A General Energy Balance for Battery Systems
Open accessThe DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index; 2 of the 20 sources its claims cite were checked for support.
Abstract
A general energy balance for battery systems has been developed. This equation is useful for estimating cell thermal characteristics. Reliable predictions of cell temperature and heat‐generation rate are required for the design and thermal management of battery systems. The temperature of a cell changes as a result of electrochemical reactions, phase changes, mixing effects, and joule heating. The equation developed incorporates these effects in a complete and general manner. Simplifications and special cases are discussed. The results of applying the energy balance to a mathematical model of the cell discharged through two different reaction mechanisms are given as examples. The examples illustrate how the energy equation may be applied to a specific system to examine the relative contributions corresponding to the terms in the equation. The examples show that the processes involved in cell heat generation may be complex and that the application of a sufficiently general energy equation is advantageous.
Overview
CoChat Summary
TL;DR
The paper derives a general energy balance for battery systems that includes mixing, phase changes, and simultaneous electrochemical reactions with composition-dependent open-circuit potentials. It applies the equation to a modeled LiAl/LiCl-KCl/FeS cell discharged by two mechanisms and to a lead-acid estimate, showing that cell heat generation can be complex and that a sufficiently general energy equation is advantageous.
Key findings
- A general energy balance is developed that includes energy contributions from mixing, phase changes, and simultaneous electrochemical reactions with composition-dependent open-circuit potentials; prior treatments were restricted to single pure-phase reactants or a single reaction without mixing effects.
- For the LiAl/FeS model, adiabatic-reversible discharge gives the same temperature at 100% depth of discharge for both mechanisms because the overall reaction is the same; slope discontinuities occur at 50% and 12% utilization for mechanisms 1 and 2, respectively. In the realistic simulations, the second reaction begins at 30% and 11% utilization for mechanisms 1 and 2, respectively.
- The mixing term is negligible in the LiAl/FeS example; at 25% utilization, the temperature decline after current interruption is only about 0.2 K. For a lead-acid cell, the estimated temperature rise after full discharge is approximately 1.6 K, or 2.9 K if 1.25 mol of PbO2 is allowed for discharge.
- The sign of the mixing effect depends on the enthalpy curve: for lead-acid, the sulfuric acid-water enthalpy curve is concave upward, so a well-insulated cell heats after current interruption; for the high-temperature LiCl-KCl cell, the curve is concave downward, so the cell cools after interruption. Neglecting mixing overestimates lead-acid operating temperature and underestimates high-temperature cell operating temperature.
Methods
- The paper derives the energy balance from the first law of thermodynamics, assuming uniform battery temperature, and presents a final general equation including reaction, heat-capacity, phase-change, mixing, electrical-work, and heat-transfer terms.
- The equation is applied to an existing one-dimensional mathematical model of the LiAl/LiCl-KCl/FeS cell with a porous LiAl negative electrode, porous FeS positive electrode, electrolyte reservoir, and separator under galvanostatic discharge, using the two reaction mechanisms in Table I.
- Appendix A estimates the lead-acid temperature rise using an assumed uniform 5 molal sulfuric acid electrolyte, with one-third of the electrolyte in the cathode and anode spaces and one-third between the electrodes; the analysis compares adiabatic-reversible profiles with model simulations and examines the relative contributions of terms.
Limitations
- The paper states that the rigorous energy balance is difficult to apply without a detailed mathematical model because instantaneous composition profiles and current fractions are required; in practice, obtaining concentration profiles and predicting current partitioning among possible reactions is difficult.
- The paper states that the analysis does not include enthalpy changes from nonfaradaic reactions; self-discharge or corrosion must be divided into anodic and cathodic components and included as an additional term. The mixing term is also difficult because it involves integrations of concentration profiles.
- The paper states that actual FeS discharge is complicated and more like a mixture of the two proposed mechanisms plus simultaneously occurring chemical reactions; the examples are model simulations. The lead-acid estimate assumes artificial concentration jumps at interfaces, and diffusion would lower the estimate; nonuniform reaction distribution in porous electrodes would make the concentration distribution nonuniform. The breakdown is presented only up to 30% utilization because oscillatory behavior begins when the second reaction starts, to be treated in a subsequent publication.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
0 Valid · 5 Not valid · 12 Not checked · 75 Own results and interpretations
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“Basing the discharge on two Farādays (1 mol PbOg) and a transference number of 0.74 for hydrogen ion, we may calculate that the concentration in the cathode space and anode space drops to 1.04 and 2.79 molal, respectively (14).”
What the sources say
- Could not verifycites [14] 14. Hans Bode, "Lead-Acid Batteries," R. J. Brodd and K. V. Kordesch, Translators, Wiley-Interscience, New York (1977). sourceExperimental — accuracy not yet measured
The available text in the book-review passage (section labeled “Notice to Members April 1 is Cut-Off Date”; page not provided) describes the book’s theoretical treatment of lead-acid batteries but does not give this calculation. Searches for the 0.74 hydrogen-ion transference number, two Faradays, and the 1.04 and 2.79 molal concentrations found no passage addressing the claimed values. (LLM, conf=0.76)
hedgedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 5 assumptions not shown here.
- Could not verify
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“The temperature rise, after full discharge, is approximately 1.6 K.”
- Also stated in: § Estimate of the Temperature Rise in a Lead-Acid Cell Following Current Interruption · p. 8 · hedged
“Using the data available in Ref. (14) (for 298 K), we calculate the temperature rise to be about 1.6 K”
What the sources say
- Could not verifycites [14] 14. Hans Bode, "Lead-Acid Batteries," R. J. Brodd and K. V. Kordesch, Translators, Wiley-Interscience, New York (1977). sourceExperimental — accuracy not yet measured
The available passages from the book review (page not provided) describe the book’s coverage of lead-acid battery thermodynamics but give no temperature rise after full discharge. Searches for “1.6 K” and the discharge-temperature claim found no supporting passage in our copy. (LLM, conf=0.75)
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 5 assumptions not shown here.
- Also stated in: § Estimate of the Temperature Rise in a Lead-Acid Cell Following Current Interruption · p. 8 · hedged
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Although the mixing term offers a negligible contribution to the energy balance, it is interesting to investigate the processes that determine its behavior.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The profile for the X-phase mechanism in Fig. 1 follows the adiabatic-reversible profile up to about 5% utilization because the heat-loss contribution tends to cancel the polarization heat.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“A general energy balance for battery systems has been developed.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 3 assumptions not shown here.
39 more claims
Create a free account to see all 92 claims and every source verdict.
- It may state two separate claims as one. 20
- Probably not a substantial claim. 33
- The quote only partly states this claim. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Conclusions · p. 8
“Equation [23], written for a single cell reaction, is the energy equation most commonly used in battery applications.”
§ Discussion of Terms · p. 5
“Furthermore, Eq. [24] is the form of the energy balance that is most commonly encountered in the literature.”
Citations
Cites
The publisher hasn’t deposited this paper’s reference list.
Research works printed but not linked: 12
- [1]1. J. M. Sherfey and A. Brenner, This Journal, 105, 665 (1958).
- [3]3. H. F. Gibbard, This Journal, 125, 353 (1978).
- [2]2. S. Gross, Energy Convers., 9, 55 (1969).
- [4]4. I. A. Dibrov and V. A. Bykov, Sov. Electrochem., 13, 298 (1977).
- [6]6. L. D. Hansen and R. M. Hart, This Journal, 125, 842 (1978).
- [5]5. I. A. Dibrov and V. A. Bykov, J. Appl. Chem., 49, 2025 (1977).
- [7]7. F. B. Tudron, ibid., 128, 516 (1981).
- [9]9. W. H. Tiedemann and J. Newman, in "Battery Design and Optimization," S. Gross, Editor, pp. 23-38, The Electrochemical Society Softbound Proceedings Series, Princeton, NJ (1979).
- [8]8. D. M. Chen and H. F. Gibbard, ibid., 130, 1975 (1983).
- [10]10. Richard Pollard and John Newman, This Journal, 128, 491 (1981).
- [11]11. Richard Pollard and John Newman, ibid., 128, 502 (1981).
- [13]13. Z. Tomczuk, S. K. Preto, and M. F. Roche, This Journal, 128, 760 (1981).
Cited by
Items 1,901–2,000 of 2,542
Heat dissipation characteristics for lithium battery pack of AUV
Bian, X., & Wang, Z. (2016) · International Conference on Advanced Robotics and Mechatronics (ICARM) · doi:10.1109/icarm.2016.7606980 · Cited by 1
“…outer wall of battery cabin is heat conduction of cylindrical wall [6], which can be expressed as follows: ci c ci coA k t t (9) ci co ci c t t A k (10) where: ciA is heat transfer area of inner wall, ck is equivalent heat conductivity of battery wall, and tci is temperature of battery inner wall.”
BackgroundSimulation and Experimental Verification of Temperature Field for Square Lithium-ion Power Battery
Jin, B., Fei, Q., Wang, Y., et al. (2022) · Journal of Physics Conference Series · doi:10.1088/1742-6596/2166/1/012049 · Cited by 1
“2 At present, the widely used heat generation theory of battery was proposed by bernardi et al [4].”
MethodWang, X.-Z., & Ke-qun, L. (2022) · Acta Physica Sinica · doi:10.7498/aps.71.20220212 · Cited by 1
Open-source tool for battery module simulation and design
Estevez, M. A. P., & Renzi, M. (2022) · Journal of Physics Conference Series · doi:10.1088/1742-6596/2330/1/012010 · Cited by 1
Comparative Study on Different Particle Size Distributions of Porous Electrodes
杨, 佳. (2023) · Modeling and Simulation · doi:10.12677/mos.2023.123264 · Cited by 1
Battery thermal modeling: Models and prospects
Liu, Z., You, H., Abudula, A., et al. (2023) · Elsevier eBooks · doi:10.1016/b978-0-443-19017-9.00024-6 · Cited by 1
Research on Structural Design and Optimization of Battery Thermal Management System
Xi, L., Zhang, H., Gao, M., et al. (2023) · International Journal of Energy · doi:10.54097/ije.v3i1.9806 · Cited by 1
Napa, N., Agrawal, M. K., & Tamma, B. (2023) · IEEE International Conference on Sustainable Energy and Future Electric Transportation (SEFET) · doi:10.1109/sefet57834.2023.10244838 · Cited by 1
Influence of the Generation of Gas Bubbles in Flooded Lead–Acid Batteries on Their Thermal Behavior
Nahidi, S., Salari, M., Gavzan, I. J., et al. (2024) · Journal of Engineering Physics and Thermophysics · doi:10.1007/s10891-024-02868-4 · Cited by 1
“To date, various theories have been proposed for the factors increasing the temperature of the batteries [2, 6, 14, 39–41].”
Predicting PCM-based passive battery thermal performance in varying ambient temperature
Talele, V., Sangaj, V., Ahire, S., & Patil, M. S. (2024) · Elsevier eBooks · doi:10.1016/b978-0-443-19025-4.00003-8 · Cited by 1
Chen, Y., Hongqiang, Z., & Liu, Q. (2024) · Journal of Physics Conference Series · doi:10.1088/1742-6596/2741/1/012047 · Cited by 1
Research on Optimization of Low Temperature Cold Start Strategy of PEMFC for Automotive Application
邓, 精. (2024) · Modeling and Simulation · doi:10.12677/mos.2024.133248 · Cited by 1
Chen, H., Zhang, T., Gao, Q., et al. (2024) · Sustainable Energy Technologies and Assessments · doi:10.1016/j.seta.2024.104013 · Cited by 1
Active Thermal Management Control Design for Battery and Compute Components of the Zoox Robotaxi*
Zheng, Q., Yen, Y.-H., & Mueller, P. (2024) · International Conference on Advanced Robotics and Mechatronics (ICARM) · doi:10.1109/icarm62033.2024.10715763 · Cited by 1
“D models [8-12].”
Kavasoğullari, B. (2024) · Black Sea Journal of Engineering and Science · doi:10.34248/bsengineering.1545174 · Cited by 1
Hou, T., & Lin, L. (2024) · Experimental Heat Transfer · doi:10.1080/08916152.2024.2420942 · Cited by 1
“…on the assumption of uniform heat generation inside lithium-ion batteries, the battery uniform heat generation model proposed by Bernardi D et al. [40] was adopted: where Q t is the heat generation rate or total heating power of the battery, W; I is the charging or discharging current ( I < 0…”
Passive Thermal Management of an Electric Trainer Aircraft Battery Pack Considering Aging
Veilleux, É., Pasdarshahri, H., Rancourt, D., et al. (2024) · Journal of Aircraft · doi:10.2514/1.c038205 · Cited by 1
Core Temperature Estimation for Lithium-Ion Batteries Based on Extended Kalman Filter
Jin, Y., Liu, X., Zhang, Z., Peng, Z., & Yang, S. (2025) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2025-01-7020 · Cited by 1
Babu, A. R., Sebben, S., Chronéer, Z., & Etemad, S. (2025) · Thermal Science and Engineering Progress · doi:10.1016/j.tsep.2025.103417 · Cited by 2
Maitra, T., Mishra, S., Patra, A., & Bhattacharya, A. (2025) · Thermal Science and Engineering Progress · doi:10.1016/j.tsep.2025.103503 · Cited by 1
Zhang, T., Xu, Y., Li, L., et al. (2025) · Frontiers in Heat and Mass Transfer · doi:10.32604/fhmt.2025.064287 · Cited by 1
“The heat generation model developed by Bernadi et al. [31] is commonly used to calculate the rate of heat production in batteries.”
Guo, X., Xu, R., Zhang, J., et al. (2025) · World Electric Vehicle Journal · doi:10.3390/wevj16050249 · Cited by 1
Oyekola, E., Swan, L. G., & Dahn, J. R. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.116803 · Cited by 1
Thermal performance of marine power batteries and optimization of their liquid cooling systems
Li, X., Guo, X., Lu, X., et al. (2026) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2026.128981 · Cited by 1
Böhm, K., Bracht, C., Kallfaß, C., et al. (2025) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/adda7a · Cited by 1
Zheng, J., Jiang, J., Yu, X., et al. (2025) · JUSTC · doi:10.52396/justc-2023-0133 · Cited by 1
Feasibility of Martian Solar Powered Unmanned Aerial Vehicles in 2030s
Huang, Y. J., & Yinji, H. (2025) · doi:10.17352/iast.000005 · Cited by 1
Revealing the Heat Generation and Release in a High-Energy-Density Quasi-Solid-State Li-Ion Cell
Yang, M., Qi, X., Zhang, W., et al. (2025) · Energy & Fuels · doi:10.1021/acs.energyfuels.5c02028 · Cited by 1
Li, J., Ma, Y., Gao, J., et al. (2025) · Energy · doi:10.1016/j.energy.2025.137593 · Cited by 1
Chen, Z., Jia, L., & Ren, H. (2025) · Case Studies in Thermal Engineering · doi:10.1016/j.csite.2025.106863 · Cited by 1
Study on thermal characteristics of LiCoxNiyMn1-x-yO2-LiFePO4 mixed battery pack
Chen, Z., Hu, J., Shen, J., Liu, Y., Zhang, Y., Liu, Y., Wei, F., & Zhang, D. (2025) · Case Studies in Thermal Engineering · doi:10.1016/j.csite.2025.106919 · Cited by 2
Chen, Q., Xu, Z., Xu, C., Hu, Q., Huang, X., & Tang, T. (2025) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/adfd8f · Cited by 1
Progress in Design and Development of Battery Thermal Management System for Electric Vehicles
Swamy, K. A., & Verma, S. (2025) · Energy, environment, and sustainability · doi:10.1007/978-981-96-6624-9_7 · Cited by 1
Zhang, J., Yu, L., Zhang, H., et al. (2025) · doi:10.1109/ieeeconf65522.2025.11137334 · Cited by 1
“According to reference [18], the heat of the battery can be defined as: Where 𝐼 is the load current; 𝑇 𝑏 is the temperature of the battery; 𝑈 𝑜𝑝 is the open-circuit voltage of the battery; 𝑅 is the internal resistance of the battery pack; 𝑑𝑈 𝑜𝑝 /𝑑𝑇 𝑏 is the entropy coefficient of the…”
Yang, Z., Li, M., Rao, M., et al. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2026.122679 · Cited by 1
Li, H., Fang, Y., Yuan, B., Lu, X., Li, M., Gu, Z., & Zhu, X. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.128553 · Cited by 1
Zhang, R., Qiu, Z., Li, Y., et al. (2025) · Chemical Engineering Journal · doi:10.1016/j.cej.2025.169654 · Cited by 1
Xu, Q., Huang, Y. K., Li, L., Wang, X., Zheng, K., & Lin, X. (2025) · Journal of Renewable and Sustainable Energy · doi:10.1063/5.0282541 · Cited by 1
Zheng, Y., Che, Y., Hu, X., et al. (2025) · doi:10.1109/intelec63987.2025.11214734 · Cited by 1
“A simplified model derived from Bernardi et al. [13] can be used to describe the internal heat generation, which is expressed as where I , V , and V oc are the current (positive for charging and negative for discharging), voltage, and open circuit voltage (OCV), respectively, ∂V oc /∂T is the…”
Gao, Y., Han, F., Zeng, X., et al. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.119449 · Cited by 1
Comprehensive feasibility study on partition use in lithium-ion battery immersion cooling system
Kong, W., Gao, L., & Ji, Z. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.119550 · Cited by 1
Ren, Z., Di, L., Cao, J., et al. (2025) · Measurement · doi:10.1016/j.measurement.2025.119000 · Cited by 1
Liu, S., Xiong, W., Fan, W., et al. (2025) · Advanced Sustainable Systems · doi:10.1002/adsu.202501186 · Cited by 1
Zhang, M. H., Li, K., Wei, Y., et al. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2025.120261 · Cited by 1
A fast Rint–PCM model of phase-change heat distribution to optimize energy storage in an LFP cell
Chen, G. W., Li, W., Wu, T., et al. (2026) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2025.110162 · Cited by 1
Hao, Z., Li, Z., Li, X., et al. (2026) · Journal of Power Sources · doi:10.1016/j.jpowsour.2025.239226 · Cited by 1
Jia, B., Cai, Z., Zhang, P., et al. (2026) · Batteries · doi:10.3390/batteries12010024 · Cited by 1
“Lithium-ion batteries (LIBs) have become pivotal in this transition owing to their high energy density, long cycle life, and environmental friendliness [1–3].”
Guerra, J., Benavides, I., Barzola, J., Montenegro, V., & Castejón, C. (2026) · IEEE Access · doi:10.1109/access.2026.3660171 · Cited by 1
“At cell level, the Bernardi formulation provides the canonical heat-generation model linking electrochemical and irreversible Joule terms, which underpins the 0D/1D balances used here [11], [12].”
Guo, S., Ma, C., Xu, J., Liu, J., Yin, W., Lili, L. I. U., & Ye, J. (2026) · Advanced Sustainable Systems · doi:10.1002/adsu.202501711 · Cited by 1
“At present, battery SOC estimation methods are generally categorized into open-loop approaches (e.g., Coulomb counting and open-circuit voltage) [12], filter/observer-based approaches relying on equivalent-circuit or electrochemical models [13, 14], and data-driven learning-based methods [15–17].”
Khoshvaght-Aliabadi, M., Ghodrati, P., Feizabadi, A., & Kang, Y. T. (2026) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2026.129927 · Cited by 2
Dai, C., Wang, C., Li, D., et al. (2026) · Science China Technological Sciences · doi:10.1007/s11431-025-3188-1 · Cited by 1
“In this study, Bernardi’s battery heat generation theory [34] is adopted, which incorporates reversible heat effects and derives the heat generation equation through energy balance principles.”
Ye, F., Zhang, Y., Han, J., Nie, L., & Xue, X. (2026) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2026.130349 · Cited by 1
Xin, Q., Zhang, X., Yang, T., Zhang, H., & Xiao, J. (2026) · Batteries · doi:10.3390/batteries12030078 · Cited by 2
“The heat generation of the battery is commonly described using the model proposed by Bernardi et al. [20], which decomposes the total heat generation into Joule heat and reversible reaction heat to characterize the thermal behavior during the discharge process of lithium-ion batteries.”
InfluentialKo, J., Kim, J.-H., & Kang, C. (2026) · Heat and Mass Transfer · doi:10.1007/s00231-026-03649-w · Cited by 1
Bose, A., & Chanda, A. (2026) · Journal of Mechanical Science and Technology · doi:10.1007/s12206-026-0262-5 · Cited by 1
Liu, Z., Yin, L., & Zhu, T. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2026.121594 · Cited by 1
Jeong, Y. S., Chandran, K. N., Ha, M. Y., & Min, J. K. (2026) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2026.130760 · Cited by 3
Stereoscopic Serpentine Channel‐Based Cold Plate Design for Enhanced Liquid Cooling of EV Batteries
Kanjirakat, A., Saldanha, R., K., P. G., et al. (2026) · Battery energy · doi:10.1002/bte2.70109 · Cited by 1
Yu, R., Wang, M., Niu, M., Fan, M., Guan, Y., & Su, Y. (2026) · Journal of Energy Chemistry · doi:10.1016/j.jechem.2026.03.047 · Cited by 6
Investigation of Lithium-Ion Battery Degradation in Electric Aircraft Under Cycle-Progressive Loads
Boggan, C., & Clarke, M. A. (2026) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2026.3681423 · Cited by 1
“Next,we will utilize a form of the Bernardi equation [13] for heat generation Q g of a lithium-ion battery where ˙ Q rev and ˙ Q irr represent the reversible and irreversible heat generated, respectively.”
Chau, N. M., Quynh, L. V., Quang, N. M., Ngoc, N. T. H., Cong, N. T., & Hieu, N. T. (2026) · Batteries · doi:10.3390/batteries12040138 · Cited by 2
Zhou, F., ZHENG, K., Yang, Z., Zou, Z., Meng, J., Song, Z., & Geng, Y. (2026) · Energy · doi:10.1016/j.energy.2026.141105 · Cited by 1
Ge, F., Chen, Y., & Zuo, Z. (2026) · IEEE Transactions on Cybernetics · doi:10.1109/tcyb.2026.3683396 · Cited by 2
“D heat generation rate Q ( x , y , t ) proposed in [26] can be presented as follows [16], [20], [22]: where σ ( x , y ) represents the nonuniform distribution, v is the cell volume, I ( t ) is the battery current, R s ( T ( x , y , t ) , S oC ( t )) denotes battery internal resistance that depends…”
Owida, H. A., Mohammad, S. I., Vasudevan, A., Shomurotova, S., Rekha, M. M., Agarwal, A., Singh, A., Sharma, R., Khalef, A., & Nikpendar, A. (2026) · Sustainable Energy & Fuels · doi:10.1039/d5se01494h · Cited by 1
Zhao, H., Wu, K., Shao, Y., et al. (2026) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2026.128919 · Cited by 1
Liu, Y., Wang, N., An, L., et al. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2026.122357 · Cited by 1
A hybrid battery thermal management system with integrated flame retardant material
Xu, Q., Chui, H., Xu, Y., et al. (2026) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2026.131435 · Cited by 1
Bou-Rabee, M., Alelaj, F. M., Fadel, M., et al. (2026) · Systems Science & Control Engineering · doi:10.1080/21642583.2026.2728376 · Cited by 1
Kang, Z., Jin, G., Yin, R., et al. (2026) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2026.129032 · Cited by 1
Zhang, X., Yang, K., Zhang, S., et al. (2026) · Case Studies in Thermal Engineering · doi:10.1016/j.csite.2026.108216 · Cited by 1
Mohammed, A. G., Hasini, H., Elfeky, K. E., Ali, M. H., & Wang, Q. (2026) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2026.117144 · Cited by 2
Yang, C., Gu, B., Li, X., Zhang, X., & Zhang, X. (2026) · Batteries · doi:10.3390/batteries12060198 · Cited by 2
Li, Y., Wang, R., Jin, Y., Sun, Z., Liu, H., Liu, Y., Liu, Y., Xu, J. Q., Tao, Y., Jiang, Z., et al. (2026) · Batteries · doi:10.3390/batteries12060202
Yang, G., Xiao, G., Pan, C., Wu, J., & Jia, Z. (2026) · Energies · doi:10.3390/en19112687 · Cited by 2
Shi, H., Zhang, J., Zhang, G., Mo, C., Su, X., Wang, X., Wen, Y., Jiang, L., & Jiang, W. (2026) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2026.131843 · Cited by 1
Cao, H., 孙亚松, Xiong, W., et al. (2026) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2026.131861 · Cited by 1
Kaewchoothong, N., Oo, Y. M., Gonsrang, S., & Sengchuai, K. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2026.123204 · Cited by 1
Wu, X., Ji, C., Yunxiu, H., et al. (2026) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2026.132179 · Cited by 1
Analysis of the delay effect of phase change materials for battery thermal runaway protection
Hou, Z., Han, Y., Wang, J., Yang, Q., Yuan, X., Li, K., Lei, H., Yang, F., Wang, J., Shen, H., et al. (2026) · Applied Physics A · doi:10.1007/s00339-026-09888-2 · Cited by 2
“In the Ber-nardi model, reaction heat Q r correlates with current I, temperature T, and the enthalpy coefficient of entropy dU ocv /dT [23 ].”
Ren, Q., Chen, Y., Xue, K., et al. (2026) · Journal of Physics D Applied Physics · doi:10.1088/1361-6463/ae8705 · Cited by 1
“The heat generation equation for a single lithium-ion battery is expressed as follows [45]: where ϕ s is the heat generation rate per unit volume, V s is the effective volume of a single cell, I is the current passing through the battery, R is the internal resistance of the battery T b is the…”
Mei, Y., Li, G., & Yang, K. (2026) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2026.111151 · Cited by 1
The role of cooling plate–battery contact angle in liquid-cooled cylindrical battery packs
Birinci, S., Albayrak, M., Sarper, B., Yazıcı, M. Y., Saglam, M., & Aydın, O. (2026) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2026.111177 · Cited by 1
Characterization of Li-ion batteries for battery energy storage systems (BESS)
Oguike, C., & Lorente, S. (2026) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2026.132435 · Cited by 1
Bae, J., Sun, Y. W., & Han, J. (2026) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2026.132431 · Cited by 1
Fan, X., Wang, Z., Zhou, H., Lin, Q., Hu, J., Wang, J., Huo, Y., & Tu, J. Y. (2026) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2026.112089 · Cited by 2
Research on heat generation inconsistency and indirect liquid cooling strategies for aged batteries
Zhao, C., Li, Y., Chen, M., et al. (2026) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2026.132554 · Cited by 1
Zhang, Y., Wang, H., Cui, X., et al. (2026) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2026.111214 · Cited by 1
Yang, H., Jiao, Z., Gu, M., Zhang, S., & Qiao, Y. (2026) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2026.112092 · Cited by 1
Zhang, C., Tian, W., Hong, L., et al. (2026) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2026.132607 · Cited by 1
Thermal Analysis of Lithium Ion Batteries Using in HEV
Fofana, G. H., & Zhang, Y. T. (2013) · Applied Mechanics and Materials · doi:10.4028/www.scientific.net/amm.470.362 · Cited by 1
“Bernardi proposed a general energy balance equation [5] for battery thermal models in which the homogeneous heat generation rate is given by ( ) oc oc dV I g T V V dT υ = − − (8)”
BackgroundThermal Characterization of Lithium Polymer Battery Module for Electric Vehicle Application
Maruvada, T., Patidar, L., & Patel, M. (2014) · Applied Mechanics and Materials · doi:10.4028/www.scientific.net/amm.575.620 · Cited by 1
“Fig (9) Shows the time variation of temperature of the middle cell and comparison of experimental and simulation results.”
BackgroundInfluential[Perforation of the rectosigmoideal junction by ingestión of foreign bodies].
Jiménez-Rodríguez, R. M., Flores-Cortés, M., Méndez, C., et al. (2009) · PubMed · doi:10.4321/s1130-01082009001200015 · Cited by 1
Modeling of current distribution in a lithium-ion battery
Liu, W., Wang, L., Liao, C., et al. (2014) · doi:10.1109/itec-ap.2014.6940677 · Cited by 1
Hybrid electric vehicle simulation with integrated battery Compact Physical Model
Arnett, M., Papadimitriou, I., & Milios, J. (2014) · IEEE Transportation Electrification Conference and Expo · doi:10.1109/itec.2014.6861867 · Cited by 1
“Heat generated in the cell can be attributed to electrochemical reactions, phase changes, mixing effects and Joule heating [11].”
BackgroundElectric Vehicle Lithium Ion Batteries Thermal Management
Fofana, G. H., & Zhang, Y. T. (2013) · TELKOMNIKA Indonesian Journal of Electrical Engineering · doi:10.11591/telkomnika.v12i3.4026 · Cited by 1
“Bernardi proposed a general energy balance equation [3] for battery thermal models in which the homogeneous heat generation rate is given by: oc oc dV I g V V T dT (13)”
BackgroundInfluentialResearch on the Heat Dissipation Characteristics of Lithium Battery Spatial Layout in an AUV
Mao, Z., & Yan, S. (2016) · Discrete Dynamics in Nature and Society · doi:10.1155/2016/6269539 · Cited by 1
“In [13], a model of a large-scale battery pack was established for investigating battery pack heat dissipation; it primarily concentrated on the field of electric power for new energy vehicles.”
Analytical thermal model for characterizing a Li-ion battery cell
Cicconi, P., Germani, M., & Landi, D. (2013) · doi:10.1109/evs.2013.6914896 · Cited by 1
Effiziente Vorhersage des thermischen Verhaltens einer Traktionsbatterie unter dynamischer Last
Hüske, M., Lenz, M., Jaworczak, K., et al. (2019) · Proceedings · doi:10.1007/978-3-658-25294-6_10 · Cited by 1
Modeling the Impedance Characterization of Prismatic Lithium-Ion Batteries
Ghalkhani, M., & Mehrtash, M. (2019) · Procedia Manufacturing · doi:10.1016/j.promfg.2019.02.283 · Cited by 1
Hassanzade, M., & Rahmani, Z. (2020) · Journal of Control · doi:10.29252/joc.13.4.1 · Cited by 1
Metadata
- Authors
- Bernardi, D., Pawlikowski, E., & Newman, J.
- Affiliations
- University of California, Berkeley (US)
- ORCID
- Newman, J.
- Venue
- Journal of The Electrochemical Society
- Publisher
- The Electrochemical Society
- Published
- 1985-01-01
- Volume
- 132
- Issue
- 1
- Pages
- 5-12
- ISSN
- 0013-4651 (ISSN-L)
- 1945-7111
- OpenAlex
- W2023385933
- Cited by
- 2,548
- References
- 0
- Citations by year
- 2026: 383 · 2025: 387 · 2024: 339 · 2023: 265 · 2022: 238 · 2021: 167 · 2020: 147 · 2019: 106 · 2018: 74 · 2017: 89 · 2016: 42 · 2015: 53 · 2014: 75 · 2013: 51 · 2012: 31
- FWCI
- 0.00
- Type
- journal article
- Language
- en
- Open access
- bronze
- doi.org
- Licence
- iopscience.iop.org/page/copyright (vor, 12758 d)
- iopscience.iop.org/info/page/text-and-data-mining (tdm, 12758 d)
- Locations
- Journal of The Electrochemical Society (publishedVersion)
- Topics
- Physical Sciences › Engineering › Automotive Engineering › Battery Modeling and Management
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advancements in Battery Materials
- Physical Sciences › Chemistry › Electrochemistry › Molten salt chemistry and electrochemical processes
- Keywords
- heat generation rate, Joule heating, phase transitions, mixing effects, electrochemical reactions, battery thermal management, battery modeling
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.