A General Energy Balance for Battery Systems
Open accessThe DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index; 2 of the 20 sources its claims cite were checked for support.
Abstract
A general energy balance for battery systems has been developed. This equation is useful for estimating cell thermal characteristics. Reliable predictions of cell temperature and heat‐generation rate are required for the design and thermal management of battery systems. The temperature of a cell changes as a result of electrochemical reactions, phase changes, mixing effects, and joule heating. The equation developed incorporates these effects in a complete and general manner. Simplifications and special cases are discussed. The results of applying the energy balance to a mathematical model of the cell discharged through two different reaction mechanisms are given as examples. The examples illustrate how the energy equation may be applied to a specific system to examine the relative contributions corresponding to the terms in the equation. The examples show that the processes involved in cell heat generation may be complex and that the application of a sufficiently general energy equation is advantageous.
Overview
CoChat Summary
TL;DR
The paper derives a general energy balance for battery systems that includes mixing, phase changes, and simultaneous electrochemical reactions with composition-dependent open-circuit potentials. It applies the equation to a modeled LiAl/LiCl-KCl/FeS cell discharged by two mechanisms and to a lead-acid estimate, showing that cell heat generation can be complex and that a sufficiently general energy equation is advantageous.
Key findings
- A general energy balance is developed that includes energy contributions from mixing, phase changes, and simultaneous electrochemical reactions with composition-dependent open-circuit potentials; prior treatments were restricted to single pure-phase reactants or a single reaction without mixing effects.
- For the LiAl/FeS model, adiabatic-reversible discharge gives the same temperature at 100% depth of discharge for both mechanisms because the overall reaction is the same; slope discontinuities occur at 50% and 12% utilization for mechanisms 1 and 2, respectively. In the realistic simulations, the second reaction begins at 30% and 11% utilization for mechanisms 1 and 2, respectively.
- The mixing term is negligible in the LiAl/FeS example; at 25% utilization, the temperature decline after current interruption is only about 0.2 K. For a lead-acid cell, the estimated temperature rise after full discharge is approximately 1.6 K, or 2.9 K if 1.25 mol of PbO2 is allowed for discharge.
- The sign of the mixing effect depends on the enthalpy curve: for lead-acid, the sulfuric acid-water enthalpy curve is concave upward, so a well-insulated cell heats after current interruption; for the high-temperature LiCl-KCl cell, the curve is concave downward, so the cell cools after interruption. Neglecting mixing overestimates lead-acid operating temperature and underestimates high-temperature cell operating temperature.
Methods
- The paper derives the energy balance from the first law of thermodynamics, assuming uniform battery temperature, and presents a final general equation including reaction, heat-capacity, phase-change, mixing, electrical-work, and heat-transfer terms.
- The equation is applied to an existing one-dimensional mathematical model of the LiAl/LiCl-KCl/FeS cell with a porous LiAl negative electrode, porous FeS positive electrode, electrolyte reservoir, and separator under galvanostatic discharge, using the two reaction mechanisms in Table I.
- Appendix A estimates the lead-acid temperature rise using an assumed uniform 5 molal sulfuric acid electrolyte, with one-third of the electrolyte in the cathode and anode spaces and one-third between the electrodes; the analysis compares adiabatic-reversible profiles with model simulations and examines the relative contributions of terms.
Limitations
- The paper states that the rigorous energy balance is difficult to apply without a detailed mathematical model because instantaneous composition profiles and current fractions are required; in practice, obtaining concentration profiles and predicting current partitioning among possible reactions is difficult.
- The paper states that the analysis does not include enthalpy changes from nonfaradaic reactions; self-discharge or corrosion must be divided into anodic and cathodic components and included as an additional term. The mixing term is also difficult because it involves integrations of concentration profiles.
- The paper states that actual FeS discharge is complicated and more like a mixture of the two proposed mechanisms plus simultaneously occurring chemical reactions; the examples are model simulations. The lead-acid estimate assumes artificial concentration jumps at interfaces, and diffusion would lower the estimate; nonuniform reaction distribution in porous electrodes would make the concentration distribution nonuniform. The breakdown is presented only up to 30% utilization because oscillatory behavior begins when the second reaction starts, to be treated in a subsequent publication.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
0 Valid · 5 Not valid · 12 Not checked · 75 Own results and interpretations
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“Basing the discharge on two Farādays (1 mol PbOg) and a transference number of 0.74 for hydrogen ion, we may calculate that the concentration in the cathode space and anode space drops to 1.04 and 2.79 molal, respectively (14).”
What the sources say
- Could not verifycites [14] 14. Hans Bode, "Lead-Acid Batteries," R. J. Brodd and K. V. Kordesch, Translators, Wiley-Interscience, New York (1977). sourceExperimental — accuracy not yet measured
The available text in the book-review passage (section labeled “Notice to Members April 1 is Cut-Off Date”; page not provided) describes the book’s theoretical treatment of lead-acid batteries but does not give this calculation. Searches for the 0.74 hydrogen-ion transference number, two Faradays, and the 1.04 and 2.79 molal concentrations found no passage addressing the claimed values. (LLM, conf=0.76)
hedgedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 5 assumptions not shown here.
- Could not verify
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“The temperature rise, after full discharge, is approximately 1.6 K.”
- Also stated in: § Estimate of the Temperature Rise in a Lead-Acid Cell Following Current Interruption · p. 8 · hedged
“Using the data available in Ref. (14) (for 298 K), we calculate the temperature rise to be about 1.6 K”
What the sources say
- Could not verifycites [14] 14. Hans Bode, "Lead-Acid Batteries," R. J. Brodd and K. V. Kordesch, Translators, Wiley-Interscience, New York (1977). sourceExperimental — accuracy not yet measured
The available passages from the book review (page not provided) describe the book’s coverage of lead-acid battery thermodynamics but give no temperature rise after full discharge. Searches for “1.6 K” and the discharge-temperature claim found no supporting passage in our copy. (LLM, conf=0.75)
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 5 assumptions not shown here.
- Also stated in: § Estimate of the Temperature Rise in a Lead-Acid Cell Following Current Interruption · p. 8 · hedged
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Although the mixing term offers a negligible contribution to the energy balance, it is interesting to investigate the processes that determine its behavior.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The profile for the X-phase mechanism in Fig. 1 follows the adiabatic-reversible profile up to about 5% utilization because the heat-loss contribution tends to cancel the polarization heat.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“A general energy balance for battery systems has been developed.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 3 assumptions not shown here.
39 more claims
Create a free account to see all 92 claims and every source verdict.
- It may state two separate claims as one. 20
- Probably not a substantial claim. 33
- The quote only partly states this claim. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Conclusions · p. 8
“Equation [23], written for a single cell reaction, is the energy equation most commonly used in battery applications.”
§ Discussion of Terms · p. 5
“Furthermore, Eq. [24] is the form of the energy balance that is most commonly encountered in the literature.”
Citations
Cites
The publisher hasn’t deposited this paper’s reference list.
Research works printed but not linked: 12
- [1]1. J. M. Sherfey and A. Brenner, This Journal, 105, 665 (1958).
- [3]3. H. F. Gibbard, This Journal, 125, 353 (1978).
- [2]2. S. Gross, Energy Convers., 9, 55 (1969).
- [4]4. I. A. Dibrov and V. A. Bykov, Sov. Electrochem., 13, 298 (1977).
- [6]6. L. D. Hansen and R. M. Hart, This Journal, 125, 842 (1978).
- [5]5. I. A. Dibrov and V. A. Bykov, J. Appl. Chem., 49, 2025 (1977).
- [7]7. F. B. Tudron, ibid., 128, 516 (1981).
- [9]9. W. H. Tiedemann and J. Newman, in "Battery Design and Optimization," S. Gross, Editor, pp. 23-38, The Electrochemical Society Softbound Proceedings Series, Princeton, NJ (1979).
- [8]8. D. M. Chen and H. F. Gibbard, ibid., 130, 1975 (1983).
- [10]10. Richard Pollard and John Newman, This Journal, 128, 491 (1981).
- [11]11. Richard Pollard and John Newman, ibid., 128, 502 (1981).
- [13]13. Z. Tomczuk, S. K. Preto, and M. F. Roche, This Journal, 128, 760 (1981).
Cited by
Items 2,301–2,400 of 2,542
Machine Learning Framework for Predicting the Thermal Behaviour of Lithium-Ion BatteriesPreprint
Wang, X., Li, L., Jin, Y., & Tassou, S. A. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.6213824
ezz, I., Abdelrehim, O., Saafan, M. M., et al. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.6221808
Yang, Z., Liu, F., Bai, W., et al. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.6221727
Liu, Z., Qiao, B., & Qi, N. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2026.121039
Bai, H., Wang, L., Cao, Y., et al. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.6240099
Siricharoenpanich, A., Faraji, H., Poojeera, S., et al. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.6248896
Peng, J., Fu, F., Jia, Y., Wu, C., Cao, G., & Zhang, H. (2026) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2026.3665750 · Cited by 1
“As per Bernardi’s classical model, the heat generation rate in an operating battery is governed by the combined e ff ect of ohmic losses and the entropic heat of electrochemical reactions [31].”
Tuğan, V. (2026) · Journal of Thermal Science and Engineering Applications · doi:10.1115/1.4071171
Mousavi, E., Abdollahi, F., Barazandeh, F., et al. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.6278603
Shamnaz, M., Bal, D. K., & Sahoo, B. B. (2026) · Results in Engineering · doi:10.1016/j.rineng.2026.109756 · Cited by 2
Mohammed, S. R., Halkarni, S. S., Chakravarty, A., et al. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.6301139
Yaşar, O. (2026) · Karadeniz Fen Bilimleri Dergisi · doi:10.31466/kfbd.1676184
Chang, A., Wang, S., & Zhou, K. (2026) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2026-01-7042 · Cited by 1
Liu, F., Zou, P., Liu, S., et al. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.6309726
Charapale, O., Saini, D., Singh, A. K., Yadav, P. K., Garg, A., Gao, L., Wei, K., Shu, X., & Liu, X. (2026) · Journal of Electrochemical Energy Conversion and Storage · doi:10.1115/1.4071280
Pan, C., Xu, W., Wang, L., et al. (2026) · Proceedings of the Institution of Mechanical Engineers Part D Journal of Automobile Engineering · doi:10.1177/09544070261420525
Kalathingal, A., Kuzhiyil, J. A., Grandjean, T. R. B., et al. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.6353310
Somek, K., Papurello, D., Bressan, M., et al. (2026) · Energy Storage · doi:10.1002/est2.70365
“The heat generation during constant-current charge and discharge was evaluated using the Bernardi heat generation model [29].”
Peng, C., Shi, J., Dang, X., et al. (2025) · International Conference on Computational Modeling, Simulation and Data Analysis (CMSDA) · doi:10.1109/cmsda68297.2025.11414387
“Assuming the internal heat source of the battery is stable and uniform, the heat generation rate can be expressed ( ) In the formula, q represents the heat generation rate is the temperature coefficient, taken as 0.25 mV/K in this case [14] .”
InfluentialWind, J., Ostrander, J. W., Gilljam, M., Lian, T., Wragg, D. S., Foss, C. E. L., Hassani, A., Iveland, A., & Vie, P. J. S. (2026) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/ae508f · Cited by 2
Liu, F., Zou, P., Liu, S., et al. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.6408969
Thermal management of lithium-ion batteries with Flexible Composite Phase Change FilmsPreprint
Zhou, T. F., He, C., Feng, H. Y., et al. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.6412565
蒋, 若. (2026) · Interdisciplinary Science Letters · doi:10.12677/isl.2026.102062
Impact of nonlinear thermal effects on electrochemical performance in lithium-ion cells
El‐Nabulsi, R. A., & Anukool, W. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2026.121633
Phan, T. T., Song, D., Nguyen, X. L., et al. (2026) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2026.111026
Jahromi, H. B., Mehmandoosti, M. M., & Kowsary, F. (2026) · Thermal Science and Engineering Progress · doi:10.1016/j.tsep.2026.104672
Zeng, K., Tian, L., Ye, Z., et al. (2026) · Journal of Physics Conference Series · doi:10.1088/1742-6596/3208/1/012008
“Based on the above assumptions, the governing equations are established in the following form: The heat generation rate in operating batteries is governed by the Bernardi equation: [10] The discharge current and battery temperature are denoted as I and 𝑇 𝑏 , respectively.”
Zhang, Y., Cao, L., Zhang, Q., Jiang, G., & Li, J. (2026) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2026.130882
Li, Y., Wang, C., Wang, H., Feng, Y., Wang, L., & Liao, C. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2026.121715
Optimisation multicritère de la gestion de la recharge d'une flotte de bus électriques
Houbbadi, A. (2020) · theses.fr (ABES) · doi:10.70675/c11d5029z9eb7z492aza271z2f4ee3f984c3
Caractérisation 3D et modélisation multi-échelle des matériaux actifs de batteries
Kerdja, Y. (2020) · theses.fr (ABES) · doi:10.70675/5b7cfcc8z7a38z402dzbcc5z9d41b06990c3 · Cited by 1
Energy management strategies for battery electric bus fleet
Basma, H. (2020) · theses.fr (ABES) · doi:10.70675/115e3dbez194bz4518z900bzb4cb466d97f4 · Cited by 1
Jiang, C., Wang, J., Yang, L., et al. (2026) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2026.128800
Numerical Simulation and Uncertainty Quantification for Immersion Cooling of Lithium-ion Batteries
Solaï, E. (2022) · theses.fr (ABES) · doi:10.70675/60c4c184zb3f8z4d15z9de8z3b117a07e822 · Cited by 4
Operando optical sensing for battery diagnosis
Blanquer, L. A. (2022) · theses.fr (ABES) · doi:10.70675/f2560be9z70adz4da6zafeaz9126f43a8596
Vazquez-Rodriguez, A. (2023) · theses.fr (ABES) · doi:10.70675/666fc9dezf8bdz4981z981bz0857294ac56c
Thermal Management of Li-ion Battery Using Passive Cooling Technique
Yadav, V., Yadav, K., Agrawal, M., et al. (2026) · doi:10.1615/ihmtc-2025.250
Abbas, A. (2025) · theses.fr (ABES) · doi:10.70675/488a5d24z7236z4578za9bfzbf8c5169e519 · Cited by 1
Optimization of Battery Preheating Strategy for Connected Electric Vehicles During Driving
He, J., Zeng, X., Cauwer, C. D., Hosen, M. S., Allocco, A., & Berecibar, M. (2026) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2026.3683572
Virag, Z., Krizmanić, S., Živić, M., et al. (2026) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2026.131041
Tian, J., & Xu, S. M. A. Z. (2026) · Journal of Energy Engineering · doi:10.1061/jleed9.eyeng-6426
Lagnoni, M., Quilici, F. G., Cademartori, D., Scarpelli, C., Mithoowani, U. N., Barontini, F., Ruvio, A., Puccini, M., Lutzemberger, G., Carpanese, M. P., et al. (2026) · Advanced Science · doi:10.1002/advs.75306 · Cited by 2
“The electrochemical model was coupled with a 0D thermal model to account for cell temperature variations during operation, following the well-established framework introduced by Bernardi et al. [ 82–86 ], accounting for reversible and irreversible heat contributions.”
BATTERY DIGITAL TWIN FRAMEWORK IN SIMULINK FOR VOLTAGE AND TEMPERATURE MONITORING
Velumani, D., & Bansal, A. (2026) · Proceeding of Second Thermal and Fluids Engineering Conference · doi:10.1615/tfec2026.mes.061422
Priyaswi, K., Sudha, K. R., & Garg, A. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.6618674
Li, Y., Li, Y., Lu, W., et al. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.6628871
Ye, Z., Ye, D., Wu, Y., et al. (2026) · Applied Sciences · doi:10.3390/app16094277
Advanced Fuzzy Control for Thermal Management of Sodium-Ion Batteries
Zhang, X., Liu, Z., & Su, H. (2025) · China Automation Congress (CAC) · doi:10.1109/cac67268.2025.11487547
“According to the Bernardi energy balance [8]: Where C p is the specific heat capacity of the battery, M is the mass of the battery, dU ocv dt is the entropy coefficient of the battery, h is the heat transfer coefficient, S is the heat transfer area, and T amb is the ambient temperature.”
Li, M., Zongyi, H., Jiahan, H., et al. (2026) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2026.131240
Miszneder, M., Rengstl, U., Hopp‐Hirschler, M., et al. (2026) · World Electric Vehicle Journal · doi:10.3390/wevj17050238
Rud, M., Tarandushka, L., Rud, M., et al. (2026) · Lecture notes in electrical engineering · doi:10.1007/978-3-032-18415-3_19
Peng, H., Liu, H., She, X., et al. (2026) · Case Studies in Thermal Engineering · doi:10.1016/j.csite.2026.108139
ezz, I., Abdelrehim, O., Saafan, M. M., El-Gendy, E. M., & El-Awady, W. A. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2026.122584
Hu, Q., Zheng, A., Liu, Y., et al. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2026.122613
Shaikh, U. I., Kamble, D., Kore, S., et al. (2026) · Heat Transfer · doi:10.1002/htj.70271
Zeng, Z., Jü, X., Yao, X., et al. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2026.122582
Yang, S., Sun, J., Wang, Y., Chen, Y., Li, M., Du, J., & Wu, X. (2026) · Batteries · doi:10.3390/batteries12050170
Lee, S., Lee, S., Son, Y., et al. (2026) · Transactions of Korean Society of Automotive Engineers · doi:10.7467/ksae.2026.34.5.523
Lu, X., 谢以湛, Li, Y., et al. (2026) · eTransportation · doi:10.1016/j.etran.2026.100608
Chetri, C., Huynh, A., Anekal, L., & Williamson, S. S. (2025) · IEEE International Conference on Power Electronics, Smart Grid, and Renewable Energy (PESGRE) · doi:10.1109/pesgre65581.2025.11521250
“The rate of heat generation inside the battery is shown in Equation 1 [3] , where U and V denote the terminal and open-circuit voltages, I denotes the current, T denotes the cell temperature, and ∂U/∂T represents the entropic coefficient.”
Degradation‐Informed Temperature Analysis for Cycle Life Prediction of LiFePO 4 Batteries
Kee, J., Lee, S., Hwang, J., Yoon, S., Han, S., & Kim, D. (2026) · Battery energy · doi:10.1002/bte2.70124 · Cited by 1
THERMAL MANAGEMENT OF PRISMATIC LITHIUM-ION BATTERIES USING SERPENTINE LIQUID COOLING CHANNEL
Dehingia, S., & Perumal, D. A. (2026) · Interfacial phenomena and heat transfer · doi:10.1615/interfacphenomheattransfer.2026063223
Lee, S.-E., Lee, J. B., Yoon, J., An, H., Suh, H., Kim, Y., & Kim, J. (2026) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2026.3696642
“Here, H tr represents the heat transfer coe ffi cient, and A denotes the surface area of the battery cell [7], [24].”
Dynamic suppression of temperature buildup in coin batteries via PCM utilization
Aryanfar, A., Bozkurt, B., & Goddard, W. A., III (2026) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2026.131589
Synergistic liquid cooling design and optimization for 18650 battery modules in electric bicycles
Sun, J., Cai, L., Chen, Y., et al. (2026) · Thermal Science · doi:10.2298/tsci2603343s
Amer, M., Assi, M., & Elsisi, M. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2026.122789
Siricharoenpanich, A., Faraji, H., Poojeera, S., Srichat, A., Vengsungnle, P., Eiamsa‐ard, S., & Naphon, P. (2026) · Thermal Science and Engineering Progress · doi:10.1016/j.tsep.2026.104772
Wang, Q., Chang, Z., Hu, Y., et al. (2026) · Advanced Energy Materials · doi:10.1002/aenm.71153
“Based on the foundational Bernardi energy balance equation [58], the fractional contribution of each irreversible heat source is determined by the ratio of its respective resistance to the total polarization resistance ( R i / R total ) [59, 60].”
Thermal Modeling of a Cylindrical Lithium-Ion Battery in 3D with the Taguchi Optimization Method
Kaya, E., & D'Adamo, A. (2026) · Batteries · doi:10.3390/batteries12060201
Research on Heat Generation Inconsistency and Indirect Liquid Cooling Strategies for Aged BatteriesPreprint
Zhao, C., Li, Y., Chen, M.-M., et al. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.6863560
Bianco, N. D., Masi, R. F. D., Fragnito, A., et al. (2026) · Thermo · doi:10.3390/thermo6020040
“Q b represent the temperature of the battery and the heat source term, which follows Bernardi’s electro-thermal model [10].”
Thakur, S. S., Dhuper, K., & Kumar, L. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2026.122871
Dzorgbenyo, I. S., & Kowal, J. (2026) · Journal of Power Sources · doi:10.1016/j.jpowsour.2026.240469
Wang, X., Yuan, F., Guo, F., et al. (2026) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2026.106995
Nam, D., Lee, S., Lee, Y., et al. (2026) · Journal of Mechanical Science and Technology · doi:10.1007/s12206-026-0529-x
“Based on the classical formulation proposed by Bernardi et al. [19] and the general lumped-thermal-energy framework [20], the internal heat-generation term includes both irreversible and reversible electrochemical contributions, providing a physically consistent basis for decoupling battery heat…”
Thermal management of lithium-ion batteries with flexible composite phase change films
Zhou, T., He, C., Feng, H., et al. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2026.122975
Dai, Y., Ting, Y.-C., & Chang, C. (2026) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2026.111678
Peng, D., Zhong, S., Dun, Y., & Kang, Z. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2026.122999
Liu, F., Zou, P., Liu, S., et al. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.6901759
Thermal Management of Lithium-Ion Battery Packs in Electric Vehicles
Anilkumar, P. (2026) · International Journal of Technical Research Studies (IJTRS) · doi:10.63090/ijtrs/3139.1788.0016
Ma, S., Liu, Q., Liu, W., et al. (2026) · Processes · doi:10.3390/pr14121882
Huo, Y., & You, S. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.6915442
Electrochemical-mechanical-thermal modeling for lithium-ion batteries
Mei, W., Cheng, Z., She, C., Liu, C., Sun, J., & Wang, Q. (2026) · The Innovation · doi:10.1016/j.xinn.2026.101472
Yao, K., Ao, Y., Han, F., Yu, Y., Zhao, K., & Zhu, L. (2026) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2026.132907
Elfeky, K. E., Hosny, M., Mohammed, A. G., et al. (2026) · Ain Shams Engineering Journal · doi:10.1016/j.asej.2026.104300
Chen, C., Ye, C., Zheng, Y., et al. (2026) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2026.131931
Deep Koopman Observer for Lithium-Ion Battery Temperature Estimation
Abdullah, M. H., & Kandil, S. M. (2026) · World Electric Vehicle Journal · doi:10.3390/wevj17060310
Onreabroy, W., & Kaewpradap, A. (2026) · World Electric Vehicle Journal · doi:10.3390/wevj17060311 · Cited by 1
“Heat generation [60,61] was estimated using Equation (1): where m b is the mass of the battery cell [kg], C P is the specific heat of a battery [J/kg · K], T i is the initial temperature [ 2) and (3), respectively. where Q J is the heat of electric losses or Joule heating [W], I is the current of…”
Enhancing air-cooled Li-ion battery pack performance via transverse cell spacing
Venu, I., Sourav, K., & Nagireddy, P. D. (2026) · Thermal Science and Engineering Progress · doi:10.1016/j.tsep.2026.104803
Zhang, X., Zhou, Y.-H., Huang, Z.-X., et al. (2026) · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · doi:10.1177/09544062261458900
“14 Building on this, some researchers have incorporated mechanical fields into battery modeling frameworks, developing coupled mechanical-electrical-thermal models to investigate the effects of compressive deformation on electrochemical behavior.”
Niu, W., Pu, J., & Xu, Q. (2026) · Heat and Mass Transfer · doi:10.1007/s00231-026-03718-0
“The most classic and widely used model is the uniform heat generation rate model proposed by Bernardi et al. [ 28].”
Peng, F., Peng, A., Chen, Y., et al. (2026) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2026.132043
Chen, W., Lan, H., Guo, G., et al. (2026) · Journal of Energy Engineering · doi:10.1061/jleed9.eyeng-6780
A Novel Method for Determining the Specific Heat Capacity of Cylindrical Li-Ion Batteries
Sotirov, S. S., & Kafadarova, N. M. (2026) · Batteries · doi:10.3390/batteries12070226
“…modeling of lithium-ion cells requires reliable specific heat capacity data, since it is a key parameter in all thermal models—from the early energy-balance model of Bernardi et al. [26] to modern electrochemical-thermal [27–29], electrothermal [14,30], and runaway propagation models [31,32].”
Mission-oriented early-stage design of Mars rotorcraft considering battery thermal managementPreprint
Park, S., Park, J., Hong, Y., et al. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.6999273
Kalathingal, A., Kuzhiyil, J. A., Grandjean, T. R. B., Dinh, T., & Niri, M. F. (2026) · Energy and AI · doi:10.1016/j.egyai.2026.100808 · Cited by 2
Yamagata, M., Wakita, Y., Fujita, A., Miyata, K., Matsumoto, T., & Aoyanagi, Y. (2026) · Aerospace Science and Technology · doi:10.1016/j.ast.2026.113048 · Cited by 1
Nematollahi, M., Omrani, M., Ghassemi, M., & Shafii, M. B. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.7004932
Metadata
- Authors
- Bernardi, D., Pawlikowski, E., & Newman, J.
- Affiliations
- University of California, Berkeley (US)
- ORCID
- Newman, J.
- Venue
- Journal of The Electrochemical Society
- Publisher
- The Electrochemical Society
- Published
- 1985-01-01
- Volume
- 132
- Issue
- 1
- Pages
- 5-12
- ISSN
- 0013-4651 (ISSN-L)
- 1945-7111
- OpenAlex
- W2023385933
- Cited by
- 2,548
- References
- 0
- Citations by year
- 2026: 383 · 2025: 387 · 2024: 339 · 2023: 265 · 2022: 238 · 2021: 167 · 2020: 147 · 2019: 106 · 2018: 74 · 2017: 89 · 2016: 42 · 2015: 53 · 2014: 75 · 2013: 51 · 2012: 31
- FWCI
- 0.00
- Type
- journal article
- Language
- en
- Open access
- bronze
- doi.org
- Licence
- iopscience.iop.org/page/copyright (vor, 12758 d)
- iopscience.iop.org/info/page/text-and-data-mining (tdm, 12758 d)
- Locations
- Journal of The Electrochemical Society (publishedVersion)
- Topics
- Physical Sciences › Engineering › Automotive Engineering › Battery Modeling and Management
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advancements in Battery Materials
- Physical Sciences › Chemistry › Electrochemistry › Molten salt chemistry and electrochemical processes
- Keywords
- heat generation rate, Joule heating, phase transitions, mixing effects, electrochemical reactions, battery thermal management, battery modeling
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.