Transient Thermal Performance of IGBT Power Modules Attached by Low-Temperature Sintered Nanosilver
The DOI matches its Crossref record; 19 of the 20 references it cites were found in a registry or an index.
Abstract
Recently, to accurately study the transient thermal behavior of power modules, a transient thermal measurement system was developed to investigate the transient thermal behavior of insulated-gate bipolar transistor (IGBT) modules attached by nanosilver paste and two kinds of lead-free solders. We found that the transient thermal impedance of IGBT modules attached by nanosilver paste was 9% lower than that of the modules using SAC305 and SN100C with 40-ms heating pulse. In addition, finite-element analysis is employed to simulate thermal performance of the IGBT devices. The simulation shows that the transient thermal impedance of IGBT modules attached by nanosilver paste was also lower than that of the modules using lead-free solders. A convenient way was introduced to well predict the transient thermal behavior of IGBT power module. The calculated results agreed well with the measured one. The interface thermal impedance of sintered nanosilver and SNC100C are calculated to be 0.011 ~ 0.031 K/W and 0.022 ~ 0.042 K/W, respectively.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“Silver-sintered joints provide excellent electrical/thermal conductivity and high-temperature stability but face electromigration (EM) and cost challenges [2,30-35].”
From Thermal Management of Wide-Bandgap Power Semiconductors: Strategies and Challenges in SiC and GaN Power Devices (2025) · cites this paper as [32]
In the citing paper
“IMC growth is often accelerated by microstructural defects at the solder interface (e.g., grain boundaries, oxides, interfacial roughness), which act as heterogeneous nucleation sites; in addition, unbalanced Cu/Sn interdiffusion can induce Kirkendall voiding, degrading thermo-mechanical integrity over life [30,32].”
From Thermal Management of Wide-Bandgap Power Semiconductors: Strategies and Challenges in SiC and GaN Power Devices (2025) · cites this paper as [32]
In the citing paper
“IMC growth is often accelerated by microstructural defects at the solder interface (e.g., grain boundaries, oxides, interfacial roughness), which act as heterogeneous nucleation sites; in addition, unbalanced Cu/Sn interdiffusion can induce Kirkendall voiding, degrading thermo-mechanical integrity over life [30,32].”
From Thermal Management of Wide-Bandgap Power Semiconductors: Strategies and Challenges in SiC and GaN Power Devices (2025) · cites this paper as [32]
Citations
Cites
Physics of Semiconductor Devices
(2002) · Kluwer Academic Publishers eBooks · doi:10.1007/b117561 · Cited by 13,963
Physics of Semiconductor Devices: Proceedings of the Fourth International Workshop
JAIN, S. C., & RADHAKRISHNA, S. (1987) · Physics of Semiconductor Devices · doi:10.1142/9789814542012 · Cited by 4,151
Fundamentals of Power Semiconductor Devices
Baliga, B. J. (2008) · Springer eBooks · doi:10.1007/978-0-387-47314-7 · Cited by 2,174
Bai, J. G., Zhang, Z. Z., Calata, J. N., & Lu, G.-Q. (2006) · IEEE Transactions on Components and Packaging Technologies · doi:10.1109/tcapt.2005.853167 · Cited by 375
Self-citationLow-Temperature Sintering with Nano-Silver Paste in Die-Attached Interconnection
Wang, T., Chen, X., Lu, G.-Q., & Lei, G.-Y. (2007) · Journal of Electronic Materials · doi:10.1007/s11664-007-0230-5 · Cited by 345
Self-citationBai, J. G., & Lu, G.-Q. (2006) · IEEE Transactions on Device and Materials Reliability · doi:10.1109/tdmr.2006.882196 · Cited by 214
Self-citationLu, G., Calata, J. N., Zhang, Z., & Bai, J. G. (2004) · International Symposium on High Density packaging and Microsystem Integration · doi:10.1109/hpd.2004.1346671 · Cited by 93
Self-citationPower Electronics Cooling Effectiveness Versus Thermal Inertia
Meysenc, L., Jylhakallio, M., & Barbosa, P. (2005) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2005.846548 · Cited by 64
Important properties of transient thermal impedance for MOS-gated power semiconductors
Jakopovic, Z., Benčić, Z., & Kolonić, F. (2003) · IEEE International Symposium on Industrial Electronics (ISIE) · doi:10.1109/isie.1999.798675 · Cited by 40
Shaw, M. C., Waldrop, J. R., Chandrasekaran, S., Kagalwala, B., Jing, X., Brown, E. R., Dhir, V. J., & Fabbeo, M. (2003) · ITherm 2002. Eighth Intersociety Conference on Thermal and Thermomechanical Phenomena in Electronic Systems (Cat. No.02CH37258) · doi:10.1109/itherm.2002.1012567 · Cited by 39
Research works printed but not linked: 2
- zarebski, 1993, Thermal transients in bipolar transistors: Measurements and simulations, Malta Proc Int Conf Inf Syst Methods Appl Eng Probl, 111
- mantooth, 2006, Emerging capabilities in electronics technologies for extreme environments. Part I—High temperature electronics, IEEE Power Electron Soc Newsl, 18, 9
Cited by
Joining of Silver Nanomaterials at Low Temperatures: Processes, Properties, and Applications
Peng, P., Hu, A., Gerlich, A. P., Zou, G., Liu, L., & Zhou, Y. N. (2015) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.5b02134 · Cited by 364
Thermal Management on IGBT Power Electronic Devices and Modules
Qian, C., Gheitaghy, A. M., Fan, J., Tang, H., Sun, B., Ye, H., & Zhang, G. (2018) · IEEE Access · doi:10.1109/access.2018.2793300 · Cited by 342
Ji, B., Pickert, V., Cao, W., & Zahawi, B. (2013) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2013.2251358 · Cited by 329
Ji, B., Song, X., Sciberras, E. A., Cao, W., Hu, Y., & Pickert, V. (2014) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2014.2365531 · Cited by 160
A Temperature-Dependent Thermal Model of IGBT Modules Suitable for Circuit-Level Simulations
Wu, R., Wang, H., Pedersen, K. B., Ma, K., Ghimire, P., Iannuzzo, F., & Blaabjerg, F. (2016) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2016.2540614 · Cited by 125
Chen, C., Nagao, S., Zhang, H., Jiu, J., Sugahara, T., Suganuma, K., Iwashige, T., Sugiura, K., & Tsuruta, K. (2016) · Journal of Electronic Materials · doi:10.1007/s11664-016-5200-3 · Cited by 104
Chen, G., Zhang, Z., Mei, Y., Li, X., Yu, D., Wang, L., & Chen, X. (2014) · Mechanics of Materials · doi:10.1016/j.mechmat.2014.02.001 · Cited by 77
Self-citationWang, M., Mei, Y., Liu, W., Xie, Y., Fu, S., Li, X., & Lu, G. (2019) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2019.2920254 · Cited by 73
Self-citationSimplification of Low-Temperature Sintering Nanosilver for Power Electronics Packaging
Mei, Y., Chen, G., Cao, Y., Li, X., Han, D., & Chen, X. (2013) · Journal of Electronic Materials · doi:10.1007/s11664-013-2561-8 · Cited by 65
Self-citationFu, S., Mei, Y., Li, X., Ma, C., & Lu, G. (2016) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2016.2619118 · Cited by 59
Self-citationZhang, R., Cai, J., Wang, Q., Li, J., Hu, Y., Du, H., & Li, L. (2014) · Journal of Electronic Packaging · doi:10.1115/1.4026616 · Cited by 49
Xu, L., Liu, Y., & Liu, S. (2014) · Microelectronics Reliability · doi:10.1016/j.microrel.2014.07.053 · Cited by 48
Silver nanopaste: Synthesis, reinforcements and application
Zhang, P., Jiang, X., Yuan, P., Yan, H., & Yang, D. (2018) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.06.083 · Cited by 47
Novel interface material used in high power electronic die-attaching on bare Cu substrates
Zhao, S.-Y., Li, X., Mei, Y., & Lu, G. (2016) · Journal of Materials Science Materials in Electronics · doi:10.1007/s10854-016-5208-8 · Cited by 47
Self-citationThermal Concept Design of MOSFET Power Modules in Inverter Subsystems for Electric Vehicles
Karimi, D., Behi, H., Jaguemont, J., Baghdadi, M. E., Mierlo, J. V., & Hegazy, O. (2019) · International Conference on Power and Energy Systems (ICPES) · doi:10.1109/icpes47639.2019.9105437 · Cited by 46
A temperature-dependent thermal model of IGBT modules suitable for circuit-level simulations
Wu, R. L., Wang, H., Ma, K., Ghimire, P., Iannuzzo, F., & Blaabjerg, F. (2014) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2014.6953793 · Cited by 41
Huang, X., Wang, Y., Zhu, Q., Du, Z., Zhou, L., & Liu, H. (2023) · Engineering Failure Analysis · doi:10.1016/j.engfailanal.2023.107625 · Cited by 41
Li, W., Wu, T., Jiao, R., Zhang, B., Li, S., Zhou, Y., & Li, L. (2014) · Colloids and Surfaces A Physicochemical and Engineering Aspects · doi:10.1016/j.colsurfa.2014.11.018 · Cited by 41
Thermo-Mechanical Reliability of Double-Sided IGBT Assembly Bonded by Sintered Nanosilver
Mei, Y., Lian, J., Chen, X., Chen, G., Li, X., & Lu, G. (2013) · IEEE Transactions on Device and Materials Reliability · doi:10.1109/tdmr.2013.2280668 · Cited by 36
Self-citationHan, G., Kim, J., Park, S., & Bae, W. (2025) · Electronics · doi:10.3390/electronics14214193 · Cited by 34
“…accelerated by microstructural defects at the solder interface (e.g., grain boundaries, oxides, interfacial roughness), which act as heterogeneous nucleation sites; in addition, unbalanced Cu/Sn interdiffusion can induce Kirkendall voiding, degrading thermo-mechanical integrity over life [30,32].”
Application of STATCOM to improve the LVRT of DFIG during RSC fire-through fault
Abdou, Abu‐Siada, A., & Pota, H. R. (2012) · eSpace (Curtin University) · Cited by 34
Wang, M., Lu, G., Mei, Y., Li, X., Wang, L., & Chen, G. (2015) · IET Power Electronics · doi:10.1049/iet-pel.2014.0120 · Cited by 29
Self-citationCharacterization of Nanosilver Dry Films for High-Temperature Applications
Khazaka, R., Thollin, B., Mendizabal, L., Henry, D., Khazaka, R., & Hanna, R. (2015) · IEEE Transactions on Device and Materials Reliability · doi:10.1109/tdmr.2015.2402294 · Cited by 27
IGBT Junction Temperature Measurements: Inclusive of Dynamic Thermal Parameters
Zhang, J., Du, M., Jing, L., Wei, K., & Hurley, W. G. (2019) · IEEE Transactions on Device and Materials Reliability · doi:10.1109/tdmr.2019.2910182 · Cited by 27
Chen, G., Zhang, Z., Mei, Y., Li, X., Lu, G., & Chen, X. (2013) · Microelectronics Reliability · doi:10.1016/j.microrel.2012.11.011 · Cited by 27
Self-citationTransient thermal measurement on nano-metallic sintered die-attach joints using a thermal test chip
Sattari, R., Hu, D., Liu, X., van Zeijl, H. W., Vollebregt, S., & Zhang, G. (2022) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2022.119503 · Cited by 26
Fatigue Crack Networks in Die-Attach Layers of IGBT Modules Under a Power Cycling Test
Liu, S., Vuorinen, V., Liu, X., Fredrikson, O., Brand, S., Tiwary, N., Lutz, J., & Paulasto‐Kröckel, M. (2024) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2024.3447909 · Cited by 26
Liu, W., Mei, Y., Xie, Y., Wang, M., Li, X., & Lu, G. (2019) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2019.2905773 · Cited by 23
Self-citationLu, G., Yang, W. H., Mei, Y., Li, X., Chen, G., & Chen, X. (2014) · IEEE Transactions on Device and Materials Reliability · doi:10.1109/tdmr.2014.2304737 · Cited by 22
Self-citationLi, C., Sun, X., Zha, M., Yang, C., Wang, W., & Su, J. (2022) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2022.3227334 · Cited by 22
Abdou, A. F., Abu‐Siada, A., & Pota, H. R. (2013) · Journal of Renewable and Sustainable Energy · doi:10.1063/1.4812651 · Cited by 21
Process development and reliability of sintered high power chip size packages and flip chip LEDs
Hanß, A., Schmid, M., Bhogaraju, S. K., Conti, F., & Elger, G. (2018) · International Conference on Electronics Packaging and iMAPS All Asia Conference (ICEP-IAAC) · doi:10.23919/icep.2018.8374351 · Cited by 21
Impact of VSC faults on dynamic performance and low voltage ride through of DFIG
Abdou, A. F., Abu‐Siada, A., & Pota, H. R. (2014) · International Journal of Electrical Power & Energy Systems · doi:10.1016/j.ijepes.2014.10.014 · Cited by 20
Lu, G.-Q., Li, W., Mei, Y., Chen, G., Li, X., & Chen, X. (2014) · IEEE Transactions on Device and Materials Reliability · doi:10.1109/tdmr.2014.2306955 · Cited by 19
Self-citationReliability of Sintered and Soldered High Power Chip Size Packages and Flip Chip LEDs
Hanß, A., Schmid, M., Bhogaraju, S. K., Conti, F., & Elger, G. (2018) · IEEE Electronic Components and Technology Conference (ECTC) · doi:10.1109/ectc.2018.00312 · Cited by 19
Chen, G., & Zhao, X. (2017) · Microelectronics Reliability · doi:10.1016/j.microrel.2017.11.010 · Cited by 18
Self-citationA Multichip Phase-Leg IGBT Module Bonded by Pressureless Sintering of Nanosilver Paste
Fu, S., Mei, Y., Li, X., Ma, C., & Lu, G. (2016) · IEEE Transactions on Device and Materials Reliability · doi:10.1109/tdmr.2016.2633813 · Cited by 15
Self-citationLee, C., Kuo, K.-S., Wang, C.-W., Chang, J., Han, W.-K., & Chang, T. (2020) · Microelectronics Reliability · doi:10.1016/j.microrel.2020.113890 · Cited by 14
A parameter self-correcting thermal network model considering IGBT module solder layer aging
Liu, Y., Du, M., Yin, J., & Dong, C. (2023) · Microelectronics Journal · doi:10.1016/j.mejo.2023.105741 · Cited by 14
Thermal optimization of IGBT modules based on finite element method and particle swarm optimization
Alavi, O., Abdollah, M., & Viki, A. H. (2017) · Journal of Computational Electronics · doi:10.1007/s10825-017-1023-6 · Cited by 14
Reliability and Characterization of Nanosilver Joints Prepared by a Time-Reduced Sintering Process
Dai, J., Li, J., Agyakwa, P. A., Corfield, M. R., & Johnson, C. M. (2021) · IEEE Transactions on Device and Materials Reliability · doi:10.1109/tdmr.2021.3118323 · Cited by 12
Berry, D. W. (2014) · VTechWorks (Virginia Tech) · Cited by 12
Phase field modelling of the electromigration behaviour in sintered silver
Jiang, H., Liang, S., Wei, C. Y., & Ke, C.-B. (2022) · Journal of materials research/Pratt's guide to venture capital sources · doi:10.1557/s43578-022-00635-w · Cited by 12
Multiphysics Model of Microstrip Structure Under High Voltage Pulse Excitation
Ravelo, B. (2018) · IEEE journal on multiscale and multiphysics computational techniques · doi:10.1109/jmmct.2018.2852681 · Cited by 12
Application of STATCOM-HTS to improve DFIG performance and FRT during IGBT short circuit
Abdou, A. F., Pota, H. R., Abu‐Siada, A., & Alharbi, Y. M. (2014) · Australasian Universities Power Engineering Conference · doi:10.1109/aupec.2014.6966641 · Cited by 11
Sintered metal alloy and composite as bonding materials for electronics applications
Wang, W. J., Patra, A., Yong, L. X., Long, X., Jia, Q., Shen, L., & Siow, K. S. (2025) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2025.08.079 · Cited by 11
Ding, Z., Wang, Z., Zhang, B., Lu, G., & Mei, Y. (2022) · Applied Sciences · doi:10.3390/app12094748 · Cited by 11
Self-citationThollin, B., Dupont, L., Khatir, Z., Avenas, Y., Crébier, J.-C., & Jeannin, P. (2013) · European Conference on Power Electronics and Applications · doi:10.1109/epe.2013.6634411 · Cited by 10
Thollin, B., Dupont, L., Avenas, Y., Crébier, J.-C., Khatir, Z., & Jeannin, P. (2016) · IEEE Transactions on Components Packaging and Manufacturing Technology · doi:10.1109/tcpmt.2016.2554538 · Cited by 9
Etude de la fiabilité de modules à base de LEDs blanches pour applications automobile
Chambion, B. (2014) · theses.fr (ABES) · doi:10.70675/a9b44079zbeabz4e5cz8133zc695f57112b5 · Cited by 9
Lu, G., Wang, M., Mei, Y., Li, X., Wang, L., Chen, G., & Chen, X. (2013) · International Conference on Electronic Packaging Technology (ICEPT) · doi:10.1109/icept.2013.6756601 · Cited by 8
Self-citationYang, C., Ren, C., Huang, C., Qiao, Q., Zhang, H., Liu, J., Tian, Y., Pan, J., Li, X., Wei, X., et al. (2025) · High Voltage · doi:10.1049/hve2.12525 · Cited by 7
Reliability Behavior of A Resin-Free Nanosilver Paste at Ultra-Low Temperature of 180°C
Zhang, B., Chen, S., Lu, G., & Mei, Y. (2022) · Power Electronic Devices and Components · doi:10.1016/j.pedc.2022.100014 · Cited by 6
Self-citationMultipoint Thermal Sensing System for Power Semiconductor Devices Utilizing Fiber Bragg Gratings
Isa, R., Iqbal, N., Abido, M. A., Mirza, J., & Qureshi, K. K. (2024) · Applied Sciences · doi:10.3390/app142311328 · Cited by 6
Zhao, S.-Y., Li, X., Mei, Y., & Lu, G. (2015) · International Conference on Electronics Packaging and iMAPS All Asia Conference (ICEP-IAAC) · doi:10.1109/icep-iaac.2015.7111065 · Cited by 6
Self-citationWang, M., Mei, Y., Li, X., & Lu, G.-Q. (2015) · International Conference on Electronics Packaging and iMAPS All Asia Conference (ICEP-IAAC) · doi:10.1109/icep-iaac.2015.7111077 · Cited by 6
Self-citationThollin, B. (2013) · theses.fr (ABES) · doi:10.70675/a3c58aeaz3722z457azbeabzb7c19c7dabe0 · Cited by 5
Tao, M., Mei, Y., Lee, S. W. R., Yun, F., & Lu, G. (2016) · International Conference on Electronic Packaging Technology (ICEPT) · doi:10.1109/icept.2016.7583297 · Cited by 5
Self-citationPower Module Packaging in Automotive Applications
Atelge, M. R. (2016) · UWSpace (University of Waterloo) · Cited by 4
Lu, G., Li, W., Mei, Y., & Li, X. (2014) · International Conference on Electronics Packaging (ICEP) · doi:10.1109/icep.2014.6826737 · Cited by 3
Self-citationLow-temperature sintering of nanoscale silver paste for double-sided attaching 9×9 mm2 chip
Lian, J., Mei, Y., Chen, X., Li, X., Chen, G., & Zhou, K. (2012) · International Conference on Electronic Packaging Technology (ICEPT) · doi:10.1109/icept-hdp.2012.6474608 · Cited by 3
Self-citationAdvanced Method of Pure Solder Layer Thermal Resistance Measurement in Power Cycling
Liu, J., Zhao, Y., Deng, E., Pan, M., & Huang, Y. (2023) · IEEE International Electrical and Energy Conference (CIEEC) · doi:10.1109/cieec58067.2023.10166397 · Cited by 2
Process and reliability of die attachment by time-reduced sintering of nanosilver film
Dai, J. (2019) · Nottingham ePrints (University of Nottingham) · Cited by 2
Xiang, Y., Zhou, Z. C., Mo, L., Liu, H., & Wu, F. (2017) · International Conference on Electronic Packaging Technology (ICEPT) · doi:10.1109/icept.2017.8046615 · Cited by 2
Redefinition of safety operating area (SOA) considering transient thermal dynamics of IGET module
Liu, Y., Huang, M., Liu, Y., & Zha, X. (2017) · IEEE ... Workshop on Control and Modeling for Power Electronics · doi:10.1109/compel.2017.8013403 · Cited by 1
Collector-Emitter Voltage Based Health Monitoring of Bond Wire in IGBT at Low Gate Voltage
Kumar, P., Arya, A., Chanekar, A. A., Deshmukh, P., & Anand, S. (2022) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce50734.2022.9947879 · Cited by 1
Gao, S., Teng, C., Wang, H., Li, H., & Kang, R. (2024) · Journal of Electronic Materials · doi:10.1007/s11664-024-11341-0 · Cited by 1
Application of STATCOM to improve the LVRT capability of DFIG during VSC fire-through
Abdou, A. F., Abu‐Siada, A., & Pota, H. R. (2013) · eSpace (Curtin University) · Cited by 1
Optoelectronic Materials, Devices, and Applications
Niu, P., Pei, L., Mei, Y., Bai, H., & Shi, J. (2023) · MDPI eBooks · doi:10.3390/books978-3-0365-8649-6 · Cited by 1
Self-citationResearch on Testing Method of Low Voltage IGBT Module Parameter
Niu, P., Gao, W., & Xu, J. (2020) · Communications in computer and information science · doi:10.1007/978-981-33-6378-6_11 · Cited by 1
Liu, S., Vuorinen, V., Schuh, J., Albrecht, J., & Paulasto‐Kröckel, M. (2025) · IEEE Transactions on Components Packaging and Manufacturing Technology · doi:10.1109/tcpmt.2025.3626444
Niu, H., Wang, S., Ye, X., & Zhai, G. (2019) · International Conference on Quality, Reliability, Risk, Maintenance, and Safety Engineering · doi:10.1109/qr2mse46217.2019.9021240
Abdou, A. (2013) · UNSWorks (UNSW Sydney) · doi:10.26190/unsworks/16439
An accurate health-monitoring method for IGBT power module in the traction system
Qie, T., Chen, H., Zeng, Y., Wang, X. J., Xiang, C., Iu, H. H., & Tse, C. K. (2026) · IEEE International Conference on Industrial Cyber-Physical Systems (ICPS) · doi:10.1109/icps70486.2026.11567948
A NUMERICAL STUDY ON EFFICIENCY IMPROVEMENT OF HEAT TRANSFER FOR A 3-PHASE INVERTER
Delaram, H., Dastfan, A., & Mahmood, N. (2015)
Thermo-Mechanical Reliability of 1200V-450A IGBT Module Considering Voids in the Solder Layer
Guo, X. H., Yang, G. D., Fu, J., & Huang, K. (2019) · Materials science forum · doi:10.4028/www.scientific.net/msf.954.202
Hashemabad, S. G. (2015) · Digital Repository Service (Northeastern University) · doi:10.17760/d20200302
Effects of Porosity on Thermal Resistance Aging at Submicron Silver Interfaces
Wang, J., Zhang, M., Yang, C., He, Z., Fu, Z., & Yang, J. (2023) · International Conference on Electronic Packaging Technology (ICEPT) · doi:10.1109/icept59018.2023.10492418
Metadata
- Authors
- Chen, G., Han, D., Mei, Y.-H., Cao, X., Wang, T., Chen, X., & Lu, G.-Q.
- Affiliations
- Tianjin University (CN)
- Virginia Tech (US)
- Venue
- IEEE Transactions on Device and Materials Reliability
- Published
- 2012-03
- Volume
- 12
- Issue
- 1
- Pages
- 124-132
- ISSN
- 1530-4388 (ISSN-L)
- 1558-2574
- OpenAlex
- W2091469028
- Cited by
- 71
- References
- 20
- Citations by year
- 2026: 1 · 2025: 4 · 2024: 3 · 2023: 4 · 2022: 6 · 2021: 1 · 2020: 2 · 2019: 6 · 2018: 5 · 2017: 4 · 2016: 7 · 2015: 7 · 2014: 11 · 2013: 8 · 2012: 2
- FWCI
- 4.70
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- IEEE Transactions on Device and Materials Reliability (publishedVersion)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Electronic Packaging and Soldering Technologies
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Silicon Carbide Semiconductor Technologies
- Physical Sciences › Materials Science › Materials Chemistry › Thermal properties of materials
- Keywords
- IGBT modules, transient thermal impedance, low-temperature soldering, lead-free solder, SAC305, interfacial thermal resistance, power electronics thermal management
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.