A General Energy Balance for Battery Systems
Open accessThe DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index; 2 of the 20 sources its claims cite were checked for support.
Abstract
A general energy balance for battery systems has been developed. This equation is useful for estimating cell thermal characteristics. Reliable predictions of cell temperature and heat‐generation rate are required for the design and thermal management of battery systems. The temperature of a cell changes as a result of electrochemical reactions, phase changes, mixing effects, and joule heating. The equation developed incorporates these effects in a complete and general manner. Simplifications and special cases are discussed. The results of applying the energy balance to a mathematical model of the cell discharged through two different reaction mechanisms are given as examples. The examples illustrate how the energy equation may be applied to a specific system to examine the relative contributions corresponding to the terms in the equation. The examples show that the processes involved in cell heat generation may be complex and that the application of a sufficiently general energy equation is advantageous.
Overview
CoChat Summary
TL;DR
The paper derives a general energy balance for battery systems that includes mixing, phase changes, and simultaneous electrochemical reactions with composition-dependent open-circuit potentials. It applies the equation to a modeled LiAl/LiCl-KCl/FeS cell discharged by two mechanisms and to a lead-acid estimate, showing that cell heat generation can be complex and that a sufficiently general energy equation is advantageous.
Key findings
- A general energy balance is developed that includes energy contributions from mixing, phase changes, and simultaneous electrochemical reactions with composition-dependent open-circuit potentials; prior treatments were restricted to single pure-phase reactants or a single reaction without mixing effects.
- For the LiAl/FeS model, adiabatic-reversible discharge gives the same temperature at 100% depth of discharge for both mechanisms because the overall reaction is the same; slope discontinuities occur at 50% and 12% utilization for mechanisms 1 and 2, respectively. In the realistic simulations, the second reaction begins at 30% and 11% utilization for mechanisms 1 and 2, respectively.
- The mixing term is negligible in the LiAl/FeS example; at 25% utilization, the temperature decline after current interruption is only about 0.2 K. For a lead-acid cell, the estimated temperature rise after full discharge is approximately 1.6 K, or 2.9 K if 1.25 mol of PbO2 is allowed for discharge.
- The sign of the mixing effect depends on the enthalpy curve: for lead-acid, the sulfuric acid-water enthalpy curve is concave upward, so a well-insulated cell heats after current interruption; for the high-temperature LiCl-KCl cell, the curve is concave downward, so the cell cools after interruption. Neglecting mixing overestimates lead-acid operating temperature and underestimates high-temperature cell operating temperature.
Methods
- The paper derives the energy balance from the first law of thermodynamics, assuming uniform battery temperature, and presents a final general equation including reaction, heat-capacity, phase-change, mixing, electrical-work, and heat-transfer terms.
- The equation is applied to an existing one-dimensional mathematical model of the LiAl/LiCl-KCl/FeS cell with a porous LiAl negative electrode, porous FeS positive electrode, electrolyte reservoir, and separator under galvanostatic discharge, using the two reaction mechanisms in Table I.
- Appendix A estimates the lead-acid temperature rise using an assumed uniform 5 molal sulfuric acid electrolyte, with one-third of the electrolyte in the cathode and anode spaces and one-third between the electrodes; the analysis compares adiabatic-reversible profiles with model simulations and examines the relative contributions of terms.
Limitations
- The paper states that the rigorous energy balance is difficult to apply without a detailed mathematical model because instantaneous composition profiles and current fractions are required; in practice, obtaining concentration profiles and predicting current partitioning among possible reactions is difficult.
- The paper states that the analysis does not include enthalpy changes from nonfaradaic reactions; self-discharge or corrosion must be divided into anodic and cathodic components and included as an additional term. The mixing term is also difficult because it involves integrations of concentration profiles.
- The paper states that actual FeS discharge is complicated and more like a mixture of the two proposed mechanisms plus simultaneously occurring chemical reactions; the examples are model simulations. The lead-acid estimate assumes artificial concentration jumps at interfaces, and diffusion would lower the estimate; nonuniform reaction distribution in porous electrodes would make the concentration distribution nonuniform. The breakdown is presented only up to 30% utilization because oscillatory behavior begins when the second reaction starts, to be treated in a subsequent publication.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
0 Valid · 5 Not valid · 12 Not checked · 75 Own results and interpretations
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“Basing the discharge on two Farādays (1 mol PbOg) and a transference number of 0.74 for hydrogen ion, we may calculate that the concentration in the cathode space and anode space drops to 1.04 and 2.79 molal, respectively (14).”
What the sources say
- Could not verifycites [14] 14. Hans Bode, "Lead-Acid Batteries," R. J. Brodd and K. V. Kordesch, Translators, Wiley-Interscience, New York (1977). sourceExperimental — accuracy not yet measured
The available text in the book-review passage (section labeled “Notice to Members April 1 is Cut-Off Date”; page not provided) describes the book’s theoretical treatment of lead-acid batteries but does not give this calculation. Searches for the 0.74 hydrogen-ion transference number, two Faradays, and the 1.04 and 2.79 molal concentrations found no passage addressing the claimed values. (LLM, conf=0.76)
hedgedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 5 assumptions not shown here.
- Could not verify
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“The temperature rise, after full discharge, is approximately 1.6 K.”
- Also stated in: § Estimate of the Temperature Rise in a Lead-Acid Cell Following Current Interruption · p. 8 · hedged
“Using the data available in Ref. (14) (for 298 K), we calculate the temperature rise to be about 1.6 K”
What the sources say
- Could not verifycites [14] 14. Hans Bode, "Lead-Acid Batteries," R. J. Brodd and K. V. Kordesch, Translators, Wiley-Interscience, New York (1977). sourceExperimental — accuracy not yet measured
The available passages from the book review (page not provided) describe the book’s coverage of lead-acid battery thermodynamics but give no temperature rise after full discharge. Searches for “1.6 K” and the discharge-temperature claim found no supporting passage in our copy. (LLM, conf=0.75)
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 5 assumptions not shown here.
- Also stated in: § Estimate of the Temperature Rise in a Lead-Acid Cell Following Current Interruption · p. 8 · hedged
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Although the mixing term offers a negligible contribution to the energy balance, it is interesting to investigate the processes that determine its behavior.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The profile for the X-phase mechanism in Fig. 1 follows the adiabatic-reversible profile up to about 5% utilization because the heat-loss contribution tends to cancel the polarization heat.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“A general energy balance for battery systems has been developed.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 3 assumptions not shown here.
39 more claims
Create a free account to see all 92 claims and every source verdict.
- It may state two separate claims as one. 20
- Probably not a substantial claim. 33
- The quote only partly states this claim. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Conclusions · p. 8
“Equation [23], written for a single cell reaction, is the energy equation most commonly used in battery applications.”
§ Discussion of Terms · p. 5
“Furthermore, Eq. [24] is the form of the energy balance that is most commonly encountered in the literature.”
Citations
Cites
The publisher hasn’t deposited this paper’s reference list.
Research works printed but not linked: 12
- [1]1. J. M. Sherfey and A. Brenner, This Journal, 105, 665 (1958).
- [3]3. H. F. Gibbard, This Journal, 125, 353 (1978).
- [2]2. S. Gross, Energy Convers., 9, 55 (1969).
- [4]4. I. A. Dibrov and V. A. Bykov, Sov. Electrochem., 13, 298 (1977).
- [6]6. L. D. Hansen and R. M. Hart, This Journal, 125, 842 (1978).
- [5]5. I. A. Dibrov and V. A. Bykov, J. Appl. Chem., 49, 2025 (1977).
- [7]7. F. B. Tudron, ibid., 128, 516 (1981).
- [9]9. W. H. Tiedemann and J. Newman, in "Battery Design and Optimization," S. Gross, Editor, pp. 23-38, The Electrochemical Society Softbound Proceedings Series, Princeton, NJ (1979).
- [8]8. D. M. Chen and H. F. Gibbard, ibid., 130, 1975 (1983).
- [10]10. Richard Pollard and John Newman, This Journal, 128, 491 (1981).
- [11]11. Richard Pollard and John Newman, ibid., 128, 502 (1981).
- [13]13. Z. Tomczuk, S. K. Preto, and M. F. Roche, This Journal, 128, 760 (1981).
Cited by
Items 301–400 of 2,542
Fan, Z., Gao, R., & Liu, S. (2022) · Energy · doi:10.1016/j.energy.2022.125091 · Cited by 99
Quantitative measurement of thermal performance of a cylindrical lithium-ion battery
Sheng, L., Zhang, C., Xu, J., Zhou, Q., & Zhang, X. (2024) · Measurement · doi:10.1016/j.measurement.2024.115458 · Cited by 118
Faenza, N. V., Lebens-Higgins, Z. W., Mukherjee, P., Sallis, S., Pereira, N., Badway, F., Halajko, A., Ceder, G., Cosandey, F., Piper, L. F. J., et al. (2017) · Langmuir · doi:10.1021/acs.langmuir.7b00863 · Cited by 93
A Surface Temperature Estimation Method for Lithium-Ion Battery Using Enhanced GRU-RNN
Yao, Q., Lu, D. D., & Lei, G. (2022) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2022.3197927 · Cited by 104
“A commonly adopted expression for heat generation ( Q ) in a lithium-ion battery is which is a simplified equation proposed by Bernardi et al. [18].”
BackgroundEffect of different cooling configurations on thermal gradients inside cylindrical battery cells
Bolsinger, C., & Birke, K. P. (2018) · Journal of Energy Storage · doi:10.1016/j.est.2018.11.030 · Cited by 91
Jiaqiang, E., Feng, Y., Li, W., Zhang, B., Zuo, H., Wei, K., Chen, J., Zhu, H. Y., Zhu, H., & Deng, Y. (2021) · Energy · doi:10.1016/j.energy.2021.120336 · Cited by 93
Optimization of air-cooling technology for LiFePO4 battery pack based on deep learning
Shi, Y., Ahmad, S., Liu, H., Lau, K. T., & Zhao, J. (2021) · Journal of Power Sources · doi:10.1016/j.jpowsour.2021.229894 · Cited by 93
A computational multi-node electro-thermal model for large prismatic lithium-ion batteries
Pan, Y.-W., Hua, Y., Zhou, S., He, R., Zhang, Y., Yang, S., Liu, X., Lian, Y., Yan, X., & Wu, B. (2020) · Journal of Power Sources · doi:10.1016/j.jpowsour.2020.228070 · Cited by 91
“Al [24], the reversible heat can be written as:”
BackgroundDu, S., Jia, M., Cheng, Y., Tang, Y., Zhang, H., Ai, L., Zhang, K., & Lai, Y. (2014) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2014.11.018 · Cited by 92
Werner, D., Loges, A., Becker, D. J., & Wetzel, T. (2017) · Journal of Power Sources · doi:10.1016/j.jpowsour.2017.07.105 · Cited by 96
Paccha-Herrera, E., Calderón-Muñoz, W. R., Orchard, M. E., Jaramillo, F., & Medjaher, K. (2020) · Batteries · doi:10.3390/batteries6030040 · Cited by 110
Ma, Y., Ding, H., Liu, Y., & Gao, J. (2021) · Energy · doi:10.1016/j.energy.2021.122571 · Cited by 91
An LSTM-PINN Hybrid Method to Estimate Lithium-Ion Battery Pack Temperature
Cho, G., Zhu, D., Campbell, J. J., & Wang, M. (2022) · IEEE Access · doi:10.1109/access.2022.3208103 · Cited by 95
“Unlike the other 607 researchers who treat the chamber temperature as a constant 608 in [25], we use it as one of the inputs.”
BackgroundFong, K. D., Bergstrom, H. K., McCloskey, B. D., & Mandadapu, K. K. (2020) · AIChE Journal · doi:10.1002/aic.17091 · Cited by 107
“The classic text of Newman and Thomas-Alyea [6] and related works [19,20] introduce Stefan-Maxwell and Onsager-like transport equations for electrolytes, albeit without discussion of the momentum, energy, and entropy balances of continuous media upon which these equations are built.”
BackgroundStudy on a liquid cooled battery thermal management system pertaining to the transient regime
Huang, Y., Wang, S., Lu, Y., Huang, R. N., & Yu, X. (2020) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2020.115793 · Cited by 85
Mei, W., Li, H., Zhao, C., Sun, J., & Wang, Q. (2020) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2020.120319 · Cited by 96
Sturm, J., Frank, A., Rheinfeld, A., Erhard, S. V., & Jossen, A. (2020) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/abb40c · Cited by 91
Wei, Z., Zhao, J., Skyllas‐Kazacos, M., et al. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.02.108 · Cited by 88
Zhuang, Y., Chen, T., Chen, J., Li, J., Guan, M., & Chen, Y. (2021) · Thermal Science and Engineering Progress · doi:10.1016/j.tsep.2021.101094 · Cited by 99
Fen, L., Wang, J., Liu, Y., Wang, F., Chen, Y., Lu, Y., Liu, H., Du, Q., Sun, F., & Yang, N. (2022) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2022.118311 · Cited by 92
Heat transfer in the dynamic cycling of lithium–titanate batteries
Wang, Q., Sun, Q., Ping, P., et al. (2015) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2015.11.007 · Cited by 86
Dong, F., Cheng, Z., Zhu, J.-W., Song, D., & Ni, J. (2021) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2021.116758 · Cited by 86
Ma, Y., Ding, H., Mou, H., & Gao, J. (2021) · Measurement · doi:10.1016/j.measurement.2021.110115 · Cited by 88
Measurement of Multiscale Thermal Transport Phenomena in Li-Ion Cells: A Review
Shah, K., Vishwakarma, V., & Jain, A. (2016) · Journal of Electrochemical Energy Conversion and Storage · doi:10.1115/1.4034413 · Cited by 91
Bruggeman's Exponents for Effective Thermal Conductivity of Lithium-Ion Battery Electrodes
Vadakkepatt, A., Trembacki, B. L., Mathur, S. R., & Murthy, J. Y. (2015) · Journal of The Electrochemical Society · doi:10.1149/2.0151602jes · Cited by 90
Heat Generation and Thermal Transport in Lithium-Ion Batteries: A Scale-Bridging Perspective
Kantharaj, R., & Marconnet, A. M. (2019) · Nanoscale and Microscale Thermophysical Engineering · doi:10.1080/15567265.2019.1572679 · Cited by 97
“The heat generation rate is often determined using the following simplified expression ignoring heat generation from mixing and phase change (adapted from [24]):”
BackgroundInfluentialAnalysis of the Heat Generation Rate of Lithium-Ion Battery Using an Electrochemical Thermal Model
Song, M., Hu, Y., Choe, S.-Y., et al. (2020) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/aba96b · Cited by 85
Laadjal, K., & Cardoso, A. J. M. (2021) · Electronics · doi:10.3390/electronics10131588 · Cited by 101
“Thus, several studies carried out in this field of study are based on equations drawn from the thermodynamic study of chemical reactions in a cell [61].”
BackgroundKiani, M., Omiddezyani, S., Nejad, A. M., Ashjaee, M., & Houshfar, E. (2021) · Case Studies in Thermal Engineering · doi:10.1016/j.csite.2021.101539 · Cited by 91
Chen, Y., & Evans, J. W. (1994) · Electrochimica Acta · doi:10.1016/0013-4686(94)80095-2 · Cited by 100
A Spatiotemporal Estimation Method for Temperature Distribution in Lithium-Ion Batteries
Liu, Z., & Li, H. (2014) · IEEE Transactions on Industrial Informatics · doi:10.1109/tii.2014.2341955 · Cited by 87
“The proposed estimation and prediction method could be easily implemented in the existing vehicle BMS.”
MethodBhattacharjee, A., Mohanty, R. K., & Ghosh, A. (2020) · Energies · doi:10.3390/en13215695 · Cited by 93
Ye, J., Aldaher, A. Y. M., & Tan, G. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.108766 · Cited by 84
Hatzell, K. B., Sharma, A., & Fathy, H. K. (2012) · 2012 American Control Conference (ACC) · doi:10.1109/acc.2012.6315578 · Cited by 84
“address these challenges by combining energy balance equations [32] with a model of battery electro-”
MethodTransient three-dimensional thermal model for batteries with thin electrodes
Taheri, P., Yazdanpour, M., & Bahrami, M. (2013) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.05.175 · Cited by 92
Bai, Y., Li, L., Li, Y., Chen, G., Zhao, H., Wang, Z., Wu, C. K., Ma, H., Wang, X., Cui, H., et al. (2018) · Journal of Energy Chemistry · doi:10.1016/j.jechem.2018.02.016 · Cited by 89
Core temperature estimation based on electro‐thermal model of lithium‐ion batteries
Chen, L., Hu, M., Cao, K., Li, S., Su, Z., Jin, G., & Fu, C. (2020) · International Journal of Energy Research · doi:10.1002/er.5281 · Cited by 92
Wu, X., Lu, Y., Ouyang, H., Ren, X., Yang, J., Guo, H., Han, X., Zhang, C., & Wu, Y. (2024) · Energy Conversion and Management · doi:10.1016/j.enconman.2024.118478 · Cited by 92
Thermal analysis of large-capacity LiFePO4 power batteries for electric vehicles
Lin, C., Xu, S., Zhao, L., Li, B., Chang, G., & Liu, J. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2015.06.129 · Cited by 85
Huang, H., Wang, H., Gu, J., & Wu, Y. (2019) · Energy Conversion and Management · doi:10.1016/j.enconman.2019.04.013 · Cited by 83
Yi, Y., Xia, C., Feng, C., Zhang, W., Fu, C., Qian, L., & Chen, S. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.107203 · Cited by 89
Zou, Z., Xie, J., Luo, Y., et al. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.110634 · Cited by 82
Chen, X., Yan, S., Wang, D., Han, J., Guan, Z., Yin, Y., Yang, S., & Dong, H. (2024) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2024.126246 · Cited by 86
Electro-thermal characterization of Lithium Iron Phosphate cell with equivalent circuit modeling
Saw, L. H., Ye, Y., & Tay, A. A. O. (2014) · Energy Conversion and Management · doi:10.1016/j.enconman.2014.07.011 · Cited by 86
Fang, K., Mu, D., Chen, S., et al. (2012) · Journal of Power Sources · doi:10.1016/j.jpowsour.2012.02.059 · Cited by 81
A novel resistance-based thermal model for lithium-ion batteries
Xie, Y., Li, W., Yang, Y. M., & Feng, F. (2018) · International Journal of Energy Research · doi:10.1002/er.4193 · Cited by 85
“1⁄4 I(2) ∑5j1⁄41∑5i1⁄41aijsocT j−1 þ∑6j1⁄41∑6i1⁄41bijsocT þIT dT : (13)”
MethodNovel Mesoscale Electrothermal Modeling for Lithium-Ion Batteries
Xie, Y., Li, W., Hu, X., Zou, C., Feng, F., & Tang, X. (2019) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2019.2927014 · Cited by 82
“constructed a pioneering thermal model for Li-ion batteries in 1985 [7], researchers over the world have been making great efforts to study the relationship among the heat generation, electrical work, and enthalpy change.”
BackgroundJindal, P., Kumar, B. S., & Bhattacharya, J. (2021) · Journal of Energy Storage · doi:10.1016/j.est.2021.102619 · Cited by 81
Allu, S., Kalnaus, S., Elwasif, W. R., Simunovic, S., Turner, J., & Pannala, S. (2013) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.08.040 · Cited by 81
Park, S., & Ahn, C. (2020) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2020.2999939 · Cited by 91
Xin, Q., Yang, T., Zhang, H., et al. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.108003 · Cited by 80
Peng, R., Kong, D., Ping, P., Wang, G., Gao, X., Lv, H., Zhao, H., He, X., Zhang, Y., & Dai, X. (2024) · Energy storage materials · doi:10.1016/j.ensm.2024.103417 · Cited by 133
Qi, W., Yang, J., Zhang, Z., Wu, J., Peng, L., & Xiang, S. (2025) · Energy Conversion and Management · doi:10.1016/j.enconman.2025.119962 · Cited by 84
In Situ Measurements of Heat Generation in a Li/Mesocarbon Microbead Half-Cell
Lu, W., & Prakash, J. (2003) · Journal of The Electrochemical Society · doi:10.1149/1.1541672 · Cited by 85
Zhang, X., Chang, X., Shen, Y., & Xiang, Y. (2017) · Journal of Energy Storage · doi:10.1016/j.est.2017.03.008 · Cited by 83
Simulation of temperature rise in Li-ion cells at very high currents
Mao, J., TIEDEMANN, W. H., & Newman, J. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.08.033 · Cited by 81
Self-citationLiu, Z., Liu, X., Meng, H., Guo, L., & Zhang, Z. (2021) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2021.121338 · Cited by 78
A Thermal Runaway Simulation on a Lithium Titanate Battery and the Battery Module
Chen, M., Sun, Q., Li, Y., Wu, K., Liu, B., Peng, P., & Wang, Q. (2015) · Energies · doi:10.3390/en8010490 · Cited by 77
“During battery charging/discharging, various chemical and electrochemical reactions as well as transport processes take place, and the internal system follows the charge conservation, lithium ion diffusion, Butler-Volmer law [1,7,8,11,12] in the one-dimensional cell model, which is used to model the Li-ion battery che…”
BackgroundMethodTemperature Rise in Prismatic Polymer Lithium-Ion Batteries: An Analytic Approach
Taheri, P., & Bahrami, M. (2012) · SAE International journal of passenger cars. Electronic and electrical systems · doi:10.4271/2012-01-0334 · Cited by 84
Ding, Y., Wei, M., & Liu, R. (2020) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2020.116494 · Cited by 77
Akbarzadeh, M., Kalogiannis, T., Jin, L., Karimi, D., Mierlo, J. V., & Berecibar, M. (2022) · Journal of Energy Storage · doi:10.1016/j.est.2022.104673 · Cited by 79
Verma, A., & Rakshit, D. (2022) · Thermal Science and Engineering Progress · doi:10.1016/j.tsep.2022.101314 · Cited by 84
A novel battery thermal management system based on P type triply periodic minimal surface
Fan, Z., Gao, R., & Liu, S. (2022) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2022.123090 · Cited by 87
State estimation of lithium-ion cells using a physicochemical model based extended Kalman filter
Sturm, J., Ennifar, H., Erhard, S. V., Rheinfeld, A., Kosch, S., & Jossen, A. (2018) · Applied Energy · doi:10.1016/j.apenergy.2018.04.011 · Cited by 78
Shengxin, E., Liu, Y., Cui, Y., Wu, A., & Yin, H. (2023) · Energy · doi:10.1016/j.energy.2023.129074 · Cited by 75
Zhang, F., Gou, H., Xie, C., He, Y., Zhu, Y., Lu, F., Liang, B., & Xiao, K. (2022) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2022.118439 · Cited by 75
Zhang, X., Li, P., Huang, B., & Zhang, H. (2022) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2022.123449 · Cited by 81
Tang, Y., Wu, L., Wei, W. F., Wen, D., Guo, Q., Liang, W., & Li, X. (2018) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2018.03.067 · Cited by 77
Lin, C., Xu, S., & Liu, J. (2018) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2018.03.057 · Cited by 76
Karimi, D., Behi, H., Hosen, M. S., Jaguemont, J., Berecibar, M., & Mierlo, J. V. (2020) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2020.116449 · Cited by 72
A Review on Thermal Behaviors and Thermal Management Systems for Supercapacitors
Zhou, W., Liu, Z., Chen, W., Sun, X., Luo, M., Zhang, X., Li, C., An, Y., Song, S., Wang, K., et al. (2023) · Batteries · doi:10.3390/batteries9020128 · Cited by 82
A review of thermal management methods for electric vehicle batteries based on heat pipes and PCM
Thawkar, V., & Dhoble, A. S. (2023) · Journal of the Brazilian Society of Mechanical Sciences and Engineering · doi:10.1007/s40430-023-04021-3 · Cited by 74
“The Bernardi model has become increasingly commonly utilized in the evaluation and modeling of heat generation in lithium-ion batteries due to the availability of these parameters [24].”
MethodWu, M.-S. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.108362 · Cited by 77
Shengxin, E., Cui, Y., Liu, Y., & Yin, H. (2023) · Energy · doi:10.1016/j.energy.2023.128805 · Cited by 74
Arora, S., Shen, W., & Kapoor, A. (2017) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2017.02.044 · Cited by 72
Mei, W., Duan, Q., Lu, W. D., Sun, J., & Wang, Q. (2020) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2020.122643 · Cited by 75
Kleiner, J., Stuckenberger, M., Komsiyska, L., & Endisch, C. (2021) · Journal of Energy Storage · doi:10.1016/j.est.2021.102588 · Cited by 72
A lightweight liquid cooling thermal management structure for prismatic batteries
Tang, Z., Liu, Z., Li, J., & Cheng, J. (2021) · Journal of Energy Storage · doi:10.1016/j.est.2021.103078 · Cited by 76
Thermal performance of aluminum vapor chamber for EV battery thermal management
Kim, J. S., Shin, D. H., You, S. M., & Lee, J. (2020) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2020.116337 · Cited by 70
Li, X., Huang, J., & Faghri, A. (2016) · Journal of Power Sources · doi:10.1016/j.jpowsour.2016.09.127 · Cited by 74
Local Heat Generation in a Single Stack Lithium Ion Battery Cell
Heubner, C., Schneider, M., Lämmel, C., & Michaelis, A. (2015) · Electrochimica Acta · doi:10.1016/j.electacta.2015.10.182 · Cited by 74
Advances and challenges of integrated thermal management technologies for pure electric vehicles
Liang, K., Wang, M., Gao, C., Dong, B., Feng, C., Zhou, X. J., & Liu, J. (2021) · Sustainable Energy Technologies and Assessments · doi:10.1016/j.seta.2021.101319 · Cited by 85
Numerical analysis of topology-optimized cold plates for thermal management of battery packs
Liu, Z., Zhao, H., Qiu, Y., et al. (2023) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2023.121983 · Cited by 70
Pilali, E., Soltani, M., Hatefi, M., Shafiei, S., Salimi, M., & Amidpour, M. (2025) · Journal of Power Sources · doi:10.1016/j.jpowsour.2025.236345 · Cited by 83
Northrop, P. W. C., Pathak, M., Rife, D., De, S., Santhanagopalan, S., & Subramanian, V. R. (2015) · Journal of The Electrochemical Society · doi:10.1149/2.0341506jes · Cited by 82
Kosch, S., Rheinfeld, A., Erhard, S. V., & Jossen, A. (2017) · Journal of Power Sources · doi:10.1016/j.jpowsour.2016.12.110 · Cited by 72
The Cell Cooling Coefficient: A Standard to Define Heat Rejection from Lithium-Ion Batteries
Hales, A., Diaz, L. B., Marzook, M. W., Zhao, Y., Patel, Y., & Offer, G. J. (2019) · Journal of The Electrochemical Society · doi:10.1149/2.0191912jes · Cited by 80
Yeow, K. F., Teng, H., Thelliez, M., et al. (2012) · SAE International journal of alternative powertrains · doi:10.4271/2012-01-0331 · Cited by 69
Zhu, T., Min, H., Yu, Y., Zhao, Z., Xu, T., Chen, Y., Li, X., & Zhang, C. (2017) · Energies · doi:10.3390/en10020243 · Cited by 73
“Heat generated by the battery during its working process could be divided into four parts [34]: reaction heat ( ), side reaction heat ( ), polarization reaction heat ( ) and Joule heat ( ), as shown in Equation (5): = + + + (5)”
BackgroundPan, D., Guo, H., Tang, S., Li, X., Wang, Z., Peng, W., Wang, J., & Yan, G. (2020) · Journal of Power Sources · doi:10.1016/j.jpowsour.2020.228174 · Cited by 69
Cheng, J., Shuai, S., Tang, Z., et al. (2022) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2022.119694 · Cited by 69
Bhutto, Y. A., Pandey, A. K., Saidur, R., Sharma, K., & Tyagi, V. V. (2023) · Materials Today Sustainability · doi:10.1016/j.mtsust.2023.100443 · Cited by 92
Sutheesh, P. M., Nichit, R. B., & Bandaru, R. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.109972 · Cited by 74
Yang, H., Liu, N., Li, M., Gu, M. D., & Gao, Q. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.126416 · Cited by 70
Murashko, K., Pyrhonen, J. J., & Laurila, L. I. E. (2013) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2013.2255291 · Cited by 70
Simulation of heat generation in a reconstructed LiCoO2 cathode during galvanostatic discharge
Yan, B., Lim, C., Yin, L., & Zhu, L. (2013) · Electrochimica Acta · doi:10.1016/j.electacta.2013.03.132 · Cited by 75
Zhang, Y., & Guo, B. (2015) · Energies · doi:10.3390/en81112320 · Cited by 68
“[35]: Q “ I Voltotal ˆ”
Sakti, A., Gallagher, K. G., Sepulveda, N. A., Uçkun, C., Vergara, C., de Sisternes, F. J., Dees, D. W., & Botterud, A. (2016) · Journal of Power Sources · doi:10.1016/j.jpowsour.2016.12.063 · Cited by 72
Thermal management system of lithium-ion battery module based on micro heat pipe array
Ye, X., Zhao, Y., & Quan, Z. (2017) · International Journal of Energy Research · doi:10.1002/er.3847 · Cited by 69
Researches on Modeling and Experiment of Li-ion Battery PTC Self-heating in Electric Vehicles
Jin, X., Li, J.-Q., Zhang, C.-N., & Wu, P.-E. (2016) · Energy Procedia · doi:10.1016/j.egypro.2016.12.012 · Cited by 68
Metadata
- Authors
- Bernardi, D., Pawlikowski, E., & Newman, J.
- Affiliations
- University of California, Berkeley (US)
- ORCID
- Newman, J.
- Venue
- Journal of The Electrochemical Society
- Publisher
- The Electrochemical Society
- Published
- 1985-01-01
- Volume
- 132
- Issue
- 1
- Pages
- 5-12
- ISSN
- 0013-4651 (ISSN-L)
- 1945-7111
- OpenAlex
- W2023385933
- Cited by
- 2,548
- References
- 0
- Citations by year
- 2026: 383 · 2025: 387 · 2024: 339 · 2023: 265 · 2022: 238 · 2021: 167 · 2020: 147 · 2019: 106 · 2018: 74 · 2017: 89 · 2016: 42 · 2015: 53 · 2014: 75 · 2013: 51 · 2012: 31
- FWCI
- 0.00
- Type
- journal article
- Language
- en
- Open access
- bronze
- doi.org
- Licence
- iopscience.iop.org/page/copyright (vor, 12758 d)
- iopscience.iop.org/info/page/text-and-data-mining (tdm, 12758 d)
- Locations
- Journal of The Electrochemical Society (publishedVersion)
- Topics
- Physical Sciences › Engineering › Automotive Engineering › Battery Modeling and Management
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advancements in Battery Materials
- Physical Sciences › Chemistry › Electrochemistry › Molten salt chemistry and electrochemical processes
- Keywords
- heat generation rate, Joule heating, phase transitions, mixing effects, electrochemical reactions, battery thermal management, battery modeling
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.