V IGBT module, EUDC mission profile) and a 3.3-kW single-phase OBC (560-µF/400-V dc-link capacitor, standard charging profile), using Rainflow counting, the LESIT lifetime model, Weibull shape parameter β = 3, Monte Carlo simulation with 5% lifetime-coefficient variation, and 90% confidence intervals.
- Thermal modeling uses junction-to-case temperature only; the coolant temperature is assumed to be 75 °C because outer thermal-network information was limited.
Limitations
- Stated: reliability results are subject to uncertainties from environmental mission profiles, electrothermal modeling, and lifetime models, and the error margins can significantly reduce confidence in predicted lifetime; due to high uncertainty, the metrics are used for relative benchmarking rather than as direct lifetime indicators.
- Stated: vibration, dust, and contamination are not considered because of a lack of empirical lifetime models; software failures and battery technology are excluded, and the focus is limited to thermal-related wear-out of power semiconductors and capacitors.
- Stated/evident: the lack of publicly available empirical lifetime models for automotive-qualified IGBT modules led to use of the LESIT model at B10 lifetime with 50% confidence and extrapolation to lower failure probabilities; modeling only junction-to-case temperature with an assumed 75 °C coolant further limits thermal representation.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures




![Fig. 5 R&D and lifetime requirements in EV/HEV. (a) Power electronics R&D development roadmap for electric-based vehicles based on the reports in [38] and [39]. (b) Automotive lifetime requirements based on [39], * [40], ** [38], and *** [41].](https://figures.cochat.ai/paper-figures/16b2b895451544858b0fc9e372c6aefa/reliability-of-power-electronic-systems-for-ev-hev-applications-figure-5.png)
![Fig. 6 Advances in packaging elements for power modules [18].](https://figures.cochat.ai/paper-figures/41a8f71cf76147d9b1432b384fc74271/reliability-of-power-electronic-systems-for-ev-hev-applications-figure-6.png)

![Fig. 8 Typical operational mission profiles for the two subassemblies. (a) Electric vehicle driving cycle [80]. (b) Scaled-down power demand for an EV OBC (based on [81]).](https://figures.cochat.ai/paper-figures/68c177e618b44bcb9d952857c7b98b4a/reliability-of-power-electronic-systems-for-ev-hev-applications-figure-8.png)










Verification
Claims the paper makes
1 Valid · 9 Not valid · 32 Not checked · 46 Own results and interpretations
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“Besides, the ambient temperature under the hood could be as high as 100 ◦ C with high humidity [77].”
What the sources say
- Could not verifycites [77] sourceExperimental — accuracy not yet measured
The Thermal Model section treats ambient temperature as a constant model input, but does not describe conditions under a vehicle hood. Searches for 100°C ambient temperature, under-hood conditions, and humidity found no passage supporting the claimed temperature or humidity. (LLM, conf=0.74)
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“Therefore, advanced cooling technologies, such as spray cooling and jet impingement, are developed to meet the demands of the automotive industry [79].”
What the sources say
- Could not verifycites [79] sourceExperimental — accuracy not yet measured
The Introduction discusses temperature-related reliability, and Section II mentions a coolant loop for a telecom backup fuel-cell system; neither addresses automotive cooling technologies. Searches for spray cooling, jet impingement, and automotive thermal management found no passage supporting the claim. Page numbers were unavailable in our copy. (LLM, conf=0.76)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“the dc-link capacitor of the OBC has a 1% probability of failure between 500 000 and 2 500 000 km, with a 90% confidence interval.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 2 assumptions not shown here.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“However, as shown in Table 2, there is a lack of qualification standards for power semiconductor modules.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
None of the sources cited for this claim have been checked yet.
In the paper
“As can be seen from the table, temperature stress is a major stressor that destroys power electronic components.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
33 more claims
Create a free account to see all 88 claims and to verify the 2 references still open.
- Probably not a substantial claim. 42
- It may state two separate claims as one. 16
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ III. A D V A N C E S I N P O W E R E L E C T R O N I C C O M P O N E N T S T O A D D R E S S R E L I A B I L I T Y C H A L L E N G E S · p. 7
“this article focuses on the advances in power modules and capacitors only in Section III”
§ C. Cooling Assemblies and Concepts · p. 9
“## C. Cooling Assemblies and Concepts”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ B. Reliability Analysis of an Electric Vehicle Case Study · p. 10
“The overall topology configurations of the electrical drive train main inverter and the onboard EV charger for the two selected subassemblies are shown in Figs. 3 and 5, respectively.”
§ A. Power Modules · p. 8
“Fig. 5. R&D and lifetime requirements in EV/HEV.”
Citations
Cites
An Industry-Based Survey of Reliability in Power Electronic Converters
Yang, S., Bryant, A., Mawby, P., Xiang, D., Ran, L., & Tavner, P. (2011) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2011.2124436 · Cited by 2,019
Handbook of software reliability engineering
Lyu, M. R.-T. (1996) · McGraw-Hill, Inc. eBooks · Cited by 1,592
Electrical Machines and Drives for Electric, Hybrid, and Fuel Cell Vehicles
Zhu, Z. Q., & Howe, D. (2007) · Proceedings of the IEEE · doi:10.1109/jproc.2006.892482 · Cited by 1,547 · cited 1×
“Intensive research and development are currently going on enhancing PM EMs and adopting different types of EMs in order to further improve the performance of future electric-based vehicles [48].”
MethodEmadi, A., Lee, Y. J., & Rajashekara, K. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.922768 · Cited by 1,461 · cited 1×
“Notably, different possible configurations for the power train in EV/HEV can be found in the automotive market [25]–[28].”
BackgroundReliability of Capacitors for DC-Link Applications in Power Electronic Converters—An Overview
Wang, H., & Blaabjerg, F. (2014) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2014.2308357 · Cited by 1,384 · cited 3×
“Besides active components, the capacitor reliability is also essential to understand and take into consideration when doing reliability analysis for the complete system [20].”
BackgroundInfluentialSelf-citationModern Electric, Hybrid Electric, and Fuel Cell Vehicles: Fundamentals, Theory, and Design
Ehsani, M., Gao, Y., Gay, S. E., & Emadi, A. (2004) · CRC Press eBooks · doi:10.1201/9781420037739 · Cited by 1,248
Closed-loop optimization of fast-charging protocols for batteries with machine learning
Attia, P. M., Grover, A., Jin, N., Severson, K. A., Markov, T. M., Liao, Y.-H., Chen, M. H., Cheong, B., Perkins, N., Yang, Z., et al. (2020) · Nature · doi:10.1038/s41586-020-1994-5 · Cited by 1,180
Toward Reliable Power Electronics: Challenges, Design Tools, and Opportunities
Wang, H., Liserre, M., & Blaabjerg, F. (2013) · IEEE Industrial Electronics Magazine · doi:10.1109/mie.2013.2252958 · Cited by 916 · cited 1×
“knowledge base (physics of failure), a design stage (DfR and robustness validation), and an operational phase (intelligent control and condition monitoring) [10]–[12].”
BackgroundSelf-citationThe Essence of Three-Phase PFC Rectifier Systems—Part I
Kolar, J. W., & Friedli, T. (2013) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2012.2197867 · Cited by 788 · cited 1×
“Notably, depending on the topology, the HV dc bus voltage will be different [32], [33].”
BackgroundPractical Reliability Engineering
O'Connor, P. D. T., & Kleyner, A. (2011) · Wiley eBooks · doi:10.1002/9781119961260 · Cited by 783
Research works printed but not linked: 21
- 2018, The Roadmap Report Towards 2040 A Guide to Automotive Propulsion Technologies
- 2018, Shaping Future Electromobility With Semiconductor Innovations
- 2015, Handbook for Robustness Validation of Semiconductor Devices in Automotive Applications
- ehsani, 2018, Modern Electric Hybrid Electric and Fuel Cell Vehicles
- drexhage, 2016, Effect of humidity and condensation on power electronics systems
- 2013, Electric and Electronic Components in Motor Vehicles up to 3 5t
- 2020, Electric vehicle outlook 2020
- 2013, Failure Mechanism Based Stress Test Qualification for Discrete Semiconductors in Automotive Applications REV D1
- 2017, Electrical and electronics technical team roadmap
- 2008, Vorlesung Qualtat und Zuverlassigkeit von Fahrzeug e/e Hardware an der tu Berlin
- 2010, Stress Test Qualification for Passive Components
- 2013, Zvei Die Elektroindustrie Handbook for Robustness Validation of Automotive Electrical/Electronic Modules
- allouche, 2020, Hitachi DSC Power Module From Audi e-Tron Inverter
- christmann, 2009, Reliability of power modules in hybrid vehicles, Proc PCIM Eur, 359
- 2019, Qualification of Power Modules for Use in Power Electron Converter Units in Motor Vehicles
- ishihara, 2012, New transfer-mold power module series for automotive power-train inverters, Proc PCIM Eur, 1408
- ishihara, 2014, New compact-package power modules for electric and hybrid vehicles (J1 series), Proc PCIM Eur, 1093
- kimura, 2014, High-power-density inverter technology for hybrid and electric vehicle applications, Hitachi Rev, 63, 41
- knappik, 2019, The advantages of 48-volt vehicle electronics, Veh Technol
- 2005, Standard Practices for Cycle Counting in Fatigue Analysis
- wintrich, 2015, Application Manual Power Semiconductors
Cited by
Items 201–241 of 241
Abu-Rub, O. H., Sharida, A., Saeedifard, M., et al. (2024) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce55643.2024.10861757
Novel Current-Sensorless Control Approach for Single-Stage Buck-Boost Based EV charger
Sharida, A., Bayhan, S., & Abu‐Rub, H. (2024) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon55916.2024.10905680
“The key requirements for these chargers include high efficiency, reliability, and power factor correction (PFC) functionality [2].”
Lei, W., Wang, L., Nie, W., & Zhang, X. (2025) · Lecture notes in electrical engineering · doi:10.1007/978-981-96-4063-8_11
Salim, M., & Safarzadeh, O. (2025) · International Transactions on Electrical Energy Systems · doi:10.1155/etep/5034005 · Cited by 1
“Consequently, understanding the reliability and lifetime estimation of EVs, along with evaluating the reliability issues in PEs, is notable for advancing EV development and adoption [25, 26].”
Wu, Y., Choksi, K., Defaz, S., et al. (2025) · IEEE Applied Power Electronics Conference and Exposition (APEC) · doi:10.1109/apec48143.2025.10977297
Reliability and Efficiency Analysis of Liquid Cooling for Lithium-Ion Batteries in Electric Vehicles
Rabbani, E., Husain, S., Ashfaq, H., & Asjad, M. (2024) · International BIT Conference (BITCON) · doi:10.1109/bitcon63716.2024.10985255
“In India, hybrid EVs are becoming more popular because to their lower emissions and fuel efficiency [10-13].”
InfluentialReliability-Oriented Fast Charging Strategies for Lithium-Ion Batteries and EV Chargers
Tahir, M. U. (2025) · VBN Forskningsportal (Aalborg Universitet) · doi:10.54337/aau785715319
Çelık, D., & Meral, M. E. (2025) · Measurement · doi:10.1016/j.measurement.2025.118971
Scimone, T., Tornello, L. D., Scelba, G., et al. (2025) · doi:10.1109/sdemped53223.2025.11154344
Monitoring the degradation of SiC MOSFETs undergoing thermo-mechanical stresses
Molenaar, M., Shekhar, A., & Bauer, P. (2025) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon58223.2025.11221296 · Cited by 2
Single-Phase Single-Stage NPC AC-DC Converter Applied as Electric Vehicle Battery Charger
de Souza, J. J. S., Mazza, L. C. D. S., Lima, W. D. S., Barbosa, S. G., & Antunes, F. L. M. (2025) · Brazilian Power Electronics Conference (COBEP) · doi:10.1109/cobep66423.2025.11231511
“Thus, the electrification of the transport sector, along with the use of smart grids, is necessary to reduce the emission of polluting gases, leading to an intensified investigation and improvement of battery electric vehicles (EV's) or plug-in hybrid electric vehicles (PHEV's) [1][2].”
He, Y., Wang, L., Yin, Z., et al. (2025) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2025.3637103
“Manufacturers’ surveys identify semiconductor devices as the most critical and susceptible components in industrial power electronics systems, with temperature-related failures accounting for the majority of issues [9].”
Circuit-to-Graph: Power Converters Modeling With Multidimensional Generalization
Lei, W., Lin, F., Zhang, X., et al. (2025) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2025.3637228
“…energy systems, power converters are widely used in modern electrical facilities such as renewable energy power generation [1], electric vehicle drive systems [2], and wireless power transfer [3] due to their e ffi cient energy conversion performance and excellent dynamic response capabilities.”
Colvero, G. D., Murillo-Yarce, D., Tuñón, J., et al. (2025) · doi:10.1109/ecce-europe62795.2025.11238508
“The on-board battery, a key component of the EV electrical system, directly impacts vehicle performance, range, and energy efficiency [1].”
Fault Diagnosis and Prediction of Electric Vehicle Drive using Support Vector Machine Algorithm
Kumar, M. P., Velpula, S., Saiprakash, C., & Sahoo, B. (2025) · IEEE International Conference on Sustainable Energy and Future Electric Transportation (SEFET) · doi:10.1109/sefet65155.2025.11255357 · Cited by 1
“Power electronic converters are crucial in adjustable-speed drives, power quality correction, renewable energy interfaces, energy storage, and EVs, providing compact, efficient solutions but raising reliability challenges [29].”
Ryu, T., Choi, U., Kim, M. K., & Lim, J. (2025) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce58356.2025.11260101
“However, their reliability is still a crucial issue in power electronic systems [3], [4].”
Li, T.-H., Zaghari, P., Wang, Y.-J., et al. (2025) · International Microsystems, Packaging, Assembly and Circuits Technology Conference · doi:10.1109/impact67645.2025.11281709
Schmalzl, S., von Bonin, M., Frey, M., Gauterin, F., & Braun, M. (2025) · SSRN Electronic Journal · doi:10.2139/ssrn.5955624
Yang, G., & Kim, J. (2025) · International Conference on Electrical Machines and Systems (ICEMS) · doi:10.23919/icems66262.2025.11317029
“…particularly in electric vehicles (EVs) and energy storage systems (ESS)[1], which play a crucial role in decarbonization and grid stability, the need for reliable and real-time state monitoring technologies has become increasingly critical to ensure safety and operational stability[2].”
Rachna, & Singh, A. K. (2026) · Journal of Power Sources · doi:10.1016/j.jpowsour.2026.239283
A Resilient, Optimization-Based Framework for Starting Networks With Integrated Power Electronics
Starke, M. R., Dean, B., Kim, N., Campbell, S. L., Moorthy, R. S. K., Pinto, J. O. P., & Chinthavali, M. (2026) · IEEE Open Journal of Industry Applications · doi:10.1109/ojia.2026.3658884
“Failure in elements like the power stack, capacitors, control boards, and/or contactors can also cause the converter system to become inoperable [40], [41], [42].”
Battaglia, V. L., Pinto, L. D., Marini, S., et al. (2026) · Designs · doi:10.3390/designs10010017
Zhu, S., Guan, J., Sun, X., Guo, X., Chen, C., & Kang, Y. (2026) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2026.3665330
Enhancing Overload Capability of Electric Truck Inverters via Active Thermal Control
Agirrezabala, E., Pascal, Y., Debbadi, K., Liserre, M., Aizpuru, I., & Garrido, D. (2025) · IEEE Vehicle Power and Propulsion Conference (VPPC) · doi:10.1109/vppc66000.2025.11392945 · Cited by 1
Schmidt, H., Käß, M., Lichtinger, R., Hülsebrock, M., Atzrodt, H., & Bein, T. (2026) · Reliability Engineering & System Safety · doi:10.1016/j.ress.2026.112534
A Thermal Model Considering the Effective Heat Conduction Path in IGBT Module
Du, M., Li, Q., Wang, G., et al. (2026) · Journal of Thermal Science and Engineering Applications · doi:10.1115/1.4071542
Al-Hysam, A., Ali, Z. H., Alaküla, M., & Raisz, D. (2026) · e-Prime – Nexus of Electrical Electronic and Intelligent Engineering · doi:10.1016/j.eprime.2026.201181
Boretti, A. A. (2026) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2026.131257
Islam, M. M. F., Lopes, M. F., Jahangir, J. B., Lee, W., & Alam, M. A. (2026) · IEEE International Reliability Physics Symposium proceedings · doi:10.1109/irps61424.2026.11499268
“Among power-converter components, MOSFETs and capacitors represent the dominant reliability bottlenecks, accounting for a significant fraction of observed failures due to their sensitivity to coupled electrical and thermal stresses as depicted in Figure 1 [11].”
An Integrated Physics-Based Reliability Modeling of Power Converters with Degradation Feedback
Lopes, M. F., Islam, M. M. F., Lee, S., Lee, W., & Alam, M. A. (2026) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec51134.2026.11517194
Inverse Model Predictive Control for Bidirectional Power Flow in Wireless EV Charging Systems
Alvarez-Duque, M., Gil-González, W. J., & Escobar-Mejía, A. (2026) · doi:10.1109/cpeee69412.2026.11521447
“Despite continuous advances in lithium-ion battery technology, the achievable driving range remains limited compared to conventional internal combustion vehicles, while charging periods are still significantly longer than refueling periods for gasoline-powered vehicles [1], [2].”
Sakhare, A., Mikkili, S., & Bonthagorla, P. K. (2026) · IET Electrical Systems in Transportation · doi:10.1049/els2/9670895 · Cited by 1
Akkus, M., Akboy, E., & Boynueğri, A. R. (2026) · Turkish Journal of Electrical Power and Energy Systems · doi:10.67047/tepes.1892878
Kulkarni, V., Bürger, F., Perrin, L., Kospach, A., & Volkwein, S. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.7010234
Chen, W. C., Lin, Y., Li, Z. G., & Fan, Y. (2026) · Microelectronics International · doi:10.1108/mi-01-2026-0005
Reliability estimation of Smart TV application using Markov process
Tyagi, V., Singh, S., Kaushik, S., et al. (2026) · Life Cycle Reliability and Safety Engineering · doi:10.1007/s41872-026-00431-z
Tsang, B., Shah, S. B., Jeremy, J., et al. (2026) · doi:10.1109/iteceats66641.2026.11592844
“Thus, rigorous and exhaustive testing under a wide range of electrical and environmental conditions is mandatory throughout a PEC’s design cycle [2].”
Anazawa, M., & Kusaka, K. (2026) · International Power Electronics Conference (IPEC) · doi:10.23919/ipec-nagasaki2026-ec64663.2026.11597512
“The reliability of these power converters is a key concern [1–3], especially in industrial applications requiring long-term operation, such as photovoltaic systems [4] and electric vehicles (EVs) [5].”
Olubamiwa, O. I., Botha, S., Gule, N., Alatise, O. M., & Akuru, U. B. (2026) · Sustainability · doi:10.3390/su18178838
Górecki, K., & Detka, K. (2026) · Energies · doi:10.3390/en19184328
Chaisit, P., Arpanutud, K., & Supatti, U. (2026) · International Electrical Engineering Congress (iEECON) · doi:10.1109/ieecon68065.2026.11707139
“[1].”
Metadata
- Authors
- Blaabjerg, F., Wang, H., Vernica, I., Liu, B., & Davari, P.
- Affiliations
- Aalborg University (DK)
- Venue
- Proceedings of the IEEE
- Published
- 2021-06
- Volume
- 109
- Issue
- 6
- Pages
- 1060-1076
- ISSN
- 0018-9219 (ISSN-L)
- 1558-2256
- OpenAlex
- W3095570029
- Cited by
- 249
- References
- 88
- Citations by year
- 2026: 35 · 2025: 57 · 2024: 67 · 2023: 52 · 2022: 23 · 2021: 15
- FWCI
- 7.72
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Locations
- Proceedings of the IEEE (publishedVersion, cc-by)
- VBN Forskningsportal (Aalborg Universitet) (publishedVersion, cc-by)
- Funders
- VILLUM FONDEN under the VILLUM Investigators (00016591)
- Innovation Fund Denmark through the Advanced Power Electronic Technology and Tools Project
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Silicon Carbide Semiconductor Technologies
- Physical Sciences › Engineering › Automotive Engineering › Electric and Hybrid Vehicle Technologies
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Electric Power Systems and Control
- Keywords
- power electronics reliability, electric vehicles, hybrid electric vehicles, reliability requirements, power electronic components, reliability-oriented design, on-board charger, inverter, vehicle electrification
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.