A General Energy Balance for Battery Systems
Open accessThe DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index; 2 of the 20 sources its claims cite were checked for support.
Abstract
A general energy balance for battery systems has been developed. This equation is useful for estimating cell thermal characteristics. Reliable predictions of cell temperature and heat‐generation rate are required for the design and thermal management of battery systems. The temperature of a cell changes as a result of electrochemical reactions, phase changes, mixing effects, and joule heating. The equation developed incorporates these effects in a complete and general manner. Simplifications and special cases are discussed. The results of applying the energy balance to a mathematical model of the cell discharged through two different reaction mechanisms are given as examples. The examples illustrate how the energy equation may be applied to a specific system to examine the relative contributions corresponding to the terms in the equation. The examples show that the processes involved in cell heat generation may be complex and that the application of a sufficiently general energy equation is advantageous.
Overview
CoChat Summary
TL;DR
The paper derives a general energy balance for battery systems that includes mixing, phase changes, and simultaneous electrochemical reactions with composition-dependent open-circuit potentials. It applies the equation to a modeled LiAl/LiCl-KCl/FeS cell discharged by two mechanisms and to a lead-acid estimate, showing that cell heat generation can be complex and that a sufficiently general energy equation is advantageous.
Key findings
- A general energy balance is developed that includes energy contributions from mixing, phase changes, and simultaneous electrochemical reactions with composition-dependent open-circuit potentials; prior treatments were restricted to single pure-phase reactants or a single reaction without mixing effects.
- For the LiAl/FeS model, adiabatic-reversible discharge gives the same temperature at 100% depth of discharge for both mechanisms because the overall reaction is the same; slope discontinuities occur at 50% and 12% utilization for mechanisms 1 and 2, respectively. In the realistic simulations, the second reaction begins at 30% and 11% utilization for mechanisms 1 and 2, respectively.
- The mixing term is negligible in the LiAl/FeS example; at 25% utilization, the temperature decline after current interruption is only about 0.2 K. For a lead-acid cell, the estimated temperature rise after full discharge is approximately 1.6 K, or 2.9 K if 1.25 mol of PbO2 is allowed for discharge.
- The sign of the mixing effect depends on the enthalpy curve: for lead-acid, the sulfuric acid-water enthalpy curve is concave upward, so a well-insulated cell heats after current interruption; for the high-temperature LiCl-KCl cell, the curve is concave downward, so the cell cools after interruption. Neglecting mixing overestimates lead-acid operating temperature and underestimates high-temperature cell operating temperature.
Methods
- The paper derives the energy balance from the first law of thermodynamics, assuming uniform battery temperature, and presents a final general equation including reaction, heat-capacity, phase-change, mixing, electrical-work, and heat-transfer terms.
- The equation is applied to an existing one-dimensional mathematical model of the LiAl/LiCl-KCl/FeS cell with a porous LiAl negative electrode, porous FeS positive electrode, electrolyte reservoir, and separator under galvanostatic discharge, using the two reaction mechanisms in Table I.
- Appendix A estimates the lead-acid temperature rise using an assumed uniform 5 molal sulfuric acid electrolyte, with one-third of the electrolyte in the cathode and anode spaces and one-third between the electrodes; the analysis compares adiabatic-reversible profiles with model simulations and examines the relative contributions of terms.
Limitations
- The paper states that the rigorous energy balance is difficult to apply without a detailed mathematical model because instantaneous composition profiles and current fractions are required; in practice, obtaining concentration profiles and predicting current partitioning among possible reactions is difficult.
- The paper states that the analysis does not include enthalpy changes from nonfaradaic reactions; self-discharge or corrosion must be divided into anodic and cathodic components and included as an additional term. The mixing term is also difficult because it involves integrations of concentration profiles.
- The paper states that actual FeS discharge is complicated and more like a mixture of the two proposed mechanisms plus simultaneously occurring chemical reactions; the examples are model simulations. The lead-acid estimate assumes artificial concentration jumps at interfaces, and diffusion would lower the estimate; nonuniform reaction distribution in porous electrodes would make the concentration distribution nonuniform. The breakdown is presented only up to 30% utilization because oscillatory behavior begins when the second reaction starts, to be treated in a subsequent publication.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
0 Valid · 5 Not valid · 12 Not checked · 75 Own results and interpretations
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“Basing the discharge on two Farādays (1 mol PbOg) and a transference number of 0.74 for hydrogen ion, we may calculate that the concentration in the cathode space and anode space drops to 1.04 and 2.79 molal, respectively (14).”
What the sources say
- Could not verifycites [14] 14. Hans Bode, "Lead-Acid Batteries," R. J. Brodd and K. V. Kordesch, Translators, Wiley-Interscience, New York (1977). sourceExperimental — accuracy not yet measured
The available text in the book-review passage (section labeled “Notice to Members April 1 is Cut-Off Date”; page not provided) describes the book’s theoretical treatment of lead-acid batteries but does not give this calculation. Searches for the 0.74 hydrogen-ion transference number, two Faradays, and the 1.04 and 2.79 molal concentrations found no passage addressing the claimed values. (LLM, conf=0.76)
hedgedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 5 assumptions not shown here.
- Could not verify
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“The temperature rise, after full discharge, is approximately 1.6 K.”
- Also stated in: § Estimate of the Temperature Rise in a Lead-Acid Cell Following Current Interruption · p. 8 · hedged
“Using the data available in Ref. (14) (for 298 K), we calculate the temperature rise to be about 1.6 K”
What the sources say
- Could not verifycites [14] 14. Hans Bode, "Lead-Acid Batteries," R. J. Brodd and K. V. Kordesch, Translators, Wiley-Interscience, New York (1977). sourceExperimental — accuracy not yet measured
The available passages from the book review (page not provided) describe the book’s coverage of lead-acid battery thermodynamics but give no temperature rise after full discharge. Searches for “1.6 K” and the discharge-temperature claim found no supporting passage in our copy. (LLM, conf=0.75)
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 5 assumptions not shown here.
- Also stated in: § Estimate of the Temperature Rise in a Lead-Acid Cell Following Current Interruption · p. 8 · hedged
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Although the mixing term offers a negligible contribution to the energy balance, it is interesting to investigate the processes that determine its behavior.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The profile for the X-phase mechanism in Fig. 1 follows the adiabatic-reversible profile up to about 5% utilization because the heat-loss contribution tends to cancel the polarization heat.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“A general energy balance for battery systems has been developed.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 3 assumptions not shown here.
39 more claims
Create a free account to see all 92 claims and every source verdict.
- It may state two separate claims as one. 20
- Probably not a substantial claim. 33
- The quote only partly states this claim. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Conclusions · p. 8
“Equation [23], written for a single cell reaction, is the energy equation most commonly used in battery applications.”
§ Discussion of Terms · p. 5
“Furthermore, Eq. [24] is the form of the energy balance that is most commonly encountered in the literature.”
Citations
Cites
The publisher hasn’t deposited this paper’s reference list.
Research works printed but not linked: 12
- [1]1. J. M. Sherfey and A. Brenner, This Journal, 105, 665 (1958).
- [3]3. H. F. Gibbard, This Journal, 125, 353 (1978).
- [2]2. S. Gross, Energy Convers., 9, 55 (1969).
- [4]4. I. A. Dibrov and V. A. Bykov, Sov. Electrochem., 13, 298 (1977).
- [6]6. L. D. Hansen and R. M. Hart, This Journal, 125, 842 (1978).
- [5]5. I. A. Dibrov and V. A. Bykov, J. Appl. Chem., 49, 2025 (1977).
- [7]7. F. B. Tudron, ibid., 128, 516 (1981).
- [9]9. W. H. Tiedemann and J. Newman, in "Battery Design and Optimization," S. Gross, Editor, pp. 23-38, The Electrochemical Society Softbound Proceedings Series, Princeton, NJ (1979).
- [8]8. D. M. Chen and H. F. Gibbard, ibid., 130, 1975 (1983).
- [10]10. Richard Pollard and John Newman, This Journal, 128, 491 (1981).
- [11]11. Richard Pollard and John Newman, ibid., 128, 502 (1981).
- [13]13. Z. Tomczuk, S. K. Preto, and M. F. Roche, This Journal, 128, 760 (1981).
Cited by
Items 1,701–1,800 of 2,542
Temperature Distribution on Lithium-Ion Polymer Battery Cell: Experiment and Modeling
Liu, Y., Liao, Y. G., & Lai, M. (2019) · IEEE Vehicular Technology Conference · doi:10.1109/vtcfall.2019.8890974 · Cited by 4
Battery Loss Modelling Using Equivalent Circuits
Liu, S., Forsyth, A. J., & Todd, R. (2019) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2019.8912542 · Cited by 4
“Whilst detailed electro-chemical energy models and analyses exist for battery efficiency [5], [6], these are usually physics-based and are often not readily accessible to application engineers.”
BackgroundLi, Y., & Tao, Y. (2019) · Chinese Science Bulletin (Chinese Version) · doi:10.1360/tb-2019-0285 · Cited by 4
Batteries: Basic Principles, Technologies, and Modeling
Botte, G. G. (2007) · Wiley eBooks · doi:10.1002/9783527610426.bard050007 · Cited by 5
Mousaei, A., & Allahyari, H. (2023) · Research Square · doi:10.21203/rs.3.rs-2650526/v1 · Cited by 4
Numerical Investigations on Immersion Cooling of Lithium-Ion Batteries using Different Coolants
Ajay, G., Krishna, R., Mythirayan, B., et al. (2025) · Thermal Engineering · doi:10.1134/s0040601524600111 · Cited by 3
“A simplified version for calculating heat generation in battery cells, developed by Bernardi et al., [20] is used in this study given by (4) where is the battery volume, m 3 ; I is current, A; is the internal resistance of the battery in ohms; T is the battery temperature, K; v i R is the entropic…”
Design optimization of the structure of fishbone channels in a battery liquid cooling plate
Wu, C., Li, C., Wei, X., Yang, J., & Chen, L. (2025) · Energy Storage and Saving · doi:10.1016/j.enss.2025.05.001 · Cited by 5
Dağdevir, T., Lin, X., & Ding, Y. (2025) · Journal of Mechanical Science and Technology · doi:10.1007/s12206-025-0857-2 · Cited by 3
“In addition, many researchers have employed a heat generation equation by Bernardi et al. [32] for simulating the heat generation inside the LIB cell as if the battery were just a heat resistance by ignoring the electrochemical reactions.”
Simulation Study on the Single-Phase Immersion Cooling Performance of Lithium-Ion Battery Packs
Hu, J., Yu, B., Chen, Z., et al. (2025) · Applied Sciences · doi:10.3390/app15179531 · Cited by 3
A new TEG-supported thermal management system of the battery system for an electric vehicle
Mavi, A., & Arslan, O. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.128608 · Cited by 3
Lu, X., Guo, S., Fan, X., et al. (2025) · Energy · doi:10.1016/j.energy.2025.138894 · Cited by 3
Yuan, Y., Louhichi, B., & Heidarshenas, B. (2025) · Thermal Science and Engineering Progress · doi:10.1016/j.tsep.2025.104240 · Cited by 3
Rawat, S. S., Yadav, Y., & Kumar, R. (2025) · Engineering Research Express · doi:10.1088/2631-8695/ae19d0 · Cited by 3
Amuta, O., Droese, D., & Kowal, J. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.119871 · Cited by 7
Numerical study of battery thermal management system with added Iwp structure cooling channel design
Liang, L., Bao, R., Li, H., et al. (2025) · Case Studies in Thermal Engineering · doi:10.1016/j.csite.2025.106725 · Cited by 3
Wang, Z., Song, Y., Zhao, Q., Yu, X., & Shi, B. (2025) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2025.110447 · Cited by 5
Performance analysis of hybrid battery thermal management system based on field synergy principle
Zi, J., Long, W., & Zhao, R. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.119531 · Cited by 3
A comparison of the thermal and electrical properties of two different battery cells
Demiröz, G., Tahirağaoğlu, B., & Sevilgen, G. (2025) · Case Studies in Thermal Engineering · doi:10.1016/j.csite.2025.107583 · Cited by 4
Lu, Y., Sun, B., Li, L., et al. (2025) · Case Studies in Thermal Engineering · doi:10.1016/j.csite.2025.107607 · Cited by 3
Sukkuea, A., Srivisut, K., & Pao-la-or, P. (2025) · Results in Engineering · doi:10.1016/j.rineng.2025.108921 · Cited by 3
Bianco, N., Somma, M. D., Iasiello, M., Menale, C., Piccirillo, F., & Vellucci, F. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2025.119641 · Cited by 5
Ren, F., Lu, D., Yuan, H., & Cui, N. (2026) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2025.3645428 · Cited by 6
“The simplified energy balance equation by Bernardi et al. [25] was often used to calculate the total heat generation of battery, which can be expressed as follows: where Q irr is the irreversible heat, generated by losses in the active material; Q rev is the reversible heat, which is generated by…”
Qian, L., Zhang, W. Z., Fei, G., et al. (2026) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/ae3e1b · Cited by 3
Liu, F., Liu, J., & Su, W. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2026.120960 · Cited by 5
Arumugam, A., Buonomo, B., Nardini, S., & Manca, O. (2026) · Case Studies in Thermal Engineering · doi:10.1016/j.csite.2026.107831 · Cited by 6
Zeng, J., Yang, Z., Zhu, H., Chen, Y., Huang, T., Tan, P., Zhou, X., Zhou, M., Zhang, Y., & Zhou, H. (2026) · Energy storage materials · doi:10.1016/j.ensm.2026.105002 · Cited by 6
Rawat, S. S., Yadav, Y., & Kumar, R. (2026) · Energy Storage · doi:10.1002/est2.70376 · Cited by 3
“In the study, uncertainty analysis is performed using methodology recommended by Kline and McClintock [37, 38] which applies the root sum of squares method for error propagation.”
Pang, Y., Li, K., Liu, J., Xie, Y., Huang, K., & Huang, C. (2026) · Control Engineering Practice · doi:10.1016/j.conengprac.2026.106952 · Cited by 4
Shen, C., Su, C., Zhang, Z., Wang, F., Wang, Z., & Wang, S. (2026) · Applied Sciences · doi:10.3390/app16073200 · Cited by 3
Hua, Y., Wang, C., Luo, C., et al. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2026.122232 · Cited by 3
Ghaedi, M., Moghimi, M., & Bahrami, H. (2026) · Energy Conversion and Management X · doi:10.1016/j.ecmx.2026.101897 · Cited by 3
Physics-Informed Neural Networks for Thermal Anomaly Prediction in Battery Energy Storage Systems
Vairo, T., Guarino, S., Reverberi, A. P., & Fabiano, B. (2026) · Energies · doi:10.3390/en19112503 · Cited by 3
Loss Model and Finite Element Analysis Thermal Model of a Production Fast Charging Battery Module
Thornton, J., Kollmeyer, P., Panchal, S., et al. (2026) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2026-01-0123 · Cited by 3
Awarke, A., Jaeger, M., Pischinger, S., et al. (2012) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2011-01-2443 · Cited by 3
“Measured/calculated electric potentials and currents can be used in order to estimate the cell heat generation rate based on the equation developed by Bernardi [27]: (2) The first term in the equation above is the irreversible heat source, which is always positive and dominant at high rates.”
BackgroundMethodInfluentialModeling and Simulation Analysis of Electric Vehicle Battery Cooling System
Deng, B., Yin, Z., Shangguan, W., et al. (2023) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2023-01-0771 · Cited by 3
Numerical Analysis on Thermal Management Performance of Lithium-Ion Battery Pack with Liquid Cooling
Zeng, J., Fu, H., Feng, S., Lai, C., Song, J., Fu, L., Chen, H., & Gao, T. (2023) · Lecture notes in electrical engineering · doi:10.1007/978-981-99-1027-4_84 · Cited by 3
Lu, X., Chen, N., Li, H., Guo, S., & Chen, Z. (2023) · Energy · doi:10.1016/j.energy.2023.128458 · Cited by 3
Xu, H., Xiong, S., Li, W., Wu, L., & Wang, Z. (2023) · Journal of Electrochemical Energy Conversion and Storage · doi:10.1115/1.4063324 · Cited by 6
Abhijith, T. S., Shijina, S. S., Rabeeh, V. M., et al. (2023) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2023.121877 · Cited by 3
Akkus, F., & IŞIK, M. Z. (2023) · Batman Üniversitesi Yaşam Bilimleri Dergisi · doi:10.55024/buyasambid.1339607 · Cited by 3
Thermoeconomic Analysis of a Compact Active Coolant System for Lithium-Ion Battery Pack
Khan, R., Agarwal, P. K., & Acharya, S. (2024) · Journal of Thermophysics and Heat Transfer · doi:10.2514/1.t6899 · Cited by 3
Nogdhe, Y., Garg, R., & Singh, S. K. (2024) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2024-28-0068 · Cited by 4
Experimental investigation on thermal performance of battery using composite phase change material
Powar, K. P., & Patil, S. D. (2024) · Multiscale and Multidisciplinary Modeling Experiments and Design · doi:10.1007/s41939-024-00631-z · Cited by 3
“The theoretical expression of heat generation in the battery neglecting heat of mixing as well as heat of phase change as proposed by Bernardi et al. (Bernardi et al. 1985) is, where, Q gen is the rate of heat generation (W), I is the current (A), U OCV is the open circuit voltage (V), V is the battery terminal voltag…”
Thenaisie, G., & Couto, L. D. (2024) · Discover Electronics · doi:10.1007/s44291-024-00031-0 · Cited by 3
“Models that have been coupled to the P2D model are, for instance, thermal models derived from energy balance [178–180] and aging mechanisms obtained from electrochemical principles, such as side reactions that give rise to SEI formation and growth [181] as well as lithium plating [182].”
Folorunso, O., Sadiku, E. R., Hamam, Y., & Kupolati, W. K. (2024) · Batteries · doi:10.3390/batteries10120417 · Cited by 4
Trivella, A., Radrizzani, S., Corno, M., & Savaresi, S. M. (2025) · Control Engineering Practice · doi:10.1016/j.conengprac.2024.106228 · Cited by 3
Modified Pseudo-Two-Dimensional Model for Spiral-Wound Cylindrical Lithium-Ion Batteries
Kumar, V., & Sharma, A. K. (2025) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/add093 · Cited by 3
Chen, L., Zeng, X., Xia, X., Sun, Y., & Yue, J. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.116809 · Cited by 4
Koca, F., & Özcan, R. (2025) · Physica Scripta · doi:10.1088/1402-4896/add96a · Cited by 3
Jia, Y., Cao, G., & Gao, J. (2025) · IEEE Access · doi:10.1109/access.2025.3582081 · Cited by 3
Tubeless shape-stabilized phase change materials channels for all-climate battery thermal management
Xu, X., Li, P., Weng, K., Zheng, P., Feng, Y., Liu, D., Hu, S., Qu, W., Shao, J., & Zou, D. (2025) · Energy · doi:10.1016/j.energy.2025.136872 · Cited by 4
Dai, Y., Ting, Y.-C., Chang, C. M., & Huang, C.-T. (2025) · Next Energy · doi:10.1016/j.nxener.2025.100465 · Cited by 4
Yaqteen, M. A., Moon, S., & Kim, J. S. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.128873 · Cited by 3
Tahirağaoğlu, B., Sevilgen, G., & Bürümlü, M. (2025) · Case Studies in Thermal Engineering · doi:10.1016/j.csite.2025.107492 · Cited by 4
Performance assessment of a novel hybrid cooling design for battery thermal management systems
Elfeky, K. E., Hosny, M., Mohammed, A. G., et al. (2025) · Case Studies in Thermal Engineering · doi:10.1016/j.csite.2025.107393 · Cited by 3
Determination of Li-Ion Battery Degradation Mechanisms at High C-Rate Charging
Murashko, K., Li, D., Danilov, D. L., Notten, P. H. L., Pyrhonen, J. J., & Jokiniemi, J. K. (2019) · IEEE Vehicle Power and Propulsion Conference (VPPC) · doi:10.1109/vppc46532.2019.8952302 · Cited by 5
“The heat generation curve obtained after cylindrical cell charging was modified by using a simplified form of the battery heat equation presented in [26].”
MethodArdani, M. I., Wahid, M. A., Talib, M. H. A., et al. (2020) · Materials Today Proceedings · doi:10.1016/j.matpr.2020.04.681 · Cited by 3
Li, G., Xu, G., Yaping, D., Huang, Z., Yang, X., & Ma, L. (2021) · International Journal of Energy Research · doi:10.1002/er.7549 · Cited by 5
Two-dimensional Modeling and Analysis of Lithium-ion Cell for Electric Vehicle Application
Priyadarshi, H., Ahmed, G., Singh, K., & Shrivastava, A. (2021) · International Conference on Recent Developments in Control, Automation & Power Engineering (RDCAPE) · doi:10.1109/rdcape52977.2021.9633549 · Cited by 3
Doh, C., Ha, Y., Eom, S.-W., et al. (2022) · Journal of Electrochemical Science and Technology · doi:10.33961/jecst.2021.00661 · Cited by 3
Bhat, P., & Varpe, M. K. (2022) · Lecture notes in mechanical engineering · doi:10.1007/978-981-19-2091-2_2 · Cited by 3
Electrochemical Change Induced by Spherical Indentation in Lithium-Ion Batteries
Lin, H.-C., Chen, K.-C., & Chen, C. (2022) · Batteries · doi:10.3390/batteries8120268 · Cited by 3
Vyas, S. D., Roy, T., & Dey, S. (2022) · IEEE Conference on Control Technology and Applications (CCTA) · doi:10.1109/ccta49430.2022.9966084 · Cited by 5
“where T1 and T2 are the battery core and surface temperatures, respectively; T∞ is the ambient temperature which is the temperature of cooling system here; R1 and R2 are the thermal resistances of the battery between its core and surface, and surface and ambient, respectively; C1 and C2 are the heat capacities of the…”
BackgroundZhang, M., Wang, S., Wang, J., et al. (2023) · IEEE International Conference on Electrical Engineering, Big Data and Algorithms (EEBDA) · doi:10.1109/eebda56825.2023.10090673 · Cited by 3
Tian, S., Liu, Z., Yang, Q., Xu, N., Li, X., Wang, D., Liu, R., & Lü, W. (2023) · Batteries · doi:10.3390/batteries9070366 · Cited by 3
“At the same time, after pre-heating, the unit area positive reversible heat production rate decreased from 25 W/s in Figure 11a, to 16.25 W/s in Figure 11c during the 800 s charging period; this indicates that the proportion of reversible heat in the total heat release decreased as the cell…”
BackgroundInfluentialHilmy, M. R., Rahman, M. A., Pranoto, I., et al. (2024) · Applied Mechanics and Materials · doi:10.4028/p-eczhk2 · Cited by 3
“(2) and can be converted into: value can be found by the area of half the battery blanket in the axial direction, while the value is obtained through the equation developed by Bernardi et al. [9].”
MethodGayathri, R., Husna, M., Poojasri, R., Sutha, S., Pappa, N., & Vijayakarthick, M. (2024) · IFAC-PapersOnLine · doi:10.1016/j.ifacol.2024.05.030 · Cited by 4
Zhao, Y., Hao, J., Hu, J., Zhou, K., Chen, B., & Wang, Y. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.123897 · Cited by 4
Li, Y., Li, B., Bei, S., Li, L., Zhang, L., & Hu, M. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.124186 · Cited by 3
Multi-Level Thermal Modeling and Management of Battery Energy Storage Systems
Lv, Z., Sun, Z., Wang, L., Liu, Q., & Zhang, J. (2025) · Batteries · doi:10.3390/batteries11060219 · Cited by 5
“Bernardi et al. [15] proposed a comprehensive energy balance framework as a thermal model for battery systems.”
Doosthosseini, M., & Fathy, H. K. (2020) · Proceedings of the ... American Control Conference/Proceedings of the American Control Conference · doi:10.23919/acc45564.2020.9147802 · Cited by 3
Lyu, C., Sheng, Y., Zhang, S., et al. (2020) · IEEE Conference on Industrial Electronics and Applications (ICIEA) · doi:10.1109/iciea48937.2020.9248374 · Cited by 3
“[10] Newman, Bernardi, Pawlikowski, “A General Energy-Balance for Battery Systems,” Journal of the Electrochemical Society, 1985.”
BackgroundEnergetic Sustainability of Systems
Albini, A., Budavári, E. A., & Rajnai, Z. (2020) · International Conference on Interdisciplinarity in Engineering (INTER-ENG) · doi:10.3390/proceedings2020063050 · Cited by 3
Effect of locally enhanced heat dissipation of the polar on Li-ion power batteries
Fang, H., Cao, J. T., Xu, K., Cai, L., Wu, H., & Wu, Q. (2020) · Thermal Science · doi:10.2298/tsci201016351f · Cited by 3
“According to the Bernardi heat model [26], the heat production rate of the battery is calculated:”
MethodTemperature Characteristics Improvement of Power Battery Module for Electric Vehicles
Wang, J., Wu, Z., Deng, X., et al. (2013) · IEEE Vehicle Power and Propulsion Conference (VPPC) · doi:10.1109/vppc.2013.6671714 · Cited by 3
“The commonly used heating rate estimation model is developed by Bernardi [7].”
MethodThermal Issues in Lithium-Ion Batteries
Alavi-Soltani, S. R., Ravigururajan, T. S., & Rezac, M. E. (2006) · ASME International Mechanical Engineering Congress and Exposition (IMECE) · doi:10.1115/imece2006-15106 · Cited by 5
Simulating power deliverable from a Li-ion battery pack at low temperatures
Singh, V., Rabaa, R., & Reddy, C. V. (2015) · IEEE International Transportation Electrification Conference (ITEC-India) · doi:10.1109/itec-india.2015.7386892 · Cited by 3
Electrothermal behavior of lithium-ion batteries with different levels of power fade
Yang, Z., Patil, D., & Fahimi, B. (2017) · IEEE Transportation Electrification Conference and Expo · doi:10.1109/itec.2017.7993291 · Cited by 5
“Back in 1985, Dr Bernadi explained the thermal energy balance within battery systems [8].”
Method3.10 Electrochemical Energy Production
Dinçer, İ., Rosen, M. A., & Al‐Zareer, M. (2018) · Elsevier eBooks · doi:10.1016/b978-0-12-809597-3.00325-4 · Cited by 3
Inui, Y., Hirayama, S., & Tanaka, T. (2019) · IEEJ Transactions on Power and Energy · doi:10.1541/ieejpes.139.610 · Cited by 3
A thermal management method for lithium-ion battery based on fuzzy model predictive control
Zhuang, W., Liu, Z., Su, H., & Zhang, Q. (2019) · Chinese Automation Congress · doi:10.1109/cac48633.2019.8996265 · Cited by 3
“The energy balance[9] of lithium-ion battery in the lumped parameter framework is given by[10]:”
MethodStudy on heat dissipation structure of air-cooled Lithium ion battery module
Wang, J., Qin, D., & Wang, T. (2022) · Journal of Physics Conference Series · doi:10.1088/1742-6596/2174/1/012035 · Cited by 3
“It was not until 1985 that Bernadi[7-8] from University of California Berkeley simplified the battery thermal model and believed that the heat generated by the battery was composed of reversible reaction heat and irreversible heat.”
BackgroundLiu, C., Hu, M., Jin, G., Fu, C., Yang, H., & Jia, Q. (2022) · Journal of Energy Storage · doi:10.1016/j.est.2022.104566 · Cited by 4
Transport and Kinetic Phenomena Linked to Power Performance of Lithium-Ion Batteries.
Han, S. W. (2014) · Deep Blue (University of Michigan) · Cited by 4
Kim, Y. (2014) · Deep Blue (University of Michigan) · Cited by 4
Investigation into the Effect of Thermal Management on the Capacity Fade of Lithium-ion Batteries
Carnovale, A. (2017) · UWSpace (University of Waterloo) · Cited by 3
Wang, Y., Li, B., Hu, Y., et al. (2022) · SSRN Electronic Journal · doi:10.2139/ssrn.4122012 · Cited by 3
Lu, Y., Li, Y., Han, X., et al. (2024) · SSRN Electronic Journal · doi:10.2139/ssrn.4766704 · Cited by 3
Zhan, S., Huang, Y. F., Li, F., Yin, Y., & Liu, C. (2024) · Proceedings of the Institution of Mechanical Engineers Part D Journal of Automobile Engineering · doi:10.1177/09544070241265984 · Cited by 2
“…heat Q r , and auxiliary reaction heat Q s , 28 as follows: For the heat generation model of battery, Bernadi’s model is widely used at present 29 as shown below: where I is the battery current, U OC is the open circuit voltage, U is the terminal voltage, ∂ U OC ∂ T is the temperature…”
LiFePO4 Battery Thermal Modeling: Bus Bar Thermal Effects
Haas, M., Nemati, A., Moura, S. J., et al. (2024) · IFAC-PapersOnLine · doi:10.1016/j.ifacol.2025.01.108 · Cited by 2
Gao, Q., Tian, J. J., Bao, C., et al. (2024) · Science China Technological Sciences · doi:10.1007/s11431-024-2690-7 · Cited by 2
Optimal thermal management of lithium-ion battery packs using a fuzzy neural network controller
Li, D., An, Z., Zhou, Y., et al. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.116960 · Cited by 2
Zhu, Z., Zhang, D., Zheng, Y., et al. (2025) · Numerical Heat Transfer Part A Applications · doi:10.1080/10407782.2025.2525318 · Cited by 2
Hackmann, T., Emir, Y., & Danzer, M. A. (2025) · Energy and AI · doi:10.1016/j.egyai.2025.100569 · Cited by 4
Yuan, X., Xu, X., Qiu, C., et al. (2025) · International journal of mechanical system dynamics · doi:10.1002/msd2.70033 · Cited by 2
“Bernardi et al. [33] proposed a heat generation rate model for batteries in 1985, which is currently the most widely used computational model.”
Khan, R., Agarwal, P. K., & Acharya, S. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.118226 · Cited by 3
Understanding Heat Generation of LNMO Cathodes in Lithium-Ion Batteries via Entropy and Resistance
Böhm, K., Kondrakov, A., Markus, T., et al. (2025) · Batteries · doi:10.3390/batteries11100357 · Cited by 2
“The description of heat generation in lithium-ion batteries (LIBs) during cycling can be traced back to Bernardi et al. [27], who decomposed the total heat flux ˙ Q total into four contributions: the reversible heat flux ˙ Q rev , the irreversible heat flux ˙ Q irrev , the heat of mixing ˙ Q mix ,…”
Xu, Z., Jin-xin, T., Song, G., et al. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.118610 · Cited by 2
Torun, E., & Buyruk, E. (2025) · Journal of Thermal Analysis and Calorimetry · doi:10.1007/s10973-025-14794-5 · Cited by 2
“Bernardi et al. [31] stated in their study that the total heat produced in the battery can be expressed with the following formula.”
InfluentialDiker, İ., Ozkan, G. M., Gökciler, O. C., et al. (2025) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2025.110034 · Cited by 2
Metadata
- Authors
- Bernardi, D., Pawlikowski, E., & Newman, J.
- Affiliations
- University of California, Berkeley (US)
- ORCID
- Newman, J.
- Venue
- Journal of The Electrochemical Society
- Publisher
- The Electrochemical Society
- Published
- 1985-01-01
- Volume
- 132
- Issue
- 1
- Pages
- 5-12
- ISSN
- 0013-4651 (ISSN-L)
- 1945-7111
- OpenAlex
- W2023385933
- Cited by
- 2,548
- References
- 0
- Citations by year
- 2026: 383 · 2025: 387 · 2024: 339 · 2023: 265 · 2022: 238 · 2021: 167 · 2020: 147 · 2019: 106 · 2018: 74 · 2017: 89 · 2016: 42 · 2015: 53 · 2014: 75 · 2013: 51 · 2012: 31
- FWCI
- 0.00
- Type
- journal article
- Language
- en
- Open access
- bronze
- doi.org
- Licence
- iopscience.iop.org/page/copyright (vor, 12758 d)
- iopscience.iop.org/info/page/text-and-data-mining (tdm, 12758 d)
- Locations
- Journal of The Electrochemical Society (publishedVersion)
- Topics
- Physical Sciences › Engineering › Automotive Engineering › Battery Modeling and Management
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advancements in Battery Materials
- Physical Sciences › Chemistry › Electrochemistry › Molten salt chemistry and electrochemical processes
- Keywords
- heat generation rate, Joule heating, phase transitions, mixing effects, electrochemical reactions, battery thermal management, battery modeling
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.